CCCCCCCC U-Boot SPL 2013.01.01 (Jun 25 2013 - 16:42:52) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01.01 (Jun 25 2013 - 16:42:52) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: cpsw, usb_ether Hit any key to stop autoboot: 1  0 mmc0 is current device SD/MMC found on device 0 reading uEnv.txt ** Unable to read file uEnv.txt ** reading uImage 3194672 bytes read in 358 ms (8.5 MiB/s) Booting from mmc ... ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3194608 Bytes = 3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0 (mike@mike-VirtualBox) (gcc version 4.7.3 201 30226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Thu Feb 20 07:57:35 EST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] Machine: am335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 r w rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 513168k/513168k available, 11120k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0598000 (5696 kB) [ 0.000000] .init : 0xc0598000 - 0xc05d3000 ( 236 kB) [ 0.000000] .data : 0xc05d4000 - 0xc063e470 ( 426 kB) [ 0.000000] .bss : 0xc063e494 - 0xc066d2a4 ( 188 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrup ts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13 1071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.058929] pid_max: default: 32768 minimum: 301 [ 0.059082] Security Framework initialized [ 0.059173] Mount-cache hash table entries: 512 [ 0.059539] CPU: Testing write buffer coherency: ok [ 0.080047] omap_hwmod: pruss: failed to hardreset [ 0.081207] print_constraints: dummy: [ 0.081573] NET: Registered protocol family 16 [ 0.083709] OMAP GPIO hardware version 0.1 [ 0.086303] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.088226] omap_i2c.1: alias fck already exists [ 0.089172] omap2_mcspi.1: alias fck already exists [ 0.089385] omap2_mcspi.2: alias fck already exists [ 0.090332] edma.0: alias fck already exists [ 0.090362] edma.0: alias fck already exists [ 0.090362] edma.0: alias fck already exists [ 0.117004] bio: create slab at 0 [ 0.119262] SCSI subsystem initialized [ 0.120880] usbcore: registered new interface driver usbfs [ 0.121185] usbcore: registered new interface driver hub [ 0.121398] usbcore: registered new device driver usb [ 0.121704] registerd cppi-dma Intr @ IRQ 17 [ 0.121704] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000) [ 0.121704] Cppi41 Init Done [ 0.121734] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 [ 0.122039] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 [ 0.123168] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.125000] tps65910 1-002d: JTAGREVNUM 0x0 [ 0.127380] print_constraints: VRTC: [ 0.128845] print_constraints: VIO: at 1800 mV [ 0.131195] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.133483] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.134490] print_constraints: VDD3: 5000 mV [ 0.135894] print_constraints: VDIG1: at 1800 mV [ 0.137329] print_constraints: VDIG2: at 1800 mV [ 0.138732] print_constraints: VPLL: at 1800 mV [ 0.140197] print_constraints: VDAC: at 1800 mV [ 0.141601] print_constraints: VAUX1: at 1800 mV [ 0.143035] print_constraints: VAUX2: at 3300 mV [ 0.144470] print_constraints: VAUX33: at 3300 mV [ 0.145874] print_constraints: VMMC: at 3300 mV [ 0.146362] tps65910 1-002d: No interrupt support, no core IRQ [ 0.147766] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.148956] Switching to clocksource gp timer [ 0.164306] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.164489] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 [ 0.164825] MUSB0 controller's USBSS revision = 4ea20800 [ 0.165771] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18 [ 0.165924] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 [ 0.166229] MUSB1 controller's USBSS revision = 4ea20800 [ 0.166687] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.166778] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus numbe r 1 [ 0.166931] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.166931] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.166961] usb usb1: Product: MUSB HDRC host driver [ 0.166961] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd [ 0.166961] usb usb1: SerialNumber: musb-hdrc.1 [ 0.167785] hub 1-0:1.0: USB hub found [ 0.167816] hub 1-0:1.0: 1 port detected [ 0.168365] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19 [ 0.168792] NET: Registered protocol family 2 [ 0.168975] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.169403] TCP established hash table entries: 16384 (order: 5, 131072 bytes ) [ 0.169677] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.169860] TCP: Hash tables configured (established 16384 bind 16384) [ 0.169860] TCP reno registered [ 0.169891] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.169891] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.170104] NET: Registered protocol family 1 [ 0.170379] RPC: Registered named UNIX socket transport module. [ 0.170379] RPC: Registered udp transport module. [ 0.170379] RPC: Registered tcp transport module. [ 0.170410] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.170654] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.191741] VFS: Disk quotas dquot_6.5.2 [ 0.191833] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.192382] msgmni has been set to 1002 [ 0.195587] alg: No test for stdrng (krng) [ 0.196289] io scheduler noop registered [ 0.196289] io scheduler deadline registered [ 0.196350] io scheduler cfq registered (default) [ 0.200073] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.838012] console [ttyO0] enabled [ 0.842315] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 0.850158] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 0.857910] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.865692] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 0.873474] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 0.881713] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00 [ 0.898040] brd: module loaded [ 0.906127] loop: module loaded [ 0.909637] i2c-core: driver [tsl2550] using legacy suspend method [ 0.916076] i2c-core: driver [tsl2550] using legacy resume method [ 0.922515] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.936431] Detected a daughter card on AM335x EVM.. [ 0.941436] CPLD version: CPLD1.0F [ 0.945312] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.960479] Board name: A33515BB [ 0.963836] Board version: 1.4A [ 0.967102] SKU: SKU#01 [ 0.970214] The board is general purpose EVM in profile 0 [ 0.976898] da8xx_lcdc.0: alias fck already exists [ 0.982452] da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel [ 1.006530] Console: switching to colour frame buffer device 100x30 [ 1.022796] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.027801] Registering NAND on CS0 [ 1.032226] omap_i2c.2: alias fck already exists [ 1.037506] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 1.044158] tsl2550 2-0039: standard operating mode [ 1.049957] tsl2550 2-0039: support ver. 1.2 enabled [ 1.055786] davinci-mcasp.1: alias fck already exists [ 1.061676] omap_hsmmc.0: alias fck already exists [ 1.067077] omap_hsmmc.2: alias fck already exists [ 1.072509] Configure Bluetooth Enable pin... [ 1.080291] registered am33xx_sr device [ 1.084533] _regulator_get: 2-0018 supply Vdd not found, using dummy regulato r [ 1.092163] _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regul ator [ 1.120544] lis3lv02d: 8 bits 3DLH sensor found [ 1.210021] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d /input/input0 [ 1.221893] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.229187] omap2-nand driver initializing [ 1.233856] ONFI flash detected [ 1.237243] ONFI param page 0 valid [ 1.240905] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G 08ABAEAWP) [ 1.249481] Creating 8 MTD partitions on "omap2-nand.0": [ 1.255065] 0x000000000000-0x000000020000 : "SPL" [ 1.261444] 0x000000020000-0x000000040000 : "SPL.backup1" [ 1.268310] 0x000000040000-0x000000060000 : "SPL.backup2" [ 1.275238] 0x000000060000-0x000000080000 : "SPL.backup3" [ 1.282165] 0x000000080000-0x000000260000 : "U-Boot" [ 1.289367] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.296264] 0x000000280000-0x000000780000 : "Kernel" [ 1.304809] 0x000000780000-0x000010000000 : "File System" [ 1.414947] OneNAND driver initializing [ 1.420410] CAN device driver interface [ 