This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: tps65185
we are working on Eink display and we used PMIC TPS65185 for that please see below is our schematic.
we used imx7 processor for communication with eink.
we have facing some issue on that PMIC below is our issue on TPS65185.
- for powerup all rail and IIC communication we high WAKEUP pin and low POWERUP pin. it then we configure all register POWERUP, VNEG, VEE, VPOS, VDDH, is enabled using resistor. then we take PMIC into active mode.
- but internal booster DCDC1 and DCDC2 is in regulation. and VNEG and VEE is also in regulation but VPOS and VDDH is not in regulation.
- we check int2 register and its get error 10h so VPOS_UV interput come from IC because of VPOS is only generate 2.5V .
- for that we check internal register VCOM_EN which is high.
please see below is our schematic.
please explain why VPOS and VDDH is not in regulation.
VPOS has a soft start current limit ~50mA, where it seems to stay in constant current mode until regulation voltage is reached. Is the output staying at 2.5V or slowly rising?
Staying at 2.5V might indicate a ~50ohm load to gnd on that rail.
Find the right power solution for your processor or FPGA. Visit www.ti.com/SoCPower today!
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Richard Solarski:
thanks for your reply,
output spikes to 3.7V and keeps falling. and we have not connect any load on any rail.
and that voltage is not stying.
In reply to ARSADHUSAIM MOMIN:
Can you measure the impedance on that rail? It still sounds like the LDO is overloaded. Removing any additional components on that rail might help.
The TPS651851 is pin-to-pin compatible with the TPS65185, with a slightly higher current capability, but since this occurs during soft-start/startup it may still behave similarly.
please see my schematic i am not connecting any additional components on VPOS rail.
because we have only two rail for VPOS one is input and i check that is +16V from DCDC1 and from output side i connect only 4.7uf capacitor which is recommended
we will connect all rail with jumper wire and i will also check all pin to pin connection on connector side so it is not shorting on any pin.
after connecting all pin with GPIO then all voltage is generated.
please see our connector schematic. below if we need to change anything and then work.......
you can compare it with our schematic
we also check all require GPIO using high low functionality it will work fine so its dont have GPIO issue.
so after connecting PMIC on connector then why VPOS is not generating so if impedance trace issue is here then it will not work with jumper also.
i dont know why this VPOS is not generating.
please help asap,
If I understand correctly, this connector supplies the PMIC, and VPOS functions properly when it is replaced with jumpers, is this correct?
How was 5V0 applied to the PMIC during the GPIO test? Does it behave differently when supplied through the connector?
thanks for your great understanding,
5V0 we connect from imx7 sabre board using jumper wire.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.