Low Power RF & Wireless Connectivity

Browse by Tags

Low Power RF & Wireless Connectivity

Welcome to the Low Power RF & Wireless Connectivity Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".

Sign In to Post
Tags
You have subscribed to this tag. To view or manage your tag subscriptions, click here.   Close
You have unsubscribed from this tag. To view or manage your tag subscriptions, click here.   Close
You are currently viewing:
2.5.1
Related Posts

  • Forum Post: about MLME_ASSOCIATE.indication

    Bill Lee
    MLME_ASSOCIATE.indication is EVENT MAC_MLME_ASSOCIATE_IND ,Where can I handle to precess when a new device join to me?
    on Aug 8, 2012

  • Forum Post: problem about HA example in Z-Stack

    feng zhu1
    I am using CC2530 and Z-Stack 2.5.1a to develop my project. recently, I want to do this base on the HA example provided by Z-Stack. my questions: can the project base on HA example link to other products for HA profile from other vendors ? if not, why?
    on Aug 13, 2012

  • Forum Post: RE: why do the End Device send so much Data request packet?

    YiKai Chen
    Hi, This data request is come from polling rate of your end device. You can define the polling rate of your device to 5seconds for example and you will see the data request will appear in 5 seconds duration. Regards! YK Chen
    on Aug 22, 2012

  • Forum Post: Example GenericApp

    Francesco Sarta
    Hi guys, I'm new with zigbee and I use the example GenericApp in the Zstack 2.5.1, this example should send every 5 seconds the message " Hello World ", but seems to send the message every 15 seconds , how can I tell if it sends the right message? I use two CC2531 USB Dongle, one programmed...
    on Aug 21, 2012

  • Forum Post: RE: Voice over ZigBee with CC2530 in Z-stack?

    YiKai Chen
    Dears, I have the same question either. In my environment, I never have the data rate more than 10K bits per seconds running Zstack on CC2530. Could any TI employee give some explanation about the data rate mismatch so much with the spec?
    on Aug 30, 2012

  • Forum Post: RE: Rejoining Network

    YiKai Chen
    Dears, In my program, I use "zgWriteStartupOptions(ZG_STARTUP_SET, ZCD_STARTOPT_DEFAULT_NETWORK_STATE)" to clean up NV and do SystemReset() after that. You can have a try.
    on Aug 30, 2012

  • Forum Post: RE: Problem with 2530 + 2591

    YiKai Chen
    Dears, Try to use macRadioSetTxPower(20) to set the Tx power to 20dbm when you do system initializtion. Please remember to include mac_low_level.h. Regards!
    on Aug 31, 2012

  • Forum Post: Changing RFD_RCVC_ALWAYS_ON on the fly

    Val 83
    Hi, Is it possible to change RFD_RCVC_ALWAYS_ON from TRUE to FALSE on the fly ? Best regards, Valentin
    on Sep 20, 2012

  • Forum Post: ZStack-EXP5438-2.5.1.exe , 5438A and 5438Non-A compatible?

    Leo Choi
    Hi, is there any one know the if the Z-stack ver 2.5.1 for EXP5438 working the EXP5438A ? I have a project that require more pin out that cc2530 is not capable and considering using cc2520+EXP5438 pair? The local distributor told us not to use the non-A version development. http://www.ti.com...
    on Nov 13, 2012

  • Forum Post: ZStack 2.5.1, CC2530, Using Preconfigured Key without NV_RESTORE

    iR
    Big up y'all community brotherhood, I want to use security by cooking up a tasty ZigBee sandwich with a base of zgPreConfigKeys = TRUE and a dash of SECURE=1 . Unfortunately, it appears that I also have to enable NV_RESTORE even though I have no desire to use NVM, and it actually breaks my application...
    on Jun 26, 2012

  • Forum Post: Problem sending data to connected End Device from Coordinator

    Val 83
    Hello, We have a problem using ZIgbee with ZNP. We have started a network composed of one coordinator and one end device. End device connects properly to coordinator. Our problem : when doing an AF_DATA_REQUEST from coordinator to the registered end device, the message is not transfered but the...
    on Sep 20, 2012

  • Forum Post: CC2530 SPI Write Sequence - SBL early jump to Application code - zapPhySpiRun

    anil kolli
    Hi All, I am using "ZAP-MSP430-2.5.1" code. I have a doubt regarding cc2530 SPI write from Application processor. CASE 1: From zap_phy_spi.c file, SPI write is as follows.. -------------------------------------------------------------------------------------------------------------...
    on Mar 18, 2013

  • Forum Post: Signal-to-noise ratio on cc2530

    Darshan tinku
    Is there a way to find SNR of the channel in cc2530 chip at the receiver .In my project i specifically need SNR because i need to measure the state of the channel using this dynamically . I have also went through lot of threads in this forum related to s/n ratio but
    on Jun 18, 2013

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use