1.424407] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.479614] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.486053] davinci_mdio davinci_mdio.0: detected phy mask fffffffe [ 1.493499] davinci_mdio.0: probed [ 1.497070] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown [ 1.504791] usbcore: registered new interface driver zd1201 [ 1.510803] usbcore: registered new interface driver cdc_ether [ 1.517059] usbcore: registered new interface driver cdc_eem [ 1.523132] usbcore: registered new interface driver dm9601 [ 1.528991] cdc_ncm: 04-Aug-2011 [ 1.532531] usbcore: registered new interface driver cdc_ncm [ 1.538452] Initializing USB Mass Storage driver... [ 1.543762] usbcore: registered new interface driver usb-storage [ 1.550048] USB Mass Storage support registered. [ 1.555297] mousedev: PS/2 mouse device common for all mice [ 1.562133] input: matrix-keypad as /devices/platform/matrix-keypad/input/inp ut1 [ 1.571105] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input 2 [ 1.579711] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0 [ 1.586914] i2c /dev entries driver [ 1.591278] Linux video capture interface: v2.00 [ 1.596405] usbcore: registered new interface driver uvcvideo [ 1.602447] USB Video Class driver (1.1.1) [ 1.607604] lm75 2-0048: hwmon0: sensor 'tmp275' [ 1.730529] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.739074] cpuidle: using governor ladder [ 1.743896] cpuidle: using governor menu [ 1.751861] omap4_aes_mod_init: loading AM33X AES driver [ 1.757537] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02 [ 1.764099] omap4_aes_probe: probe() done [ 1.768493] omap4_sham_mod_init: loading AM33X SHA/MD5 driver [ 1.774688] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03 [ 1.786407] omap4_sham_probe: probe() done [ 1.793273] usbcore: registered new interface driver usbhid [ 1.799133] usbhid: USB HID core driver [ 1.803863] tiadc tiadc: attached adc driver [ 1.812255] usbcore: registered new interface driver snd-usb-audio [ 1.820953] _regulator_get: 2-001b supply IOVDD not found, using dummy regula tor [ 1.828765] _regulator_get: 2-001b supply DVDD not found, using dummy regulat or [ 1.836486] _regulator_get: 2-001b supply AVDD not found, using dummy regulat or [ 1.844177] _regulator_get: 2-001b supply DRVDD not found, using dummy regula tor [ 1.854736] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok [ 1.865631] ALSA device list: [ 1.868743] #0: AM335X EVM [ 1.871795] oprofile: hardware counters not available [ 1.877044] oprofile: using timer interrupt. [ 1.881530] nf_conntrack version 0.5.0 (8018 buckets, 32072 max) [ 1.888397] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.894104] TCP cubic registered [ 1.897460] NET: Registered protocol family 17 [ 1.902130] can: controller area network core (rev 20090105 abi 8) [ 1.908691] NET: Registered protocol family 29 [ 1.913330] can: raw protocol (rev 20090105) [ 1.917785] can: broadcast manager protocol (rev 20090105 t) [ 1.923736] Registering the dns_resolver key type [ 1.928741] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.936767] ThumbEE CPU extension supported. [ 1.941314] mux: Failed to setup hwmod io irq -22 [ 1.946929] Power Management for AM33XX family [ 1.951812] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.958496] Copied the M3 firmware to UMEM [ 1.962860] Cortex M3 Firmware Version = 0x181 [ 1.967651] smartreflex smartreflex: am33xx_sr_probe: Zero NValue read from E FUSE [ 1.975524] smartreflex: probe of smartreflex failed with error -22 [ 1.982635] sr_init: platform driver register failed [ 1.993133] clock: disabling unused clocks to save power [ 2.011657] Detected MACID=0:18:31:8f:36:f0 [ 2.017181] cpsw: Detected MACID = 00:18:31:8f:36:f1 [ 2.024139] input: gpio-keys as /devices/platform/gpio-keys/input/input3 [ 2.031799] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.041229] Waiting for root device /dev/mmcblk0p2... [ 2.065307] mmc0: new high speed SDHC card at address e624 [ 2.071685] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 2.078582] mmcblk0: p1 p2 [ 2.164398] kjournald starting. Commit interval 5 seconds [ 2.194274] mmc1: card claims to support voltages below the defined range. Th ese will be ignored. [ 2.205535] EXT3-fs (mmcblk0p2): using internal journal [ 2.210998] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.218231] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.224945] Freeing init memory: 236K [ 2.237091] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.244110] mmc1: new SDIO card at address 0001 INIT: version 2.88 booting Starting udev [ 3.910461] Disabling lock debugging due to kernel taint [ 6.008392] cfg80211: Calling CRDA to update world regulatory domain [ 6.265014] wl12xx: driver version: ol_R5.SP4.01-dirty [ 6.270446] wl12xx: compilation time: Tue Jun 25 16:44:08 2013 [ 6.608428] cfg80211: World regulatory domain updated: [ 6.613891] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g ain, max_eirp) [ 6.622619] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.630889] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.639160] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.647460] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.655731] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.688415] wl12xx: loaded Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or d irectory bootlogd. ALSA: Restoring mixer settings... Configuring network interfaces... [ 7.709136] net eth0: CPSW phy found : id i s : 0x4dd074 ifconfig: bad address '192.168.xxx.xx' done. Wed Jun 26 00:02:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting telnet daemon. Performing wifi calibration... [ 8.862976] wl12xx: loaded [ 8.867034] wl12xx: power up [ 9.331634] wl12xx: firmware booted in PLT mode (PLT 6.3.10.0.135) Using nvs version 2.1 Calibrate /lib/firmware/ti-connectivity/wl1271-nvs.bin Writing calibration data to /lib/firmware/ti-connectivity/wl1271[ 9.405792] w l12xx: power down -nvs.bin Writing mac address 00:00:00:00:00:00 to file /lib/firmware/ti-connectivity/wl12 71-nvs.bin Calibration done. FEM1 has 1 bands. AutoFEM is off. Resulting nvs is /lib/firmwa re/ti-connectivity/wl1271-nvs.bin [ 10.053436] wl12xx: loaded Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Starting PVR Starting Lighttpd Web Server: lighttpd. 2013-06-26 00:02:02: (log.c.166) server started Starting UIM2 GUI application[ 11.399322] gadget: Mass Storage Function, vers ion: 2009/09/11 [ 11.405578] gadget: Number of LUNs=1 [ 11.409423] lun0: LUN: removable file: /dev/mmcblk0p1 [ 11.414825] gadget: Mass Storage Gadget, version: 2009/09/11 [ 11.420837] gadget: userspace failed to provide iSerialNumber [ 11.426940] gadget: g_mass_storage ready [ 11.431152] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 11.436767] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus numbe r 2 [ 11.444610] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.451721] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 11.459259] usb usb2: Product: MUSB HDRC host driver [ 11.464447] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd [ 11.469970] usb usb2: SerialNumber: musb-hdrc.0 [ 11.475250] hub 2-0:1.0: USB hub found [ 11.479187] hub 2-0:1.0: 1 port detected *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** Stopping Bootlog daemon: bootlogd. umount: can't umount /mnt/.psplash: Device or resource busy _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2013.05 am335x-evm ttyO0 am335x-evm login: root root@am335x-evm:~# cd /etc/init.d/ root@am335x-evm:/etc/init.d# ls 335x-demo inetd.busybox run-postinsts alignment.sh lighttpd save-rtc.sh alsa-state matrix-gui-2.0 sendsigs banner.sh modutils.sh single bootlogd mount-sdcard start-reset-daemon bootmisc.sh mountall.sh stop-bootlogd calibrate.sh mountnfs.sh storage-gadget-init checkroot.sh netperf sysfs.sh dbus-1 networking syslog devpts.sh parse-ip syslog.busybox dropbear populate-volatile.sh telnetd functions psplash.sh thttpd functions.initscripts pvr-init udev gplv3-notice rc uim2.sh halt rcS uim2.sh~ hostapd reboot umountfs hostname.sh resetd.sh umountnfs.sh hwclock.sh rmnologin.sh urandom root@am335x-evm:/etc/init.d# ./a 335x-demo 0x10205 debug8.x installing 8.x SGX debug user libraries ./335x-demo: line 17: cd: /opt/gfxlibraries/gfx_dbg_es8.x: No such file or direc tory ./335x-demo: line 18: ./install.sh: No such file or directory root@am335x-evm:/etc/init.d# ls /opt/gfxlibraries/ gfx_rel_es8.x root@am335x-evm:/etc/init.d# cd /opt/g  root@am335x-evm:/opt# ls gfx_dbg_es8.x gfxlibraries gfxsdkdemos ltp root@am335x-evm:/opt# sudo      mv gfx_dbg_es8.x/ gfxlibraries/ root@am335x-evm:/opt# ls gfxlibraries gfxsdkdemos ltp root@am335x-evm:/opt# ls gfxlibraries/ gfx_dbg_es8.x gfx_rel_es8.x root@am335x-evm:/opt# cd /etc/init.d root@am335x-evm:/etc/init.d# ./e 335x-demo 0x10205 debug8.x installing 8.x SGX debug user libraries Installing PowerVR Consumer/Embedded DDK 'sgxddk_1.10@2359475' on target File system installation root is / Nothing to un-install. boot script rc.pvr -> /etc/init.d/rc.pvr kernel module pvrsrvkm.ko -> /lib/modules/3.2.0/extra/pvrsrvkm.ko kernel module omaplfb.ko -> /lib/modules/3.2.0/extra/omaplfb.ko shared library libGLES_CM.so -> /usr/lib/libGLES_CM.so.1.10.2359475 shared library libusc.so -> /usr/lib/libusc.so.1.10.2359475 shared library libGLESv2.so -> /usr/lib/libGLESv2.so.1.10.2359475 shared library libglslcompiler.so -> /usr/lib/libglslcompiler.so.1.10.2359475 shared library libIMGegl.so -> /usr/lib/libIMGegl.so.1.10.2359475 shared library libEGL.so -> /usr/lib/libEGL.so.1.10.2359475 shared library libpvr2d.so -> /usr/lib/libpvr2d.so.1.10.2359475 shared library libpvrPVR2D_BLITWSEGL.so -> /usr/lib/libpvrPVR2D_BLITWSEGL.so.1.1 0.2359475 shared library libpvrPVR2D_FLIPWSEGL.so -> /usr/lib/libpvrPVR2D_FLIPWSEGL.so.1.1 0.2359475 shared library libpvrPVR2D_FRONTWSEGL.so -> /usr/lib/libpvrPVR2D_FRONTWSEGL.so.1 .10.2359475 shared library libpvrPVR2D_LINUXFBWSEGL.so -> /usr/lib/libpvrPVR2D_LINUXFBWSEGL. so.1.10.2359475 shared library libsrv_um.so -> /usr/lib/libsrv_um.so.1.10.2359475 shared library libsrv_init.so -> /usr/lib/libsrv_init.so.1.10.2359475 shared library libPVRScopeServices.so -> /usr/lib/libPVRScopeServices.so.1.10.23 59475 binary pvrsrvctl -> /usr/local/bin/pvrsrvctl binary sgx_init_test -> /usr/local/bin/sgx_init_test binary services_test -> /usr/local/bin/services_test binary sgx_blit_test -> /usr/local/bin/sgx_blit_test binary sgx_clipblit_test -> /usr/local/bin/sgx_clipblit_test binary sgx_flip_test -> /usr/local/bin/sgx_flip_test binary sgx_render_flip_test -> /usr/local/bin/sgx_render_flip_test binary pvr2d_test -> /usr/local/bin/pvr2d_test shader glsltest1_vertshader.txt -> /usr/local/bin/glsltest1_vertshader.txt shader glsltest1_fragshaderA.txt -> /usr/local/bin/glsltest1_fragshaderA.txt shader glsltest1_fragshaderB.txt -> /usr/local/bin/glsltest1_fragshaderB.txt Installation complete! You may now reboot your target. ./rc.pvr: line 34: /usr/local/bin/pvrsrvctl: No such file or directory root@am335x-evm:/etc/init.d# CCCCCCCC U-Boot SPL 2013.01.01 (Jun 25 2013 - 16:42:52) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01.01 (Jun 25 2013 - 16:42:52) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: cpsw, usb_ether Hit any key to stop autoboot: 1  0 mmc0 is current device SD/MMC found on device 0 reading uEnv.txt ** Unable to read file uEnv.txt ** reading uImage 3194672 bytes read in 357 ms (8.5 MiB/s) Booting from mmc ... ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3194608 Bytes = 3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0 (mike@mike-VirtualBox) (gcc version 4.7.3 201 30226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Thu Feb 20 07:57:35 EST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] Machine: am335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 r w rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 513168k/513168k available, 11120k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0598000 (5696 kB) [ 0.000000] .init : 0xc0598000 - 0xc05d3000 ( 236 kB) [ 0.000000] .data : 0xc05d4000 - 0xc063e470 ( 426 kB) [ 0.000000] .bss : 0xc063e494 - 0xc066d2a4 ( 188 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrup ts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13 1071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.058959] pid_max: default: 32768 minimum: 301 [ 0.059082] Security Framework initialized [ 0.059173] Mount-cache hash table entries: 512 [ 0.059539] CPU: Testing write buffer coherency: ok [ 0.080047] omap_hwmod: pruss: failed to hardreset [ 0.081207] print_constraints: dummy: [ 0.081573] NET: Registered protocol family 16 [ 0.083679] OMAP GPIO hardware version 0.1 [ 0.086242] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.088195] omap_i2c.1: alias fck already exists [ 0.089141] omap2_mcspi.1: alias fck already exists [ 0.089355] omap2_mcspi.2: alias fck already exists [ 0.090301] edma.0: alias fck already exists [ 0.090332] edma.0: alias fck already exists [ 0.090362] edma.0: alias fck already exists [ 0.117004] bio: create slab at 0 [ 0.119262] SCSI subsystem initialized [ 0.120880] usbcore: registered new interface driver usbfs [ 0.121185] usbcore: registered new interface driver hub [ 0.121398] usbcore: registered new device driver usb [ 0.121704] registerd cppi-dma Intr @ IRQ 17 [ 0.121704] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000) [ 0.121704] Cppi41 Init Done [ 0.121734] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 [ 0.122039] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 [ 0.123168] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.125000] tps65910 1-002d: JTAGREVNUM 0x0 [ 0.127410] print_constraints: VRTC: [ 0.128875] print_constraints: VIO: at 1800 mV [ 0.131225] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.133514] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.134490] print_constraints: VDD3: 5000 mV [ 0.135925] print_constraints: VDIG1: at 1800 mV [ 0.137329] print_constraints: VDIG2: at 1800 mV [ 0.138763] print_constraints: VPLL: at 1800 mV [ 0.140228] print_constraints: VDAC: at 1800 mV [ 0.141662] print_constraints: VAUX1: at 1800 mV [ 0.143096] print_constraints: VAUX2: at 3300 mV [ 0.144500] print_constraints: VAUX33: at 3300 mV [ 0.145904] print_constraints: VMMC: at 3300 mV [ 0.146423] tps65910 1-002d: No interrupt support, no core IRQ [ 0.147796] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.149017] Switching to clocksource gp timer [ 0.164367] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.164550] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 [ 0.164886] MUSB0 controller's USBSS revision = 4ea20800 [ 0.165863] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18 [ 0.166015] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 [ 0.166320] MUSB1 controller's USBSS revision = 4ea20800 [ 0.166778] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.166870] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus numbe r 1 [ 0.166992] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.167022] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.167022] usb usb1: Product: MUSB HDRC host driver [ 0.167022] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd [ 0.167053] usb usb1: SerialNumber: musb-hdrc.1 [ 0.167846] hub 1-0:1.0: USB hub found [ 0.167877] hub 1-0:1.0: 1 port detected [ 0.168457] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19 [ 0.168853] NET: Registered protocol family 2 [ 0.169128] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.169464] TCP established hash table entries: 16384 (order: 5, 131072 bytes ) [ 0.169738] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.169921] TCP: Hash tables configured (established 16384 bind 16384) [ 0.169921] TCP reno registered [ 0.169952] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.169952] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.170166] NET: Registered protocol family 1 [ 0.170440] RPC: Registered named UNIX socket transport module. [ 0.170440] RPC: Registered udp transport module. [ 0.170471] RPC: Registered tcp transport module. [ 0.170471] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.170715] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.191833] VFS: Disk quotas dquot_6.5.2 [ 0.191925] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.192443] msgmni has been set to 1002 [ 0.195678] alg: No test for stdrng (krng) [ 0.196350] io scheduler noop registered [ 0.196350] io scheduler deadline registered [ 0.196441] io scheduler cfq registered (default) [ 0.200164] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.838104] console [ttyO0] enabled [ 0.842407] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 0.850250] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 