x_idle_ns: 19112604462750000 ns [ 0.313366] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.318356] pinctrl core: initialized pinctrl subsystem [ 0.319228] NET: Registered protocol family 16 [ 0.320209] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.350245] cpuidle: using governor ladder [ 0.380268] cpuidle: using governor menu [ 0.388806] OMAP GPIO hardware version 0.1 [ 0.392757] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@140 0 ! [ 0.408187] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.408200] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.417300] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.417310] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.417775] omap4_sram_init:Unable to allocate sram needed to handle errata I 688 [ 0.417785] omap4_sram_init:Unable to get sram pool needed to handle errata I 688 [ 0.418357] OMAP DMA hardware revision 0.0 [ 0.461477] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver ( LinkedList1/2/3 supported) [ 0.462615] edma 43300000.edma: memcpy is disabled [ 0.467324] edma 43300000.edma: TI EDMA DMA engine driver [ 0.471405] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.471589] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.471747] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.471906] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.472180] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.472385] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.475419] palmas 0-0058: IRQ missing: skipping irq request [ 0.490857] palmas 0-0058: Muxing GPIO 2e, PWM 0, LED 0 [ 0.552732] pcf857x: probe of 0-0020 failed with error -121 [ 0.552984] pcf857x: probe of 0-0021 failed with error -121 [ 0.553841] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.554254] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.554451] media: Linux media interface: v0.10 [ 0.554503] Linux video capture interface: v2.00 [ 0.554545] pps_core: LinuxPPS API ver. 1 registered [ 0.554552] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.554581] PTP clock support registered [ 0.554631] EDAC MC: Ver: 3.0.0 [ 0.555380] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.555672] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.556002] Advanced Linux Sound Architecture Driver Initialized. [ 0.556867] clocksource: Switched to clocksource arch_sys_counter [ 0.567428] NET: Registered protocol family 2 [ 0.567930] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.567994] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.568119] TCP: Hash tables configured (established 8192 bind 8192) [ 0.568165] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.568196] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.568336] NET: Registered protocol family 1 [ 0.568643] RPC: Registered named UNIX socket transport module. [ 0.568652] RPC: Registered udp transport module. [ 0.568659] RPC: Registered tcp transport module. [ 0.568665] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.569625] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counte rs available [ 0.579665] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580310] NFS: Registering the id_resolver key type [ 0.580347] Key type id_resolver registered [ 0.580355] Key type id_legacy registered [ 0.580413] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.581690] bounce: pool size: 64 pages [ 0.581847] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 0.581863] io scheduler noop registered [ 0.581875] io scheduler deadline registered [ 0.581909] io scheduler cfq registered (default) [ 0.587390] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.590919] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges: [ 0.590931] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus 00-ff] [ 0.590964] IO 0x20003000..0x20012fff -> 0x00000000 [ 0.590985] MEM 0x20013000..0x2fffffff -> 0x20013000 [ 0.591194] dra7-pcie 51000000.pcie_rc: CFG 'Bus Master Enable' change [ 0.591204] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617693] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00 [ 0.617706] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.617717] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.617726] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 0.617788] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617804] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617829] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617843] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617867] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617882] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.618183] PCI: bus0: Fast back to back transfers disabled [ 0.636956] PCI: bus1: Fast back to back transfers disabled [ 0.637083] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.637098] pci 0000:00:00.0: BAR 8: assigned [mem 0x20200000-0x202fffff] [ 0.637109] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 0.637123] pci 0000:01:00.0: BAR 0: assigned [mem 0x20200000-0x20203fff 64bi t] [ 0.637170] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.637183] pci 0000:00:00.0: bridge window [mem 0x20200000-0x202fffff] [ 0.637397] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.637407] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 0.698860] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.702244] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 202, base_baud = 3000000) is a 8250 [ 1.802190] console [ttyS0] enabled [ 1.806586] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 203, base_baud = 3000000) is a 8250 [ 1.816288] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 204, base_baud = 3000000) is a 8250 [ 1.826318] [drm] Initialized drm 1.1.0 20060810 [ 1.831876] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.838565] [drm] No driver support for vblank timestamp query. [ 1.844692] [drm] Initialized vdrm 1.0.0 20110917 on minor 0 [ 1.851860] OMAP DSS rev 6.1 [ 1.855615] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_compone nt_ops) [ 1.871227] loop: module loaded [ 1.874762] vmemexp device MAJOR num = 245 [ 1.878913] vmemexp class registered [ 1.882626] /dev/vmemexp device registered [ 1.886741] ioctl DBUFIOC_EXPORT_VIRTMEM = -1072899120 [ 1.892288] nvme 0000:01:00.0: enabling device (0140 -> 0142) [ 1.898715] nand: No NAND device found [ 1.902485] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.911582] m25p80 spi32766.0: found n25q00, expected s25fl256s1 [ 1.917707] m25p80 spi32766.0: n25q00 (131072 Kbytes) [ 1.922839] 7 ofpart partitions found on MTD device spi32766.0 [ 1.928717] Creating 7 MTD partitions on "spi32766.0": [ 1.933879] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.940011] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.956324] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.973298] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.989986] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 2.007404] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 2.019682] nvme0n1: p1 [ 2.023773] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 2.041652] libphy: Fixed MDIO Bus: probed [ 2.096900] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 2.103026] libphy: 48485000.mdio: probed [ 2.120144] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driv er TI DP83867 [ 2.129090] cpsw 48484000.ethernet: Detected MACID = 78:db:2f:4d:21:9a [ 2.135740] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 2.142713] cpsw 48484000.ethernet: cpsw: Detected MACID = 78:db:2f:4d:21:9b [ 2.151329] mousedev: PS/2 mouse device common for all mice [ 2.167536] i2c /dev entries driver [ 2.176283] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.227450] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.233838] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.247014] evm_3v3_sw: supplied by sysen1 [ 2.307711] ledtrig-cpu: registered to indicate activity on CPUs [ 2.317798] aic_dvdd: supplied by evm_3v3_sw [ 2.323022] davinci-mcasp 4847c000.mcasp: invalid tdm slots: 0 [ 2.330527] NET: Registered protocol family 10 [ 2.345836] sit: IPv6 over IPv4 tunneling driver [ 2.351045] NET: Registered protocol family 17 [ 2.355721] Key type dns_resolver registered [ 2.360168] omap_voltage_late_init: Voltage driver support not added [ 2.367074] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.373284] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.379995] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.386204] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.393546] Power Management for TI OMAP4+ devices. [ 2.398679] Registering SWP/SWPB emulation handler [ 2.404801] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.412356] dmm 4e000000.dmm: initialized all PAT entries [ 2.418788] [drm] Initialized omapdrm 1.0.0 20110917 on minor 1 [ 2.436629] hctosys: unable to open rtc device (rtc0) [ 2.453713] evm_1v8: disabling [ 2.456790] aic_dvdd: disabling [ 2.460153] ldousb: disabling [ 2.463637] ALSA device list: [ 2.466617] No soundcards found. [ 2.470919] Waiting for root device PARTUUID=3cc717e1-02... [ 2.486266] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 2.497800] mmc0: new high speed SDHC card at address aaaa [ 2.503776] mmcblk0: mmc0:aaaa SL08G 7.40 GiB [ 2.509579] mmcblk0: p1 p2 [ 