DM36x initialization passed! TI UBL Version: 1.50 Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000019. DONE Jumping to entry point at 0x81080000. U-Boot 1.3.4 (May 22 2009 - 11:25:39) I2C: ready DRAM: 128 MB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 2048 MiB In: serial Out: serial Err: serial EEPROM @ 0x50 read FAILED!!! Ethernet PHY: GENERIC @ 0x00 Hit any key to stop autoboot: 0 DM365 EVM :> DM365 EVM :> DM365 EVM :> DM365 EVM :>printenv baudrate=115200 bootfile="uImage" ethaddr=00:01:02:03:04:05 bootdelay=3 filesize=1FFB38 fileaddr=80700000 ipaddr=192.168.1.228 serverip=192.168.1.3 bootcmd=nboot 0x80700000 0 0x400000; bootm bootargs=mem=70M console=ttyS0,115200n8 root=/dev/mtdblock3 rw rootfstype=yaffs2 ip=192.168.1.228:192.168.1.3:192.168.1.1:255.255.255.0::eth0:off eth=00:40:01:2B:64:60 video=davincifb:vid0=OFF:vid1=OFF:osd0=720x576x16,4050K dm365_imp.oper_mode=0 davinci_capture.device_type=1 davinci_enc_mngr.ch0_mode=pal stdin=serial stdout=serial stderr=serial ver=U-Boot 1.3.4 (May 22 2009 - 11:25:39) Environment size: 580/262140 bytes DM365 EVM :>setenv bootargs 'mem=70M console=ttyS0,115200n8 root=/dev/mtdblock3 rw rootfstype=yaffs2 ip=192.168.1.228:192.168.1.3:192.168.1.1:255.255.255.0::eth0:off eth=00:40:01:2B:64:60 video=davincifb:vid0=OFF:vid1=OFF:osd0=720x576x16,4050K dm365_imp.oper_mode=0 davinci_capture.device_type=1 davinci_enc_mngr.ch0_mode=pal' DM365 EVM :>saveenv Saving Environment to NAND... Erasing Nand... Erasing at 0x3c0000 -- 100% complete. Writing to Nand... done DM365 EVM :>bootm ## Booting kernel from Legacy Image at 80700000 ... Image Name: Linux-2.6.32.17-davinci1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2095864 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................................... done, booting the kernel. Linux version 2.6.32.17-davinci1 (root@punuo-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #4 PREEMPT Fri Aug 17 17:28:45 CST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM36x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm36x_rev1.2 variant 0x8 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 17780 Kernel command line: mem=70M console=ttyS0,115200n8 root=/dev/mtdblock3 rw rootfstype=yaffs2 ip=192.168.1.228:192.168.1.3:192.168.1.1:255.255.255.0::eth0:off eth=00:40:01:2B:64:60 video=davincifb:vid0=OFF:vid1=OFF:osd0=720x576x16,4050K dm365_imp.oper_mode=0 davinci_capture.device_type=1 davinci_enc_mngr.ch0_mode=pal PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 70MB = 70MB total Memory: 66380KB available (3936K code, 389K data, 132K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 147.86 BogoMIPS (lpj=739328) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 8 gpio irqs NET: Registered protocol family 16 davinci_serial_init:97: failed to get UART2 clock EVM: HD imager video input bio: create slab at 0 DM365 IPIPE initialized in Continuous mode SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pca9543a_probe vpss vpss: dm365_vpss vpss probed vpss vpss: dm365_vpss vpss probe success dm365_afew_hw_init ch0 default output "COMPOSITE", mode "PAL" VPBE Encoder Initialized cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US LogicPD encoder initialized Switching to clocksource timer0_1 musb_hdrc: version 6.0, cppi-dma, host, debug=0 musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. msgmni has been set to 129 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) Console: switching to colour frame buffer device 90x36 davincifb davincifb.0: dm_osd0_fb: 720x576x16@0,0 with framebuffer size 4050KB davincifb davincifb.0: dm_vid0_fb: 0x0x16@0,0 with framebuffer size 1224KB davincifb davincifb.0: dm_osd1_fb: 720x576x4@0,0 with framebuffer size 810KB davincifb davincifb.0: dm_vid1_fb: 0x0x16@0,0 with framebuffer size 1224KB DM365 IPIPEIF probed imp serializer initialized davinci_previewer initialized davinci_resizer initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A console [ttyS0] enabled brd: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) 2 NAND chips detected Bad block table not found for chip 0 Bad block table not