# Configure Power Supplies
###############################################
#
# Select Page 1
w 30 00 01
#
# Set the REF charging time to 40ms
w 30 7b 01
#
# Set the input power-up time to 6.4ms (for ADC)
w 30 47 32
#
# Power up ALDO
w 30 02 09
#
# Disable weak AVDD
w 30 01 08
#
# Keep ALDO Powered, enable master analog power control
w 30 02 01
#
# Set full chip common mode to 0.75V               --> 0b01xx'xxxx
# HP driver supply and HP output CM = 1.5V = LDOIN --> 0bxx11'x011
# Line output CM = full chip CM and supply = AVDD  --> 0bxxxx'0xxx
w 30 0A 73
#
### # Power-Tune ADC, PTM_R4
### w 30 3d 00
# Power-Tune ADC, PTM_R3
w 30 3d 64
# Power-Tune ADC, PTM_R1
#w 30 3d FF
#
# Power-Tune DAC, P3,P4, Class-AB
w 30 03 00 00
#
###############################################


# Clock and Interface Settings
# ---------------------------------------------
# MCLK = 24.576 MHz
###############################################
#
# Select Page 0
w 30 00 00
#
# Clock inputs: MCLK for CODEC_CLKIN
w 30 04 00
#
###############################################


# Audio Interface
###############################################
#
# Select Page 0
w 30 00 00
#
# I2S, 32 Bit, BCLK+WCLK output
# !TODO: disable output if possible
w 30 1b 3C
#
# Stereo ADC output is routed to Stereo DAC input, BCLK = DAC_CLK/1
w 30 1d 10 81
#
###############################################


# Configure ADC Channel
# PRB_R10 (Filter B): Right Channel, AOSR = 64, RC = 2, MADC = 1, ADC_CLK = 3.072 MHz, NADC = 8
# Input: In2R 10k SE
# PTM_R1 7mW (3.9mA), PTM_R3 10mW (5.6mA)
###############################################
#
# Select Page 0
w 30 00 00
#
# NADC, MADC, dividers powered on
# !TODO: use DAC divs
w 30 12 88 81
#
# PRB
w 30 3d 0A
#
# AOSR
w 30 14 40
#
#
#
# Select Page 1
w 30 00 01
#
# Route IN2R to RIGHT_P with 10K input impedance
w 30 37 10
#
# Route CM1R to RIGHT_M with 10K input impedance
w 30 39 40
#
# Unmute Right MICPGA, Gain selection of 0dB
w 30 3c 80
#
#
#
# Select Page 0
w 30 00 00
#
# Power up RADC
w 30 51 40
#
# Unmute RADC
w 30 52 80
#
###############################################


# Configure DAC Channel
# PRB_P12 (Filter B): Left Channel, DOSR = 64, RC = 3, MDAC = 2, DAC_CLK = 6.144MHz, NDAC = 4
# PRB_P16 (Filter B): Left Channel, DOSR = 64, RC = 4, MDAC = 2, DAC_CLK = 6.144MHz, NDAC = 4
# PTM_P4 HP 6.5mW (3.6mA) LO 5.7mW (3.2mA)
###############################################
#
# Select Page 0
w 30 00 00
#
# NDAC, MDAC, dividers powered on
w 30 0b 84 82
#
# PRB
w 30 3c 10
#
# DOSR
w 30 0d 00 40
#
# Power up LADC with Right as source, unmute, LDAC off
w 30 3f A0 04
#
#
#
# Select Page 1
w 30 00 01
#
# connect LDAC_P to HPL
w 30 0C 08
# HPR off
w 30 0D 00
# connect LDAC_P to LOL
w 30 0E 08
# LOR off
w 30 0F 00
#
# HPL = -2dB, unmuted (required for Power-Tune P3/4)
w 30 10 3E
# HPR = muted
w 30 11 40
# LOL = -2dB, unmuted (required for Power-Tune P3/4)
w 30 12 3E
# LOR = muted
w 30 13 40
# Power HPs/LOs Left only
w 30 09 28

#Test: mixer on
w 30 09 2B

#
###############################################


# Wait for power up
###############################################
#
# Select Page 0
w 30 00 00
#
# wait for right ADC
f 30 24 xxxxx1xx
#
# wait for left DAC, HPL, LOL
f 30 25 111xxxxx
#
###############################################