0.858001] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.865783] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 0.873596] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 0.881866] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00 [ 0.898193] brd: module loaded [ 0.906280] loop: module loaded [ 0.909790] i2c-core: driver [tsl2550] using legacy suspend method [ 0.916259] i2c-core: driver [tsl2550] using legacy resume method [ 0.922698] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.936614] Detected a daughter card on AM335x EVM.. [ 0.941619] CPLD version: CPLD1.0F [ 0.945465] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.960632] Board name: A33515BB [ 0.964019] Board version: 1.4A [ 0.967285] SKU: SKU#01 [ 0.970367] The board is general purpose EVM in profile 0 [ 0.977050] da8xx_lcdc.0: alias fck already exists [ 0.982604] da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel [ 1.006683] Console: switching to colour frame buffer device 100x30 [ 1.022949] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.027954] Registering NAND on CS0 [ 1.032348] omap_i2c.2: alias fck already exists [ 1.037628] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 1.044281] tsl2550 2-0039: standard operating mode [ 1.050079] tsl2550 2-0039: support ver. 1.2 enabled [ 1.055938] davinci-mcasp.1: alias fck already exists [ 1.061828] omap_hsmmc.0: alias fck already exists [ 1.067230] omap_hsmmc.2: alias fck already exists [ 1.072662] Configure Bluetooth Enable pin... [ 1.080444] registered am33xx_sr device [ 1.084686] _regulator_get: 2-0018 supply Vdd not found, using dummy regulato r [ 1.092315] _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regul ator [ 1.120758] lis3lv02d: 8 bits 3DLH sensor found [ 1.210052] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d /input/input0 [ 1.221923] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.229187] omap2-nand driver initializing [ 1.233856] ONFI flash detected [ 1.237243] ONFI param page 0 valid [ 1.240905] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G 08ABAEAWP) [ 1.249481] Creating 8 MTD partitions on "omap2-nand.0": [ 1.255065] 0x000000000000-0x000000020000 : "SPL" [ 1.261413] 0x000000020000-0x000000040000 : "SPL.backup1" [ 1.268280] 0x000000040000-0x000000060000 : "SPL.backup2" [ 1.275207] 0x000000060000-0x000000080000 : "SPL.backup3" [ 1.282135] 0x000000080000-0x000000260000 : "U-Boot" [ 1.289337] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.296203] 0x000000280000-0x000000780000 : "Kernel" [ 1.304718] 0x000000780000-0x000010000000 : "File System" [ 1.414825] OneNAND driver initializing [ 1.420318] CAN device driver interface [ 1.424316] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.479675] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.486145] davinci_mdio davinci_mdio.0: detected phy mask fffffffe [ 1.493591] davinci_mdio.0: probed [ 1.497161] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown [ 1.504882] usbcore: registered new interface driver zd1201 [ 1.510894] usbcore: registered new interface driver cdc_ether [ 1.517150] usbcore: registered new interface driver cdc_eem [ 1.523223] usbcore: registered new interface driver dm9601 [ 1.529083] cdc_ncm: 04-Aug-2011 [ 1.532592] usbcore: registered new interface driver cdc_ncm [ 1.538513] Initializing USB Mass Storage driver... [ 1.543823] usbcore: registered new interface driver usb-storage [ 1.550109] USB Mass Storage support registered. [ 1.555389] mousedev: PS/2 mouse device common for all mice [ 1.562225] input: matrix-keypad as /devices/platform/matrix-keypad/input/inp ut1 [ 1.571197] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input 2 [ 1.579803] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0 [ 1.586975] i2c /dev entries driver [ 1.591339] Linux video capture interface: v2.00 [ 1.596496] usbcore: registered new interface driver uvcvideo [ 1.602508] USB Video Class driver (1.1.1) [ 1.607696] lm75 2-0048: hwmon0: sensor 'tmp275' [ 1.710571] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.719116] cpuidle: using governor ladder [ 1.723937] cpuidle: using governor menu [ 1.731903] omap4_aes_mod_init: loading AM33X AES driver [ 1.737579] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02 [ 1.744140] omap4_aes_probe: probe() done [ 1.748565] omap4_sham_mod_init: loading AM33X SHA/MD5 driver [ 1.754760] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03 [ 1.766510] omap4_sham_probe: probe() done [ 1.773345] usbcore: registered new interface driver usbhid [ 1.779144] usbhid: USB HID core driver [ 1.783905] tiadc tiadc: attached adc driver [ 1.792358] usbcore: registered new interface driver snd-usb-audio [ 1.801086] _regulator_get: 2-001b supply IOVDD not found, using dummy regula tor [ 1.808898] _regulator_get: 2-001b supply DVDD not found, using dummy regulat or [ 1.816619] _regulator_get: 2-001b supply AVDD not found, using dummy regulat or [ 1.824310] _regulator_get: 2-001b supply DRVDD not found, using dummy regula tor [ 1.834930] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok [ 1.842742] ALSA device list: [ 1.845855] #0: AM335X EVM [ 1.848846] oprofile: hardware counters not available [ 1.854156] oprofile: using timer interrupt. [ 1.858642] nf_conntrack version 0.5.0 (8018 buckets, 32072 max) [ 1.865478] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.871185] TCP cubic registered [ 1.874572] NET: Registered protocol family 17 [ 1.879211] can: controller area network core (rev 20090105 abi 8) [ 1.885772] NET: Registered protocol family 29 [ 1.890411] can: raw protocol (rev 20090105) [ 1.894866] can: broadcast manager protocol (rev 20090105 t) [ 1.900848] Registering the dns_resolver key type [ 1.905822] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.913848] ThumbEE CPU extension supported. [ 1.918365] mux: Failed to setup hwmod io irq -22 [ 1.923980] Power Management for AM33XX family [ 1.928863] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.935546] Copied the M3 firmware to UMEM [ 1.939910] Cortex M3 Firmware Version = 0x181 [ 1.944732] smartreflex smartreflex: am33xx_sr_probe: Zero NValue read from E FUSE [ 1.952575] smartreflex: probe of smartreflex failed with error -22 [ 1.962738] sr_init: platform driver register failed [ 1.973236] clock: disabling unused clocks to save power [ 1.991851] Detected MACID=0:18:31:8f:36:f0 [ 1.997344] cpsw: Detected MACID = 00:18:31:8f:36:f1 [ 2.004333] input: gpio-keys as /devices/platform/gpio-keys/input/input3 [ 2.011993] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.021392] Waiting for root device /dev/mmcblk0p2... [ 2.045440] mmc0: new high speed SDHC card at address e624 [ 2.051849] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 2.058715] mmcblk0: p1 p2 [ 2.174621] mmc1: card claims to support voltages below the defined range. Th ese will be ignored. [ 2.198394] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.207122] mmc1: new SDIO card at address 0001 [ 4.754821] kjournald starting. Commit interval 5 seconds [ 4.763610] EXT3-fs (mmcblk0p2): using internal journal [ 4.771057] EXT3-fs (mmcblk0p2): 1 orphan inode deleted [ 4.776489] EXT3-fs (mmcblk0p2): recovery complete [ 4.813568] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 4.820831] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 4.827545] Freeing init memory: 236K INIT: version 2.88 booting Starting udev [ 6.543975] Disabling lock debugging due to kernel taint [ 8.658020] cfg80211: Calling CRDA to update world regulatory domain [ 8.869689] cfg80211: World regulatory domain updated: [ 8.875183] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g ain, max_eirp) [ 8.883911] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.892181] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.900451] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.908691] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.916961] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.956604] wl12xx: driver version: ol_R5.SP4.01-dirty [ 8.962036] wl12xx: compilation time: Tue Jun 25 16:44:08 2013 [ 9.460083] wl12xx: loaded Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or d irectory bootlogd. ALSA: Restoring mixer settings... Configuring network interfaces... [ 10.509063] net eth0: CPSW phy found : id i s : 0x4dd074 ifconfig: bad address '192.168.xxx.xx' done. Wed Jun 26 00:02:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting telnet daemon. Performing wifi calibration... [ 11.673217] wl12xx: loaded [ 11.677307] wl12xx: power up [ 12.141693] wl12xx: firmware booted in PLT mode (PLT 6.3.10.0.135) Using nvs version 2.1 Calibrate /lib/firmware/ti-connectivity/wl1271-nvs.bin Writing calibration data to /lib/firmware/ti-connectivity/wl1271[ 12.215972] w l12xx: power down -nvs.bin Writing mac address 00:00:00:00:00:00 to file /lib/firmware/ti-connectivity/wl12 71-nvs.bin Calibration done. FEM1 has 1 bands. AutoFEM is off. Resulting nvs is /lib/firmwa re/ti-connectivity/wl1271-nvs.bin [ 12.863098] wl12xx: loaded Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Starting PVR [ 13.455261] pvrsrvkm: Unknown parameter `/lib/modules/3.2.0/kernel/drivers/gp u/pvr/pvrsrvkm.ko' Error: could not insert module /lib/modules/3.2.0/extra/pvrsrvkm.ko: Unknown sym bol in module Could not find pvrsrvkm driver Starting Lighttpd Web Server: lighttpd. 