This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

DLP660TE: DLP660TE

Part Number: DLP660TE

Hello,

I am developing a 4K projector with DLP660TE.

Now I have completed PCB board and debugging main board.

But I can not download the image to FPGA by composer lite, and it occurs USB error, please see the pictures.

Before welding, I have download the DDP4422 image by programming tool, and I can get running information by UART.

Perhaps I have not get the serial flash information or USB not reset.

If some details wrong, please guide me.

Thanks for any help.

  • 660-log-1.log
    [BEGIN] 2017-12-08 11:22:20
    Debug opened on URT0
    EEPROM content is valid
    EEPROM: Initializing Slave EEPROM: 3320 bytes
    sysmon: System Startup State From AppCfg is 0
    sysmon: Notify uC ASIC is running.
    sysmon: 1.8V power enabled via PMD
    Serial Flash NVM = 0xEFCF
    sysmon: Low-power mode change cc = 1
    sysmon: Memory test cc = 1
    sysmon: System mailbox ID = f7ff44f4
    API version: 07.00.00
    App version: 07.00.00
    ASIC ID: 50
    ASIC Configuration: 4422
    Configuration layout versions:
         Seq Map: 44.21.0019
         SW Map: 44.21.0000
         EEPROM: 07.00.0000
    *****Through DDP_Init cw & seq*****
    projectorCtl: Opening projector control on USB
    digcontrolf: Cfg complete
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    illumination: Starting SSI Initialization...
      Configuring SPI Driver...
      Setting Packet Sizes...
      Setting Level Packet Bit Depth...
      Initializing SPI Driver...
      SPI Driver initialized...
      Reading SPI Driver ID...
    SPI Driver Infomation: MFG ID = 0x00, Hardware ID = 0x00, FirmwareID = 0x00...
      Configuring Red Timing Packet...
      Configuring Green Timing Packet...
      Configuring Blue Timing Packet...
      Setting drive levels to 0 for channel 0.
      Setting drive levels to 0 for channel 1.
    digcontrol: StopCurrentOperation complete
      Setting drive levels to 0 for cDED 
    2.
      Configuring Sensor. Type = 1.
      Configuring Sensor. Type = 1.
      Initializing CCI configuration...
    SSI_Calibration  EE_GetVAR command Successful...
      SSI initialization complete
    illumination: Completed illum_Init
    sysmon: Through _sysReset
    sysmon: System Startup State From AppCfg is 0
    sysEvent: SYSEVENT_START
    sysmon: MASTER ASIC
    Sysmon: Transition to normal operating mode
    systemmode: There are 4 defined System Modes 
    systemmode: TwoD System Mode Table Created 
    systemmode: HighSpeed System Mode Table Created 
    systemmode: XPR System Mode Table Created 
    systemmode: ThreeD System Mode Table Created 
    Illumination: Transition to operating mode
    DMD FUSE ID VALIDATED 
    illumination: DMD comm error in DMD_Power()
    source: EEPROM defined
    source: SetUserSFGColor = 0
    source: DisplaySFG Color = 0
    source: DisplaySFG size = 1358 x 1528
    pictcont: color profile defaults written to EEPROM
    illumination: Can't set up DMD
    sysmon: Fault in illumination transition to operating mode
    sysmon: Sysmon can't transition to operating mode
    illumination: Transition to standby
    illumination: Disabling SSI Illuminators.
    datapathf: autolock initialization passed 
    digcontrolf: Init complete
    digcontrolf: powerNormal complete
    datapathf: dig powerNormal
    datapathf: datapath_ConfigFPGAatStartup 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    pictcont: Setting the new system mode_num 0 
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    source: SPLASH_LoadImage reload addresses:  0xf9200000, 0xf7ff2534
    source: SPLASH_LoadImage addresses:  0xf9200000, 0xffffffff
    source: Loading RGB -> RGB CSC ta
    pictcont: Disable BrilliantColor  xdispfmt: Actuator Enabled set to 0
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    systemmode: TwoDTable released 
    systemmode: ThreeDTable released 
    systemmode: XPRTable released 
    systemmode: HiSpeedTable released 
    sysmon: _sysStandby - Transition to powerStandby
    sysmon: Can't start projection
    FPGA Write Unsuccessful, returned, 0
