OMAPL137BPTPH-HT STARTERWARE EXAMPLE CODE

Naveen Chandra

Other Parts Discussed in Thread: OMAPL138, OMAPL137-HT

Hello All,

Am using OMAPL137BPTPH-HT controller which has a dual core(ARM9 + C674x). In my development i have planned to use only the DSP (C674x)Core.

So, can you please provide me the link to download the sample codes for OMAPL137BPTPH-HT controller!!??.

I found the examples (Starterware) for OAMPL137 ONLY.

Thanks & Regards

Naveen Chandra

over 8 years ago

0 Titusrathinaraj Stalin over 8 years ago

TI__Guru** 116100 points

Hi Naveen,
You can find starterware package only for OMAPL138 and not for OMAPL137.
You can also refer to the Quickstart CSL code for OMAPL137.

You can port the starterware code for OMAPL137.

processors.wiki.ti.com/.../StarterWare

processors.wiki.ti.com/.../QuickStartOMAPL1x_rCSL

You don't find big difference between OMAPL137 and OMAPL138.
EMIFB,some LPSC changes etc.,

0 Naveen Chandra over 8 years ago in reply to Titusrathinaraj Stalin

Expert 1280 points

Hi Titus,
Thanks for your quick reply. I just went through the Datasheet of omapl138. Your are absloutely right i didn't find major differences among these two controllers. Except OMAPL137 is meant for high temp application and OMAPL138 for commercial grade.
Also, i have just started my developmet work. I will ask you more questions if am stuck inside the while loop. Just kidding.!!
I will definitely get back to you if i have any queries.
Also, i dont have a target device. So, as u have informed me earlier there is no simulation on CCSV6.
So, how do i check my firmware step by step or go to step into mode?
Can i add my variables in the watch window?How do i put breakpoint and all??
Please give me your inputs on my above queries.
Waiting for your reply at the earliest.Thanks & RegardsNaveen Chandra

0 Titusrathinaraj Stalin over 8 years ago in reply to Naveen Chandra

TI__Guru** 116100 points

Oh! you are using OMAPL137-HT device then you may have some pins difference on EMIFB.
Please check the data sheet.

If you want to work and debug the example projects then you must need real hw board (at least EVM).
You can use emulators to run some algorithm kind of projects and get the performance.

Please refer to the following TI wiki pages.
processors.wiki.ti.com/.../Debug_Handbook_for_CCS
processors.wiki.ti.com/.../CCSv5_Getting_Started_Guide
processors.wiki.ti.com/.../GSG:Debugging_projects_v5
processors.wiki.ti.com/.../Category:CCS_Training

0 Sivaraj Kuppuraj over 8 years ago in reply to Titusrathinaraj Stalin

TI__Mastermind 35645 points

Hi,

Since the device OMAPL137-HT falls under high temperature category, I would request you to post this query in the below HiRel forum to be better answered:

e2e.ti.com/.../hirel

Thanks & regards,
Sivaraj K

0 Naveen Chandra over 8 years ago in reply to Titusrathinaraj Stalin

Expert 1280 points

Hi Titus,
Thanks for your reply and will go through the datasheet.
Thanks & RegardsNaveen Chandra

0 Naveen Chandra over 8 years ago in reply to Sivaraj Kuppuraj

Expert 1280 points

Hi Sivaraj,
Thanks for your input. I wil definitely post my query on HiRel forum also asap!!
Thanks & RegardsNaveen Chandra

Processors

Processors forum

OMAPL137BPTPH-HT STARTERWARE EXAMPLE CODE