2013-06-26 00:02:02: (log.c.166) server started Starting UIM2 GUI application[ 14.119476] gadget: Mass Storage Function, vers ion: 2009/09/11 [ 14.125762] gadget: Number of LUNs=1 [ 14.129577] lun0: LUN: removable file: /dev/mmcblk0p1 [ 14.134979] gadget: Mass Storage Gadget, version: 2009/09/11 [ 14.140991] gadget: userspace failed to provide iSerialNumber [ 14.147094] gadget: g_mass_storage ready [ 14.151306] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 14.156921] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus numbe r 2 [ 14.164764] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 14.171875] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 14.179412] usb usb2: Product: MUSB HDRC host driver [ 14.184600] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd [ 14.190155] usb usb2: SerialNumber: musb-hdrc.0 [ 14.195465] hub 2-0:1.0: USB hub found [ 14.199401] hub 2-0:1.0: 1 port detected *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** Stopping Bootlog daemon: bootlogd. umount: can't umount /mnt/.psplash: Device or resource busy _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2013.05 am335x-evm ttyO0 am335x-evm login: root root@am335x-evm:~# cd    wd  pwd /home/root root@am335x-evm:~# ls Settings a.out idfile latform root@am335x-evm:~# cd .. root@am335x-evm:/home# ls Emerson_Network_Power_strip.bmp gfx_check.sh bin root root@am335x-evm:/home# ./gfx_check.sh WSEGL settings [default] WindowSystem=libpvrPVR2D_FRONTWSEGL.so.1 ------ ARM CPU information Processor : ARMv7 Processor rev 2 (v7l) BogoMIPS : 718.02 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x3 CPU part : 0xc08 CPU revision : 2 Hardware : am335xevm Revision : 0000 Serial : 0000000000000000 ------ SGX driver information cat: can't open '/proc/pvr/version': No such file or directory ------ Framebuffer settings mode "800x480-62" # D: 30.000 MHz, H: 32.433 kHz, V: 61.895 Hz geometry 800 480 800 960 32 timings 33333 39 39 29 13 47 2 rgba 8/16,8/8,8/0,8/24 endmode Frame buffer device information: Name : DA8xx FB Drv Address : 0x9f400000 Size : 3072000 Type : PACKED PIXELS Visual : TRUECOLOR XPanStep : 0 YPanStep : 1 YWrapStep : 0 LineLength : 3200 Accelerator : No ------ Rotation settings 0 ------ Kernel Module information Module Size Used by g_mass_storage 37599 0 wl12xx_sdio 3986 0 wl12xx 202633 0 mac80211 289010 1 wl12xx cfg80211 189234 2 mac80211,wl12xx ------ Boot settings console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none ------ Linux Kernel version Linux am335x-evm 3.2.0 #1 Thu Feb 20 07:57:35 EST 2014 armv7l GNU/Linux root@am335x-evm:/home# ls /    cd /opt/ root@am335x-evm:/opt# ls gfxlibraries gfxsdkdemos ltp root@am335x-evm:/opt# cd gfxdem         home    depmod -a root@am335x-evm:/opt# CCCCCCCC U-Boot SPL 2013.01.01 (Jun 25 2013 - 16:42:52) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01.01 (Jun 25 2013 - 16:42:52) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: cpsw, usb_ether Hit any key to stop autoboot: 1  0 mmc0 is current device SD/MMC found on device 0 reading uEnv.txt ** Unable to read file uEnv.txt ** reading uImage 3194672 bytes read in 358 ms (8.5 MiB/s) Booting from mmc ... ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3194608 Bytes = 3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0 (mike@mike-VirtualBox) (gcc version 4.7.3 201 30226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Thu Feb 20 07:57:35 EST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] Machine: am335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 r w rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 513168k/513168k available, 11120k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0598000 (5696 kB) [ 0.000000] .init : 0xc0598000 - 0xc05d3000 ( 236 kB) [ 0.000000] .data : 0xc05d4000 - 0xc063e470 ( 426 kB) [ 0.000000] .bss : 0xc063e494 - 0xc066d2a4 ( 188 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrup ts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13 1071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.058929] pid_max: default: 32768 minimum: 301 [ 0.059051] Security Framework initialized [ 0.059173] Mount-cache hash table entries: 512 [ 0.059539] CPU: Testing write buffer coherency: ok [ 0.080047] omap_hwmod: pruss: failed to hardreset [ 0.081176] print_constraints: dummy: [ 0.081542] NET: Registered protocol family 16 [ 0.083709] OMAP GPIO hardware version 0.1 [ 0.086242] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.088195] omap_i2c.1: alias fck already exists [ 0.089111] omap2_mcspi.1: alias fck already exists [ 0.089355] omap2_mcspi.2: alias fck already exists [ 0.090301] edma.0: alias fck already exists [ 0.090332] edma.0: alias fck already exists [ 0.090332] edma.0: alias fck already exists [ 0.117034] bio: create slab at 0 [ 0.119293] SCSI subsystem initialized [ 0.120880] usbcore: registered new interface driver usbfs [ 0.121185] usbcore: registered new interface driver hub [ 0.121368] usbcore: registered new device driver usb [ 0.121673] registerd cppi-dma Intr @ IRQ 17 [ 0.121704] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000) [ 0.121704] Cppi41 Init Done [ 0.121734] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 [ 0.122039] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 [ 0.123168] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.125000] tps65910 1-002d: JTAGREVNUM 0x0 [ 0.127410] print_constraints: VRTC: [ 0.128845] print_constraints: VIO: at 1800 mV [ 0.131195] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.133483] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.134490] print_constraints: VDD3: 5000 mV [ 0.135894] print_constraints: VDIG1: at 1800 mV [ 0.137329] print_constraints: VDIG2: at 1800 mV [ 0.138732] print_constraints: VPLL: at 1800 mV [ 0.140197] print_constraints: VDAC: at 1800 mV [ 0.141632] print_constraints: VAUX1: at 1800 mV [ 0.143066] print_constraints: VAUX2: at 3300 mV [ 0.144470] print_constraints: VAUX33: at 3300 mV [ 0.145874] print_constraints: VMMC: at 3300 mV [ 0.146392] tps65910 1-002d: No interrupt support, no core IRQ [ 0.147766] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.148986] Switching to clocksource gp timer [ 0.164276] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.164489] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 [ 0.164825] MUSB0 controller's USBSS revision = 4ea20800 [ 0.165771] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18 [ 0.165924] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 [ 0.166229] MUSB1 controller's USBSS revision = 4ea20800 [ 0.166717] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.166778] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus numbe r 1 [ 0.166931] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.166931] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.166961] usb usb1: Product: MUSB HDRC host driver [ 0.166961] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd [ 0.166961] usb usb1: SerialNumber: musb-hdrc.1 [ 0.167785] hub 1-0:1.0: USB hub found [ 0.167816] hub 1-0:1.0: 1 port detected [ 0.168365] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19 [ 0.168792] NET: Registered protocol family 2 [ 0.169067] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.169403] TCP established hash table entries: 16384 (order: 5, 131072 bytes ) [ 0.169677] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.169860] TCP: Hash tables configured (established 16384 bind 16384) [ 0.169860] TCP reno registered [ 