Audio Amplifiers

Browse by Tags

Audio Amplifiers

Welcome to the Audio Amplifiers Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".

Tags
You have subscribed to this tag. To view or manage your tag subscriptions, click here.   Close
You have unsubscribed from this tag. To view or manage your tag subscriptions, click here.   Close
You are currently viewing:
TAS5711
Related Posts

  • Wiki Page: Single Filter Vs Dual Filter in PBTL Mode

    Andres Blanco
    Q: SIngle FIlter Vs Dual FIlter in PBTL Mode Are there measurements for THD+N Vs Freq and THD+N Vs Po in PBTL Mode with single and dual filter? TAS5711 has PBTL jumper. Using that jumper and programming the device to be in PBTL mode (BTL jumper off) will give single filter responses. For dual...
    on May 20, 2010

  • Wiki Page: Thermal between TAS5711 and TAS5707.

    Andres Blanco
    Q: Thermal between TAS5711 and TAS5707. Both TAS5711 and TAS5707 RDS(ON)=180mohms, why thermal gap ~ 12~15 degree C under the same test condition? Thanks, Ian. A: Re: Thermal between TAS5711 and TAS5707. The TAS5711 and TAS5707 should have the same thermal performance. However, the TAS5711EVM...
    on Jun 21, 2010

  • Wiki Page: Using TAS570x in PBTL

    Don Dapkus
    Q: Using TAS570x in PBTL Almost all TAS570x must be paralleled after the LC filters. Only TAS5711 and later amplifiers can be paralleled before the LC filters (i.e. right at the OUT pins).
    on Sep 1, 2010

  • Forum Post: TAS5711 External MCU for I2C setting

    Edwin Ng
    Hi, I use software GDE to config TAS5711 as well, but once turn off the device, all of config will be clear, is it correct? if yes that means TAS5711 required a host MCU to restore the config once power up, am I right? B.R. Edwin Ng
    on Dec 31, 2010

  • Forum Post: TAS5713 in PBTL connection

    DJ
    I am using the TAS5713 in a PBTL configuration and had requested TI tech support insofar as the proper electrical connections. I received the attached drawing showing the connections. I have the TAS5713EVM board which is wired as 2 BTL (stereo) outputs and have noticed that the PCB layout for the boost...
    on Mar 5, 2011

  • Forum Post: Re: TAS5713 GDE failure

    Richard Greenway
    Don: Is there any mechanism for being notified of when the GUI tool will be available for the TAS5713 amplifier part? We just received our development board for this amplifier IC this morning. Out of curiosity, is it going to just be a change to the TAS5711 GDE? I have that running in a virtual...
    on Jul 29, 2011

  • Forum Post: TAS5711 power down power consumption

    Joe Lee
    Hi, I have a question on about TAS5711 What would be the power consumption of TAS5711 when it is in power down status? I cant either find it in datasheet or application notes. Thanks. BR, Joe
    on Apr 19, 2012

  • Forum Post: DRC in TAS5711

    Robin
    Hello, Sir Why we need two DRCs in TAS5711, or what's the purpose of the lower band DRC. Thanks!
    on Oct 7, 2012

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use