* Texas Instruments Data Flash File
* File created Tue Sep 05 10:45:58 2023
*
* Device Number 9E34
* Firmware Version 0.01
* Build Number 22
* Order Number 0
*
* bqz Device Number 9e34
* bqz Firmware Version 0.01
* bqz Build Number 22
*
[Voltage(Calibration)]
Cell Gain = 0
Pack Gain = 0
BAT Gain = 0
[Current(Calibration)]
CC Gain = 1.036
Capacity Gain = 1.036
[Current Offset(Calibration)]
CC Offset = 0
Coulomb Counter Offset Samples = 64
Board Offset = 0
CC Auto Config = 03
CC Auto Offset = 0
[Temperature(Calibration)]
Internal Temp Offset = 0.0
External1 Temp Offset = 0.0
External2 Temp Offset = 0.0
External3 Temp Offset = 0.0
External4 Temp Offset = 0.0
[Internal Temp Model(Calibration)]
Int Gain = -12143
Int base offset = 6232
Int Minimum AD = 0
Int Maximum Temp = 6232
[Cell Temperature Model(Calibration)]
Coeff a1 = -11130
Coeff a2 = 19142
Coeff a3 = -19262
Coeff a4 = 28203
Coeff a5 = 892
Coeff b1 = 328
Coeff b2 = -605
Coeff b3 = -2443
Coeff b4 = 4696
Rc0 = 11703
Adc0 = 11703
Rpad = 0
Rint = 0
[Fet Temperature Model(Calibration)]
Coeff a1 = -11130
Coeff a2 = 19142
Coeff a3 = -19262
Coeff a4 = 28203
Coeff a5 = 892
Coeff b1 = 328
Coeff b2 = -605
Coeff b3 = -2443
Coeff b4 = 4696
Rc0 = 11703
Adc0 = 11703
Rpad = 0
Rint = 0
[Current Deadband(Calibration)]
Deadband = 3
Coulomb Counter Deadband = 9

[Protection(Settings)]
Protection Configuration = 00
Enabled Protections A = ff
Enabled Protections B = 3f
Enabled Protections C = d5
Enabled Protections D = 0f
[Permanent Failure(Settings)]
Enabled PF A = 00
Enabled PF B = 00
Enabled PF C = 00
Enabled PF D = 00
[Configuration(Settings)]
Charging Configuration = 00
Temperature Enable = 04
Temperature Mode = 00
DA Configuration = 17
FET Options = 20
Sbs Gauging Configuration = 04
Sbs Configuration = 20
Power Config = 00
IO Config = 00
LED Configuration = 00d0
SOC Flag Config A = 0c8c
SOC Flag Config B = 8c
Balancing Configuration = 01
CEDV Gauging Configuration = 0200
CEDV Smoothing Config = 08
[AFE(Settings)]
AFE Protection Control = 70
ZVCHG Exit Threshold = 2200
[Fuse(Settings)]
PF Fuse A = 00
PF Fuse B = 00
PF Fuse C = 00
PF Fuse D = 00
Min Blow Fuse Voltage = 3500
Fuse Blow Timeout = 30
[BTP(Settings)]
Init Discharge Set = 500
Init Charge Set = 500
[SMBus(Settings)]
Address = 16
Address Check = ea
[Manufacturing(Settings)]
Mfg Status init = 0310