2.577521] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incomp atibilities [ 2.586183] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incomp atibilities [ 2.620163] EXT4-fs (mmcblk0p2): recovery complete [ 2.624986] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 2.633179] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.641438] devtmpfs: mounted [ 2.644630] Freeing unused kernel memory: 336K [ 2.649185] This architecture does not have kernel memory protection. [ 2.863395] systemd[1]: System time before build time, advancing clock. [ 2.904545] random: systemd: uninitialized urandom read (16 bytes read, 12 bi ts of entropy available) [ 2.917908] random: systemd: uninitialized urandom read (16 bytes read, 12 bi ts of entropy available) [ 2.929538] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SEL INUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL + XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 2.948040] systemd[1]: Detected architecture arm. Welcome to Arago 2016.12! [ 2.977994] systemd[1]: Set hostname to . [ 3.040639] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 13 bits of entropy available) [ 3.076459] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 14 bits of entropy available) [ 3.086915] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 14 bits of entropy available) [ 3.097192] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 14 bits of entropy available) [ 3.110542] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 14 bits of entropy available) [ 3.199563] random: systemd: uninitialized urandom read (16 bytes read, 17 bi ts of entropy available) [ 3.209157] random: systemd: uninitialized urandom read (16 bytes read, 17 bi ts of entropy available) [ 3.219141] random: systemd: uninitialized urandom read (16 bytes read, 17 bi ts of entropy available) [ 3.497458] systemd[1]: Configuration file /etc/systemd/system/multi-user.tar get.wants/vsdk.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.514771] systemd[1]: [/etc/systemd/system/multi-user.target.wants/vsdk.ser vice:3] Failed to add dependency on rc.pvr, ignoring: Invalid argument [ 3.615419] systemd[1]: sockets.target: Found ordering cycle on sockets.targe t/start [ 3.623309] systemd[1]: sockets.target: Found dependency on dropbear.socket/s top [ 3.630789] systemd[1]: sockets.target: Found dependency on sysinit.target/st art [ 3.638293] systemd[1]: sockets.target: Found dependency on alignment.service /start [ 3.645988] systemd[1]: sockets.target: Found dependency on basic.target/star t [ 3.653263] systemd[1]: sockets.target: Found dependency on sockets.target/st art [ 3.660713] systemd[1]: sockets.target: Breaking ordering cycle by deleting j ob dropbear.socket/stop [ 3.670811] systemd[1]: dropbear.socket: Job dropbear.socket/stop deleted to break ordering cycle starting with sockets.target/start [ SKIP ] Ordering cycle found, skipping dropbear.socket [ 3.697128] systemd[1]: dbus.socket: Found ordering cycle on dbus.socket/star t [ 3.704391] systemd[1]: dbus.socket: Found dependency on sysinit.target/start [ 3.711654] systemd[1]: dbus.socket: Found dependency on alignment.service/st art [ 3.719136] systemd[1]: dbus.socket: Found dependency on basic.target/start [ 3.726133] systemd[1]: dbus.socket: Found dependency on sockets.target/start [ 3.733345] systemd[1]: dbus.socket: Found dependency on dbus.socket/start [ 3.740309] systemd[1]: dbus.socket: Breaking ordering cycle by deleting job alignment.service/start [ 3.749509] systemd[1]: alignment.service: Job alignment.service/start delete d to break ordering cycle starting with dbus.socket/start [ SKIP ] Ordering cycle found, skipping alignment.service [ 3.789246] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 3.817269] systemd[1]: Started Forward Password Requests to Wall Directory W atch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 3.848509] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 3.877230] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 3.907072] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 3.927158] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.957736] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 3.987292] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 4.017703] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 4.047058] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 4.067106] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 4.097718] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 4.137613] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 4.167364] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 4.227303] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 4.259565] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 4.276502] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 4.291613] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 4.319550] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 4.341079] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 4.349782] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 4.417088] systemd[1]: Mounting Temporary Directory... Mounting Temporary Directory... [ 4.447247] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 4.507265] systemd[1]: Starting Journal Service... Starting Journal Service... [ 4.537365] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 4.567183] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 4.622696] systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. [ 4.647201] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 4.677140] systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. [ 4.707383] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Setup Virtual Console. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create list of required sta...ce nodes for the current kernel. Starting Create Static Device Nodes in /dev... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ 5.429552] systemd-journald[148]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Mounting /media/ram... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Load/Save Random Seed. [ 6.076795] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@9 5800000 [ 6.118279] remoteproc0: 55020000.ipu is available [ 6.139133] remoteproc0: Note: remoteproc is still under development and con sidered experimental. [ 6.158698] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started udev Coldplug all Devices.[ 6.220855] omap-rproc 40800000.ds p: assigned reserved memory node dsp1_cma@99000000 [ 6.307698] remoteproc1: 40800000.dsp is available [ 6.312611] remoteproc1: Note: remoteproc is still under development and con sidered experimental. [ 6.366765] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.398081] remoteproc1: Direct firmware load for dra7-dsp1-fw.xe66 failed w ith error -2 [ 6.408978] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9 f000000 [ 6.416933] remoteproc1: failed to load dra7-dsp1-fw.xe66 [ 6.433159] remoteproc2: 41000000.dsp is available [ 6.433164] remoteproc2: Note: remoteproc is still under development and con sidered experimental. [ 6.433167] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.433287] remoteproc2: Direct firmware load for dra7-dsp2-fw.xe66 failed w ith error -2 [ 6.433294] remoteproc2: failed to load dra7-dsp2-fw.xe66 [ 6.469133] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 6.538001] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20 [ 6.580542] remoteproc0: registered virtio0 (type 7) [ 6.630331] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0 [ OK ] Found device /dev/ttyS0. [ 6.882191] SCSI subsystem initialized [ 6.917703] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 6.960962] CAN device driver interface [ 7.005647] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 7.066118] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 7.097791] c_can_platform 4ae3c000.can: c_can_platform device registered (re gs=fce3c000, irq=254) [ OK ] Started Network Time Synchronization. [ OK ] Started Update UTMP about System Boot/Shutdown. [ 7.405246] [drm] Initialized pvr 1.14.3699939 20110701 on minor 2 [ 7.427473] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 7.448779] ahci 4a140000.sata: Enable 32-bit DMA instead of 64-bit. [ 7.479861] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 im pl platform mode [ 7.530176] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pm p pio slum part ccc apst [ 7.604378] scsi host0: ahci [ 7.617638] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x1 00 irq 240 Starting Synchronize System and HW clocks... [ OK ] Reached target System Time Synchronized. [ OK ] Started Synchronize System and HW clocks. [ 7.985137] EXT4-fs (nvme0n1p1): recovery complete [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.[ 7.9 99838] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. Opts: (nu ll) [ 8.008334] ata1: SATA link down (SStatus 0 SControl 300) [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ 8.057294] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. Starting Network Service... [ 8.417611] remoteproc0: powering up 55020000.ipu [ 8.438218] remoteproc0: Booting fw image dra7-ipu2-fw.xem4, size 4396172 [ 8.451680] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1 [ OK ] Started Kernel Logging Service. [ 8.485722] net eth0: initializing cpsw version 1.15 (0) [ 8.503442] net eth0: initialized cpsw ale version 1.4 [ 8.512508] net eth0: ALE Table size 1024 [ OK ] Started System Logging Service. [ 8.533529] net eth0: phy found : id is : 0x2000a231 Starting rc.pvr.service...