0.169891] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.169921] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.170104] NET: Registered protocol family 1 [ 0.170379] RPC: Registered named UNIX socket transport module. [ 0.170379] RPC: Registered udp transport module. [ 0.170379] RPC: Registered tcp transport module. [ 0.170410] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.170654] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.191772] VFS: Disk quotas dquot_6.5.2 [ 0.191864] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.192413] msgmni has been set to 1002 [ 0.195587] alg: No test for stdrng (krng) [ 0.196289] io scheduler noop registered [ 0.196289] io scheduler deadline registered [ 0.196380] io scheduler cfq registered (default) [ 0.200073] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.837921] console [ttyO0] enabled [ 0.842224] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 0.850067] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 0.857818] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.865600] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 0.873382] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 0.881652] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00 [ 0.897979] brd: module loaded [ 0.906036] loop: module loaded [ 0.909484] i2c-core: driver [tsl2550] using legacy suspend method [ 0.915985] i2c-core: driver [tsl2550] using legacy resume method [ 0.922424] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.936340] Detected a daughter card on AM335x EVM.. [ 0.941345] CPLD version: CPLD1.0F [ 0.945190] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 0.960357] Board name: A33515BB [ 0.963745] Board version: 1.4A [ 0.967010] SKU: SKU#01 [ 0.970092] The board is general purpose EVM in profile 0 [ 0.976776] da8xx_lcdc.0: alias fck already exists [ 0.982330] da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel [ 1.006408] Console: switching to colour frame buffer device 100x30 [ 1.022674] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.027679] Registering NAND on CS0 [ 1.032073] omap_i2c.2: alias fck already exists [ 1.037353] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 1.044006] tsl2550 2-0039: standard operating mode [ 1.049804] tsl2550 2-0039: support ver. 1.2 enabled [ 1.055664] davinci-mcasp.1: alias fck already exists [ 1.061553] omap_hsmmc.0: alias fck already exists [ 1.066925] omap_hsmmc.2: alias fck already exists [ 1.072357] Configure Bluetooth Enable pin... [ 1.080139] registered am33xx_sr device [ 1.084381] _regulator_get: 2-0018 supply Vdd not found, using dummy regulato r [ 1.092010] _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regul ator [ 1.120422] lis3lv02d: 8 bits 3DLH sensor found [ 1.210021] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d /input/input0 [ 1.221893] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.229187] omap2-nand driver initializing [ 1.233825] ONFI flash detected [ 1.237213] ONFI param page 0 valid [ 1.240875] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G 08ABAEAWP) [ 1.249450] Creating 8 MTD partitions on "omap2-nand.0": [ 1.255035] 0x000000000000-0x000000020000 : "SPL" [ 1.261383] 0x000000020000-0x000000040000 : "SPL.backup1" [ 1.268280] 0x000000040000-0x000000060000 : "SPL.backup2" [ 1.275207] 0x000000060000-0x000000080000 : "SPL.backup3" [ 1.282135] 0x000000080000-0x000000260000 : "U-Boot" [ 1.289337] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.296203] 0x000000280000-0x000000780000 : "Kernel" [ 1.304718] 0x000000780000-0x000010000000 : "File System" [ 1.414825] OneNAND driver initializing [ 1.420318] CAN device driver interface [ 1.424316] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.479614] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.486053] davinci_mdio davinci_mdio.0: detected phy mask fffffffe [ 1.493499] davinci_mdio.0: probed [ 1.497039] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown [ 1.504791] usbcore: registered new interface driver zd1201 [ 1.510803] usbcore: registered new interface driver cdc_ether [ 1.517028] usbcore: registered new interface driver cdc_eem [ 1.523132] usbcore: registered new interface driver dm9601 [ 1.528991] cdc_ncm: 04-Aug-2011 [ 1.532531] usbcore: registered new interface driver cdc_ncm [ 1.538421] Initializing USB Mass Storage driver... [ 1.543731] usbcore: registered new interface driver usb-storage [ 1.550018] USB Mass Storage support registered. [ 1.555297] mousedev: PS/2 mouse device common for all mice [ 1.562103] input: matrix-keypad as /devices/platform/matrix-keypad/input/inp ut1 [ 1.571105] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input 2 [ 1.579711] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0 [ 1.586883] i2c /dev entries driver [ 1.591217] Linux video capture interface: v2.00 [ 1.596374] usbcore: registered new interface driver uvcvideo [ 1.602386] USB Video Class driver (1.1.1) [ 1.607574] lm75 2-0048: hwmon0: sensor 'tmp275' [ 1.710510] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.719055] cpuidle: using governor ladder [ 1.723846] cpuidle: using governor menu [ 1.731811] omap4_aes_mod_init: loading AM33X AES driver [ 1.737457] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02 [ 1.744049] omap4_aes_probe: probe() done [ 1.748474] omap4_sham_mod_init: loading AM33X SHA/MD5 driver [ 1.754638] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03 [ 1.766387] omap4_sham_probe: probe() done [ 1.773193] usbcore: registered new interface driver usbhid [ 1.778991] usbhid: USB HID core driver [ 1.783752] tiadc tiadc: attached adc driver [ 1.792175] usbcore: registered new interface driver snd-usb-audio [ 1.800933] _regulator_get: 2-001b supply IOVDD not found, using dummy regula tor [ 1.808746] _regulator_get: 2-001b supply DVDD not found, using dummy regulat or [ 1.816467] _regulator_get: 2-001b supply AVDD not found, using dummy regulat or [ 1.824127] _regulator_get: 2-001b supply DRVDD not found, using dummy regula tor [ 1.834747] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok [ 1.842529] ALSA device list: [ 1.845642] #0: AM335X EVM [ 1.848632] oprofile: hardware counters not available [ 1.853942] oprofile: using timer interrupt. [ 1.858428] nf_conntrack version 0.5.0 (8018 buckets, 32072 max) [ 1.865295] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.870971] TCP cubic registered [ 1.874359] NET: Registered protocol family 17 [ 1.878997] can: controller area network core (rev 20090105 abi 8) [ 1.885559] NET: Registered protocol family 29 [ 1.890197] can: raw protocol (rev 20090105) [ 1.894653] can: broadcast manager protocol (rev 20090105 t) [ 1.900604] Registering the dns_resolver key type [ 1.905609] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.913635] ThumbEE CPU extension supported. [ 1.918151] mux: Failed to setup hwmod io irq -22 [ 1.923767] Power Management for AM33XX family [ 1.928649] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.935333] Copied the M3 firmware to UMEM [ 1.939697] Cortex M3 Firmware Version = 0x181 [ 1.944488] smartreflex smartreflex: am33xx_sr_probe: Zero NValue read from E FUSE [ 1.952331] smartreflex: probe of smartreflex failed with error -22 [ 1.962493] sr_init: platform driver register failed [ 1.972991] clock: disabling unused clocks to save power [ 1.991577] Detected MACID=0:18:31:8f:36:f0 [ 1.997100] cpsw: Detected MACID = 00:18:31:8f:36:f1 [ 2.004028] input: gpio-keys as /devices/platform/gpio-keys/input/input3 [ 2.011718] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.021118] Waiting for root device /dev/mmcblk0p2... [ 2.045166] mmc0: new high speed SDHC card at address e624 [ 2.051574] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 2.058410] mmcblk0: p1 p2 [ 2.174285] mmc1: card claims to support voltages below the defined range. Th ese will be ignored. [ 2.193359] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.200134] mmc1: new SDIO card at address 0001 [ 2.372436] kjournald starting. Commit interval 5 seconds [ 2.381134] EXT3-fs (mmcblk0p2): using internal journal [ 2.386596] EXT3-fs (mmcblk0p2): recovery complete [ 2.394165] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.401428] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.408111] Freeing init memory: 236K INIT: version 2.88 booting Starting udev [ 4.043701] Disabling lock debugging due to kernel taint [ 6.122314] cfg80211: Calling CRDA to update world regulatory domain [ 6.377502] wl12xx: driver version: ol_R5.SP4.01-dirty [ 6.382904] wl12xx: compilation time: Tue Jun 25 16:44:08 2013 [ 6.714202] cfg80211: World regulatory domain updated: [ 6.719573] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g ain, max_eirp) [ 6.728363] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.736633] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.744934] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.753204] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.761474] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.792175] wl12xx: loaded Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or d irectory bootlogd. ALSA: Restoring mixer settings... Configuring network interfaces... [ 7.710327] net eth0: CPSW phy found : id i s : 0x4dd074 ifconfig: bad address '192.168.xxx.xx' done. Wed Jun 26 00:02:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting telnet daemon. Performing wifi calibration... [ 8.863037] wl12xx: loaded [ 8.867095] wl12xx: power up [ 9.331634] wl12xx: firmware booted in PLT mode (PLT 6.3.10.0.135) Using nvs version 2.1 Calibrate /lib/firmware/ti-connectivity/wl1271-nvs.bin Writing calibration data to /lib/firmware/ti-connectivity/wl1271[ 9.405731] w l12xx: power down -nvs.bin Writing mac address 00:00:00:00:00:00 to file /lib/firmware/ti-connectivity/wl12 71-nvs.bin Calibration done. FEM1 has 1 bands. AutoFEM is off. Resulting nvs is /lib/firmwa re/ti-connectivity/wl1271-nvs.bin [ 10.053131] wl12xx: loaded Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Starting PVR [ 10.651428] pvrsrvkm: Unknown parameter `/lib/modules/3.2.0/kernel/drivers/gp u/pvr/pvrsrvkm.ko' Error: could not insert module /lib/modules/3.2.0/extra/pvrsrvkm.ko: Unknown sym bol in module Could not find pvrsrvkm driver Starting Lighttpd Web Server: lighttpd. 2013-06-26 00:02:03: (log.c.166) server started Starting UIM2 GUI application[ 11.361450] gadget: Mass Storage Function, vers ion: 2009/09/11 [ 11.367675] gadget: Number of LUNs=1 [ 11.371520] lun0: LUN: removable file: /dev/mmcblk0p1 [ 11.376922] gadget: Mass Storage Gadget, version: 2009/09/11 [ 11.382934] gadget: userspace failed to provide iSerialNumber [ 11.389038] gadget: g_mass_storage ready [ 11.393280] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 11.398864] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus numbe r 2 [ 11.406738] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.413818] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 11.421386] usb usb2: Product: MUSB HDRC host driver [ 11.426544] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd [ 11.432098] usb usb2: SerialNumber: musb-hdrc.0 [ 11.437438] hub 2-0:1.0: USB hub found [ 11.441375] hub 2-0:1.0: 1 port detected *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** Stopping Bootlog daemon: bootlogd. umount: can't umount /mnt/.psplash: Device or resource busy _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2013.05 am335x-evm ttyO0 am335x-evm login: root root@am335x-evm:~# cd .. root@am335x-evm:/home# ./gfx_check.sh WSEGL settings [default] WindowSystem=libpvrPVR2D_FRONTWSEGL.so.1 ------ ARM CPU information Processor : ARMv7 Processor rev 2 (v7l) BogoMIPS : 718.02 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x3 CPU part : 0xc08 CPU revision : 2 Hardware : am335xevm Revision : 0000 Serial : 0000000000000000 ------ SGX driver information cat: can't open '/proc/pvr/version': No such file or directory ------ Framebuffer settings mode "800x480-62" # D: 30.000 MHz, H: 32.433 kHz, V: 61.895 Hz geometry 800 480 800 960 32 timings 33333 39 39 29 13 47 2 rgba 8/16,8/8,8/0,8/24 endmode Frame buffer device information: Name : DA8xx FB Drv Address : 0x9f400000 Size : 3072000 Type : PACKED PIXELS Visual : TRUECOLOR XPanStep : 0 YPanStep : 1 YWrapStep : 0 LineLength : 3200 Accelerator : No ------ Rotation settings 0 ------ Kernel Module information Module Size Used by g_mass_storage 37599 0 wl12xx_sdio 3986 0 wl12xx 202633 0 mac80211 289010 1 wl12xx cfg80211 189234 2 mac80211,wl12xx ------ Boot settings console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none ------ Linux Kernel version Linux am335x-evm 3.2.0 #1 Thu Feb 20 07:57:35 EST 2014 armv7l GNU/Linux root@am335x-evm:/home# cd /opt/ root@am335x-evm:/opt# ls gfxlibraries gfxsdkdemos ltp root@am335x-evm:/opt# cd gfxlibraries/ root@am335x-evm:/opt/gfxlibraries# ls gfx_dbg_es8.x gfx_rel_es8.x root@am335x-evm:/opt/gfxlibraries# cd gfx_dbg_es8.x/ root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# ls bufferclass_ti.ko libsrv_um.so glsltest1_fragshaderA.txt libsrv_um_dri.so glsltest1_fragshaderB.txt libusc.so glsltest1_vertshader.txt libuseasm.a install.sh libusp.a install_dri.sh omaplfb.ko libEGL.so pvr2d_test libEGL_eglimage.so pvr_drv.so libGLES_CM.so pvrsrvctl libGLES_CM_eglimage.so pvrsrvkm.ko libGLESv2.so rc.pvr libGLESv2_eglimage.so rc_dri.pvr libIMGegl.so services_test libIMGegl_eglimage.so sgx_blit_test libPVRScopeServices.so sgx_clipblit_test libffgen.a sgx_flip_test libglslcompiler.so sgx_init_test libglslcompiler_eglimage.so sgx_render_flip_test libpvr2d.so xeglinfo libpvrPVR2D_BLITWSEGL.so xgles1_texture_stream libpvrPVR2D_DRIWSEGL.so xgles1test1 libpvrPVR2D_FLIPWSEGL.so xgles2_texture_stream libpvrPVR2D_FRONTWSEGL.so xgles2test1 libpvrPVR2D_LINUXFBWSEGL.so xmultiegltest libsrv_init.so xorg.conf root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# insmod pvrsrvkm.ko [ 52.068206] PVR: PVRCore_Init [ 52.073791] PVR: PVRSRVDriverProbe(pDevice=df7f9400) [ 52.079101] PVR: EnableSystemClocks: Enabling System Clocks [ 52.085083] PVR: GPTIMER11 clock is 24MHz [ 52.089904] ------------[ cut here ]------------ [ 52.094787] WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0x88/0xa8() [ 52.101440] sysfs: cannot create duplicate filename '/bus/platform/devices/pv rsrvkm' [ 52.109527] Modules linked in: pvrsrvkm(O+) g_mass_storage wl12xx_sdio(O) wl1 2xx(O) mac80211(O) cfg80211(O) [last unloaded: wl12xx_sdio] [ 52.122375] Backtrace: [ 52.124938] [] (dump_backtrace+0x0/0x10c) from [] (dump_s tack+0x18/0x1c) [ 52.133758] r6:c00fc5f8 r5:00000009 r4:de161d18 r3:c05f7f0c [ 52.139709] [] (dump_stack+0x0/0x1c) from [] (warn_slowpa th_common+0x54/0x6c) [ 52.149017] [] (warn_slowpath_common+0x0/0x6c) from [] (w arn_slowpath_fmt+0x38/0x40) [ 52.158905] r8:00000001 r7:df3cf000 r6:df3cf000 r5:df3d8e50 r4:ffffffef [ 52.165740] r3:00000009 [ 52.168487] [] (warn_slowpath_fmt+0x0/0x40) from [] (sysf s_add_one+0x88/0xa8) [ 52.177764] r3:df3cf000 r2:c05117ac [ 52.181518] [] (sysfs_add_one+0x0/0xa8) from [] (sysfs_do _create_link+0xf8/0x1e0) [ 52.191131] r7:de161d70 r6:df013db0 r5:df3d8e50 r4:df3d8f40 [ 52.197082] [] (sysfs_do_create_link+0x0/0x1e0) from [] ( sysfs_create_link+0x14/0x18) [ 52.207061] [] (sysfs_create_link+0x0/0x18) from [] (bus_ add_device+0xcc/0x184) [ 52.216522] [] (bus_add_device+0x0/0x184) from [] (device _add+0x430/0x574) [ 52.225524] r8:00000000 r7:c0617920 r6:bf1f70b0 r5:00000000 r4:bf1f70a8 [ 52.232360] r3:00000000 [ 52.235107] [] (device_add+0x0/0x574) from [] (platform_d evice_add+0xfc/0x1e8) [ 52.244476] [] (platform_device_add+0x0/0x1e8) from [] (p latform_device_register+0x28/0x2c) [ 52.255004] r7:de160000 r6:c063e4c0 r5:bf1f7280 r4:bf1f70a0 [ 52.261260] [] (platform_device_register+0x0/0x2c) from [ ] (PVRCore_Init+0xec/0x398 [pvrsrvkm]) [ 52.272186] r4:bf1f7280 r3:00000000 [ 52.276031] [] (PVRCore_Init+0x0/0x398 [pvrsrvkm]) from [ ] (do_one_initcall+0x128/0x1a8) [ 52.286315] [] (do_one_initcall+0x0/0x1a8) from [] (sys_i nit_module+0x3e4/0x1b68) [ 52.295989] [] (sys_init_module+0x0/0x1b68) from [] (ret_ fast_syscall+0x0/0x30) [ 52.305450] ---[ end trace a9fbf893cfba41eb ]--- [ 52.310363] PVR: PVRSRVDriverRemove(pDevice=df7f9400) [ 52.315887] PVR: DisableSystemClocks: Disabling System Clocks [ 52.322113] PVR_K:(Error): PVRCore_Init: unable to register platform device ( -17) [999, home/mike/Graphics_SDK_4_10_00_01/GFX_Linux_KM/services4/srvkm/env/li nux/module.c] Error: could not insert module pvrsrvkm.ko: File exists root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# lsmod Module Size Used by g_mass_storage 37599 0 wl12xx_sdio 3986 0 wl12xx 202633 0 mac80211 289010 1 wl12xx cfg80211 189234 2 mac80211,wl12xx root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# lsmodinsmod pvrsrvkm.ko      Error: could not load module pvrsrvkm: No such file or directory