This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: TUSB7340
Support Path: /Product/Development and troubleshooting/
I'm experiencing some problems with USB2.0 (and lower) peripherals attached to the TUSB7340 USB3.0 xHCI host controller ports. The hardware platform is a custom board based on Xilinx Zynq UltraScale+ MPSoC (7EV family) with PCIe root complex enabled within the Processing System (x1 link at 5 Gb/s). The USB3.0 devices (hub/storage) work just fine, but the slower ones are not enabled/present in the system. Linux kernel version is v4.9 (xilinx rel-2017.3) with xhci-hcd driver used for USB3.0 host (arm64/xilinx_zynqmp_defconfig). Output from lspci and lsusb tools is provided below:
00:00.0 PCI bridge: Xilinx Corporation Device 7012 (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at e0100000 (32-bit, prefetchable) [size=8K] Bus: primary=00, secondary=01, subordinate=0c, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: e0000000-e00fffff Capabilities:  Power Management version 3 Capabilities:  Express Root Port (Slot-), MSI 00 Capabilities:  Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [10c] Virtual Channel Capabilities:  Vendor Specific Information: ID=1234 Rev=1 Len=018 <?>01:00.0 USB controller: Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller (rev 02) (prog-if 30 [XHCI]) Flags: bus master, fast devsel, latency 0, IRQ 54 Memory at e0000000 (64-bit, non-prefetchable) [size=64K] Memory at e0010000 (64-bit, non-prefetchable) [size=8K] Capabilities:  Power Management version 3 Capabilities:  MSI: Enable+ Count=1/8 Maskable- 64bit+ Capabilities:  Express Endpoint, MSI 00 Capabilities: [c0] MSI-X: Enable- Count=8 Masked- Capabilities:  Advanced Error Reporting Capabilities:  Device Serial Number 08-00-28-00-00-20-00-00 Kernel driver in use: xhci_hcd
:~# lsusb -t/: Bus 02.Port 1: Dev 1, class="root_hub", Driver=xhci_hcd/4p, 5000M/: Bus 01.Port 1: Dev 1, class="root_hub", Driver=xhci_hcd/4p, 480M
There is completely no kernel messages produced when keyboard or mouse are attached, but in case of usb storage/hub I can see some kernel output attaching to 2 of 4 available ports like that:
[ 3.440737] usb 1-2: new high-speed USB device number 2 using xhci_hcd[ 3.680735] usb 1-2: new high-speed USB device number 3 using xhci_hcd[ 4.115517] usb 1-2: new high-speed USB device number 4 using xhci_hcd[ 4.122036] usb 1-2: Device not responding to setup address.[ 4.332804] usb 1-2: Device not responding to setup address.[ 4.544763] usb 1-2: device not accepting address 4, error -71[ 4.668759] usb 1-2: new high-speed USB device number 5 using xhci_hcd[ 4.676095] usb 1-2: Device not responding to setup address.[ 4.888798] usb 1-2: Device not responding to setup address.[ 5.100758] usb 1-2: device not accepting address 5, error -71[ 5.111658] usb usb1-port2: unable to enumerate USB device
As reference, we have another one board with TUSB7320 host (yes, slightly different part with 2 ports only) based on Xilinx Zynq-7000 chip with PCIe root subsystem enabled in the FPGA fabric running on the same Linux kernel (built for armv7/xilinx_zynq_defconfig) with the same xhci-hcd driver used. And in this case no issues are reported: all kinds of USB peripherals work well. From system point of view, the only difference in USB3.0 design between these 2 boards lies in PCIe root complex implementation: "soft" IP for Zynq-7000 vs. "hardened" block for Zynq US+ MPSoC. The Linux drivers for these 2 PCIe hosts are also different: pcie-xilinx.c for soft PCIe host vs. pcie-xilinx-nwl.c for the integrated version in MPSoC chip. The configuration parameters for the both PCIe hosts are absolutely the same.
Do you have any thoughts on this?
In reply to Roberto Diaz:
In reply to Igor Gorokhov:
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.