    dispfmt: minPan, pan, maxPan:0, 0, 0
             data = { 1390, 0, 1390 }
    dispfmt: minScan, Scan, maxScan:0, 0, 0
             data = { 1528, 0, 1528 }
    FPGA Write Unsuccessful, returned 249 
    ******* Try to set Color Profile 0 *******
    pictcont: Active Display is 2 
    pictcont: Internal Source is disp 249 
    FPGA Write Unsuccessful, returned 249 
    pictcont: Set gamma 0
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    datapathf: Transition to SPLASH_AT_STARTUP 
    digcontrol: StopCurrentOperation complete
    datapathf: Transition to SUSPENDED 
    In Bootloader: v6.0.B4
    Debug opened on URT0
    I2C Cmd Slave Task Started
    Slave: EEPROM Initialized from Master
    Slave EEPROM: Initialization Complete: 3320 bytes
    sysmon: System Startup State From AppCfg is 0
    sysmon: Notify uC ASIC is running.
    XPR Sysmon: Enabling XPR SSP Bus
    sysmon: Low-power mode change cc = 1
    sysmon: Memory test cc = 1
    sysmon: System mailbox ID = f7ff54cc
    API version: 07.00.00
    App version: 07.00.00
    ASIC ID: 50
    ASIC Configuration: 4422
    Configuration layout versions:
         Seq Map: 44.21.0019
         SW Map: 44.21.0000
         EEPROM: 07.00.0000
    *****Through DDP_Init cw & seq*****
    projectorCtl: Opening projector control on USB
    digcontrolf: Cfg complete
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    illumination: Starting SSI Initialization...
      Configuring SPI Driver...
      Setting Packet Sizes...
      Setting Level Packet Bit Depth...
      Initializing SPI Driver...
      SPI Driver initialization FAILED...
      Reading SPI Driver ID...
      SPI Driver ID read FAILED.
      Configuring Sensor. Type = 1.
      Initializing CCI configuration...
    SSI_Calibration  EE_GetVAR command Successful...
      SSI initialization complete
    illumination: Completed illum_Init
    sysmon: Through _sysReset
    sysmon: System Startup State From AppCfg is 0
    digcontrol: StopCurrentOperation complete
    sysEvent: SYSEVENT_START
    sysmon: SLAVE ASIC
    Sysmon: Transition to normal operating mode
    systemmode: There are 4 defined System Modes 
    systemmode: There are 4 defined System Modes 
    systemmode: TwoD System Mode Table Created 
    systemmode: HighSpeed System Mode Table Created 
    systemmode: XPR System Mode Table Created 
    systemmode: ThreeD System Mode Table Created 
    Illumination: Transition to operating mode
    illumination: Enabling SSI Driver...
    source: EEPROM defined
    source: SetUserSFGColor = 0
    source: DisplaySFG Color = 0
    source: DisplaySFG size = 1358 x 1528
    pictcont: color profile defaults written to EEPROM
    datapathf: autolock initialization passed 
    digcontrolf: Init complete
    digcontrolf: powerNormal complete
    datapathf: dig powerNormal
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    source: SPLASH_LoadImage reload addresses:  0xf93763e0, 0xf7ff2534
    source: SPLASH_LoadImage addresses:  0xf93763e0, 0xffffffff
    source: Loading RGB -> RGB CSC table
    source: DisplaySplash size = 1390 x 1528
    dispfmt: minPan, pan, maxPan:0, 0, 0
             data = { 1390, 0, 1390 }
    dispfmt: minScan, Scan, maxScan:0, 0, 0
             data = { 1528, 0, 1528 }
    ******* Try to set Color Profile 0 *******
    pictcont: Active Display is 2 
    pictcont: Internal Source is displayed 
    pictcont: Set gamma 0
    datapathf: Transition to SPLASH_AT_STARTUP 
    XPR Illumination: Initializing XPR
    XPR Illumination: XPR Initialization complete
    illumination: DMD Unparked
    sysmon: Transition to normal mode complete
    source: DisplaySFG Color = 0
    source: DisplaySFG size = 1358 x 1528
    ******* Try to set Color Profile 0 *******
    pictcont: Active Display is 1 
    pictcont: Internal Source is displayed 
    pictcont: Set gamma 0
    datapathf: Transition to BEGIN_SCAN 
    digcontrolf: ConfigureForSearch complete
    datapathf: Transition to LOOK_FOR_SYNCS 
    ALC:    0	     1516	AL_CHANNEL_RESET
    warmUpTimer is complete
    sysmon: System Startup State From AppCfg is 0
    sysEvent: SYSEVENT_WARMUP
    In Bootloader: v6.0.B4