[ 8.553757] remoteproc0: remote processor 55020000.ipu is now up [ 8.557813] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.581593] virtio_rpmsg_bus virtio0: rpmsg host is online [ OK ] Started Launching Vision SDK App. [ 8.604504] virtio_rpmsg_bus virtio0: creating channel rpmsg-proto addr 0x50 Starting Login Service... [ 8.632500] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] [ 8.678180] NET: Registered protocol family 41 [ OK ] Started Permit User Sessions. [ OK ] Started Network Service. [ OK ] Started rc.pvr.service. [ OK ] Started Login Service. Starting LSB: Dropbear Secure Shell server... Starting weston.service... Starting Network Service... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started weston.service. [ OK ] Started Network Service. Starting Network Service... Starting tiipclad-daemon.service... Starting telnetd.service... [ OK ] Started Network Service. [ OK ] Started tiipclad-daemon.service. [ OK ] Started telnetd.service. Starting Network Service... [ OK ] Started Network Service. Starting Network Service... [ OK ] Started Network Service. [FAILED] Failed to listen on Network Service Bus Name. See 'systemctl status org.freedesktop.network1.busname' for details. [FAILED] Failed to start Network Service. See 'systemctl status systemd-networkd.service' for details. [ OK ] Reached target Network. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ 13.861041] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. O pts: (null) _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dra7xx-evm ttyS0 Arago 2016.12 dra7xx-evm ttyS0 dra7xx-evm login: [ 15.902241] DMA: Module install successful, device major nu m = 241 [ 15.912808] DRV: Module install successful [ 16.174868] omap_l3_noc 44000000.ocp: L3 application error: target 3 mod:2 (u nclearable) [ 16.183037] omap_l3_noc 44000000.ocp: L3 debug error: target 3 mod:2 (unclear able) [ 29.578649] random: nonblocking pool is initialized U-Boot SPL 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... spl: falcon_args_file not set in environment, falling back to default reading single-stage-boot.dtb spl_load_image_fat_os: error reading image single-stage-boot.dtb, err - -1 reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03 +0530) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x Cascade EVM REV H.4 DRAM: 4 GiB MMC: i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 OMAP SD/MMC: 0, OMAP SD/MMC: 1 Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Card did not respond to voltage select! ERROR: invalid mmc device at arch/arm/cpu/armv7/omap-common/utils.c:193/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 2 Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 ## Error: "board_findfdt" not defined i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 185 bytes read in 2 ms (89.8 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 3577032 bytes read in 176 ms (19.4 MiB/s) 107792 bytes read in 27 ms (3.8 MiB/s) Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x3694c8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe2000, end 8ffff50f ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.84-00041-g84382ab (x0284921@bangvideoapps02) (g cc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Mon Aug 5 14 :52:40 IST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 Cascade Radar Board [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000040300000, s ize 3 MiB [ 0.000000] Reserved memory: initialized node cmem@40300000, compatible id sh ared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, s ize 80 MiB [ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009e000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a1000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a3000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9000000, s ize 64 MiB [ 0.000000] Reserved memory: initialized node cmem@A9000000, compatible id sh ared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] cma: Reserved 64 MiB at 0x00000000bc000000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0x000000027fd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @f2f1e000 s14912 r8192 d21952 u4505 6 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 1025330 [ 0.000000] Kernel command line: console=ttyO0,115200n8 vram=16M root=PARTUUI D=3cc717e1-02 rw rootwait ip=none cma=64M vmalloc=128M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2439424K/4109312K available (6671K kernel code, 320K rwda ta, 2396K rodata, 336K init, 290K bss, 1424128K reserved, 245760K cma-reserved, 2167808K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf8000000 - 0xff800000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf7800000 ( 888 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08e302c (9069 kB) [ 0.000000] .init : 0xc08e4000 - 0xc0938000 ( 336 kB) [ 0.000000] .data : 0xc0938000 - 0xc0988220 ( 321 kB) [ 0.000000] .bss : 0xc098a000 - 0xc09d2880 ( 291 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_ clk_div [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 43980 46511023ns [ 0.000015] Switching to timer-based delay loop, resolution 162ns [ 0.000334] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff , max_idle_ns: 58327039986419 ns [ 0.000342] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000781] Console: colour dummy device 80x30 [ 0.000796] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000803] This ensures that you still see kernel messages. Please [ 0.000808] update your kernel commandline. [ 0.000822] Calibrating delay loop (skipped), value calculated using timer fr equency.. 12.29 BogoMIPS (lpj=61475) [ 0.000834] pid_max: default: 32768 minimum: 301 [ 0.000932] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000943] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001486] Initializing cgroup subsys io [ 0.001502] Initializing cgroup subsys memory [ 0.001527] Initializing cgroup subsys devices [ 0.001539] Initializing cgroup subsys freezer [ 0.001551] Initializing cgroup subsys perf_event [ 0.001562] Initializing cgroup subsys pids [ 0.001589] CPU: Testing write buffer coherency: ok [ 0.001788] /cpus/cpu@0 missing clock-frequency property [ 0.001804] /cpus/cpu@1 missing clock-frequency property [ 0.001814] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001849] Setting up static identity map for 0x80008380 - 0x800083e0 [ 0.080061] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.080129] Brought up 2 CPUs [ 0.080142] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.080147] CPU: All CPU(s) started in HYP mode. [ 0.080153] CPU: Virtualization extensions available. [ 0.080530] devtmpfs: initialized [ 0.109583] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.110570] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.313413] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.313435] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.318620] pinctrl core: initialized pinctrl subsystem [ 0.319500] NET: Registered protocol family 16 [ 0.320469] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.350234] cpuidle: using governor ladder [ 0.380254] cpuidle: using governor menu [ 0.388809] OMAP GPIO hardware version 0.1 [ 0.392752] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@140 0 ! [ 0.408171] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.408184] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.417280] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.417291] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.417764] omap4_sram_init:Unable to allocate sram needed to handle errata I 688 [ 0.417773] omap4_sram_init:Unable to get sram pool needed to handle errata I 688 [ 0.418344] OMAP DMA hardware revision 0.0 [ 0.461462] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver ( LinkedList1/2/3 supported) [ 0.462596] edma 43300000.edma: memcpy is disabled [ 0.467280] edma 43300000.edma: TI EDMA DMA engine driver [ 0.471355] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.471540] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.471697] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.471855] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.472129] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.472330] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.475349] palmas 0-0058: IRQ missing: skipping irq request [ 0.490823] palmas 0-0058: Muxing GPIO 2e, PWM 0, LED 0 [ 0.552701] pcf857x: probe of 0-0020 failed with error -121 [ 0.552949] pcf857x: probe of 0-0021 failed with error -121 [ 0.553807] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.554214] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.554416] media: Linux media interface: v0.10 [ 0.554469] Linux video capture interface: v2.00 [ 0.554509] pps_core: LinuxPPS API ver. 1 registered [ 0.554517] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.554545] PTP clock support registered [ 0.554596] EDAC MC: Ver: 3.0.0 [ 0.555354] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.555644] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.555977] Advanced Linux Sound Architecture