U-Boot SPL 2020.01-gf9b0d030d3 (Jun 17 2020 - 15:08:08 +0000) SYSFW ABI: 3.0 (firmware rev 0x0014 '20.04.1-v2020.04a (Terrific Lla') Trying to boot from MMC2 Loading Environment from MMC... *** Warning - No MMC card found, using default environment ** File not found /lib/firmware/j7-main-r5f0_0-fw ** ** File not found /lib/firmware/j7-mcu-r5f0_0-fw ** Starting ATF on ARM64 core... NOTICE: BL31: v2.3():07.00.00.005-dirty NOTICE: BL31: Built : 14:33:55, Jun 17 2020 U-Boot SPL 2020.01-gf9b0d030d3 (Jun 17 2020 - 14:34:25 +0000) SYSFW ABI: 3.0 (firmware rev 0x0014 '20.04.1-v2020.04a (Terrific Lla') Detected: J7X-BASE-CPB rev E3 Detected: J7X-VSC8514-ETH rev E2 Trying to boot from MMC2 U-Boot 2020.01-gf9b0d030d3 (Jun 17 2020 - 14:34:25 +0000) SoC: J721E SR1.0 Model: Texas Instruments K3 J721E SoC Board: J721EX-PM2-SOM rev E7 DRAM: 4 GiB not found for dev hbmc-mux Flash: 0 Bytes MMC: sdhci@4f80000: 0, sdhci@4fb0000: 1 Loading Environment from MMC... OK In: serial@2800000 Out: serial@2800000 Err: serial@2800000 Detected: J7X-BASE-CPB rev E3 Detected: J7X-VSC8514-ETH rev E2 Net: Warning: ethernet@046000000 using MAC address from ROM eth0: ethernet@046000000 Hit any key to stop autoboot: 0 => sf probe 0 SF: Detected mt35xu512aba with page size 256 Bytes, erase size 128 KiB, total 64 MiB => sf read 0x90000000 0x800000 0x50000 device 0 offset 0x800000, size 0x50000 SF: 327680 bytes @ 0x800000 Read: OK => sf read 0x91000000 0x900000 0x50000 device 0 offset 0x900000, size 0x50000 SF: 327680 bytes @ 0x900000 Read: OK => rproc init => rproc load 0 0x90000000 0x50000 Load Remote Processor 0 with data@addr=0x90000000 327680 bytes: Success! => rproc start 0 => rproc load 2 0x91000000 0x50000 Load Remote Processor 2 with data@addr=0x91000000 327680 bytes: Success! => rproc start 2 => boot switch to partitions #0, OK mmc1 is current device SD/MMC found on device 1 55 bytes read in 1 ms (53.7 KiB/s) Loaded env from uEnv.txt Importing environment from mmc1 ... Remote Processors are already initialized 141164 bytes read in 9 ms (15 MiB/s) Load Remote Processor 3 with data@addr=0x80080000 141164 bytes: Success! 141164 bytes read in 9 ms (15 MiB/s) Load Remote Processor 4 with data@addr=0x80080000 141164 bytes: Success! 141164 bytes read in 9 ms (15 MiB/s) Load Remote Processor 5 with data@addr=0x80080000 141164 bytes: Success! 6598528 bytes read in 16 ms (393.3 MiB/s) Load Remote Processor 8 with data@addr=0x80080000 6598528 bytes: Success! 16654344 bytes read in 347 ms (45.8 MiB/s) 89857 bytes read in 5 ms (17.1 MiB/s) 1719 bytes read in 3 ms (559.6 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Loading Device Tree to 00000000fdda1000, end 00000000fdeb9fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd080] [ 0.000000] Linux version 5.4.40-g66cf445b76 (oe-user@oe-host) (gcc version 9.2.1 20191025 (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10))) #1 SMP PREEMPT Wed Jun 17 14:28:47 UTC 2020 [ 0.000000] Machine model: Texas Instruments K3 J721E SoC [ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a0000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a0100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a1000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1100000, size 31 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a1100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a3000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a3000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a3100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a3100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a4000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a4000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a4100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a4100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a5000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a5000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a5100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a5100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a6000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node