AC/DC and Isolated DC/DC Power

Browse by Tags

AC/DC and Isolated DC/DC Power

Welcome to the AC/DC and Isolated DC/DC Power Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".

Tags
You have subscribed to this tag. To view or manage your tag subscriptions, click here.   Close
You have unsubscribed from this tag. To view or manage your tag subscriptions, click here.   Close
You are currently viewing:
buck
Related Posts

  • Forum Post: UCC3889 transformer design

    Edward Mulder
    Hi, We are working on a design which uses the UCC3889 step down converter. The circuit as described in application note U-149 performs well with a standard coil. The design of the coil is not further specified however. When we constructed our own transformer, the IC burned out. Any more details...
    on May 24, 2011

  • Forum Post: design Non-Isolated buck converter with uc3843

    Jack.Leung
    I have designed a buck converter using UC3843 in the following specification, Vin- 12V to 60V Vout- 10V Iout- 200mA main switch is P type mosfet The problem is, UC3843 how to driver the P-mosfet in this wide input range.. Please help me to develop a proper design using uc3843 for the...
    on Aug 22, 2011

  • Forum Post: LM25119 Switching Regulator 12V configuration is not working

    Prakash Ponnusamy
    Set Input voltage – 12V to 28V Output voltage1 - 5V Output voltage2 - 12V Observed Working fine at No load . If we connect the actual load , Output Voltage is dropped to 3.5V(Instead of 5V) and 1.2V(Instead of 12V) . So we tried with various options and did component changes as much as...
    on May 21, 2012

  • Forum Post: TPS55010 power consumption issue with custom transformer

    Peter Isza
    Hi all, I am trying to use TPS55010EVM-009 with a custom transformer. I need 50mA output @ 5V. My problem is that the circuit consumes 60mA with no load, compared to 10mA with the original transformer. However, it still works, and I can get my 50mA @ 5V, but then the input supply goes up to 110mA ...
    on Dec 1, 2012

  • Forum Post: ISOLATED DC TO DC

    DIOCORIS SOSA
    Hi all, Im new switching regulators. I found a design that uses a flyback topology with a UCC 3801 PWM controller. It is stepping the voltage down to 12v from 600v DC. My problem is that this converter drives a 12v Siren that drains about 1.2A and it only works from 450 -700v range, and I want it to...
    on Jan 2, 2013

  • Forum Post: UCC35702 - maximum duty cycle

    Wm Blum
    Working on an implementation of UCC35702D as a off-line buck convertor. Having issues with achieving 99% duty cycle. 1. Output level is controlled by introducing voltage to the VSclamp pin. I can control VSclamp from 0 to 3V. 2. FB pin is connected to Vref via a 1K resistor. FB sits at 4.90V. 3...
    on Feb 13, 2013

  • Forum Post: LM34922 Design

    Mayur Sutariya
    Hi, I am using LM34922in my new design. LM34922 is pretty new device from TI and datasheet also have limited application notes for design calculations. Did anybody have used this part or done design calculations? I am specially interested for input/output capacitor, Freewheeling diode and thermal...
    on May 1, 2013

  • Forum Post: TPS65251 Design

    Mayur Sutariya
    Hi, I am using a TPS65251 device for generating 3 different supply voltages. i.e. Buchk1 - 3V3, Buck2 - 1V1 and Buck3 - 5V TPS65251 has single POWERGOOD pin which goes low if any of the buck's output is lower then threshold. Now I want my Buck3 output inductor as NO MOUNT in some of the PCBs...
    on May 3, 2013

  • Forum Post: Variable Phase-Shifted Full-Bridge PWM Controller (LM5046/UCC28950)

    David Backus
    Hello, we are looking for a variable Phase-Shifted Full-Bridge Controller (With Synchronous Rectification) to create a variable DC-DC converter. The LM5046 & UCC28950 controllers have the majority of the features except the ability to directly control by a micro (TMS320F28035/ UCD3138 ). Does TI...
    on May 8, 2013

All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version)

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2013 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy Policy | Terms of Use