    Debug opened on URT0
    EEPROM content is valid
    EEPROM: Initializing Slave EEPROM: 3320 bytes
    sysmon: System Startup State From AppCfg is 0
    sysmon: Notify uC ASIC is running.
    sysmon: 1.8V power enabled via PMD
    Serial Flash NVM = 0xEFCF
    sysmon: Low-power mode change cc = 1
    sysmon: Memory test cc = 1
    sysmon: System mailbox ID = f7ff44f4
    API version: 07.00.00
    App version: 07.00.00
    ASIC ID: 50
    ASIC Configuration: 4422
    Configuration layout versions:
         Seq Map: 44.21.0019
         SW Map: 44.21.0000
         EEPROM: 07.00.0000
    *****Through DDP_Init cw & seq*****
    projectorCtl: Opening projector control on USB
    digcontrolf: Cfg complete
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    illumination: Starting SSI Initialization...
      Configuring SPI Driver...
      Setting Packet Sizes...
      Setting Level Packet Bit Depth...
      Initializing SPI Driver...
      SPI Driver initialized...
      Reading SPI Driver ID...
    SPI Driver Infomation: MFG ID = 0x00, Hardware ID = 0x00, FirmwareID = 0x00...
      Configuring Red Timing Packet...
      Configuring Green Timing Packet...
      Configuring Blue Timing Packet...
      Setting drive levels to 0 for channel 0.
      Setting drive levels to 0 for channel 1.
    digcontrol: StopCurrentOperation complete
      Setting drive levels to 0 for cDED 
    2.
      Configuring Sensor. Type = 1.
      Configuring Sensor. Type = 1.
      Initializing CCI configuration...
    SSI_Calibration  EE_GetVAR command Successful...
      SSI initialization complete
    illumination: Completed illum_Init
    sysmon: Through _sysReset
    sysmon: System Startup State From AppCfg is 0
    sysEvent: SYSEVENT_START
    sysmon: MASTER ASIC
    Sysmon: Transition to normal operating mode
    systemmode: There are 4 defined System Modes 
    systemmode: TwoD System Mode Table Created 
    systemmode: HighSpeed System Mode Table Created 
    systemmode: XPR System Mode Table Created 
    systemmode: ThreeD System Mode Table Created 
    Illumination: Transition to operating mode
    DMD FUSE ID VALIDATED 
    illumination: DMD comm error in DMD_Power()
    source: EEPROM defined
    source: SetUserSFGColor = 0
    source: DisplaySFG Color = 0
    source: DisplaySFG size = 1358 x 1528
    pictcont: color profile defaults written to EEPROM
    illumination: Can't set up DMD
    sysmon: Fault in illumination transition to operating mode
    sysmon: Sysmon can't transition to operating mode
    illumination: Transition to standby
    illumination: Disabling SSI Illuminators.
    datapathf: autolock initialization passed 
    digcontrolf: Init complete
    digcontrolf: powerNormal complete
    datapathf: dig powerNormal
    datapathf: datapath_ConfigFPGAatStartup 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    pictcont: Setting the new system mode_num 0 
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    source: SPLASH_LoadImage reload addresses:  0xf9200000, 0xf7ff2534
    source: SPLASH_LoadImage addresses:  0xf9200000, 0xffffffff
    source: Loading RGB -> RGB CSC ta
    pictcont: Disable BrilliantColor  xdispfmt: Actuator Enabled set to 0
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    systemmode: TwoDTable released 
    systemmode: ThreeDTable released 
    systemmode: XPRTable released 
    systemmode: HiSpeedTable released 
    sysmon: _sysStandby - Transition to powerStandby
    sysmon: Can't start projection
    FPGA Write Unsuccessful, returned, 0
    dispfmt: minPan, pan, maxPan:0, 0, 0
             data = { 1390, 0, 1390 }
    dispfmt: minScan, Scan, maxScan:0, 0, 0
             data = { 1528, 0, 1528 }
    FPGA Write Unsuccessful, returned 249 
    ******* Try to set Color Profile 0 *******
    pictcont: Active Display is 2 
    pictcont: Internal Source is disp 249 
    FPGA Write Unsuccessful, returned 249 
    pictcont: Set gamma 0
    FPGA Write Unsuccessful, returned 249 
    FPGA Write Unsuccessful, returned 249 
    datapathf: Transition to SPLASH_AT_STARTUP 
    digcontrol: StopCurrentOperation complete
    datapathf: Transition to SUSPENDED 
    