Driver Initialized. [ 0.556842] clocksource: Switched to clocksource arch_sys_counter [ 0.567439] NET: Registered protocol family 2 [ 0.567948] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.568011] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.568136] TCP: Hash tables configured (established 8192 bind 8192) [ 0.568182] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.568214] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.568356] NET: Registered protocol family 1 [ 0.568668] RPC: Registered named UNIX socket transport module. [ 0.568677] RPC: Registered udp transport module. [ 0.568684] RPC: Registered tcp transport module. [ 0.568690] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.569670] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counte rs available [ 0.579670] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580319] NFS: Registering the id_resolver key type [ 0.580349] Key type id_resolver registered [ 0.580357] Key type id_legacy registered [ 0.580414] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.581686] bounce: pool size: 64 pages [ 0.581843] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 0.581858] io scheduler noop registered [ 0.581871] io scheduler deadline registered [ 0.581905] io scheduler cfq registered (default) [ 0.587387] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.590891] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges: [ 0.590904] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus 00-ff] [ 0.590936] IO 0x20003000..0x20012fff -> 0x00000000 [ 0.590957] MEM 0x20013000..0x2fffffff -> 0x20013000 [ 0.591168] dra7-pcie 51000000.pcie_rc: CFG 'Bus Master Enable' change [ 0.591178] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617651] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00 [ 0.617665] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.617675] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.617684] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 0.617747] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617763] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617788] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617804] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617827] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617841] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.618139] PCI: bus0: Fast back to back transfers disabled [ 0.636932] PCI: bus1: Fast back to back transfers disabled [ 0.637061] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.637076] pci 0000:00:00.0: BAR 8: assigned [mem 0x20200000-0x202fffff] [ 0.637087] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 0.637101] pci 0000:01:00.0: BAR 0: assigned [mem 0x20200000-0x20203fff 64bi t] [ 0.637150] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.637162] pci 0000:00:00.0: bridge window [mem 0x20200000-0x202fffff] [ 0.637375] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.637384] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 0.699006] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.702406] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 202, base_baud = 3000000) is a 8250 [ 1.802353] console [ttyS0] enabled [ 1.806748] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 203, base_baud = 3000000) is a 8250 [ 1.816451] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 204, base_baud = 3000000) is a 8250 [ 1.826473] [drm] Initialized drm 1.1.0 20060810 [ 1.832029] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.838716] [drm] No driver support for vblank timestamp query. [ 1.844843] [drm] Initialized vdrm 1.0.0 20110917 on minor 0 [ 1.851999] OMAP DSS rev 6.1 [ 1.855736] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_compone nt_ops) [ 1.871340] loop: module loaded [ 1.874876] vmemexp device MAJOR num = 245 [ 1.879028] vmemexp class registered [ 1.882742] /dev/vmemexp device registered [ 1.886875] ioctl DBUFIOC_EXPORT_VIRTMEM = -1072899120 [ 1.892407] nvme 0000:01:00.0: enabling device (0140 -> 0142) [ 1.898828] nand: No NAND device found [ 1.902600] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.911695] m25p80 spi32766.0: found n25q00, expected s25fl256s1 [ 1.917819] m25p80 spi32766.0: n25q00 (131072 Kbytes) [ 1.922951] 7 ofpart partitions found on MTD device spi32766.0 [ 1.928831] Creating 7 MTD partitions on "spi32766.0": [ 1.933995] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.940125] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.956445] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.963388] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.980079] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 1.997461] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 2.009594] nvme0n1: p1 [ 2.013821] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 2.031697] libphy: Fixed MDIO Bus: probed [ 2.086876] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 2.093000] libphy: 48485000.mdio: probed [ 2.099662] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driv er TI DP83867 [ 2.108610] cpsw 48484000.ethernet: Detected MACID = 78:db:2f:4d:21:9a [ 2.115256] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 2.122235] cpsw 48484000.ethernet: cpsw: Detected MACID = 78:db:2f:4d:21:9b [ 2.130871] mousedev: PS/2 mouse device common for all mice [ 2.147088] i2c /dev entries driver [ 2.155836] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.207418] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.213803] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.236986] evm_3v3_sw: supplied by sysen1 [ 2.277686] ledtrig-cpu: registered to indicate activity on CPUs [ 2.287767] aic_dvdd: supplied by evm_3v3_sw [ 2.293001] davinci-mcasp 4847c000.mcasp: invalid tdm slots: 0 [ 2.300515] NET: Registered protocol family 10 [ 2.315831] sit: IPv6 over IPv4 tunneling driver [ 2.321047] NET: Registered protocol family 17 [ 2.325726] Key type dns_resolver registered [ 2.330174] omap_voltage_late_init: Voltage driver support not added [ 2.337080] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.343289] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.350021] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.356228] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.363559] Power Management for TI OMAP4+ devices. [ 2.368690] Registering SWP/SWPB emulation handler [ 2.374824] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.382366] dmm 4e000000.dmm: initialized all PAT entries [ 2.388803] [drm] Initialized omapdrm 1.0.0 20110917 on minor 1 [ 2.397672] hctosys: unable to open rtc device (rtc0) [ 2.414758] evm_1v8: disabling [ 2.417858] aic_dvdd: disabling [ 2.421206] ldousb: disabling [ 2.424671] ALSA device list: [ 2.427673] No soundcards found. [ 2.431972] Waiting for root device PARTUUID=3cc717e1-02... [ 2.466259] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 2.477747] mmc0: new high speed SDHC card at address aaaa [ 2.493737] mmcblk0: mmc0:aaaa SL08G 7.40 GiB [ 2.499549] mmcblk0: p1 p2 [ 2.547474] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incomp atibilities [ 2.556128] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incomp atibilities [ 2.766506] EXT4-fs (mmcblk0p2): recovery complete [ 2.772623] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 2.780793] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.789271] devtmpfs: mounted [ 2.792460] Freeing unused kernel memory: 336K [ 2.797011] This architecture does not have kernel memory protection. [ 2.995485] systemd[1]: System time before build time, advancing clock. [ 3.036979] random: systemd: uninitialized urandom read (16 bytes read, 17 bi ts of entropy available) [ 3.050294] random: systemd: uninitialized urandom read (16 bytes read, 17 bi ts of entropy available) [ 3.061948] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SEL INUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL + XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 3.080469] systemd[1]: Detected architecture arm. Welcome to Arago 2016.12! [ 3.107974] systemd[1]: Set hostname to . [ 3.171373] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 18 bits of entropy available) [ 3.207547] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 19 bits of entropy available) [ 3.217912] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 19 bits of entropy available) [ 3.228203] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 19 bits of entropy available) [ 3.241439] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 19 bits of entropy available) [ 3.332329] random: systemd: uninitialized urandom read (16 bytes read, 22 bi ts of entropy available) [ 3.341932] random: systemd: uninitialized urandom read (16 bytes read, 22 bi ts of entropy available) [ 3.351965] random: systemd: uninitialized urandom read (16 bytes read, 22 bi ts of entropy available) [ 3.634100] systemd[1]: Configuration file /etc/systemd/system/multi-user.tar get.wants/vsdk.