found for chip 1 Bad block table not found for chip 0 Bad block table not found for chip 1 Scanning device for bad blocks Bad eraseblock 2943 at 0x00002dfc0000 Scanning device for bad blocks Bad eraseblock 7039 at 0x00006dfc0000 Creating 5 MTD partitions on "davinci_nand.0": 0x000000000000-0x0000003c0000 : "bootloader" 0x0000003c0000-0x000000400000 : "params" 0x000000400000-0x000000800000 : "kernel" 0x000000800000-0x000020800000 : "filesystem1" 0x000020800000-0x000080000000 : "filesystem2" davinci_nand davinci_nand.0: controller rev. 2.3 spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 8 KByte at25640 eeprom, pagesize 32 spi_davinci spi_davinci.0: Controller at 0xfec66000 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest input: DM365 EVM Controls as /devices/platform/i2c_davinci.1/i2c-1/1-0025/input/input0 i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths7303 1-002c: ths7303 write failed ths7303: probe of 1-002c failed with error -121 vpfe_init vpfe-capture: vpss clock vpss_master enabled vpfe-capture vpfe-capture: v4l2 device registered vpfe-capture vpfe-capture: video device registered EVM: switch to tvp5146 SD video input tvp514x 1-005d: tvp514x 1-005d decoder driver registered !! vpfe-capture vpfe-capture: v4l2 sub device tvp5146 registered EVM: switch to tvp7002 HD video input vpfe-capture vpfe-capture: v4l2 sub device tvp7002 register fails EVM: switch to tvp7002 HD video input ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) ths7353 1-002e: No platform data!! ths7353 1-002e: ths7353 write failed ths7353: probe of 1-002e failed with error -121 vpfe-capture vpfe-capture: v4l2 sub device ths7353 register fails vpfe_register_ccdc_device: DM365 ISIF DM365 ISIF is registered with vpfe. af major#: 252, minor# 0 AF Driver initialized aew major#: 251, minor# 0 AEW Driver initialized Trying to register davinci display video device. layer=c30b7400,layer->video_dev=c30b7570 Trying to register davinci display video device. layer=c30b7800,layer->video_dev=c30b7970 davinci_init:DaVinci V4L2 Display Driver V1.0 loaded watchdog watchdog: heartbeat 60 sec davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x No device for DAI davinci-i2s asoc: tlv320aic3x <-> davinci-i2s mapping ok ALSA device list: #0: DaVinci EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 lib80211: common routines for IEEE802.11 drivers Clocks: disable unused mmcsd1 Clocks: disable unused spi1 Clocks: disable unused spi2 Clocks: disable unused spi3 Clocks: disable unused spi4 Clocks: disable unused pwm0 Clocks: disable unused pwm1 Clocks: disable unused pwm2 Clocks: disable unused pwm3 Clocks: disable unused timer1 Clocks: disable unused timer3 Clocks: disable unused emac Clocks: disable unused voice_codec Clocks: disable unused rto Clocks: disable unused mjcp davinci_emac_probe: using random MAC addr: 2a:b1:52:88:a2:88 emac-mii: probed eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, id=22161b) IP-Config: Complete: device=eth0, addr=192.168.1.228, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.228, domain=, nis-domain=(none), bootserver=192.168.1.3, rootserver=192.168.1.3, rootpath= yaffs: dev is 32505859 name is "mtdblock3" rw yaffs: passed flags "" VFS: Mounted root (yaffs2 filesystem) on device 31:3. Freeing init memory: 132K INIT: version 2.86 booting PHY: 1:01 - Link is Up - 100/Full Please wait: booting... Starting udev udev: starting version 141 Remounting root file system... Caching udev devnodes Populating dev cachemv: cannot rename '/tmp/devices': No such file or directory NET: Registered protocol family 10 ALSA: Restoring mixer settings... Configuring network interfaces... done. Setting up IP spoofing protection: rp_filter. hwclock: can't open '/dev/misc/rtc': No such file or directory Fri Mar 25 01:27:00 UTC 2011 hwclock: can't open '/dev/misc/rtc': No such file or directory INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm365-evm ttyS0 Arago 2011.02 dm365-evm ttyS0 dm365-evm login: _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm365-evm ttyS0 Arago 2011.02 dm365-evm ttyS0 dm365-evm login: o Password: Login incorrect