TI E2E Community
RF & Digital Radio
Welcome to the RF & Digital Radio Section of the TI E2E Support Community. Ask questions, share knowledge, explore ideas, and help solve problems with fellow engineers. To post a question, click on the forum tab then "New Post".
To post a question select the type of RF product you are asking about from the table on the top left and then click new post.
About Zigbee Protocol
who can tell me zigbee mesh network (mesh) routing protocol for that? Is it AODV?
Sombody Help me!
I have trouble, in application of CC1020.
When I change stage to Receive mode, then data signal is apeared on the DIO pin, eventhough I short Ant pin to Ground.
How is it possible?
I use 3 days to solve this problem, but I still not solve it.
My Init Sequence is,
and the Config data is,
0x0F, // 0x01, INTERFACE
0xFF, // 0x02, RESET
0x8F, // 0x03, SEQUENCING
0x3A, // 0x04, FREQ_2A
0x14, // 0x05, FREQ_1A
0x99, // 0x06, FREQ_0A
0x3A, // 0x07, CLOCK_A
0x3A, // 0x08, FREQ_2B
0x1F, // 0x09, FREQ_1B
0x45, // 0x0A, FREQ_0B
0x3A, // 0x0B, CLOCK_B
0x44, // 0x0C, VCO
0x51, // 0x0D, MODEM
0x9B, // 0x0E, DEVIATION
0xC6, // 0x0F, AFC_CONTROL
0x2F, // 0x10, FILTER
0x61, // 0x11, VGA1
0x55, // 0x12, VGA2
0x2f, // 0x13, VGA3
0x2d, // 0x14, VGA4
0x20, // 0x15, LOCK
0x78, // 0x16, FRONTEND
0x47, // 0x17, ANALOG, RX=47/TX=47
0x14, // 0x18, BUFF_SWING
0x22, // 0x19, BUFF_CURRENT
0xAE, // 0x1A, PLL_BW
0x34, // 0x1B, CALIBRATE
0xF0, // 0x1C, PA_POWER
0x00, // 0x1D, MATCH
0x00, // 0x1E, PHASE_COMP
0x00, // 0x1F, GAIN_COMP
0x00 // 0x20, POWERDOWN
I don't understand Why the Signal is appear on the DIO pin, without input signal.
Please somebody help me.
the CC85XXDK contains the parts:
is is possible to get/bye only the CC85XX-CC2590EM (or CC85XXEM) without the complete CC85XXDK
We have a product using the CC2530.The SPI interface of CC2530 connection external FLASH. CC2530 is the SPI master. Use USART1 the alternative1. Hardware connections are as follows. Test found that there is no clock signal output P0.3. When modified to use USART0 of the alternative1, test P0.5, The CC2530 have clock output. Why? If the special requirements of IC, Why did not the notation description in the specification?
About cc2530 spi master
I tried to install the TRF7960 usb drivers unsuccessfully even following the SLOU1892C.
I'm running windows 7 ultimate.
The software is telling me this error: "invalid entry" even if I try to select the right com port.
I verified the com port and it's seem ok.
I tried to have some answers on E2E community but nothing regarding my problem.
Could you help me on this issue?
i need to design a RF remote control swith (to switch ON/OFF network power supply 230v for lighting lamp.
I would like to detail description about the interface between this two RF kits and DSP kit
transmitter TSW3003EVM-RF Transmit Chain Demonstration Kit
Receiver TRF3710EVM Evaluation Module
My qüestion is about the cc2540 and its development kit. I have a doubt in the schematics design that appears in the document SWRR071. There are 2 inductors between the chip and the antena (ref. 251 and 261), that seem to have a value of 2.0nF in the schematic, but in the components boom they have a value of 2.2nF. Which is the correct value for this components the one that apperas in the schematic, the one that appears in the boom or both?
Thanks for the answer!
CC2591 bias inductor tolerance
AN068 (swra236a.pdf), Section 5.2.
I believe the capacitors should be in series with the resistors in the differential to single-ended realization.
Figure 5, and the whole section assumes the capacitors in shunt configuration. Is this an error?
I purchased CC-6LOWPAN-DK-868 last week. I followed the steps according to CC-6LOWPAN-DK-868 Quick Start Guide and User's Guide. but in step 4(as mention in Quick start Guide) I can't see ipv6 router and only see the error message "No connection to /2001:0:0:0:0:0:11".
I can see "PHY: 1:00 - Link is Up - 100/Full" using hyperterminal and also found address 2001::22 under "Local Area Connection" when I use Dos command "netsh interface ipv6 show address".
Here my machine is installed Window 7 Enterprise.
Anybody, can you help me why my machine can't get ethernet connection with edge router.
I have a SimpliciTI project running well on CCS v4.Now when I migrate the project on CCSv5 I have some errors. It cannot resolve the symbol MAX_APP_PAYLOAD located in one configuration file. Also when I attempt to change some parameter in the Porject properties Window, the system tells me to look for details of an error in the project.log file.
I have the following message in this file
: !ERROR: Build-tools MSP430v3.2.1, or any version compatible with it, is not currently installed! Please migrate the project to one of the supported build-tools first.
Could someone help me to resolve this problem.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.