This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: BQ51013B
Recently I developed a system that uses wireless power transfer to charge a battery. Therefor I'm using the BQ500212A on TX side and the BQ51013B at RX side. Both been proven good.
I originally designed the RX side with a ABRACON AWCCA38R32H09C01B coil. Which works perfectly with the TX reference design kit with the BQ500212A and my own design TX station. Once implemented in our application the distance between TX and RX is a bit critical, lets say charging starts from 4 mm and both enclosures have a wall thickness of 2mm. The is some self adhesive tape between the enclosure and the coils. And in some cases no energy is transferred.To resolve this problem I though to used another coil wich fits better with the TX coil (WE 760308101103). The one I selected is WE 760308103205, I threw these value's in my calculation sheet to calculate new values for C1 and C2 (in ref with datasheet of the BQ51013B). I replaced those capacitors on my board, did a quick test, and to my surprise the system is not working at all. I looked to RECT with my scope and the induced voltage way above 2,7V. So I was expecting it would start transferring energy.
My TX side schematic
My RX side schematic
RECT on RX side:
Bill Johns, Applications Engineer
Texas Instruments Inc
Please click "This resolved my issue" button if this post answers your question.
In reply to Bill Johns:
Thank you for accepting my post. In meanwhile I took a few more scope captures. This time I used the correct function to export, so X and Y scale are present.
I measured the COM+ at TX side. This does not go bellow 0V. DC offset is 1,5V and a package is modulated on it.
At receiving side I stacked 33nF on top of the 22nF capacitor. Apparently I'm out of 47 and 68nF capacitors SMD0603. So I'm not really 68nF, but getting close. However, this does no seem help very much.
RECT at RX with 22+33nF
COM+ at TX side
In reply to Mathieu Hebbrecht96:
So long story short. There were actually two issue's. Both were not related to each other but by coincidence they seemed not to work anymore.
The Tx side I was using suffered from a few reworks in the past and a wire connecting the DPWM-1A signal to the H-brige was broken loose, and probably it worked unstable. Repaired the board and energy transfer was a success. Unfortunately there was nog significant increase in the distance between the to coils for initiating energy transfer.
So I took another Rx board and attached yet another Qi Rx coil (WE 760308101303). On the WE website there is a note in the compliancy column, 'works with Qi Rx IC’s'. So it's not really Qi compliant but it should work. I have no ambition to certify my unit, so Qi or not. Don't care. But I want to increase the distance between my two modules so I'm trying to improve the EM coupling between the two, and this one might do the trick.Unfortunately I doesn't, there is no energy transfer at al. While other two coils work perfectly. So I assume there is an issue with the capacitance (to low or to high), according to my calculations with some tolerance included it should work. What is best practice to counter this issue? Where should I watch the signal to see what is going on. How can I judge to increase or decrease, or is it really try and error?
Another question I'd like to ask is. What is the best way to increase the distance between the two? On one Rx board I changed C109 and C110 (the COMM1/2 capacitors) to 68nF. In my opinion that has a positive effect on the distance between the two. Can you confirm that?
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.