TI E2E Community
C2000 32-bit Microcontrollers Forum
DRV C2 8412 kit
Whether DRV C2 8412 kit will work in DVRC2 8312 GUI ?
While using DRV C2 8412, i couldn identify the proper Jtag name, pls find the attachment and suggest me the appropriate Jtage name pls.
Whether DRV C2 kit will work in CCSv4 or with CCSv5.1 too ?
Pls reply me !!!!!!!!!
the DRV8412-C2-KIT comes with a TMS320F28035 ISO controlCARD which includes XDS100v1 USB emulation on card.
I'm not sure why you mentioned GUI...GUI for DRV8412 and 8312 are quite different, with different .exe, different .out needed in Flash on the card, and different DRV baseboards.
Recently i have bought DRV C2 8412 kit, while connecting the h/w with XDS100 JTAG, i am facing so many problems.1. unrecoverable error, solutions, to recover this, i changed CMS settings, again i faced one more error. ()2. C28xx: Error connecting to the target: (Error -1135 @ 0x0) The emulator reported an error. Confirm emulator configuration and connections, reset the emulator, and retry the operation. (Emulation package 5.0.663.0) 3. while running DBJTAG :The JTAG IR and DR scan-paths cannot circulate bits, they may be broken.An attempt to scan the JTAG scan-path has failed.The target's JTAG scan-path appears to be brokenwith a stuck-at-ones or stuck-at-zero fault.
But i am unable to full fill CMS settings also, kindly help me pls
From the first post it looks like you may be configuring CCS for an XDS100v3. The emulator on the card you have should be an XDS100v1. Please select this in your target configuration. If this doesn't fix the issue, please post a screen shot of your target configuration.
Sorry to hear you're having trouble,
Have you supplied power to the motor driver baseboard? Because the JTAG on this kit is isolated, the target device cannot be powered through USB. Only the XDS100 may be powered through USB.
First i would thank you for all ur replies,
Since i have posted so many queries, even made call to TI asia, but still couldnt get enough responds, since they may be busy with some works.
So kind for ur reply !!!!!
Back to point:
yes i have given Pvdd supply to the base board, its 24v , right .
but still facing same props.
Hope u can help me !!!!!!
power to PVDD /GND
JP1 to VR1
F28035 ISO controlCARD SW3 ON (down)
LD3 on the card should be blinking if good code is loaded in flash
launch XDS100v1 F28035 emulator
LD3 should turn off
if not, probably something wrong with your controlCARD
Let me know try this procedure and come back to u by tomo sure,
I would thank all the fellows for their warm reply !!!!!!!!!!!!!
If after following Chris' instructions it is still not working check Windows device manager and see if XDS100 shows up there.
It should look like this:
Bit confused too !!!
Finally my system got connected with DRV C2 8412 kit !!!!
i was just followed the previous steps, moreover, when i gave unlock the Flash , it was made Unlock, so that it was easier to get communicate with board.
thanks to all , for ur valuable support.
But still little doubt, when i deploy my DRV8412 GUIv2.out file into my controller, i could be able to run only my motor 1 alone,. why not motor 2 ?
To make it run, what kind of changes need to be done.
Moreover, i would like to know,the extremity applications of DRV C2 8412 kit !!!!!! just confused with these applications area?
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.