    [END] 2017-12-08 11:26:16
    

  • Hello Kelly,

    Thanks for using the DLP forums! Someone will get in contact with you through a private message to further discuss this issue.

    Regards,
    -Oscar
  • Hi, Oscar

    Thank you for your reply.

    I can download image today, and DLPC and FPGA boot OK.

    But DMD is no response and no projection.

    I have read boot information by UART maseter, but not sure the problem why.

    The UART read log is this.

    DLP660TE DEBUG.log
    [BEGIN] 2017/12/13 16:37:29
    In Bootloader: v6.0.B4
    
    Debug opened on URT0
    EEPROM content is valid
    EEPROM: Initializing Slave EEPROM: 3320 bytes
    sysmon: System Startup State From AppCfg is 0
    sysmon: Notify uC ASIC is running.
    sysmon: 1.8V power enabled via PMD
    
    Serial Flash NVM = 0xEFCF
    
    sysmon: Low-power mode change cc = 1
    sysmon: Memory test cc = 1
    sysmon: System mailbox ID = f7ff44f4
    API version: 07.00.00
    App version: 07.00.00
    ASIC ID: 50
    ASIC Configuration: 4422
    Configuration layout versions:
         Seq Map: 44.21.0019
         SW Map: 44.21.0000
         EEPROM: 07.00.0000
    *****Through DDP_Init cw & seq*****
    projectorCtl: Opening projector control on USB
    digcontrolf: Cfg complete
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    
    illumination: Starting SSI Initialization...
      Configuring SPI Driver...
      Setting Packet Sizes...
      Setting Level Packet Bit Depth...
      Initializing SPI Driver...
      SPI Driver initialized...
      Reading SPI Driver ID...
    SPI Driver Infomation: MFG ID = 0x00, Hardware ID = 0x00, FirmwareID = 0x00...
      Configuring Red Timing Packet...
      Configuring Green Timing Packet...
      Configuring Blue Timing Packet...
      Setting drive levels to 0 for channel 0.
      Setting drive levels to 0 for channel 1.
    digcontrol: StopCurrentOperation complete
      Setting drive levels to 0 for cDED 
    2.
      Configuring Sensor. Type = 1.
      Configuring Sensor. Type = 1.
      Initializing CCI configuration...
    SSI_Calibration  EE_GetVAR command Successful...
      SSI initialization complete
    illumination: Completed illum_Init
    sysmon: Through _sysReset
    sysmon: System Startup State From AppCfg is 0
    sysEvent: SYSEVENT_START
    sysmon: MASTER ASIC
    Sysmon: Transition to normal operating mode
    systemmode: There are 4 defined System Modes 
    systemmode: TwoD System Mode Table Created 
    systemmode: HighSpeed System Mode Table Created 
    systemmode: XPR System Mode Table Created 
    systemmode: ThreeD System Mode Table Created 
    Illumination: Transition to operating mode
    DMD FUSE ID VALIDATED 
    illumination: DMD comm error in DMD_Power()
    source: EEPROM defined
    source: SetUserSFGColor = 0
    source: DisplaySFG Color = 0
    source: DisplaySFG size = 1358 x 1528
    pictcont: color profile defaults written to EEPROM
    illumination: Can't set up DMD
    sysmon: Fault in illumination transition to operating mode
    sysmon: Sysmon can't transition to operating mode
    illumination: Transition to standby
    illumination: Disabling SSI Illuminators.
    datapathf: autolock initialization passed 
    digcontrolf: Init complete
    digcontrolf: powerNormal complete
    datapathf: dig powerNormal
    datapathf: datapath_ConfigFPGAatStartup 
    pictcont: Setting the new system mode_num 0 
    digcontrolf: powerStandby complete
    pictcont: Setting the new system mode_num 0 
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    source: SPLASH_LoadImage reload addresses:  0xf9200000, 0xf7ff2534
    pictcont: Disable BrilliantColor 
    dispfmt: Actuator Enabled set to 0
    source: SPLASH_LoadImage addresses:  0xf9200000, 0xffffffff
    source: Loading RGB -> RGB CSC table
    source: DisplaySplash size = 1390 x 1528
    pictcont: pictcont_SSI_CompleteSystemMode completed 
    pictcont: pictcont_CompleteSystemMode completed 
    pictcont: Set lamp waveform index if URT enabled for sequence mode number 0, cw mode 1
    pictcont: Setting the new system mode_num 0 completed 
    datapath: Set the default system mode complete 
    systemmode: TwoDTable released 
    systemmode: ThreeDTable released 
    systemmode: XPRTable released 
    systemmode: HiSpeedTable released 
    sysmon: _sysStandby - Transition to powerStandby
    sysmon: Can't start projection
    dispfmt: minPan, pan, maxPan:0, 0, 0
             data = { 1390, 0, 1390 }
    dispfmt: minScan, Scan, maxScan:0, 0, 0
             data = { 1528, 0, 1528 }
    ******* Try to set Color Profile 0 *******
    pictcont: Active Display is 2 
    pictcont: Internal Source is displayed 
    pictcont: Set gamma 0
    
    datapathf: Transition to SPLASH_AT_STARTUP 
    digcontrol: StopCurrentOperation complete
    
    datapathf: Transition to SUSPENDED 
    
    [END] 2017/12/13 16:38:06
    

    My DMD part NO is 2715-7039P.

    Can we discuss this problem through a private message?

    Thanks,