
                                PLANES PROCESSOR
                                ----------------

                         03:10 PM Monday, April 22, 2013
Job Name: X:\EvmBoards\TASxxxx\TAS57xx\TAS5760\TAS5760xxEVM_RevD\PCB\TAS5760xxEVM_RevD.pcb




    POSITIVE PLANE LAYER : 1

        Plane Shapes Found On This Layer : 13
        Plane Holes  Found On This Layer : 0


        PLANE NET : GND

            Total Plane Shapes For This Net   : 1
            Use Route Border As Plane Shape   : NO
            Create Actual Plane Shapes        : NO
            Regenerate APS Connections Only   : NO
            Generate Plane Data               : YES
            Plane To Plane Clearance          : 0.175mm
            Plane To Other Metal Clearance    : 0.000mm
            Mounting Hole / Contour Clearance : 0.300mm
            Minimum Plane Gap Distance        : NA
            Use TieLeg Bridges If Needed      : YES
            Use Padstack Thermal Definition   : YES
            Default Via Tie Properties
                Tie Leg Width                 : 0.500mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Default Thru Tie Properties
                Tie Leg Width                 : 0.750mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Default SMD Tie Properties
                Tie Leg Width                 : 0.500mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Eliminate Untied Areas            : YES
            Eliminate Single Tied Areas       : NO
            Orthogonal Data Only              : NO
            Discard Areas By Dimension        : NO
            Default Hatch Width               : 0.250mm
            Default Hatch Distance            : 0.250mm
            Default Hatch Pattern             : (|) Vertical
            Default Metal Percentage          : 100.00

            Total Via  Pads Of This Net       : 264
            Total Thru Pads Of This Net       : 76
            Total SMD  Pads Of This Net       : 29

            Plane Created : Layer 1 - Net GND

                Via Pads In This Plane           : 264
                Thru Pads In This Plane          : 76
                SMD Pads In This Plane           : 29
                     
                Pads To Be Buried In Plane       : 368
                    Unconnected To Plane         : 0
                        Connected To Trace       : 0
                Pads With 4/4 Tie Connections    : 1


    POSITIVE PLANE LAYER : 2

        Plane Shapes Found On This Layer : 6
        Plane Holes  Found On This Layer : 0


        PLANE NET : GND

            Total Plane Shapes For This Net   : 1
            Use Route Border As Plane Shape   : NO
            Create Actual Plane Shapes        : NO
            Regenerate APS Connections Only   : NO
            Generate Plane Data               : YES
            Plane To Plane Clearance          : 0.250mm
            Plane To Other Metal Clearance    : 0.000mm
            Mounting Hole / Contour Clearance : 0.300mm
            Minimum Plane Gap Distance        : NA
            Use TieLeg Bridges If Needed      : YES
            Use Padstack Thermal Definition   : YES
            Default Via Tie Properties
                Tie Leg Width                 : 0.500mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Default Thru Tie Properties
                Tie Leg Width                 : 0.750mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Default SMD Tie Properties
                Tie Leg Width                 : 0.500mm
                Thermal Clearance             : 0.300mm
                Number Tie Legs               : FOUR
                Tie Orientation               : PREFER 0
            Eliminate Untied Areas            : YES
            Eliminate Single Tied Areas       : NO
            Orthogonal Data Only              : NO
            Discard Areas By Dimension        : NO
            Default Hatch Width               : 0.250mm
            Default Hatch Distance            : 0.250mm
            Default Hatch Pattern             : (|) Vertical
            Default Metal Percentage          : 100.00

            Total Via  Pads Of This Net       : 264
            Total Thru Pads Of This Net       : 76
            Total SMD  Pads Of This Net       : 26

            Plane Created : Layer 2 - Net GND

                Via Pads In This Plane           : 264
                Thru Pads In This Plane          : 76
                SMD Pads In This Plane           : 26
                     
                Pads To Be Buried In Plane       : 366
                    Unconnected To Plane         : 0
                        Connected To Trace       : 0



                        03:11 PM Monday, April 22, 2013