[CUV(Protections)]
Threshold = 2500
Delay = 2
Recovery = 3000
[COV(Protections)]
Threshold Low Temp = 4300
Threshold Standard Temp = 4300
Threshold High Temp = 4300
Threshold Rec Temp = 4300
Delay = 2
Recovery Low Temp = 3900
Recovery Standard Temp = 3900
Recovery High Temp = 3900
Recovery Rec Temp = 3900
[OCC1(Protections)]
Threshold = 6000
Delay = 6
[OCC2(Protections)]
Threshold = 8000
Delay = 3
[OCC(Protections)]
Recovery Threshold = -200
Recovery Delay = 5
[OCD1(Protections)]
Threshold = -6000
Delay = 6
[OCD2(Protections)]
Threshold = -8000
Delay = 3
[OCD(Protections)]
Recovery Threshold = 200
Recovery Delay = 5
[AOLD(Protections)]
Latch Limit = 0
Counter Dec Delay = 10
Recovery = 5
Reset = 15
Threshold = f4
[ASCC(Protections)]
Latch Limit = 0
Counter Dec Delay = 10
Recovery = 5
Reset = 15
Threshold = 77
[ASCD(Protections)]
Latch Limit = 0
Counter Dec Delay = 10
Recovery = 5
Reset = 15
Threshold 1 = 77
Threshold 2 = e7
[OTC(Protections)]
Threshold = 55.0
Delay = 2
Recovery = 50.0
[OTD(Protections)]
Threshold = 60.0
Delay = 2
Recovery = 55.0
[OTF(Protections)]
Threshold = 80.0
Delay = 2
Recovery = 65.0
[UTC(Protections)]
Threshold = 0.0
Delay = 2
Recovery = 5.0
[UTD(Protections)]
Threshold = 0.0
Delay = 2
Recovery = 5.0
[HWD(Protections)]
Delay = 10
[PTO(Protections)]
Charge Threshold = 2000
Suspend Threshold = 1800
Delay = 1800
Reset = 2
[CTO(Protections)]
Charge Threshold = 2500
Suspend Threshold = 2000
Delay = 54000
Reset = 2
[OC(Protections)]
Threshold = 300
Recovery = 2
RSOC Recovery = 90
[CHGV(Protections)]
Threshold = 500
Delay = 30
Recovery = -500
[CHGC(Protections)]
Threshold = 500
Delay = 2
Recovery Threshold = 100
Recovery Delay = 2
[PCHGC(Protections)]
Threshold = 50
Delay = 2
Recovery Threshold = 10
Recovery Delay = 2

[SUV(Permanent Fail)]
Threshold = 2200
Delay = 5
[SOV(Permanent Fail)]
Threshold = 4500
Delay = 5
[SOCC(Permanent Fail)]
Threshold = 10000
Delay = 5
[SOCD(Permanent Fail)]
Threshold = -10000
Delay = 5
[SOT(Permanent Fail)]
Threshold = 65.0
Delay = 5
[SOTF(Permanent Fail)]
Threshold = 100.0
Delay = 5
[Open Thermistor(Permanent Fail)]
Threshold = -50.0
Delay = 5
Fet Delta = 20.0
Cell Delta = 20.0
[VIMR(Permanent Fail)]
Check Voltage = 3500
Check Current = 10
Delta Threshold = 500
Delta Delay = 5
Duration = 100
[VIMA(Permanent Fail)]
Check Voltage = 3700
Check Current = 50
Delta Threshold = 200
Delay = 2
[CFET(Permanent Fail)]
OFF Threshold = 5
OFF Delay = 5
[DFET(Permanent Fail)]
OFF Threshold = -5
OFF Delay = 5
[FUSE(Permanent Fail)]
Threshold = 5
Delay = 5
[AFER(Permanent Fail)]
Threshold = 100
Delay Period = 2
Compare Period = 5
[AFEC(Permanent Fail)]
Threshold = 100
Delay Period = 5
[2LVL(Permanent Fail)]
Delay = 5
[OPNCELL(Permanent Fail)]
Threshold = 5000
Delay = 5