login: root root@dm365-evm:~# root@dm365-evm:~# root@dm365-evm:~# ls wlan0up.sh root@dm365-evm:~# cd .. root@dm365-evm:/home# ls root root@dm365-evm:/home# cd .. root@dm365-evm:/# ls bin etc linuxrc mnt srv usr boot home lost+found proc sys var dev lib media sbin tmp root@dm365-evm:/# root@dm365-evm:/# root@dm365-evm:/# reboot Broadcast message from root (ttyS0) (Fri Mar 25 01:29:50 2011): The system is going down for reboot NOW! INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signaStopping telnet daemon. Stopping system message bus: stopped process in pidfile '/var/run/dbus/pid' (pid 1395) dbus. Stopping thttpd. ALSA: Storing mixer settings... Deconfiguring network interfaces... cat: can't open '/var/run/udhcpc.eth0.pid': No such file or directory done. Stopping syslogd/klogd: stopped syslogd (pid 1406) stopped klogd (pid 1408) done Sending all processes the TERM signal... Sending all processes the KILL signal... hwclock: can't open '/dev/misc/rtc': No such file or directory Unmounting remote filesystems... Deactivating swap... Unmounting local filesystems... Rebooting... musb_platform_disable 155: dma still active Restarting system. DM36x initialization passed! TI UBL Version: 1.50 Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000019. DONE Jumping to entry point at 0x81080000. U-Boot 1.3.4 (May 22 2009 - 11:25:39) I2C: ready DRAM: 128 MB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Bad block table not found for chip 0 Bad block table not found for chip 0 Bad block table written to 0x3ffc0000, version 0x01 Bad block table written to 0x3ff80000, version 0x01 NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 2048 MiB In: serial Out: serial Err: serial EEPROM @ 0x50 read FAILED!!! Ethernet PHY: GENERIC @ 0x00 Hit any key to stop autoboot: 0 Loading from NAND 1GiB 3,3V 8-bit, offset 0x400000 Image Name: Linux-2.6.32.17-davinci1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2095864 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Linux-2.6.32.17-davinci1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2095864 Bytes = 2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................................... done, booting the kernel. Linux version 2.6.32.17-davinci1 (root@punuo-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #4 PREEMPT Fri Aug 17 17:28:45 CST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM36x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm36x_rev1.2 variant 0x8 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 17780 Kernel command line: mem=70M console=ttyS0,115200n8 root=/dev/mtdblock3 rw rootfstype=yaffs2 ip=192.168.1.228:192.168.1.3:192.168.1.1:255.255.255.0::eth0:off eth=00:40:01:2B:64:60 video=davincifb:vid0=OFF:vid1=OFF:osd0=720x576x16,4050K dm365_imp.oper_mode=0 davinci_capture.device_type=1 davinci_enc_mngr.ch0_mode=pal PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 70MB = 70MB total Memory: 66380KB available (3936K code, 389K data, 132K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 147.86 BogoMIPS (lpj=739328) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 8 gpio irqs NET: Registered protocol family 16 davinci_serial_init:97: failed to get UART2 clock EVM: HD imager video input bio: create slab at 0 DM365 IPIPE initialized in Continuous mode SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pca9543a_probe vpss vpss: dm365_vpss vpss probed vpss vpss: dm365_vpss vpss probe success dm365_afew_hw_init ch0 default output "COMPOSITE", mode "PAL" VPBE Encoder Initialized cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US LogicPD encoder initialized Switching to clocksource timer0_1 musb_hdrc: version 6.0, cppi-dma, host, debug=0 musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. msgmni has been set to 129 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) Console: switching to colour frame buffer device 90x36 davincifb davincifb.0: dm_osd0_fb: 720x576x16@0,0 with framebuffer size 4050KB davincifb davincifb.0: dm_vid0_fb: 0x0x16@0,0 with framebuffer size 1224KB davincifb davincifb.0: dm_osd1_fb: 720x576x4@0,0 with framebuffer size 810KB