OAD setup error

Kumar Karan Jain

Other Parts Discussed in Thread: CC2541, BLE-STACK

Hii,

I am evaluating OAD feature with cc2541 mini development kit, referring to OAD_for_CC254x.pdf.

Follows step 10 exactly.Alter last point when tap on Rebuild All got following error :-

Error[e12]: Unable to open file 'C:\Texas Instruments\BLE-CC254x-1.4.0\Projects\ble\SimpleBLEPeripheral\CC2541DB\..\..\common\CC2541\cc254x_f256_imgA.xcl' .

Please help me to resolve this issue.

I hope I make my point clear.

Thanks,

Kumar Karan Jain

over 8 years ago

0 YiKai Chen over 8 years ago

Guru 735455 points

There are default OAD project in SimpleBLEPeripheral workspace. You can try to build it and see if you have the same problem.

0 Kumar Karan Jain over 8 years ago in reply to YiKai Chen

Intellectual 860 points

Thanks for your reply YK Chen.

I didn't find any such example.I am using BLE-CC254x-1.4.0.

There are only options below Workspace is written :-
1) CC2541-DKmini Keyfob
2)CC2541
and 3rd is shown after following step 10 in OAD_for_cc2541x.pdf. i.e CC2541-OAD-ImgA.

Please help!

0 YiKai Chen over 8 years ago in reply to Kumar Karan Jain

Guru 735455 points

I use BLE-STACK 1.4.0. You can try the attached project files.

SimpleBLEPeripheral.rar

0 Kumar Karan Jain over 8 years ago in reply to YiKai Chen

Intellectual 860 points

I tried with program suggested by you, but following problem occurs :-
[Su007]: Unable to open the command file "C:\Texas Instruments\BLE-CC254x-1.4.0\Projects\ble\SimpleBLEPeripheral\..\..\config\buildComponents.cfg"
Error while running C/C++ Compiler
simplekeys.c
[Su007]: Unable to open the command file "C:\Texas Instruments\BLE-CC254x-1.4.0\Projects\ble\SimpleBLEPeripheral\..\..\config\buildComponents.cfg"
Error while running C/C++ Compiler .

There were similar 33 problems.

Please suggest !

0 YiKai Chen over 8 years ago in reply to Kumar Karan Jain

Guru 735455 points

Do you use SimpleBLEPeripheral.eww in C:\Texas Instruments\BLE-CC254x-1.4.0\Projects\ble\SimpleBLEPeripheral\CC2541DB? I just remove BLE stack 1.4.0 and install it to test. There is no such errors. I would suggest you to remove BLE stack 1.4.0 and install it to test again.

0 Kumar Karan Jain over 8 years ago in reply to YiKai Chen

Intellectual 860 points

Yes,I'm using SmpleBLEPeripheral.eww. I think the file you send me i.e. SimpleBLEPeripheral.rar is missing with some important config files and folder.

Can you please make it again.

0 YiKai Chen over 8 years ago in reply to Kumar Karan Jain

Guru 735455 points

As I told you, I remove the whole BLE Stack 1.4.0 and install it again. There is no problem to build it.

0 Kumar Karan Jain over 8 years ago in reply to YiKai Chen

Intellectual 860 points

I have also done the same, first remove it and then install it, and It is working well with default SimpleBLEPeripharal but When I tried it with the file send by you I.e. It shows

error there.

I found that there are few files are missing in SimpleBLEPeripheral.rar as compare to default files in SimpleBLEPeripheral.

Please send me that file agiain with all config files.

0 YiKai Chen over 8 years ago in reply to Kumar Karan Jain

Guru 735455 points

If you remove and reinstall BLE stack, you don't have to use my attached project files. You can use the default OAD projects in SimpleBLEPeripharal workspace.

0 Kumar Karan Jain over 8 years ago in reply to Kumar Karan Jain

Intellectual 860 points

Thankyou. Now there is no error while compling.

thanks once again.

Now, I have installed BIM to keyfob and then SimpleBLEPeripheral with CC2541-OAD-ImgA.
Now how can I upload image over the air to keyfob.

Please help me, Thanks for your co-operation.

0 YiKai Chen over 8 years ago in reply to Kumar Karan Jain

Guru 735455 points

You can refer to
e2e.ti.com/.../238079
e2e.ti.com/.../273347

0 JXS over 8 years ago in reply to YiKai Chen

TI__Guru** 105180 points

Thanks YK!

0 YiKai Chen over 8 years ago in reply to JXS

Guru 735455 points

You are welcome.

Bluetooth®︎

Bluetooth forum

OAD setup error