[Temperature Ranges(Advanced Charge Algorithm)]
T1 Temp = 0
T2 Temp = 12
T5 Temp = 20
T6 Temp = 25
T3 Temp = 30
T4 Temp = 55
Hysteresis Temp = 1
[Low Temp Charging(Advanced Charge Algorithm)]
Voltage = 4000
Current Low = 132
Current Med = 352
Current High = 264
[Standard Temp Charging(Advanced Charge Algorithm)]
Voltage = 4200
Current Low = 1980
Current Med = 4004
Current High = 2992
[High Temp Charging(Advanced Charge Algorithm)]
Voltage = 4000
Current Low = 1012
Current Med = 1980
Current High = 1496
[Rec Temp Charging(Advanced Charge Algorithm)]
Voltage = 4100
Current Low = 2508
Current Med = 4488
Current High = 3520
[Pre-Charging(Advanced Charge Algorithm)]
Current = 500
[Maintenance Charging(Advanced Charge Algorithm)]
Current = 500
[Voltage Range(Advanced Charge Algorithm)]
Precharge Start Voltage = 2500
Charging Voltage Low = 2900
Charging Voltage Med = 3600
Charging Voltage High = 4000
Charging Voltage Hysteresis = 0
[SoC Range(Advanced Charge Algorithm)]
Charging SoC Med = 50
Charging SoC High = 75
Charging SoC Hysteresis = 1
[Termination Config(Advanced Charge Algorithm)]
Charge Term Taper Current = 250
Charge Term Voltage = 75
[Charging Rate of Change(Advanced Charge Algorithm)]
Current Rate = 1
Voltage Rate = 1
[Charge Loss Compensation(Advanced Charge Algorithm)]
CCC Current Threshold = 3520
CCC Voltage Threshold = 4200
[Cell Balancing Config(Advanced Charge Algorithm)]
Cell Balance Threshold = 3900
Cell Balance Window = 100
Cell Balance Min = 40
Cell Balance Interval = 20

[Current Thresholds(Gas Gauging)]
Dsg Current Threshold = 100
Chg Current Threshold = 50
Quit Current = 10
Dsg Relax Time = 1
Chg Relax Time = 60
[Design(Gas Gauging)]
Design Capacity mAh = 4400
Design Capacity cWh = 6336
Design Voltage = 14400
[Cycle(Gas Gauging)]
Cycle Count Percentage = 90
[FD(Gas Gauging)]
Set Voltage Threshold = 3000
Clear Voltage Threshold = 3100
Set % RSOC Threshold = 0
Clear % RSOC Threshold = 5
[FC(Gas Gauging)]
Set Voltage Threshold = 4200
Clear Voltage Threshold = 4100
Set % RSOC Threshold = 100
Clear % RSOC Threshold = 95
[TD(Gas Gauging)]
Set Voltage Threshold = 3200
Clear Voltage Threshold = 3300
Set % RSOC Threshold = 6
Clear % RSOC Threshold = 8
[TC(Gas Gauging)]
Set Voltage Threshold = 4200
Clear Voltage Threshold = 4100
Set % RSOC Threshold = 100
Clear % RSOC Threshold = 95
[State(Gas Gauging)]
Cycle Count = 0
Learned Full Charge Capacity = 2600
[CEDV cfg(Gas Gauging)]
EMF = 3743
C0 = 149
R0 = 867
T0 = 4030
R1 = 316
TC = 9
C1 = 0
Age Factor = 0
Fixed EDV 0 = 3031
EDV 0 Hold Time = 1
Fixed EDV 1 = 3385
EDV 1 Hold Time = 1
Fixed EDV 2 = 3501
EDV 2 Hold Time = 1
Battery Low % = 7.00
Min Delta V Filter = 10
Learning Low Temp = 119
OverLoad Current = 5000
Self Discharge Rate = 20
Electronics Load = 0
Near Full = 200
Reserve Capacity = 0
Chg Eff = 100
Dsg Eff = 100
[CEDV Profile 1(Gas Gauging)]
Voltage 0% DOD = 4173
Voltage 10% DOD = 4043
Voltage 20% DOD = 3925
Voltage 30% DOD = 3821
Voltage 40% DOD = 3725
Voltage 50% DOD = 3656
Voltage 60% DOD = 3619
Voltage 70% DOD = 3582
Voltage 80% DOD = 3515
Voltage 90% DOD = 3439
Voltage 100% DOD = 2713
[CEDV Smoothing Config(Gas Gauging)]
Smoothing Start Voltage = 3700
Smoothing Delta Voltage = 100
Max Smoothing Current = 8000
EOC Smooth Current = 0.2
EOC Smooth Current Time = 60

