This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: DRV10987EVM
May I know where can download DRV10987 EVM GUI parameter file?
Now Motor use Runtian ZWL12_22_2.5A.
BTW I also got some error message as below then how can I solve the issue?
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Eric Chen4:
Please refer to the DRV10987EVM User's Guide: http://www.tij.co.jp/jp/lit/ug/slou476/slou476.pdf
Specifically, max sure the DRV10987 is powered to the appropriate VCC and there is a voltage on the speed pin (by turning the potentiometer clockwise if you have the EVM). Make sure the USB2ANY is correctly connected to the device and open the DRV109xx Software (download is on the Tools and Software tab of the DRV10987 product folder) and select the DRV10987. Usually, the error you see is because the USB2ANY is not connect to the device correctly or the device is asleep since there's no voltage on the speed pin.
Section 5: Out of the Box Quick Start Guide in the user's guide has more information.
In reply to Cole Macias:
Thanks your information.
Would you kindly help to check if cna use "Runtian_ZWL12_22_2p5A.csv" to DRV1987 EVM?
BTW, we use WIN10 OS and still got the same error message and will find other OS to check again.
TI has stopped providing the Runtian configure .csv file, please refer to this E2E post for more details including how to get the motor spinning. In summary, we used to offer a motor with the EVM. However, TI no longer offers the motor in the EVM which removes the need for the file.
Please refer to the user's guide as mentioned before to get the EVM operational and then refer to the DRV10987 Tuning Guide to tune the motor.
Does this error occur every time you start up the EVM GUI? Or are you able to get the the Enable Configure button on the GUI to turn green and then you get the error some time (i.e. seconds) later?
Note that the GUI and LabView 2014 run time engine is compatible with Windows 10 and should not contribute to the error.
Yes, I still got the same error message every time when start up GUI and I also uninstall GUI then re-install again but still got the same message as below.
Would you have other better suggestion for our check again?
The below is our USB2ANY firmware version for your check again. It seem V22.214.171.124 version.
BTW, the below is full screen error message inculde GUI for your check again and now use OS is WIN10.
I have the same problem OS is WIN10 64-bit. I have the same error messages if I want to write parameters to the DRV10987 EEPROM.
I have a error message if I start the GUI:
Do you have the same message?
In reply to Ulf Herder:
No, this should need to install "LVRTE2014f2std.exe" file from http://www.ni.com/download/labview-run-time-engine-2014/4887/en/
I had installed the "LVRTE2014f2std.exe" and also I rebooted the PC before using the GUI.
I have looked with my scope on the I²C clock and data line everything seem to be normal.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.