Forums

Hi, Alexandr,

I'm not sure what sure what "SPI 8" means. Can you explain in a little more detail what you're trying to do?

-d2

DIX4192EVM-PDK - EVAL MODUL FOR DIX4192

in the datasheet for this module is written that it is necessary select SPI 16bit. But the pictures painted in the same SPI 8 bit. Is it possible to use 8-bit SPI to control this chip with a microcontroller?
and if possible then tell me how to do it.

and even how to switch modes and I2C fast I2C slow with the microcontroller.

I bought DIX4192EVM-PDK

Disc with the programs of the damaged

Support refuses to help

Could you put on the file server software for the DIX4192EVM-PDK?

thank you

Hi, Alexandr,

Sorry for your trouble! let me see if I can locate the necessary files for you.

When you say it was damaged, what do you mean? Was the disk physically broken?

I am not 100% sure, but I suspect the software doesn't work on Win7.

-d2

Hello

The disc is damaged when you first removing from the package.

The layer-carrying sticks to a package
Layer crumbled from the disk.
The disc is not a quality.

Please send the files from the disk to my registration e-mail 

Hi, Alexandr, 

Wow! that is amazing. It's not even that old, I'm surprised that it's like that already!

I will post the files when I round them up.

-d2

Hello

The board had to return

We wait another

Repeat of the previous posts:

"in the datasheet for this module is written that it is necessary select SPI 16bit. But the pictures painted in the same SPI 8 bit. Is it possible to use 8-bit SPI to control this chip with a microcontroller?
and if possible then tell me how to do it.

and even how to switch modes and I2C fast I2C slow with the microcontroller"

Best Regards

Alexandr

Hi, Alexandr,

OK, you returned the EVM and asked for a new one. Great! Hopefully that one won't have a bad CDROM in it, too.

The EVM MUST be run in SPI 16 bit mode.

-d2

Hello

I got a new CD, but the software is not installed correctly.

NI VISA 3.2 is not installed. screenshot in attachment

msiserver up and running properly in Administrator account

Maybe the disk is missing a file?

Help please. The project is not progressing.

Alexandr,

Sorry for all your troubles...

This GUI only runs in XP. Are you trying to run it in win7?

You might also try changing your computer's language to English, but I highly doubt that will help.

-d2

I tested the install on three computers with XP and one with Win7

result is the same everywhere

I'll try on a computer where there is no other language than English

I think the problem is that the device is determined solely by the unknown

Installation *.Inf does not lead to any changes

Alexandr

hello
we try to start dix4192
i2c speed 100 kHz
we do

1) set pin 19 and 21 to 0
2) set jumper to i2s mode
3) set CPM to i2c mode
4) reset dix4192, than delay 1 sec
5) do start (wait when start end)
6) send E0 (address device)
7) send 01 (address register)
8) send 3f (data)
9) do stop
10) try to read (do start)
11) send E0 (address device)
12) send 01 (address register)
13) do repeat start
14) send E1 (address device)
15) take data
16) send noask
17) send stop

but DIX4192 dot answer any time. no write no read
what we do wrong ? what we must to do ?
datasheet poor. Can you say what we must to do 1) 2) 3) 4) etc

Hi,

I just bought the DIX4192EVM-PDK, and my CD is also scrap.  It looks pretty much like the one shown in the picture above.

Could you please put the CD content on an FTP link ?  I can create an FTP site if required...

Thanks.