c66-dma-memory@a6000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a6100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node c66-memory@a6100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a7000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node c66-dma-memory@a7000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a7100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node c66-memory@a7100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a8000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node c71-dma-memory@a8000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a8100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node c71-memory@a8100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000ac000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node vision_apps-dma-memory@ac000000, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: initialized node vision_apps_shared-memories, compatible id dma-heap-carveout [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000ce000000, size 720 MiB [ 0.000000] OF: reserved mem: initialized node vision_apps-core-heap-memory@ce000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@fb000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@fb100000, compatible id shared-dma-pool [ 0.000000] cma: Failed to reserve 512 MiB [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 2 pages/cpu s48408 r8192 d74472 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] Built 1 zonelists, mobility grouping off. Total pages: 35779 [ 0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),-@8m(ospi.rootfs);47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),1m(hbmc.sysfw),-@8m(hbmc.rootfs) root=PARTUUID=c82fce40-02 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x9a800000-0x9e800000] (64MB) [ 0.000000] Memory: 2584064K/2293760K available (9534K kernel code, 776K rwdata, 3840K rodata, 1728K init, 695K bss, 18446744073709261312K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 960 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001900000 [ 0.000000] ITS [mem 0x01820000-0x0182ffff] [ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS [ 0.000000] ITS@0x0000000001820000: allocated 1048576 Devices @8c0800000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x00000008c00c0000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000008c00d0000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x438 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns [ 0.000001] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns [ 0.008343] Console: colour dummy device 80x25 [ 0.012911] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000) [ 0.023580] pid_max: default: 32768 minimum: 301 [ 0.028329] LSM: Security Framework initializing [ 0.033075] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) [ 0.040643] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) [ 0.072697] ASID allocator initialised with 32768 entries [ 0.086225] rcu: Hierarchical SRCU implementation. [ 0.099187] Platform MSI: gic-its@1820000 domain created [ 0.104798] PCI/MSI: /interconnect@100000/interrupt-controller@1800000/gic-its@1820000 domain created [ 0.122233] smp: Bringing up secondary CPUs ... [ 0.159206] Detected PIPT I-cache on CPU1 [ 0.159227] GICv3: CPU1: found redistributor 1 region 0:0x0000000001920000 [ 0.159239] GICv3: CPU1: using allocated LPI pending table @0x00000008c00e0000 [ 0.159270] CPU1: Booted secondary processor 0x0000000001 [0x411fd080] [ 0.159325] smp: Brought up 1 node, 2 CPUs [ 0.188669] SMP: Total of 2 processors activated. [ 0.193473] CPU features: detected: 32-bit EL0 Support [ 0.198727] CPU features: detected: CRC32 instructions [ 0.210399] CPU: All CPU(s) started at EL2 [ 0.214593] alternatives: patching kernel code [ 0.219691] devtmpfs: initialized [ 0.227895] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.237866] futex hash table entries: 512 (order: -1, 32768 