This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: LMP8646
I wanted to use this IC as a current sensor so just for preliminary testing I used a sense resistor(Rsesne) of 0.5 ohms and gain resistance (Rg) of value 49.9K. The supply voltage given to the IC was 12V and the common mode voltage (Vcm) to the input terminals was 6V. I passed a current of 0.4 A. From this I calculated that the output voltage (Vout) would be 1.996 V however I was getting an output voltage of just 0.13 V.
I tried changing the currents to different values however I never got the expected value. The value that I got was always less than what I was expecting.
Jason Bridgmon, TI Sensing Products Applications Support
Current Shunt Monitor Video Training Series
Hall Effect Sensor Video Training Series
TI makes no warranties and assumes no liability for applications assistance or customer product design. You are fully responsible for all design decisions and engineering with regard to your products, including decisions relating to application of TI products. By providing technical information, TI does not intend to offer or provide engineering services or advice concerning your designs.
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
Thanks for using TI E2E Forums. I did some calculations with your application parameters and you are correct. With Rg=49.9k ohm, Rshunt=0.5 ohms, Vs = 12V and Load = 0.4A you should measure 1.996V in the output (Vout). I also ran a simulation on TINA and got the same results, see below.
For troubleshooting, please measure the voltage on the input pins of the device (between IN- and IN+) to make sure you are getting 200 mV. You can share your schematic with me, I am happy to review it for you.
TI Current Shunt Monitors Applications Support
In reply to Mayrim Verdejo:
In reply to Atharva Karaguppi:
Please send me the schematic on pdf format. The Altium file you send me seems to be empty. Also, please measure the voltage between the inputs of the device (as I mentioned on previous reply) and let me know if it is 200mV or not. Refer to this training video for debugging and tips as of where to probe.
I was able to get your schematic using Eagle. My apologies, Eagle and Altium have same extensions.
I will need further clarification from the circuit. Why is there 2 headers for load? The headers pins are not labeled so I am not understanding the circuit. Also, is the IN- tied to Rsense? There is no nodes on the schematic so it is not clear to me if there is a connection.
Our typical circuit should look like the image below. Can you please confirm that your Rsense and Load are connected this way? Do you have a block diagram? Please confirm the Vsense value as well.
The load+ and load- are actually tied to IN+ and IN- respectively. Yes, the IN- pin is tied to the sense resistor and to the load- pin as well.The load shall be present between load+ and load-.And before load+ I shall place the battery or the voltage source.
Yes I have confirmed the value of Vsesne as well.
In the board is there presence of parasitic resistances in the path of the sense resistor which might be affecting the effective value of the sense resistor and hence resulting into inaccurate outputs ?
Thanks for the reply. Did you get to collect the measurements? In order for me to detect if the problem is with our INA we need to make sure that you are measuring the expected shunt voltage.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.