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.652291] systemd[1]: [/etc/systemd/system/multi-user.target.wants/vsdk.ser vice:3] Failed to add dependency on rc.pvr, ignoring: Invalid argument [ 3.753394] systemd[1]: sysinit.target: Found ordering cycle on sysinit.targe t/start [ 3.761244] systemd[1]: sysinit.target: Found dependency on alignment.service /start [ 3.769053] systemd[1]: sysinit.target: Found dependency on sysinit.target/st art [ 3.776490] systemd[1]: sysinit.target: Breaking ordering cycle by deleting j ob alignment.service/start [ 3.785971] systemd[1]: alignment.service: Job alignment.service/start delete d to break ordering cycle starting with sysinit.target/start [ SKIP ] Ordering cycle found, skipping alignment.service [ 3.819422] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 3.847166] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 3.868531] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 3.897241] systemd[1]: Started Forward Password Requests to Wall Directory W atch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 3.917287] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 3.947170] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.977057] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 3.997096] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 4.027168] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 4.057064] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 4.087142] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 4.117700] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 4.187104] systemd[1]: Mounting Temporary Directory... Mounting Temporary Directory... [ 4.213228] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 4.237923] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.287259] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 4.317179] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 4.339435] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 4.355638] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 4.368032] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 4.427225] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 4.439467] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 4.477163] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 4.527156] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 4.549565] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 4.582310] systemd[1]: Starting Journal Service... Starting Journal Service... [ 4.641876] systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. [ 4.677227] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 4.707207] systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. [ 4.737347] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Setup Virtual Console. Starting udev Coldplug all Devices... Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ 5.467667] systemd-journald[148]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Mounting /media/ram... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ 5.939292] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@9 5800000 [ 5.964591] remoteproc0: 55020000.ipu is available [ 5.985371] remoteproc0: Note: remoteproc is still under development and con sidered experimental. [ 5.995261] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.014443] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@9 9000000 Starting Load/Save Random Seed... [ 6.054578] remoteproc1: 40800000.dsp is available [ OK ] Reached target Local File Systems. [ 6.073066] remoteproc1: Note: remoteproc is still under development and con sidered experimental. [ 6.093943] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.120158] remoteproc1: Direct firmware load for dra7-dsp1-fw.xe66 failed w ith error -2 [ 6.133572] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9 f000000 [ 6.162581] remoteproc1: failed to load dra7-dsp1-fw.xe66 Starting Create Volatile Files and Directories...[ 6.179035] remote proc2: 41000000.dsp is available [ OK ] Started udev Coldplug all Devices. [ 6.224931] remoteproc2: Note: remoteproc is still under development and con sidered experimental. [ 6.244833] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ OK ] Started Load/Save Random Seed. [ 6.284302] remoteproc2: Direct firmware load for dra7-dsp2-fw.xe66 failed w ith error -2 [ 6.317282] remoteproc2: failed to load dra7-dsp2-fw.xe66 [ 6.318255] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 6.362807] remoteproc0: registered virtio0 (type 7) [ 6.376529] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20 [ OK ] Started Create Volatile Files and Directories. [ OK ] Found device /dev/ttyS0. [ 6.492817] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0 [ 6.708070] SCSI subsystem initialized Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 6.853638] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ OK ] Started Network Time Synchronization.[ 6.868792] omap-aes 4b700000.a es: OMAP AES hw accel rev: 3.3 [ 6.889794] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 6.975957] CAN device driver interface [ OK ] Started Update UTMP about System Boot/Shutdown. [ 7.054158] c_can_platform 4ae3c000.can: c_can_platform device registered (re gs=fce3c000, irq=254) [ 7.092733] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 7.105404] ahci 4a140000.sata: Enable 32-bit DMA instead of 64-bit. Starting Synchronize System and HW clocks... [ 7.154239] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 im pl platform mode [ OK ] Reached target System Time Synchronized. [ 7.189724] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pm p pio slum part ccc apst [ OK ] Started Synchronize System and HW clocks. [ 7.278975] scsi host0: ahci [ 7.282271] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x1 00 irq 240 [ 7.365599] [drm] Initialized pvr 1.14.3699939 20110701 on minor 2 [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on dropbear.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Kernel Logging Service. [ OK ] Started Daily Cleanup of Temporary Directories.[ 7.686985] ata1: SAT A link down (SStatus 0 SControl 300) [ OK ] Reached target Timers. [ 7.752677] EXT4-fs (nvme0n1p1): recovery complete Starting rc.pvr.service... [ 7.775332] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. O pts: (null) Starting Permit User Sessions... [ OK ] Started Launching Vision SDK App. [ 7.903815] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. Starting Login Service... [ 7.938701] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] [ OK ] Started System Logging Service. [ OK ] Started D-Bus System Message Bus. Starting Network Service... [ OK ] Started rc.pvr.service. [ OK ] Started Permit User Sessions. [ 8.405496] net eth0: initializing cpsw version 1.15 (0) [ 8.428662] remoteproc0: powering up 55020000.ipu [ 8.447594] net eth0: initialized cpsw ale version 1.4 [ 8.452766] net eth0: ALE Table size 1024 [ 8.468280] remoteproc0: Booting fw image dra7-ipu2-fw.xem4, size 4396172 [ 8.472607] net eth0: phy found : id is : 0x2000a231 [ 8.480404] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.504662] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1 [ OK ] Started Network Service.[ 8.578331] remoteproc0: remote processor 5 5020000.ipu is now up [ 8.588737] virtio_rpmsg_bus virtio0: rpmsg host is online [ 8.628767] virtio_rpmsg_bus virtio0: creating channel rpmsg-proto addr 0x50 [ 8.656803] NET: Registered protocol family 41 [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting Network Service... [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. Starting weston.service... [ OK ] Started Network Service. [ OK ] Started weston.service. [ OK ] Started Login Service. Starting Network Service... Starting telnetd.service... Starting tiipclad-daemon.service... [ OK ] Started Network Service. [ OK ] Started telnetd.service. [ OK ] Started tiipclad-daemon.service. Starting Network Service... [ OK ] Started Network Service. Starting Network Service... [ OK ] Started Network Service. [FAILED] Failed to listen on Network Service Bus Name. See 'systemctl status org.freedesktop.network1.busname' for details. [FAILED] Failed to start Network Service. See 'systemctl status systemd-networkd.service' for details. [ OK ] Reached target Network. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ 13.119289] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. O pts: (null) [ 15.153127] DMA: Module install successful, device major num = 241 [ 15.159474] DRV: Module install successful _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dra7xx-evm ttyS0 Arago 2016.12 dra7xx-evm ttyS0 dra7xx-evm login: [ 15.428694] omap_l3_noc 44000000.ocp: L3 application error: target 3 mod:2 (unclearable) [ 15.436875] omap_l3_noc 44000000.ocp: L3 debug error: target 3 mod:2 (unclear able) U-Boot SPL 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... spl: falcon_args_file not set in environment, falling back to default reading single-stage-boot.dtb spl_load_image_fat_os: error reading image single-stage-boot.dtb, err - -1 reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03 +0530) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x Cascade EVM REV H.4 DRAM: 4 GiB MMC: i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 OMAP SD/MMC: 0, OMAP SD/MMC: 1 Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Card did not respond to voltage select! ERROR: invalid mmc device at arch/arm/cpu/armv7/omap-common/utils.c:193/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 2 Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 ## Error: "board_findfdt" not defined i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 185 bytes read in 