bytes, linear) [ 0.245051] pinctrl core: initialized pinctrl subsystem [ 0.250810] NET: Registered protocol family 16 [ 0.255535] DMA: preallocated 256 KiB pool for atomic allocations [ 0.262016] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.277157] HugeTLB registered 16.0 GiB page size, pre-allocated 0 pages [ 0.284012] HugeTLB registered 512 MiB page size, pre-allocated 0 pages [ 0.290771] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.299541] cryptd: max_cpu_qlen set to 1000 [ 0.306800] vsys_3v3: supplied by evm_12v0 [ 0.311126] vsys_5v0: supplied by evm_12v0 [ 0.315808] iommu: Default domain type: Translated [ 0.320966] SCSI subsystem initialized [ 0.325095] mc: Linux media interface: v0.10 [ 0.329493] videodev: Linux video capture interface: v2.00 [ 0.335104] pps_core: LinuxPPS API ver. 1 registered [ 0.340173] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.349510] PTP clock support registered [ 0.353521] EDAC MC: Ver: 3.0.0 [ 0.357256] FPGA manager framework [ 0.360771] Advanced Linux Sound Architecture Driver Initialized. [ 0.367356] clocksource: Switched to clocksource arch_sys_counter [ 0.373699] VFS: Disk quotas dquot_6.6.0 [ 0.377747] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) [ 0.387302] Carveout Heap: Exported 512 MiB at 0x00000000ae000000 [ 0.393536] thermal_sys: Registered thermal governor 'step_wise' [ 0.393537] thermal_sys: Registered thermal governor 'power_allocator' [ 0.399935] NET: Registered protocol family 2 [ 0.411342] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes, linear) [ 0.420103] TCP established hash table entries: 32768 (order: 2, 262144 bytes, linear) [ 0.428300] TCP bind hash table entries: 32768 (order: 3, 524288 bytes, linear) [ 0.436078] TCP: Hash tables configured (established 32768 bind 32768) [ 0.442820] UDP hash table entries: 2048 (order: 0, 65536 bytes, linear) [ 0.449711] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes, linear) [ 0.457115] NET: Registered protocol family 1 [ 0.461864] RPC: Registered named UNIX socket transport module. [ 0.467918] RPC: Registered udp transport module. [ 0.472722] RPC: Registered tcp transport module. [ 0.477524] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.484108] PCI: CLS 0 bytes, default 64 [ 0.488472] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.499880] Initialise system trusted keyrings [ 0.504529] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.513169] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.519649] NFS: Registering the id_resolver key type [ 0.524819] Key type id_resolver registered [ 0.529090] Key type id_legacy registered [ 0.533185] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.540218] 9p: Installing v9fs 9p2000 file system support [ 0.553000] Key type asymmetric registered [ 0.557188] Asymmetric key parser 'x509' registered [ 0.562204] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.569767] io scheduler mq-deadline registered [ 0.574394] io scheduler kyber registered [ 0.579627] pinctrl-single 4301c000.pinmux: 94 pins, size 376 [ 0.585695] pinctrl-single 11c000.pinmux: 173 pins, size 692 [ 0.591884] pinctrl-single a40000.timesync_router: 512 pins, size 2048 [ 0.604876] k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 0.611159] k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 0.617493] ti-pat 31010000.pat: Found PAT Rev 1.0 with 16384 pages [ 0.623902] debugfs: Directory '31010000.pat' with parent 'regmap' already present! [ 0.631882] ti-pat 31011000.pat: Found PAT Rev 1.0 with 16384 pages [ 0.638295] debugfs: Directory '31011000.pat' with parent 'regmap' already present! [ 0.646228] ti-pat 31012000.pat: Found PAT Rev 1.0 with 16384 pages [ 0.652641] debugfs: Directory '31012000.pat' with parent 'regmap' already present! [ 0.660559] ti-pat 31013000.pat: Found PAT Rev 1.0 with 2048 pages [ 0.666879] debugfs: Directory '31013000.pat' with parent 'regmap' already present! [ 0.674789] ti-pat 31014000.pat: Found PAT Rev 1.0 with 2048 pages [ 0.681112] debugfs: Directory '31014000.pat' with parent 'regmap' already present! [ 0.690520] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.702468] brd: module loaded [ 0.708640] loop: module loaded [ 0.712197] sysfs: cannot create duplicate filename '/devices/platform/dma_buf_phys' [ 0.720124] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.40-g66cf445b76 #1 [ 0.727234] Hardware name: Texas Instruments K3 J721E SoC (DT) [ 0.733189] Call trace: [ 0.735684] dump_backtrace+0x0/0x140 [ 0.739419] show_stack+0x14/0x20 [ 0.742803] dump_stack+0xb4/0xf8 [ 0.746188] sysfs_warn_dup+0x5c/0x78 [ 0.749921] sysfs_create_dir_ns+0xd8/0xf0 [ 0.754100] kobject_add_internal+0x94/0x280 [ 0.758456] kobject_add+0x90/0xf8 [ 0.761926] device_add+0xdc/0x600 [ 0.765395] platform_device_add+0xfc/0x228 [ 0.769663] platform_device_register_full+0xc8/0x140 [ 0.774821] dma_buf_phys_init+0x68/0x94 [ 0.778822] do_one_initcall+0x50/0x190 [ 0.782736] kernel_init_freeable+0x194/0x22c [ 0.787182] kernel_init+0x10/0xfc [ 0.790651] ret_from_fork+0x10/0x18 [ 0.794311] kobject_add_internal failed for dma_buf_phys with -EEXIST, don't try to register things with the same name in the same directory. [ 0.808402] libphy: Fixed MDIO Bus: probed [ 0.812766] tun: Universal TUN/TAP device driver, 1.6 [ 0.818199] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.826202] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.832268] sky2: driver version 1.30 [ 0.836496] VFIO - User Level meta-driver version: 0.3 [ 0.842117] i2c /dev entries driver [ 0.846173] sdhci: Secure Digital Host Controller Interface driver [ 0.852490] sdhci: Copyright(c) Pierre Ossman [ 0.857139] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.863380] ledtrig-cpu: registered to indicate activity on CPUs [ 0.870129] optee: probing for conduit method from DT. [ 0.875401] optee: revision 3.8 (199fca17) [ 0.875717] optee: initialized driver [ 0.884448] NET: Registered protocol family 17 [ 0.889068] 9pnet: Installing 9P2000 support [ 0.893480] Key type dns_resolver registered [ 0.897998] registered taskstats version 1 [ 0.902186] Loading compiled-in X.509 certificates [ 0.910688] k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 0.917020] k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 0.924615] ti-sci 44083000.dmsc: ABI: 3.0 (firmware rev 0x0014 '20.04.1-v2020.04a (Terrific Lla') [ 0.950404] random: fast init done [ 0.978248] davinci-mcasp 2ba0000.mcasp: IRQ common not found [ 0.985588] omap_i2c 40b00000.i2c: bus 0 rev0.12 at 100 kHz [ 0.991586] omap_i2c 40b10000.i2c: bus 1 rev0.12 at 100 kHz [ 0.997553] omap_i2c 42120000.i2c: bus 2 rev0.12 at 100 kHz [ 1.003594] pca953x 3-0020: 3-0020 supply vcc not found, using dummy regulator [ 1.031874] pca953x 3-0022: 3-0022 supply vcc not found, using dummy regulator [ 1.039902] GPIO line 481 (MCASP/TRACE_MUX_S0) hogged as output/low [ 1.046496] GPIO line 482 (MCASP/TRACE_MUX_S1) hogged as output/high [ 1.053326] omap_i2c 2000000.i2c: bus 3 rev0.12 at 400 kHz [ 1.059216] omap_i2c 2020000.i2c: bus 4 rev0.12 at 100 kHz [ 1.065142] pca953x 5-0020: 5-0020 supply vcc not found, using dummy regulator [ 1.095722] omap_i2c 2030000.i2c: bus 5 rev0.12 at 400 kHz [ 1.101630] omap_i2c 2040000.i2c: bus 6 rev0.12 at 100 kHz [ 1.107502] omap_i2c 2050000.i2c: bus 7 rev0.12 at 100 kHz [ 1.113755] ti-sci-intr interconnect@100000:interconnect@28380000:interrupt-controller2: Interrupt Router 137 domain created [ 1.125324] ti-sci-intr interconnect@100000:interrupt-controller0: Interrupt Router 131 domain created [ 1.134942] ti-sci-intr interconnect@100000:navss@30000000:interrupt-controller1: Interrupt Router 213 domain created [ 1.145957] ti-sci-inta 33d00000.interrupt-controller: Interrupt Aggregator domain 209 created [ 2.161744] j721e-pcie 2900000.pcie: host bridge /interconnect@100000/pcie@2900000 ranges: [ 2.170218] j721e-pcie 2900000.pcie: IO 0x10001000..0x10010fff -> 0x10001000 [ 2.177695] j721e-pcie 2900000.pcie: MEM 0x10011000..0x17ffffff -> 0x10011000 [ 2.185240] j721e-pcie 2900000.pcie: PCI host bridge to bus 