davincifb davincifb.0: dm_vid1_fb: 0x0x16@0,0 with framebuffer size 1224KB DM365 IPIPEIF probed imp serializer initialized davinci_previewer initialized davinci_resizer initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A console [ttyS0] enabled brd: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) spi_davinci spi_davinci.0: DaVinci SPI driver in EDMA mode Using RX channel = 17 , TX channel = 16 and event queue = 3 at25 spi0.0: 8 KByte at25640 eeprom, pagesize 32 spi_davinci spi_davinci.0: Controller at 0xfec66000 console [netcon0] enabled netconsole: network logging started Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest input: DM365 EVM Controls as /devices/platform/i2c_davinci.1/i2c-1/1-0025/input/input0 i2c /dev entries driver Linux video capture interface: v2.00 ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter) ths7303 1-002c: ths7303 write failed ths7303: probe of 1-002c failed with error -121 vpfe_init vpfe-capture: vpss clock vpss_master enabled vpfe-capture vpfe-capture: v4l2 device registered vpfe-capture vpfe-capture: video device registered EVM: switch to tvp5146 SD video input tvp514x 1-005d: tvp514x 1-005d decoder driver registered !! vpfe-capture vpfe-capture: v4l2 sub device tvp5146 registered EVM: switch to tvp7002 HD video input vpfe-capture vpfe-capture: v4l2 sub device tvp7002 register fails EVM: switch to tvp7002 HD video input ths7353 1-002e: chip found @ 0x5c (DaVinci I2C adapter) ths7353 1-002e: No platform data!! ths7353 1-002e: ths7353 write failed ths7353: probe of 1-002e failed with error -121 vpfe-capture vpfe-capture: v4l2 sub device ths7353 register fails vpfe_register_ccdc_device: DM365 ISIF DM365 ISIF is registered with vpfe. af major#: 252, minor# 0 AF Driver initialized aew major#: 251, minor# 0 AEW Driver initialized Trying to register davinci display video device. layer=c30fb400,layer->video_dev=c30fb570 Trying to register davinci display video device. layer=c30fb800,layer->video_dev=c30fb970 davinci_init:DaVinci V4L2 Display Driver V1.0 loaded watchdog watchdog: heartbeat 60 sec davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x No device for DAI davinci-i2s asoc: tlv320aic3x <-> davinci-i2s mapping ok ALSA device list: #0: DaVinci EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 lib80211: common routines for IEEE802.11 drivers Clocks: disable unused mmcsd1 Clocks: disable unused spi1 Clocks: disable unused spi2 Clocks: disable unused spi3 Clocks: disable unused spi4 Clocks: disable unused pwm0 Clocks: disable unused pwm1 Clocks: disable unused pwm2 Clocks: disable unused pwm3 Clocks: disable unused timer1 Clocks: disable unused timer3 Clocks: disable unused emac Clocks: disable unused voice_codec Clocks: disable unused rto Clocks: disable unused mjcp davinci_emac_probe: using random MAC addr: f6:fe:4c:25:37:0a emac-mii: probed eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, id=22161b) IP-Config: Complete: device=eth0, addr=192.168.1.228, mask=255.255.255.0, gw=192.168.1.1, host=192.168.1.228, domain=, nis-domain=(none), bootserver=192.168.1.3, rootserver=192.168.1.3, rootpath= Looking up port of RPC 100003/2 on 192.168.1.3 PHY: 1:01 - Link is Up - 100/Full Looking up port of RPC 100005/1 on 192.168.1.3 Root-NFS: Server returned error -13 while mounting /tftpboot/192.168.1.228 VFS: Unable to mount root fs via NFS, trying floppy. VFS: Cannot open root device "mtdblock3" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) Backtrace: [] (dump_backtrace+0x0/0x114) from [] (dump_stack+0x18/0x1c) r7:00008000 r6:c3012000 r5:c0025808 r4:c04333d0 [] (dump_stack+0x0/0x1c) from [] (panic+0x54/0x12c) [] (panic+0x0/0x12c) from [] (mount_block_root+0x1e0/0x220) r3:00000001 r2:c3027e98 r1:c3027f60 r0:c039c256 [] (mount_block_root+0x0/0x220) from [] (mount_root+0xc4/0xfc) r8:00000000 r7:00000000 r6:00000000 r5:00000000 r4:00200000 [] (mount_root+0x0/0xfc) from [] (prepare_namespace+0x170/0x1c8) r5:c0025808 r4:c0432ee0 [] (prepare_namespace+0x0/0x1c8) from [] (kernel_init+0xe4/0x118) r5:00000000 r4:c0432ca0 [] (kernel_init+0x0/0x118) from [] (do_exit+0x0/0x668) r5:00000000 r4:00000000