3 ms (59.6 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 3577032 bytes read in 176 ms (19.4 MiB/s) 107792 bytes read in 27 ms (3.8 MiB/s) Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x3694c8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe2000, end 8ffff50f ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.84-00041-g84382ab (x0284921@bangvideoapps02) (g cc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Mon Aug 5 14 :52:40 IST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 Cascade Radar Board [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000040300000, s ize 3 MiB [ 0.000000] Reserved memory: initialized node cmem@40300000, compatible id sh ared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, s ize 80 MiB [ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009e000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a1000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a3000000, s ize 32 MiB [ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible i d shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9000000, s ize 64 MiB [ 0.000000] Reserved memory: initialized node cmem@A9000000, compatible id sh ared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] cma: Reserved 64 MiB at 0x00000000bc000000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0x000000027fd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @f2f1e000 s14912 r8192 d21952 u4505 6 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 1025330 [ 0.000000] Kernel command line: console=ttyO0,115200n8 vram=16M root=PARTUUI D=3cc717e1-02 rw rootwait ip=none cma=64M vmalloc=128M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2439424K/4109312K available (6671K kernel code, 320K rwda ta, 2396K rodata, 336K init, 290K bss, 1424128K reserved, 245760K cma-reserved, 2167808K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf8000000 - 0xff800000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf7800000 ( 888 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08e302c (9069 kB) [ 0.000000] .init : 0xc08e4000 - 0xc0938000 ( 336 kB) [ 0.000000] .data : 0xc0938000 - 0xc0988220 ( 321 kB) [ 0.000000] .bss : 0xc098a000 - 0xc09d2880 ( 291 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_ clk_div [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 43980 46511023ns [ 0.000016] Switching to timer-based delay loop, resolution 162ns [ 0.000335] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff , max_idle_ns: 58327039986419 ns [ 0.000343] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000788] Console: colour dummy device 80x30 [ 0.000804] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000810] This ensures that you still see kernel messages. Please [ 0.000816] update your kernel commandline. [ 0.000829] Calibrating delay loop (skipped), value calculated using timer fr equency.. 12.29 BogoMIPS (lpj=61475) [ 0.000842] pid_max: default: 32768 minimum: 301 [ 0.000940] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000950] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001499] Initializing cgroup subsys io [ 0.001515] Initializing cgroup subsys memory [ 0.001540] Initializing cgroup subsys devices [ 0.001553] Initializing cgroup subsys freezer [ 0.001564] Initializing cgroup subsys perf_event [ 0.001576] Initializing cgroup subsys pids [ 0.001603] CPU: Testing write buffer coherency: ok [ 0.001801] /cpus/cpu@0 missing clock-frequency property [ 0.001817] /cpus/cpu@1 missing clock-frequency property [ 0.001827] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001861] Setting up static identity map for 0x80008380 - 0x800083e0 [ 0.080053] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.080122] Brought up 2 CPUs [ 0.080136] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.080142] CPU: All CPU(s) started in HYP mode. [ 0.080148] CPU: Virtualization extensions available. [ 0.080526] devtmpfs: initialized [ 0.109477] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.110455] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.313189] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.313211] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.318163] pinctrl core: initialized pinctrl subsystem [ 0.319031] NET: Registered protocol family 16 [ 0.319970] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.350225] cpuidle: using governor ladder [ 0.380247] cpuidle: using governor menu [ 0.388797] OMAP GPIO hardware version 0.1 [ 0.392749] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@140 0 ! [ 0.408141] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.408154] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.417234] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.417244] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.417710] omap4_sram_init:Unable to allocate sram needed to handle errata I 688 [ 0.417720] omap4_sram_init:Unable to get sram pool needed to handle errata I 688 [ 0.418294] OMAP DMA hardware revision 0.0 [ 0.461485] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver ( LinkedList1/2/3 supported) [ 0.462615] edma 43300000.edma: memcpy is disabled [ 0.467299] edma 43300000.edma: TI EDMA DMA engine driver [ 0.471363] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.471549] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.471708] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.471866] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.472139] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.472340] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.475359] palmas 0-0058: IRQ missing: skipping irq request [ 0.490815] palmas 0-0058: Muxing GPIO 2e, PWM 0, LED 0 [ 0.552686] pcf857x: probe of 0-0020 failed with error -121 [ 0.552937] pcf857x: probe of 0-0021 failed with error -121 [ 0.553794] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.554205] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.554401] media: Linux media interface: v0.10 [ 0.554453] Linux video capture interface: v2.00 [ 0.554494] pps_core: LinuxPPS API ver. 1 registered [ 0.554501] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.554530] PTP clock support registered [ 0.554580] EDAC MC: Ver: 3.0.0 [ 0.555331] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.555622] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.555947] Advanced Linux Sound Architecture Driver Initialized. [ 0.556810] clocksource: Switched to clocksource arch_sys_counter [ 0.567415] NET: Registered protocol family 2 [ 0.567918] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.567981] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.568105] TCP: Hash tables configured (established 8192 bind 8192) [ 0.568152] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.568183] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.568326] NET: Registered protocol family 1 [ 0.568638] RPC: Registered named UNIX socket transport module. [ 0.568647] RPC: Registered udp transport module. [ 0.568654] RPC: Registered tcp transport module. [ 0.568660] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.569628] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counte rs available [ 0.579624] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580268] NFS: Registering the id_resolver key type [ 0.580301] Key type id_resolver registered [ 0.580309] Key type id_legacy registered [ 0.580366] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.581642] bounce: pool size: 64 pages [ 0.581799] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 0.581815] io scheduler noop registered [ 0.581827] io scheduler deadline registered [ 0.581861] io scheduler cfq registered (default) [ 0.587339] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.590834] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges: [ 0.590848] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus 00-ff] [ 0.590880] IO 0x20003000..0x20012fff -> 0x00000000 [ 0.590901] MEM 0x20013000..0x2fffffff -> 0x20013000 [ 0.591113] dra7-pcie 51000000.pcie_rc: CFG 'Bus Master Enable' change [ 0.591123] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617606] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00 [ 0.617620] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.617630] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.617640] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 0.617701] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617718] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617742] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617757] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617780] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.617794] dra7-pcie 51000000.pcie_rc: CFG 'Memory Space Enable' change [ 0.618095] PCI: bus0: Fast back to back transfers disabled [ 0.636901] PCI: bus1: Fast back to back transfers disabled [ 0.637029] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.637044] pci 0000:00:00.0: BAR 8: assigned [mem 0x20200000-0x202fffff] [ 0.637054] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 0.637068] pci 0000:01:00.0: BAR 0: assigned [mem 0x20200000-0x20203fff 64bi t] [ 0.637116] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.637128] pci 0000:00:00.0: bridge window [mem 0x20200000-0x202fffff] [ 0.637341] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.637350] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 