0000:00 [ 2.191647] pci_bus 0000:00: root bus resource [bus 00-0f] [ 2.197252] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x10001000-0x10010fff]) [ 2.206942] pci_bus 0000:00: root bus resource [mem 0x10011000-0x17ffffff] [ 2.213982] pci 0000:00:00.0: [104c:b00d] type 01 class 0x060400 [ 2.220136] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.230006] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.239891] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0xe8 may corrupt adjacent RW1C bits [ 2.249849] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.259818] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x92 may corrupt adjacent RW1C bits [ 2.269779] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0xb2 may corrupt adjacent RW1C bits [ 2.279778] pci 0000:00:00.0: supports D1 [ 2.283871] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 2.289743] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x84 may corrupt adjacent RW1C bits [ 2.299708] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x208 may corrupt adjacent RW1C bits [ 2.309759] pci 0000:00:00.0: reg 0x224: [mem 0x00000000-0x003fffff 64bit] [ 2.316785] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x00000000-0x00ffffff 64bit] (contains BAR0 for 4 VFs) [ 2.326751] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x210 may corrupt adjacent RW1C bits [ 2.336798] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x210 may corrupt adjacent RW1C bits [ 2.348357] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.357852] pci_bus 0000:01: busn_res: [bus 01-0f] end is updated to 01 [ 2.364623] pci 0000:00:00.0: BAR 7: assigned [mem 0x10400000-0x113fffff 64bit] [ 2.372101] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.377357] pcieport 0000:00:00.0: PME: Signaling with IRQ 33 [ 2.383398] pcieport 0000:00:00.0: AER: enabled with IRQ 33 [ 3.384273] j721e-pcie 2910000.pcie: host bridge /interconnect@100000/pcie@2910000 ranges: [ 3.392738] j721e-pcie 2910000.pcie: IO 0x18001000..0x18010fff -> 0x18001000 [ 3.400214] j721e-pcie 2910000.pcie: MEM 0x18011000..0x1fffffff -> 0x18011000 [ 3.407747] j721e-pcie 2910000.pcie: PCI host bridge to bus 0001:00 [ 3.414152] pci_bus 0001:00: root bus resource [bus 00-0f] [ 3.419757] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x18001000-0x18010fff]) [ 3.429625] pci_bus 0001:00: root bus resource [mem 0x18011000-0x1fffffff] [ 3.436660] pci 0001:00:00.0: [104c:b00d] type 01 class 0x060400 [ 3.442862] pci 0001:00:00.0: supports D1 [ 3.446956] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 3.454251] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.463749] pci_bus 0001:01: busn_res: [bus 01-0f] end is updated to 01 [ 3.470515] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.475744] pcieport 0001:00:00.0: PME: Signaling with IRQ 36 [ 3.481732] pcieport 0001:00:00.0: AER: enabled with IRQ 36 [ 4.484277] j721e-pcie 2920000.pcie: host bridge /interconnect@100000/pcie@2920000 ranges: [ 4.492745] j721e-pcie 2920000.pcie: IO 0x4400001000..0x4400010fff -> 0x00001000 [ 4.500576] j721e-pcie 2920000.pcie: MEM 0x4400011000..0x4407ffffff -> 0x00011000 [ 4.508463] j721e-pcie 2920000.pcie: PCI host bridge to bus 0002:00 [ 4.514869] pci_bus 0002:00: root bus resource [bus 00-0f] [ 4.520474] pci_bus 0002:00: root bus resource [io 0x20000-0x2ffff] (bus address [0x1000-0x10fff]) [ 4.529720] pci_bus 0002:00: root bus resource [mem 0x4400011000-0x4407ffffff] (bus address [0x00011000-0x07ffffff]) [ 4.540487] pci 0002:00:00.0: [104c:b00d] type 01 class 0x060400 [ 4.546689] pci 0002:00:00.0: supports D1 [ 4.550783] pci 0002:00:00.0: PME# supported from D0 D1 D3hot [ 4.558084] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.567584] pci_bus 0002:01: busn_res: [bus 01-0f] end is updated to 01 [ 4.574351] pci 0002:00:00.0: PCI bridge to [bus 01] [ 4.579613] pcieport 0002:00:00.0: PME: Signaling with IRQ 39 [ 4.585615] pcieport 0002:00:00.0: AER: enabled with IRQ 39 [ 4.592010] k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,20] sci-dev-id:235 [ 4.601885] k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: disabled [ 4.608644] k3-ringacc 2b800000.ringacc: RA Proxy rev. 66346100, num_proxies:64 [ 4.617499] k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:1024, gp-rings[440,150] sci-dev-id:211 [ 4.627649] k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: disabled [ 4.634408] k3-ringacc 3c000000.ringacc: RA Proxy rev. 66346100, num_proxies:64 [ 4.642120] omap8250 40a00000.serial: PM domain pd:149 will not be powered off [ 4.649676] 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 7, base_baud = 6000000) is a 8250 [ 4.658859] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 18, base_baud = 3000000) is a 8250 [ 4.667606] printk: console [ttyS2] enabled [ 4.667606] printk: console [ttyS2] enabled [ 4.676043] printk: bootconsole [ns16550a0] disabled [ 4.676043] printk: bootconsole [ns16550a0] disabled [ 4.686429] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 19, base_baud = 3000000) is a 8250 [ 4.695281] 2840000.serial: ttyS6 at MMIO 0x2840000 (irq = 20, base_baud = 3000000) is a 8250 [ 4.704045] arm-smmu-v3 36600000.smmu: ias 48-bit, oas 48-bit (features 0x00001faf) [ 4.712943] arm-smmu-v3 36600000.smmu: allocated 524288 entries for cmdq [ 4.721765] arm-smmu-v3 36600000.smmu: allocated 524288 entries for evtq [ 4.729325] arm-smmu-v3 36600000.smmu: msi_domain absent - falling back to wired irqs [ 4.738045] cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled [ 4.748553] cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled [ 4.758705] cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled [ 4.768943] cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled [ 4.779698] scsi host0: ufshcd [ 4.786158] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes) [ 4.792341] 7 cmdlinepart partitions found on MTD device 47040000.spi.0 [ 4.798939] Creating 7 MTD partitions on "47040000.spi.0": [ 4.804418] 0x000000000000-0x000000080000 : "ospi.tiboot3" [ 4.804422] cdns-ufshcd 4e84000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0 [ 4.822758] 0x000000080000-0x000000280000 : "ospi.tispl" [ 4.828490] 0x000000280000-0x000000680000 : "ospi.u-boot" [ 4.834279] 0x000000680000-0x0000006a0000 : "ospi.env" [ 4.839804] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup" [ 4.845991] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw" [ 4.851668] 0x000000800000-0x000004000000 : "ospi.rootfs" [ 4.867143] cdns-ufshcd 4e84000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2 [ 4.878812] cdns-ufshcd 4e84000.ufs: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0 [ 4.890090] scsi 0:0:0:49488: Well-known LUN TOSHIBA THGAF8G8T23BAILB 0300 PQ: 0 ANSI: 6 [ 4.898890] scsi 0:0:0:49476: Well-known LUN TOSHIBA THGAF8G8T23BAILB 0300 PQ: 0 ANSI: 6 [ 4.907761] cdns-ufshcd 4e84000.ufs: ufshcd_scsi_add_wlus: BOOT WLUN not found [ 5.107601] cadence-qspi 47040000.spi: Cadence QSPI NOR probe failed -517 [ 5.115329] cadence-qspi 47050000.spi: mt25qu512a (65536 Kbytes) [ 5.151588] cadence-qspi 47050000.spi: Cadence QSPI NOR probe failed -517 [ 5.195364] davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 5.203007] libphy: 46000f00.mdio: probed [ 5.208069] davinci_mdio 46000f00.mdio: phy[0]: device 46000f00.mdio:00, driver TI DP83867 [ 5.216333] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00101, cpsw version 0x6BA80100 Ports: 2 [ 5.227753] am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517 [ 5.236413] am65-cpts 310d0000.cpts: CPTS ver 0x4e8a010a, freq:200000000, add_val:4 pps:0 [ 5.244959] mmc0: CQHCI version 5.10 [ 5.283347] mmc0: SDHCI controller on 4f80000.sdhci [4f80000.sdhci] using ADMA 64-bit [ 5.292094] davinci-mcasp 2ba0000.mcasp: IRQ common not found [ 5.298663] davinci_gpio 42110000.gpio: IRQ index 4 not found [ 5.304434] davinci_gpio 42110000.gpio: IRQ not populated, err = -6 [ 5.314651] vdd_mmc1: supplied by vsys_3v3 [ 5.319446] omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc7100 [ 5.326289] omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc7100 [ 5.333113] omap-mailbox 31f82000.mailbox: omap mailbox rev 0x66fc7100 [ 5.340008] omap-mailbox 31f83000.mailbox: omap mailbox rev 0x66fc7100 [ 5.346826] omap-mailbox 31f84000.mailbox: omap mailbox rev 0x66fc7100 [ 5.356400] ti-udma 285c0000.dma-controller: Channels: 24 (tchan: 12, rchan: 12, gp-rflow: 8) [ 5.366746] ti-udma 31150000.dma-controller: Channels: 84 (tchan: 42, rchan: 42, gp-rflow: 16) [ 5.378912] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes) [ 5.385098] 7 cmdlinepart partitions found on MTD device 47040000.spi.0 [ 5.391711] Creating 7 MTD partitions on "47040000.spi.0": [ 5.397199] 0x000000000000-0x000000080000 : "ospi.tiboot3" [ 5.403299] 0x000000080000-0x000000280000 : "ospi.tispl" [ 5.409015] 0x000000280000-0x000000680000 : "ospi.u-boot" [ 5.414818] 0x000000680000-0x0000006a0000 : "ospi.env" [ 5.420363] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup" [ 5.426505] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw" [ 5.432292] 0x000000800000-0x000004000000 : "ospi.rootfs" [ 5.440166] cadence-qspi 47050000.spi: mt25qu512a (65536 Kbytes) [ 5.452636] mmc0: Command Queue Engine enabled [ 5.457082] mmc0: new HS400 MMC card at address 0001 [ 5.466398] mmcblk0: mmc0:0001 S0J56X 14.8 GiB [ 5.471044] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB [ 5.477066] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB [ 5.483060] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (240:0) [ 5.490363] davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 5.498024] libphy: 46000f00.mdio: probed [ 5.503239] davinci_mdio 46000f00.mdio: phy[0]: device 46000f00.mdio:00, driver TI DP83867 [ 5.511539] mmcblk0: p1 p2 [ 5.514397] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00101, cpsw version 0x6BA80100 Ports: 2 [ 5.527417] am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48 [ 5.534592] pps pps0: new PPS source ptp1 [ 5.538720] am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a010a, freq:500000000, add_val:1 pps:1 [ 5.547671] am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 57.4 [ 5.554967] am65-cpsw-nuss 46000000.ethernet: ALE Table size 64 [ 5.562015] mmc1: CQHCI version 5.10 [ 5.596453] mmc1: SDHCI controller on 4fb0000.sdhci [4fb0000.sdhci] using ADMA 64-bit [ 5.604621] davinci-mcasp 2ba0000.mcasp: IRQ common not found [ 5.615733] debugfs: Directory 'pd:242' with parent 'pm_genpd' already present! [ 5.623107] debugfs: Directory 'pd:241' with parent 'pm_genpd' already present! [ 5.630431] debugfs: Directory 'pd:240' with parent 'pm_genpd' already present! [ 5.637734] debugfs: Directory 'pd:239' with parent 'pm_genpd' already present! [ 5.645810] hctosys: unable to open rtc device (rtc0) [ 5.664557] ALSA device list: [ 5.667520] No soundcards found. [ 5.671179] Waiting for root device PARTUUID=c82fce40-02... [ 7.106888] mmc1: new ultra high speed DDR50 SDXC card at address aaaa [ 7.113775] mmcblk1: mmc1:aaaa SL64G 59.5 GiB [ 7.124920] mmcblk1: p1 p2 [ 7.380720] EXT4-fs (mmcblk1p2): recovery complete [ 7.386532] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 7.394643] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 7.404615] devtmpfs: mounted [ 7.407958] Freeing unused kernel memory: 1728K [ 7.412511] Run /sbin/init as init process [ 7.608061] systemd[1]: System time before build time, advancing clock. [ 7.666916] NET: Registered protocol family 10 [ 7.671821] Segment Routing with IPv6 [ 7.694473] systemd[1]: systemd 244.3+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 7.716325] systemd[1]: Detected architecture arm64. Welcome to Arago 2020.05! [ 7.758827] systemd[1]: Set hostname to . [ 7.997368] systemd[1]: /lib/systemd/system/docker.socket:6: ListenStream= references a path below legacy directory /var/run/, updating /var/run/docker.sock → /run/docker.sock; please update the unit file accordingly. [ 8.076981] random: systemd: uninitialized urandom read (16 bytes read) [ 8.083708] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 