[Power(Power)]
Valid Update Voltage = 3500
[Shutdown(Power)]
Shutdown Voltage = 1750
Shutdown Time = 10
PF Shutdown Voltage = 1750
PF Shutdown Time = 10
Charger Present Threshold = 3000
[Sleep(Power)]
Sleep Current = 10
Bus Timeout = 5
Voltage Time = 5
Current Time = 20
Wake Comparator = 00
[Ship(Power)]
FET Off Time = 10
Delay = 20
Auto Ship Time = 1440
[Power Off(Power)]
Timeout = 30
[Manual FET Control(Power)]
MFC Delay = 60

[Device Status Data(PF Status)]
Safety Alert A = 00
Safety Status A = 00
Safety Alert B = 00
Safety Status B = 00
Safety Alert C = 00
Safety Status C = 00
Safety Alert D = 00
Safety Status D = 00
PF Alert A = 00
PF Status A = 00
PF Alert B = 00
PF Status B = 00
PF Alert C = 00
PF Status C = 00
PF Alert D = 00
PF Status D = 00
Fuse Flag = 0000
Operation Status A = 0000
Operation Status B = 0000
Temp Range = 00
Charging Status A = 00
Charging Status B = 00
Gauging Status = 00
CEDV Status = 00
[Device Voltage Data(PF Status)]
Cell 1 Voltage = 0
Cell 2 Voltage = 0
Cell 3 Voltage = 0
Cell 4 Voltage = 0
Battery Direct Voltage = 0
Pack Voltage = 0
[Device Current Data(PF Status)]
Current = 0
[Device Temperature Data(PF Status)]
Internal Temperature = -273.2
External 1 Temperature = -273.2
External 2 Temperature = -273.2
External 3 Temperature = -273.2
External 4 Temperature = -273.2
[AFE Regs(PF Status)]
AFE Interrupt Status = 00
AFE FET Status = 00
AFE RXIN = 00
AFE Latch Status = 00
AFE Interrupt Enable = 00
AFE FET Control = 00
AFE RXIEN = 00
AFE RLOUT = 00
AFE RHOUT = 00
AFE RHINT = 00
AFE Cell Balance = 00
AFE AD/CC Control = 00
AFE ADC Mux = 00
AFE LED Output = 00
AFE State Control = 00
AFE LED/Wake Control = 00
AFE Protection Control = 00
AFE OCD = 00
AFE SCC = 00
AFE SCD1 = 00
AFE SCD2 = 00

[Manufacturer Data(System Data)]
Manufacturer Info A Length = 32
Manufacturer Info Block A01 = 61
Manufacturer Info Block A02 = 62
Manufacturer Info Block A03 = 63
Manufacturer Info Block A04 = 64
Manufacturer Info Block A05 = 65
Manufacturer Info Block A06 = 66
Manufacturer Info Block A07 = 67
Manufacturer Info Block A08 = 68
Manufacturer Info Block A09 = 69
Manufacturer Info Block A10 = 6a
Manufacturer Info Block A11 = 6b
Manufacturer Info Block A12 = 6c
Manufacturer Info Block A13 = 6d
Manufacturer Info Block A14 = 6e
Manufacturer Info Block A15 = 6f
Manufacturer Info Block A16 = 70
Manufacturer Info Block A17 = 71
Manufacturer Info Block A18 = 72
Manufacturer Info Block A19 = 73
Manufacturer Info Block A20 = 74
Manufacturer Info Block A21 = 75
Manufacturer Info Block A22 = 76
Manufacturer Info Block A23 = 77
Manufacturer Info Block A24 = 7a
Manufacturer Info Block A25 = 78
Manufacturer Info Block A26 = 79
Manufacturer Info Block A27 = 30
Manufacturer Info Block A28 = 31
Manufacturer Info Block A29 = 32
Manufacturer Info Block A30 = 33
Manufacturer Info Block A31 = 34
Manufacturer Info Block A32 = 35
[Manufacturer Info B(System Data)]
Manufacturer Info Block B01 = 01
Manufacturer Info Block B02 = 23
Manufacturer Info Block B03 = 45
Manufacturer Info Block B04 = 67
[Integrity(System Data)]
Static DF Signature = 0000
Static Chem DF Signature = 6c98
All DF Signature = 0000

