Low Power RF & Wireless Connectivity

Browse by Tags

Low Power RF & Wireless Connectivity

Welcome to the Low Power RF & Wireless Connectivity Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".

Sign In to Post
Tags
You have subscribed to this tag. To view or manage your tag subscriptions, click here.   Close
You have unsubscribed from this tag. To view or manage your tag subscriptions, click here.   Close
You are currently viewing:
ZTOOL
Related Posts

  • Forum Post: [ZTOOL, ZStack-EXP5438-2.4.0-1.4.0] NV Write -OK, but NV READ - Failed

    Young Cheol KIM
    Hello, In using the ZTool, I faced the below issue. I wrote the NV data successfully as but can't read the data. The length value is reported as zero. Additionally when I read the the data in the flash ( INFO page) thru the debug interface, it is read as 0xFF,... . <TX>11:44...
    on Jan 31, 2011

  • Forum Post: Implementing a new clusterin SE profile.

    Shreejesh Sasidharan67539
    Hi, I have a requirement of implementing a new cluster which has different attributes than of Simple metering. I am using CC2530 chip with Zstack. It has around 104 attributes. The problems i am facing are 1). When I tried to run both the clusters together ..i am recieving XDATA not enough error...
    on Mar 29, 2011

  • Forum Post: Re: Z-Stack SerialApp sample application.

    ismail HANCI;
    hi all, i am new at ZigBee stack. i was usign cc253x without stack. Now i am install the SerialApp Sample application but there are lots of question about that. there two cc2530Em with smartRF05EB 1.8. i used SW4 buton to bind activate and LED1 set on end device. i have never change the sample...
    on Apr 16, 2012

  • Forum Post: RE: sensordemo & mt tools issue

    ismail HANCI;
    i add all defines at SensorDemo application by Coordinator Compiler Options. But nothing changed. i add all at Home Automation application Coordinator compiler Options. I never run Ztool with this and the coordinator don't response my sys_ping Command(0xFE,00,21,01,20). am i doing Wrong. i spent...
    on May 3, 2012

  • Forum Post: RE: sensordemo & mt tools issue

    ismail HANCI;
    Hi, I can enable the Layer function folder on Ztool such as AF,ZDO,NWK etc. But most of them don't response correctly. in Ztool, I used Load Parameter buton for network information. But only IEEE adress can be read. Others are all N/A. I am using SimpleLight Example for Home Automation Profile...
    on May 24, 2012

  • Forum Post: RE: sensordemo & mt tools issue

    ismail HANCI;
    I am using last version Ztool and SYS folder functions are working. I could't run ZDO functions. some functions in Ztool and answers are in below. ZDO functions are not responded <TX>01:35:00.74 COM6 SYS_PING (0x2101) <RX>01:35:00.75 COM6 SYS_PING_RESPONSE (0x6101) Capabilities...
    on May 25, 2012

  • Forum Post: Home Automation Profile TI + other vendor problem

    ismail HANCI;
    Hi All, I have a coordinator (cc2531) and the temperature sensor for HA profile from different vendor. I know that the device joins my network. But I don't know how can i get the temperature value. I use Ztool, so how can I see my humidty and temperature values? My Enddevice has different...
    on May 30, 2012

  • Forum Post: RE: IEEE address of all devices

    stkr M10
    devices are not getting recognised through ztool. any suggestions would be helpful regards
    on Feb 6, 2013

  • Forum Post: Ztool : How to launch the network discovery by ZTOOL

    Zerhouni Adam
    Hi everyone, I'm new, the zigbee stuff, so forgive my lack of understanding. I'm working on Ztool using an usb Dongle CC2531 as coordinator. The stack is installed and ready to use. i have in the ZTOOL five Monitor and Test (MT) interface that is used for communication between the host tester...
    on Apr 22, 2013

  • Forum Post: toggle on/off ZPLUG with ZTOOL

    Zerhouni Adam
    Hi, i Have a Zplug as ZigBee device that i can communicate with and send commands using ZTOOL, the only problem is that i didn't find how to toggle on/off the ZPLUG using AF_DATA_REQUEST. i know that my destination address is correct, the destination endpoint is 1, and the cluster for the switch...
    on May 13, 2013

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use