This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: TLK10232
We use TLK10232 chip in the following configuration:(1) LS_side Altera FPGA (XAUI 3.125MHz 4lane) => TLK10232(2) HS_side TLK10232 (1lane 10G-KR) => opt.SFP module => optic Cable => opt.SFP module => TLK10232 (1lane 10G-KR)
When our PCBs operate with this particular chip, we faced the following problem: after initialization and reaching normal operative mode , HS FEC Correctable Error sometimes appeared. (Reg Addr:0xAC、Dev Addr:0x01)・Error occurrence frequency changes in every off/on. For example, error occurs 10 times per minute and we power off/on PCBs , initialize normal operative setting ,then, error occurs 10 times per day.・Error occurs in NOT ALL PCBs. Error occurs in some serial numbers.・The Low speed side is always good.・Length of traces from TLK10232 to SFP module is less than 20mm . (No vias or stubs)
We use this chip in 10GKR FEC Mode and following is initiation setting.1. Reset device (assert RESET_N and PDTRXA_N pins)2. Make sure the reference clock selection – we use 156.25 MHz ,so no register changes.3. Disable auto-negotiation by writing 1’b0 to 0x07.0000 bit 124. Disable link training by writing 16’h0000 to 0x01.00965. Write 16’h03FF to 0x1E.8020. 6. Write HS_ENTRACK (0x1E.0004 bit 15) to 1’b1 and HS_EQPRE (0x1E.0004 bits 14:12) to 3’b101. 7. Write 16’h0003 to 0x01.00AB - Enable 10GBASE-R FEC 8. Issue a data path reset by writing 1’b1 to 0x1E.000E bit 3.9. Clear Latched Registers (including 0x01.00AC)
We used information from the following :e2e.ti.com/.../1833175tlk10232_BringupProcedures_v2.pdftlk10232.pdf4520.TLK10034_link_training_app_note (10).doc
★We don’t understand the cause of HS errors and why sometimes(some chips) error occurs and don't occurs . Please can you help us!
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Jorge Llamas (SWAT):
In reply to user499018372:
In reply to Luis Omar Moran:
Thank you for your reply.
As I showed above, I configure the device for 10GBASE-KR mode and disable the auto-negotiation and link training.But I don't perform tuning refister values for HS_SERDES_CONTROL. Only try recommended value. (HS_ENTRACK (0x1E.0004 bit 15) to 1’b1 and HS_EQPRE (0x1E.0004 bits 14:12) to 3’b101))So I will try tuning (testing BER) first focus on HS_ENTRACK HS_EQPRE HS_PEAK_DISABLE HS_H1CDRMODE.
However, tuning all of these registers takes so much time because error occurence frequency greatly differs by chips (error occurs in some chips and never occurs in others) and every device on/off.
So, my Questions are following:1. Why error occurrence frequency GREATLY changes by chips and every device on/off? Is there any registers that can isolate cause of problem?
2. Do you have some recommended value for tuning registers (HS_ENTRACK HS_EQPRE HS_PEAK_DISABLE HS_H1CDRMODE) if I input our PCB ArtWork condidion (tarce length, impedance control, material, PCB layout etc)
We tried tuning register focus on HS_ENTRACK,HS_EQPRE,HS_PEAK_DISABLE,HS_H1CDRMODE.
However, HS fec error occurs in all register settings we tried.
We tried following register setting and checked fec error count.(About 30min. after link-up, we dumped fec correctable error count reg.)
setting A setting B setting C setting D setting E setting F setting GHS_ENTRACK 0x1 0x0 0x1 0x1 0x1 0x1 0x1HS_EQPRE 0x101 0x001 0x101 0x110 0x101 0x110 0x101HS_CDRFMULT 0x01 0x01 0x01 0x01 0x01 0x1 0x10HS_CDRTHR 0x01 0x01 0x01 0x01 0x01 0x1 0x01HS_PEAK_DISABLE 0x0 0x0 0x1 0x1 0x1 0x0 0x0HS_H1CDRMODE 0x0 0x0 0x0 0x0 0x1 0x0 0x0HS_TWCRF 0x00000 0x00000 0x00000 0x00000 0x00000 0x00000 0x00000------------------------------------------------------------------------------------------------------------------------------------------FEC error count 0xB 0x188 0x6 0x3 0x731 0x70 0x3
Do you have some suggestion about register setting or other hint for HS error?
Try the procedure without FEC function. Then try different values for the tuning, I know that this procedure is exhaustive. Could you send us the status of the next registers when you are performing the tuning?
Thank you for your reply,
I performed PRBS mode and checked HS_ERROR_COUNTER using two TLK10232EVM boards.Then, HS error occured in one of them.
I performed following initiation procedure for two boards after GUI opended. (0x07, 0x0000) 0x2000 write (Disable auto-negotiation)(0x01, 0x0096) 0x0000 write (Disable link training)(0x1E, 0x8020) 0x03FF write (VS_SERDES_CFG_OVERRIDE_CTRL) (0x1E, 0x0003) 0x5848 write (HS_SERDES_CONTROL_2)(0x1E, 0x0004) 0xD500 write (HS_SERDES_CONTROL_3)(0x1E, 0x000E) 0x0008 write (Issue a data path reset)(0x1E, 0x000B) 0x3F10 write (LOOPBACK_TP_CONTROL)(0x1E, 0x0010) read (HS_ERROR_COUNTER reg clear)
Then, leave 12 hours and read CHANNEL_STATUS_1 and HS_ERROR_COUNTER.
CHANNEL_STATUS_1 HS_ERROR_COUNTERTLK10232EVM Board No.1 0x200(1st read) 0x1803(2nd read) 0x0TLK10232EVM Board No.2 0x210(1st read) 0x1813(2nd read) 0x7
What is the difference between two boards and is it nessesarry tuning for TLK10232EVM Board?
Thank you for your reply, I will try your procedure.
By the way, is there any performance Test Report of HS Reciever?I found HS Trinsmitter performance reoport <www.ti.com/.../tidu347.pdf>However, I couldn't find HS Reciever test report. In SFF-8431, HS Recierver jitter tolerance (BER) specification is defined.(I send SFF-8431 and you will find jitter spec in page 32.)
Additionnarry, I also couldn't find LS side (xaui) test report.
Could you give me these testreports?
I tried your procedure.However, HS error has occured one of TLK10232EVM board again.I performed your procedure after GUI opened.Then, leave 12 hours and read CHANNEL_STATUS_1 and HS_ERROR_COUNTER.
CHANNEL_STATUS_1 HS_ERROR_COUNTERTLK10232EVM Board No.1 0x200(1st read) 0x1803(2nd read) 0x0TLK10232EVM Board No.2 0x310(1st read) 0x1803(2nd read) 0x2
Is there anything wrong with my procedure or setup, and could you give me HS reciever test reports?
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.