LM35: Land Pattern Example

Kenichiro

Part Number: LM35

[ LM35DT/NOPB ] Land Pattern Example

Hi,

Can you please send me a recommended land pattern with pdf file?
I have tried to convert bxl file to CAD file based on the reference posts below, however my UL cannot do the job, since it's free version.

Thank you for your support in advance.
Regards,
Ken

Other Reference Posts

LM35: LM35DT/NOPB Footprint
e2e.ti.com/.../615207

LM35: Anyone got TDS for TO-220 package size?
e2e.ti.com/.../2176059

over 6 years ago

0 Kelvin Le THS over 6 years ago

TI__Expert 6475 points

Hi Kenichiro,

Let me check for it.

-Kelvin

0 Aaron Heng over 6 years ago in reply to Kelvin Le THS

TI__Mastermind 31600 points

Hi Ken,

I'm sorry that you are unable to convert to your CAD software. Unforunately, the draft team is still working on this. I will try to expedite this and back to you soon.

Aaron

0 Kenichiro over 6 years ago in reply to Aaron Heng

Mastermind 9165 points

Hi Kelvin, Arron,

Thank you for your support.
I'm looking forward to hearing update from your side!

Regards,
Ken

0 Aaron Heng over 6 years ago in reply to Kenichiro

TI__Mastermind 31600 points

Hi Ken,

Just want to provide you some update. The drafting team will provide me a preliminary drawing by next Wednesday for my review. I will keep you posted.

Aaron

0 Kenichiro over 6 years ago in reply to Aaron Heng

Mastermind 9165 points

Aaron,

Thank you for sharing the progress!
I will share the situation with my customer!

BTW, that drawing will be included in the datasheet later on, correct?

Thanks,
Ken

0 Aaron Heng over 6 years ago in reply to Kenichiro

TI__Mastermind 31600 points

Hi Ken,

Yes once I approved the final drawing. It will automatically attach to the datasheet.

Aaron

0 Aaron Heng over 6 years ago in reply to Aaron Heng

TI__Mastermind 31600 points

Hi Ken,

Attached is a preliminary drawing. I reviewed the drawing. Everything looks good except the diameter of the hole. Please do look out for the final drawing publish on LM35 datasheet. I will let you know as soon as I get the confirmation.

3438.NEB0003A_4215013_NR_171120.pdf

Aaron

0 Kenichiro over 6 years ago in reply to Aaron Heng

Mastermind 9165 points

Hi Aaron,

Thank you so much for your support.
I will share this with customer as draft and refer final version once it will be available.

It looks okay to me, though. Which diameter of the hole is not valid? How should it be?

Thanks,
Ken

0 Aaron Heng over 6 years ago in reply to Kenichiro

TI__Mastermind 31600 points

Hi Ken,

Please hold off from sharing the landing pattern information. I will send you the latest drawing once I confirmed with packaging group. I'm sorry for the confusion.

Aaron

0 Kenichiro over 6 years ago in reply to Aaron Heng

Mastermind 9165 points

Sure, Aaron,

I wait for further update from you!

Regards,
Ken

0 Aaron Heng over 6 years ago in reply to Kenichiro

TI__Mastermind 31600 points

Hi Ken,

Attached is the drawing that I approved. I don't recall that we have the LM35 with 90° angle bend on the pin. We normally carry the through hole straight leads forming. Could you please confirm with customer what they have? This Thursday and Friday is the Thanksgiving Holiday in the US. Most people are out for time off. Hopefully, I can get it publish by early next week.

NEB0003F_422XXXX_NR_171122.pdf

Aaron

0 Kenichiro over 6 years ago in reply to Aaron Heng

Mastermind 9165 points

Hi Aaron,

Thank you so much for following up!
I have shared new drawing with my customer!

Regards,
Ken

Sensors

Sensors forum

LM35: Land Pattern Example

[ LM35DT/NOPB ] Land Pattern Example