[Data(SBS Configuration)]
Remaining AH Cap. Alarm = 300
Remaining WH Cap. Alarm = 432
Remaining Time Alarm = 10
Initial Battery Mode = 0081
Specification Information = 0031
Manufacture Date = 2023-9-4
Serial Number = 0001
Manufacturer Name = Texas Instruments
Device Name = bq4050
Device Chemistry = LION

[LED Config(LED Support)]
LED Flash Period = 512
LED Blink Period = 1024
LED Delay = 100
LED Hold Time = 4
CHG Flash Alarm = 10
CHG Thresh 1 = 0
CHG Thresh 2 = 20
CHG Thresh 3 = 40
CHG Thresh 4 = 60
CHG Thresh 5 = 80
DSG Flash Alarm = 10
DSG Thresh 1 = 0
DSG Thresh 2 = 20
DSG Thresh 3 = 40
DSG Thresh 4 = 60
DSG Thresh 5 = 80

[Safety Status(Black Box)]
1st Status Status A = 00
1st Status Status B = 00
1st Safety Status C = 00
1st Safety Status D = 00
1st Time to Next Event = 0
2nd Status Status A = 00
2nd Status Status B = 00
2nd Safety Status C = 00
2nd Safety Status D = 00
2nd Time to Next Event = 0
3rd Status Status A = 00
3rd Status Status B = 00
3rd Safety Status C = 00
3rd Safety Status D = 00
3rd Time to Next Event = 0
[PF Status(Black Box)]
1st PF Status A = 00
1st PF Status B = 00
1st PF Status C = 00
1st PF Status D = 00
1st Time to Next Event = 0
2nd PF Status A = 00
2nd PF Status B = 00
2nd PF Status C = 00
2nd PF Status D = 00
2nd Time to Next Event = 0
3rd PF Status A = 00
3rd PF Status B = 00
3rd PF Status C = 00
3rd PF Status D = 00
3rd Time to Next Event = 0

[Voltage(Lifetimes)]
Cell 1 Max Voltage = 4200
Cell 2 Max Voltage = 4200
Cell 3 Max Voltage = 4200
Cell 4 Max Voltage = 4200
Cell 1 Min Voltage = 3000
Cell 2 Min Voltage = 3000
Cell 3 Min Voltage = 3000
Cell 4 Min Voltage = 3000
Max Delta Cell Voltage = 3700
[Current(Lifetimes)]
Max Charge Current = 2000
Max Discharge Current = 0
Max Avg Dsg Current = 0
Max Avg Dsg Power = 0
[Temperature(Lifetimes)]
Max Temp Cell = -128
Min Temp Cell = 127
Max Delta Cell Temp = 0
Max Temp Int Sensor = -128
Min Temp Int Sensor = 127
Max Temp Fet = -128
[Safety Events(Lifetimes)]
No Of COV Events = 0
Last COV Event = 0
No Of CUV Events = 0
Last CUV Event = 0
No Of OCD1 Events = 0
Last OCD1 Event = 0
No Of OCD2 Events = 0
Last OCD2 Event = 0
No Of OCC1 Events = 0
Last OCC1 Event = 0
No Of OCC2 Events = 0
Last OCC2 Event = 0
No Of AOLD Events = 0
Last AOLD Event = 0
No Of ASCD Events = 0
Last ASCD Event = 0
No Of ASCC Events = 0
Last ASCC Event = 0
No Of OTC Events = 0
Last OTC Event = 0
No Of OTD Events = 0
Last OTD Event = 0
No Of OTF Events = 0
Last OTF Event = 0
[Charging Events(Lifetimes)]
No Valid Charge Term = 0
Last Valid Charge Term = 0
[Power Events(Lifetimes)]
No Of Shutdowns = 0
[Cell Balancing(Lifetimes)]
Cb Time Cell 1 = 0
Cb Time Cell 2 = 0
Cb Time Cell 3 = 0
Cb Time Cell 4 = 0
[Time(Lifetimes)]
Total Fw Runtime = 0
Time Spent In UT = 0
Time Spent In LT = 0
Time Spent In STL = 0
Time Spent In RT = 0
Time Spent In STH = 0
Time Spent In HT = 0
Time Spent In OT = 0