This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: OPA454
i wish to use the OPA454 as an non-inverter op-amp.
The input voltage coming from DAC (0V ~ 2.5V)
the gain in +40.
the supply voltage for V+ is 100V
the supply voltage for V- is 0V (GND)
I'm running the design with TINA-TI and for some reason I get this result:
but when I put the V+ to 95V and V- to (-)5V it work as expected:
So before i start the layout i would like to know if this device can be used for my application.
The OPA454 minimum common-mode voltage VCM is specified as (V–) + 2.5 V for linear operation. If you set the V- pin to 0 V and the input voltage is 0 V to +2.5 V as you have in the first example, the input signal falls below the the lower limit of the VCM range. When you move the V- pin down to -5 V, the 0 V to +2.5 V input then resides above the minimum VCM limit and linear operation is attained. You will need to use dual polarity supplies such as you have in the second case if you want to use a ground referenced input voltage, or the input voltage will need a dc level added that brings the input voltage range into the linear VCM range of (V–) + 2.5 V, to (V+) – 2.5 V.
If the closed-loop gain is set to +40 V/V and the maximum input is +2.5 V, that would result in a theoretical output voltage of +100 V. The amplifier cannot swing any closer to the supply rail than about (V+) – 1 V, for Io = 1 mA. Make sure you observe the Voltage Output Swing from Rail (Vo) in the Electrical Characteristics table.
Be sure to properly bias the OPA454 E/D and E/D COM pins in the actual circuit. The datasheet provides the necessary information about biasing these pins.
Precision Amplifiers Applications Engineering
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Thomas Kuehl:
Thank you Thomas for the fast reply.
Unfortunately I can't use dual supply voltages or a bias DC voltage for the input signal.
I guess I can't use this op amp for this design.
Can you recommend on other TI op amp that I can use?
I don't need high speed or big BW.
The main characteristics are to be able to get 110 volt in the VCC pin. (Without needs of bias or negetive voltage)
In reply to Itay Kalfa17:
My input voltage (input signal to the op amp) can vary only from 0V to 3.3V (using the DAC from the MSP430F5636). The supply voltage for the op amp is 100V (V+) and GND (V-).
Will it help if I use first stage amp (with low gain) and then go for the high gain ?
I have investigated ways to sum a positive offset with the 0 to +3.3 V input signal, but a problem arises because the the summed offset voltage voltage is multiplied by the closed-loop gain. That results in the OPA454 minimum output voltage being tens of volts, which likely isn't a usable solution.
I have developed one promising circuit based that is based on applying the OPA454 as a difference amplifier. The circuit relies on gaining up the input 0 to +3.3 V signal with an OPA196 RIRO op amp. Its output is applied to one input of the OPA454 difference amplifier, while a high reference voltage is applied to the other input. The output phase is inverted from the 0 to +3.3 V input signal so a second OPA454, connected as a gain of -1 V/V inverter.
The circuit hasn't been optimized, but as it stands it does result in an output that swings from about +2 V to +98 V, with a 0 to +3.3 V ground-referenced input. You can see the preliminary circuit below. Note that I used a sine wave input so any clipping would be evident in the simulations.
If this appears to be of interest I can further refine it for a more practical circuit. Right now it is using a number of voltages sources that could be reduced to something powered off the +100 V supply.
The E/D and E/D COM pins are discussed in the OPA454 datasheet Feature Description section, 9.3.6 ENABLE and E/D Com. The Electrical Characteristics table on Pg. 6 provides the voltage level requirements for E/D and E/D COMM pins. See the section of the table, E/D (ENABLE/DISABLE) PIN.
Thanks for your help, I really don't want to use a full bridge and PWN for my application, so i decided to create -3V to the design.
I have built the follow circuit:
The scope looks good for me, I really want to know what do you think about this set-up (I don't need more then 10mA input current). thank you again for your help.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.