root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# ls bufferclass_ti.ko libsrv_um.so glsltest1_fragshaderA.txt libsrv_um_dri.so glsltest1_fragshaderB.txt libusc.so glsltest1_vertshader.txt libuseasm.a install.sh libusp.a install_dri.sh omaplfb.ko libEGL.so pvr2d_test libEGL_eglimage.so pvr_drv.so libGLES_CM.so pvrsrvctl libGLES_CM_eglimage.so pvrsrvkm.ko libGLESv2.so rc.pvr libGLESv2_eglimage.so rc_dri.pvr libIMGegl.so services_test libIMGegl_eglimage.so sgx_blit_test libPVRScopeServices.so sgx_clipblit_test libffgen.a sgx_flip_test libglslcompiler.so sgx_init_test libglslcompiler_eglimage.so sgx_render_flip_test libpvr2d.so xeglinfo libpvrPVR2D_BLITWSEGL.so xgles1_texture_stream libpvrPVR2D_DRIWSEGL.so xgles1test1 libpvrPVR2D_FLIPWSEGL.so xgles2_texture_stream libpvrPVR2D_FRONTWSEGL.so xgles2test1 libpvrPVR2D_LINUXFBWSEGL.so xmultiegltest libsrv_init.so xorg.conf root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# insmod omaplfb.ko [ 86.441619] omaplfb: Unknown symbol PVRGetDisplayClassJTable (err 0) Error: could not insert module omaplfb.ko: Unknown symbol in module root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# insmod bufferclass_ti.ko [ 92.481597] bufferclass_ti: Unknown symbol PVRGetBufferClassJTable (err 0) Error: could not insert module bufferclass_ti.ko: Unknown symbol in module root@am335x-evm:/opt/gfxlibraries/gfx_dbg_es8.x# cd ../.. root@am335x-evm:/opt# ls gfxlibraries gfxsdkdemos ltp root@am335x-evm:/opt# cd gfxsdkdemos/ root@am335x-evm:/opt/gfxsdkdemos# ls gfxinstallinfo.txt ogles ogles2 root@am335x-evm:/opt/gfxsdkdemos# cd ogles root@am335x-evm:/opt/gfxsdkdemos/ogles# ls Alum.pvr OGLESCoverflow CM_US_IL_CHICAGO_008_015_L.DAE.pod OGLESEvilSkull CM_US_IL_CHICAGO_008_016_L.DAE.pod OGLESFilmTV CM_US_IL_CHICAGO_009_014_L.DAE.pod OGLESFiveSpheres CM_US_IL_CHICAGO_009_015_L.DAE.pod OGLESFractal CM_US_IL_CHICAGO_009_016_L.DAE.pod OGLESFur CM_US_IL_CHICAGO_009_017_L.DAE.pod OGLESLighting CM_US_IL_CHICAGO_009_018_L.DAE.pod OGLESMouse CM_US_IL_CHICAGO_010_014_L.DAE.pod OGLESNavigation CM_US_IL_CHICAGO_010_015_H.DAE.pod OGLESNavigation3D CM_US_IL_CHICAGO_010_015_L.DAE.pod OGLESOptimizeMesh CM_US_IL_CHICAGO_010_016_H.DAE.pod OGLESParticles CM_US_IL_CHICAGO_010_016_L.DAE.pod OGLESPolyBump CM_US_IL_CHICAGO_010_017_H.DAE.pod OGLESSkybox CM_US_IL_CHICAGO_010_017_L.DAE.pod OGLESTrilinear CM_US_IL_CHICAGO_010_018_L.DAE.pod OGLESUserClipPlanes CM_US_IL_CHICAGO_011_013_L.DAE.pod OGLESVase CM_US_IL_CHICAGO_011_014_L.DAE.pod Satyr.pod CM_US_IL_CHICAGO_011_015_H.DAE.pod SatyrOpt.pod CM_US_IL_CHICAGO_011_015_L.DAE.pod Scene.pod CM_US_IL_CHICAGO_011_016_H.DAE.pod Skirting.pvr CM_US_IL_CHICAGO_011_016_L.DAE.pod TV.pvr CM_US_IL_CHICAGO_011_017_H.DAE.pod TVCase.pvr CM_US_IL_CHICAGO_011_017_L.DAE.pod TVSpeaker.pvr CM_US_IL_CHICAGO_011_018_L.DAE.pod Table.pvr CM_US_IL_CHICAGO_012_014_L.DAE.pod Wall.pvr CM_US_IL_CHICAGO_012_015_L.DAE.pod balloon.pvr CM_US_IL_CHICAGO_012_016_L.DAE.pod cameratrack.pod CM_US_IL_CHICAGO_012_017_L.DAE.pod cameratrack2d.pod CM_US_IL_CHICAGO_013_015_L.DAE.pod o_model.pod CM_US_IL_CHICAGO_013_016_L.DAE.pod skybox1.pvr Camera.pvr skybox2.pvr FilmTVScene.pod skybox3.pvr Floor.pvr skybox4.pvr HotAirBalloon.pod skybox5.pvr Mesh.pod skybox6.pvr root@am335x-evm:/opt/gfxsdkdemos/ogles# ./OGLESLighting root@am335x-evm:/opt/gfxsdkdemos/ogles# ./OGLESLighting strace execve("./OGLESLighting", ["./OGLESLighting"], [/* 19 vars */]) = 0 brk(0) = 0xa7000 uname({sys="Linux", node="am335x-evm", ...}) = 0 access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or directory) mmap2(NULL, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40 022000 access("/etc/ld.so.preload", R_OK) = -1 ENOENT (No such file or directory) open("/etc/ld.so.cache", O_RDONLY|O_CLOEXEC) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=15271, ...}) = 0 mmap2(NULL, 15271, PROT_READ, MAP_PRIVATE, 3, 0) = 0x400e7000 close(3) = 0 access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEX EC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/neon", 0xbebee3b0) = -1 ENOENT (No such fil e or directory) open("/lib/arm-linux-gnueabihf/tls/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/tls/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOE NT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/tls", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such fil e or directory) open("/lib/arm-linux-gnueabihf/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOE NT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such fil e or directory) open("/lib/arm-linux-gnueabihf/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENO ENT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOE NT (No such file or directory) stat64("/lib/arm-linux-gnueabihf/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/arm-linux-gnueabihf/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT ( No such file or directory) stat64("/lib/arm-linux-gnueabihf", 0xbebee3b0) = -1 ENOENT (No such file or dire ctory) open("/usr/lib/arm-linux-gnueabihf/tls/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_C LOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEX EC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXE C) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No s uch file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEX EC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/tls/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/tls", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEX EC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/neon", 0xbebee3b0) = -1 ENOENT (No such fil e or directory) open("/usr/lib/arm-linux-gnueabihf/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/arm-linux-gnueabihf/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOE NT (No such file or directory) stat64("/usr/lib/arm-linux-gnueabihf", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directo ry) open("/lib/tls/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such fil e or directory) stat64("/lib/tls/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/tls/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/tls", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such fil e or directory) stat64("/lib/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such fil e or directory) stat64("/lib/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/lib/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/lib/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or dire ctory) stat64("/lib", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 open("/usr/lib/tls/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or dir ectory) open("/usr/lib/tls/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directo ry) open("/usr/lib/tls/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No s uch file or directory) stat64("/usr/lib/tls/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or director y) open("/usr/lib/tls/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directo ry) open("/usr/lib/tls/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/v7l/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/v7l/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directo ry) open("/usr/lib/v7l/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/v7l/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/v7l/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/v7l/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/v7l/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/v7l", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/neon/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/neon/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/neon/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such fil e or directory) stat64("/usr/lib/neon", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/vfp/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) stat64("/usr/lib/vfp", 0xbebee3b0) = -1 ENOENT (No such file or directory) open("/usr/lib/libGLES_CM.so", O_RDONLY|O_CLOEXEC) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\210b\0\0004\0\0\0"..., 5 12) = 512 lseek(3, 3682928, SEEK_SET) = 3682928 read(3, "\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 1 440) = 1440 lseek(3, 1340860, SEEK_SET) = 1340860 read(3, "A2\0\0\0aeabi\0\1(\0\0\0\0057-A\0\6\n\7A\10\1\t\2\n\3\f"..., 51) = 51 exit_group(1) = ? +++ exited with 1 +++ root@am335x-evm:/opt/gfxsdkdemos/ogles#