DLP & MEMS

Browse by Tags

DLP & MEMS

Welcome to the DLP & MEMS Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".

Sign In to Post
Tags
You have subscribed to this tag. To view or manage your tag subscriptions, click here.   Close
You have unsubscribed from this tag. To view or manage your tag subscriptions, click here.   Close
You are currently viewing:
DLPC200
Related Posts

  • Forum Post: Which is correct between datasheet and schematic?

    Keisuke
    Hi, There are differences between datasheet "dlpz004a.pdf" and Logic's Schematic regarding Table9-1 terminal interconnection. Which is correct? schematic datasheet RSVD_G5 (A18) LED drive NC RSVD_G6 (A19) LED drive NC RSVD_S0 (AA24) Pull-up & Pull-down NC ...
    on Nov 16, 2011

  • Forum Post: DLPC200 Handling of Unused Pins

    Seishin
    Hi All, I have a question about DLPC200 below. How should I handle unused pins on DLPC200,when not using USB Interface and Illumination Driver Control Interface. The pins are LED_ and USB_ and PWM0/1/2/3. (NC?) Regards, Seishin
    on Feb 13, 2012

  • Forum Post: DLPC200 Current Consumption

    Kanji Shibatani
    Hello I saw dlpc200 data sheet dlps014b, but I could not find the spec of power consumption. Customer had started design, and they don't just copy Light Commander, but want to know the spec. Would you please let me know the information of dlpc200 following? ( If it depends on frame rate...
    on Feb 18, 2012

  • Forum Post: Re: VTT current

    Kanji Shibatani
    Dear Fizix san Thank you for your reply. I had tried to measure VTT current on Lightcommander by myself, however TPS51100 VTT output pattern tied to DDR directly, so it was really very hard . Cusomter know TPS51100 can handle 3A peak sink/source current, and also they will use TPS51100&TPS51116...
    on Mar 1, 2012

  • Forum Post: VTT current

    Kanji Shibatani
    Hello Would you please let us know the VTT supply Current for DLPC200 and DDR2 ( MT47H32M16HR-3)? In the oteher word, the Light Commander has two VTT current source (TPS51100), but would you please let us know the supply current for each VTT_B2 and VTT_B3_B4? ( it is too hard to measure it...
    on Feb 27, 2012

  • Forum Post: DLPC200_Case to ambient Thermal resistance

    Kanji Shibatani
    Hello, This is the questions about DLPC200. According to DLPC200 data sheet "dlps014d" page20, Theremal resistance Rc is Rc= (Tj-Ta)/P - 3.3 deg-C/Watt ---- (1) Q1 If Pand Ta are were known, how can I estimate Tj (deg-C)? Q2 What is the usage of Eq.(1) ? I hope hearing from you...
    on Jun 25, 2012

  • Forum Post: Pattern Offset Adjustment in LightCommander

    LAKSHMINARAYANAN RAMASAMY
    Hi, I am using a DLP5500 kit in my current application. I need to download a single pattern (square pattern of 10 x 10 pixels) and I have to move this pattern within the field of view of the DMD. That is, I need to refresh the X&Y offset of this pattern at a higher speed (close to 1000 Hz). ...
    on Jan 29, 2013

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use