0.698571] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.701949] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 202, base_baud = 3000000) is a 8250 [ 1.801903] console [ttyS0] enabled [ 1.806298] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 203, base_baud = 3000000) is a 8250 [ 1.816007] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 204, base_baud = 3000000) is a 8250 [ 1.826026] [drm] Initialized drm 1.1.0 20060810 [ 1.831582] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.838270] [drm] No driver support for vblank timestamp query. [ 1.844398] [drm] Initialized vdrm 1.0.0 20110917 on minor 0 [ 1.851556] OMAP DSS rev 6.1 [ 1.855304] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_compone nt_ops) [ 1.870941] loop: module loaded [ 1.874476] vmemexp device MAJOR num = 245 [ 1.878628] vmemexp class registered [ 1.882345] /dev/vmemexp device registered [ 1.886460] ioctl DBUFIOC_EXPORT_VIRTMEM = -1072899120 [ 1.892010] nvme 0000:01:00.0: enabling device (0140 -> 0142) [ 1.898438] nand: No NAND device found [ 1.902207] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.911291] m25p80 spi32766.0: found n25q00, expected s25fl256s1 [ 1.917416] m25p80 spi32766.0: n25q00 (131072 Kbytes) [ 1.922549] 7 ofpart partitions found on MTD device spi32766.0 [ 1.928426] Creating 7 MTD partitions on "spi32766.0": [ 1.933590] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.949743] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.966056] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.983022] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.999711] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 2.007128] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 2.019595] nvme0n1: p1 [ 2.023487] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 2.041360] libphy: Fixed MDIO Bus: probed [ 2.096844] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 2.102967] libphy: 48485000.mdio: probed [ 2.120126] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driv er TI DP83867 [ 2.129075] cpsw 48484000.ethernet: Detected MACID = 78:db:2f:4d:21:9a [ 2.135730] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 2.142705] cpsw 48484000.ethernet: cpsw: Detected MACID = 78:db:2f:4d:21:9b [ 2.151340] mousedev: PS/2 mouse device common for all mice [ 2.157520] i2c /dev entries driver [ 2.166239] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.207493] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.213879] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.220643] evm_3v3_sw: supplied by sysen1 [ 2.257663] ledtrig-cpu: registered to indicate activity on CPUs [ 2.266065] aic_dvdd: supplied by evm_3v3_sw [ 2.271348] davinci-mcasp 4847c000.mcasp: invalid tdm slots: 0 [ 2.278853] NET: Registered protocol family 10 [ 2.294157] sit: IPv6 over IPv4 tunneling driver [ 2.299405] NET: Registered protocol family 17 [ 2.304088] Key type dns_resolver registered [ 2.308529] omap_voltage_late_init: Voltage driver support not added [ 2.315422] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.321645] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.328341] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.334549] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.341899] Power Management for TI OMAP4+ devices. [ 2.347058] Registering SWP/SWPB emulation handler [ 2.353203] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.360799] dmm 4e000000.dmm: initialized all PAT entries [ 2.367252] [drm] Initialized omapdrm 1.0.0 20110917 on minor 1 [ 2.395132] hctosys: unable to open rtc device (rtc0) [ 2.412088] evm_1v8: disabling [ 2.415166] aic_dvdd: disabling [ 2.418526] ldousb: disabling [ 2.421990] ALSA device list: [ 2.424971] No soundcards found. [ 2.429278] Waiting for root device PARTUUID=3cc717e1-02... [ 2.446237] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 2.457742] mmc0: new high speed SDHC card at address aaaa [ 2.463663] mmcblk0: mmc0:aaaa SL08G 7.40 GiB [ 2.469449] mmcblk0: p1 p2 [ 2.537456] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incomp atibilities [ 2.546114] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incomp atibilities [ 2.746056] EXT4-fs (mmcblk0p2): recovery complete [ 2.752209] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null) [ 2.760380] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.768847] devtmpfs: mounted [ 2.772042] Freeing unused kernel memory: 336K [ 2.776580] This architecture does not have kernel memory protection. [ 2.975113] systemd[1]: System time before build time, advancing clock. [ 3.016541] random: systemd: uninitialized urandom read (16 bytes read, 16 bi ts of entropy available) [ 3.029914] random: systemd: uninitialized urandom read (16 bytes read, 16 bi ts of entropy available) [ 3.041558] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SEL INUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL + XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 3.060077] systemd[1]: Detected architecture arm. Welcome to Arago 2016.12! [ 3.087926] systemd[1]: Set hostname to . [ 3.150392] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 17 bits of entropy available) [ 3.187103] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 18 bits of entropy available) [ 3.197412] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 18 bits of entropy available) [ 3.207710] random: systemd-gpt-aut: uninitialized urandom read (16 bytes rea d, 18 bits of entropy available) [ 3.220961] random: systemd-sysv-ge: uninitialized urandom read (16 bytes rea d, 18 bits of entropy available) [ 3.312066] random: systemd: uninitialized urandom read (16 bytes read, 21 bi ts of entropy available) [ 3.321632] random: systemd: uninitialized urandom read (16 bytes read, 21 bi ts of entropy available) [ 3.331624] random: systemd: uninitialized urandom read (16 bytes read, 21 bi ts of entropy available) [ 3.612524] systemd[1]: Configuration file /etc/systemd/system/multi-user.tar get.wants/vsdk.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.629858] systemd[1]: [/etc/systemd/system/multi-user.target.wants/vsdk.ser vice:3] Failed to add dependency on rc.pvr, ignoring: Invalid argument [ 3.731567] systemd[1]: basic.target: Found ordering cycle on basic.target/st art [ 3.739122] systemd[1]: basic.target: Found dependency on sysinit.target/star t [ 3.746387] systemd[1]: basic.target: Found dependency on alignment.service/s tart [ 3.753955] systemd[1]: basic.target: Found dependency on basic.target/start [ 3.761112] systemd[1]: basic.target: Breaking ordering cycle by deleting job alignment.service/start [ 3.770398] systemd[1]: alignment.service: Job alignment.service/start delete d to break ordering cycle starting with basic.target/start [ SKIP ] Ordering cycle found, skipping alignment.service [ 3.809350] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 3.837420] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.867171] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 3.897225] systemd[1]: Started Forward Password Requests to Wall Directory W atch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 3.927076] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 3.957085] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 3.988935] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 4.017775] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.077217] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 4.109660] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 4.149491] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 4.180203] systemd[1]: Mounting Temporary Directory... Mounting Temporary Directory... [ 4.237234] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 4.259192] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 4.268007] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 4.297130] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 4.357080] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 4.387333] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 4.417068] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 4.447237] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 4.507270] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 4.537103] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 4.557814] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 4.587056] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 4.607134] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 4.667389] systemd[1]: Starting Journal Service... Starting Journal Service... [ 4.704412] systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. [ 4.727196] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 4.757192] systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. [ 4.787339] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Setup Virtual Console. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ OK ] Started Remount Root and Kernel File Systems. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. Starting Apply Kernel Variables... Starting udev Coldplug all Devices... Starting Create Static Device Nodes in /dev... