Low Power RF & Wireless Connectivity
Options

Forums

CC debugger won't work with CC85XX development kit

This question is not answered
Igor Majki��
Posted by
on Nov 23 2011 05:52 AM
Prodigy60 points

I just received from my professor new CC85XX development kit.  The boards seem to work correctly, and pair correctly.

However, the CC Debugger doesn't seem to work correctly.  When connected to the PurePath Wireless AudioEB, with either a CC85XX, or CC85XX-CC2590 range extender module,  there is a steady RED light, indicating no RF device was found. 

 The SmartRF Studio program as well as the SmartRF Flash Programmer and the PurePath Wireless Configuration programs all show the CC Debugger as connected in the programs, so the USB drivers are working. 

I have completely uploaded the latest CC Debugger firmware, and still no change in the situation.

The failure occurs regardless of which of the 2 AudioEB boards is attached, and regardless of any combination of AudioEB and RF module from the CC85XX development kit.

i am runing software on 64 bit win7 and 32 bit XP but the problem remains the same

 

thanks

igor

(majkic.igor@gmail.com)

 

 

Report Abuse
All Replies
  • fernando rivas
    Posted by
    on Aug 09 2012 05:02 AM
    Prodigy50 points

    Sorry,

    I missed words: I have only one CCdebugger and I don´t have SmartRF05EB. I have SmartRF04EB but I think it is no possible to detect CC2511 with this board.

    Report Abuse
  • Kristoffer S
    Posted by
    on Aug 09 2012 05:08 AM
    Expert6050 points

    Hi Fernando,

    You say: "I have also tried step 8.2 but SmartRF Flash Programmer doesn´t detect CCDebugger again."

    When I do step 8.2 it looks like this when I'm done:


    Are you experiencing the same? If not, what are you experiencing?

    -Kristoffer

    --
    Thank you for clicking  Verify Answer  if this answered your question!

    Report Abuse
  • fernando rivas
    Posted by
    on Aug 09 2012 05:48 AM
    Prodigy50 points

    Hi Kristoffer,

    In my case, I´m experiencing almost the same, but my ccdebugger is detected by Smartrf Flash programmer when debug connector is rotate from the right position!

    So I have been able to update the firmware to the last FW version.

    Maybe something in CCdebugger board crashed, because I have tried all and there are no results.

    Thanks.

    Report Abuse
  • Kristoffer S
    Posted by
    on Aug 09 2012 06:12 AM
    Expert6050 points

    Fernando,

    "debug connector is rotate from the right possition"

    I don't quite understand. Are you talking about the 10-pin flat cable here? You shouldn't need this at all when updating the CC Debugger firmware. Then you only need the USB cable. So can you please show me a screen shot of your flash programmer after you have done the steps in 8.2 (a smilar picture to the one I have posted).

    -Kristoffer

    --
    Thank you for clicking  Verify Answer  if this answered your question!

    Report Abuse
  • fernando rivas
    Posted by
    on Aug 09 2012 06:49 AM
    Prodigy50 points

    Hi all,

    I have solved the problem!!

    I have discovered that LDO TPS79633 doesn´t work well, so I have replaced it with similar available one and I already debug!

    Thanks for your help! 

    I hope this solution could solve same of your problems too.

    Bye

    Report Abuse
12

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use