This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: LMG5200
I am using two LMG5200 cascaded (Q1+Q2 is one package and Q3+Q4 is the other package) as can be seen in the schematics below. Here Q1 and Q3 are switched at the same time, while Q2 and Q4 are also switched at the same time. The Q1+Q3 pair and Q2+Q4 pair are never switched at the same time.
For my test I was switching at 100kHz, with around 2µs between Q1+Q3 and Q2+Q4. However, I saw that the resonant tank (Cr+Lr) was being discharged when Q2+Q4 are switched on. It seems that Q2 and Q3 are conducting at the same time, while the control signal for Q2 is high and the control signal for Q3 is low.
Does anyone have any idea what might go wrong, why Q2 and Q3 seem to short the resonant tank?
I have used a 2-channel isolator for the HI and LI signals of the upper LMG5200 with a 5V supply with respect to the main input voltage.
Used control signals:
there are a few things that I would need to understand to give you a good answer:
1.Is there a load connected to Vout?
2.what does the Vout voltage look like during the transitions?
3.If you apply a voltage source directly across the tank with everything else unpowered how much leakage current to you get (I would expect a lot less than 1mA) - also check the integrity of the capacitor.
4.can you check the off state Rdson for Q3 and Q3 these should be several 100k ohm.
If all the above look good there might be something associate with the actual operation of the circuit and might need further information.
If at any time you don't feel comfortable sharing information on the e2e we can carry the exchange privately.
Thank you and best regards,
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Alberto Doronzo:
1. Yes, a 4.7kΩ resistor
2. In blue the output voltage, in green the voltage over the resonant tank, in yellow the current through the tank and in red the control signal of Q1.
3. At 5V over the tank I measured <1µA
4. I measured the off-state Rdson for all switches at >1MΩ
In reply to Wouter Krikken:
everything seems to be pointing to a health circuit.
One extra test that you can do to ensure the the LMG5200 are operating correctly is verifying that all the FETs can turn ON properly.
Make all Hi and LI high-level (don't power the bus voltage!) and check that the chain resistance is tens of milli-ohms.
If that checks ok, then the components are fine, and there has to be something to do with the values or operation of the circuit.
In that case to further assist you I would need a schematic to read the correct values of components.
happy I could be of help and and I am glad that you managed to fix the circuit!
Feel always free to reach out if you have questions.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.