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. [ 5.521752] systemd-journald[148]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ 6.032031] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@9 5800000 [ 6.049306] remoteproc0: 55020000.ipu is available [ 6.054214] remoteproc0: Note: remoteproc is still under development and con sidered experimental. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. [ 6.086451] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.100143] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@9 9000000 [ 6.111572] remoteproc1: 40800000.dsp is available [ 6.117399] remoteproc1: Note: remoteproc is still under development and con sidered experimental. Starting Create Volatile Files and Directories... [ 6.154350] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ OK ] Started udev Coldplug all Devices. [ 6.172395] remoteproc1: Direct firmware load for dra7-dsp1-fw.xe66 failed w ith error -2 [ 6.181555] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9 f000000 [ 6.195127] remoteproc1: failed to load dra7-dsp1-fw.xe66 [ 6.209126] remoteproc2: 41000000.dsp is available [ OK ] Started Load/Save Random Seed. [ 6.220071] remoteproc2: Note: remoteproc is still under development and con sidered experimental. [ 6.256864] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backwar d compatibility isn't yet guaranteed. [ 6.291789] remoteproc2: Direct firmware load for dra7-dsp2-fw.xe66 failed w ith error -2 [ 6.314288] remoteproc2: failed to load dra7-dsp2-fw.xe66 [ OK ] Started Create Volatile Files and Directories. [ OK ] Found device /dev/ttyS0. [ 6.463846] remoteproc0: registered virtio0 (type 7) [ 6.470482] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 6.566481] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20 [ 6.587388] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0 Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Time Synchronization. [ OK ] Started Update UTMP about System Boot/Shutdown. [ 6.966317] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ 6.971765] CAN device driver interface [ 6.985365] SCSI subsystem initialized [ 7.032819] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 7.047002] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 Starting Synchronize System and HW clocks... [ OK ] Reached target System Time Synchronized. [ 7.140360] c_can_platform 4ae3c000.can: c_can_platform device registered (re gs=fce3c000, irq=254) [ OK ] Started Synchronize System and HW clocks.[ 7.409840] [drm] Initializ ed pvr 1.14.3699939 20110701 on minor 2 [ 7.452524] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 7.467035] ahci 4a140000.sata: Enable 32-bit DMA instead of 64-bit. [ 7.503636] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 im pl platform mode [ 7.554567] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pm p pio slum part ccc apst [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ 7.618262] scsi host0: ahci [ 7.621490] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x1 00 irq 240 [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on dropbear.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ 7.806799] EXT4-fs (nvme0n1p1): recovery complete [ OK ] Started D-Bus System Message Bus.[ 7.833805] EXT4-fs (nvme0n1p1): mo unted filesystem with ordered data mode. Opts: (null) [ 7.992794] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 8.007319] ata1: SATA link down (SStatus 0 SControl 300) [ OK ] Started Launching Vision SDK App. [ OK ] Started Kernel Logging Service. [ OK ] Started System Logging Service. Starting rc.pvr.service... Starting Permit User Sessions... [ 8.246038] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] Starting Network Service... Starting Login Service... [ OK ] Started Permit User Sessions. [ 8.468829] net eth0: initializing cpsw version 1.15 (0) [ OK ] Started rc.pvr.service.[ 8.485893] net eth0: initialized cpsw ale version 1.4 [ 8.516971] net eth0: ALE Table size 1024 [ 8.533837] net eth0: phy found : id is : 0x2000a231 [ 8.569734] remoteproc0: powering up 55020000.ipu [ 8.581120] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.610417] remoteproc0: Booting fw image dra7-ipu2-fw.xem4, size 4396172 [ 8.636362] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1 [ OK ] Started Network Service. [ 8.694179] remoteproc0: remote processor 55020000.ipu is now up [ 8.701492] virtio_rpmsg_bus virtio0: rpmsg host is online [ 8.745354] virtio_rpmsg_bus virtio0: creating channel rpmsg-proto addr 0x50 [ 8.782887] NET: Registered protocol family 41 [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting Network Service... Starting weston.service... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Network Service. [ OK ] Started weston.service. [ OK ] Started Login Service. Starting Network Service... Starting telnetd.service... Starting tiipclad-daemon.service... [ OK ] Started Network Service. [ OK ] Started telnetd.service. [ OK ] Started tiipclad-daemon.service. Starting Network Service... [ OK ] Started Network Service. Starting Network Service... [ OK ] Started Network Service. [FAILED] Failed to listen on Network Service Bus Name. See 'systemctl status org.freedesktop.network1.busname' for details. [FAILED] Failed to start Network Service. See 'systemctl status systemd-networkd.service' for details. [ OK ] Reached target Network. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ 13.251552] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. Opts: (null) [ 15.285182] DMA: Module install successful, device major num = 241 [ 15.291555] DRV: Module install successful _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dra7xx-evm ttyS0 Arago 2016.12 dra7xx-evm ttyS0 dra7xx-evm login: [ 15.557940] omap_l3_noc 44000000.ocp: L3 application error: target 3 mod:2 (unclearable) [ 15.566102] omap_l3_noc 44000000.ocp: L3 debug error: target 3 mod:2 (unclearable) U-Boot SPL 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... spl: falcon_args_file not set in environment, falling back to default reading single-stage-boot.dtb spl_load_image_fat_os: error reading image single-stage-boot.dtb, err - -1 reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03 +0530) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x Cascade EVM REV H.4 DRAM: 4 GiB MMC: i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 OMAP SD/MMC: 0, OMAP SD/MMC: 1 Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Card did not respond to voltage select! ERROR: invalid mmc device at arch/arm/cpu/armv7/omap-common/utils.c:193/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 ## Error: "board_findfdt" not defined i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 185 bytes read in 3 ms (59.6 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 3577032 bytes read in 176 ms (19.4 MiB/s) 107792 bytes read in 26 ms (4 MiB/s) Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x3694c8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe2000, end 8ffff50f ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.84-00041-g84382ab (x0284921@bangvideoapps02) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Mon Aug 5 14:52:40 IST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 Cascade Radar Board [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000040300000, size 3 MiB [ 0.000000] Reserved memory: initialized node cmem@40300000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 80 MiB [ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009e000000, size 32 MiB [ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a1000000, size 32 MiB [ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a3000000, size 32 MiB [ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9000000, size 64 MiB [ 0.000000] Reserved memory: initialized node cmem@A9000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] cma: Reserved 64 MiB at 0x00000000bc000000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0x000000027fd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @f2f1e000 s14912 r8192 d21952 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1025330 [ 0.000000] Kernel command line: console=ttyO0,115200n8 vram=16M root=PARTUUID=3cc717e1-02 rw rootwait ip=none cma=64M vmalloc=128M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2439424K/4109312K available (6671K kernel code, 320K rwdata, 2396K rodata, 336K init, 290K bss, 1424128K reserved, 245760K cma-reserved, 2167808K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf8000000 - 0xff800000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf7800000 ( 888 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08e302c (9069 kB) [ 0.000000] .init : 0xc08e4000 - 0xc0938000 ( 336 kB) [ 0.000000] .data : 0xc0938000 - 0xc0988220 ( 321 kB) [ 0.000000] .bss : 0xc098a000 - 0xc09d2880 ( 291 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000016] Switching to timer-based delay loop, resolution 162ns [ 0.000335] clocksource: 32k_counter: mask: 0xffffffff max_cycles U-Boot SPL 2016.05-00018-g6bc25a5 (Aug 05 2019 - 14:43:03) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v Card did not respond to voltage select! *** Warning - MMC init failed, using default environment Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... spl: falcon_args_file not set in environment, falling back to default reading single-stage-boot.dtb spl_load_image_fat_os: error reading image single-stage-boot.dtb, err - -1 reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img