8.096033] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 8.105988] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.123449] random: systemd: uninitialized urandom read (16 bytes read) [ 8.130687] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.147420] random: systemd: uninitialized urandom read (16 bytes read) [ 8.154533] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.171529] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 8.195460] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 8.219467] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 8.235412] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 8.251407] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 8.267409] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.291372] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 8.311452] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 8.332523] systemd[1]: Listening on Process Core Dump Socket. [ OK ] Listening on Process Core Dump Socket. [ 8.351563] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 8.391398] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 8.399751] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.419643] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.435689] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 8.455602] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.471527] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.491345] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 8.514828] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 8.539541] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 8.566610] systemd[1]: Mounting Temporary Directory (/tmp)... Mounting Temporary Directory (/tmp)... [ 8.591881] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 8.619312] systemd[1]: Starting Start psplash boot splash screen... Starting Start psplash boot splash screen... [ 8.651218] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 8.675122] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 8.695577] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 8.717135] systemd[1]: Starting Journal Service... Starting Journal Service... [ 8.742319] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 8.767290] systemd[1]: Starting Remount Root and Kernel File Systems... [ 8.774299] cryptodev: loading out-of-tree module taints kernel. Starting Remount Root and Kernel File Systems... [ 8.785526] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) [ 8.797257] systemd[1]: Starting udev Coldplug all Devices... [ 8.811849] cryptodev: driver 1.10 loaded. Starting udev Coldplug all Devices... [ 8.829965] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ 8.843786] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta… nodes for the current kernel. [FAILED] Failed to start Start psplash boot splash screen. See 'systemctl status psplash-start.service' for details. [DEPEND] Dependency failed for Star…progress communication helper. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ 9.081076] systemd-journald[229]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Started udev Coldplug all Devices. [ OK ] Mounted /media/ram. [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API. [ OK ] Listening on dropbear.socket. Starting Reboot and dump vmcore via kexec... [ OK ] Listening on Docker Socket for the API. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Job spooling tools. [ OK ] Started Periodic Command Scheduler. [ OK ] Started D-Bus System Message Bus. Starting Print notice about GPLv3 packages... Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... [ OK ] Started irqbalance daemon. Starting rc.pvr.service... Starting Login Service... [ OK ] Started TEE Supplicant. [ OK ] Started Reboot and dump vmcore via kexec. [ OK ] Started IPv6 Packet Filtering Framework. [ OK ] Started IPv4 Packet Filtering Framework. [ OK ] Reached target Network (Pre). Starting Network Service... [ 10.053168] PVR_K: 305: Read BVNC 22.104.208.318 from HW device registers [ 10.064376] PVR_K: 305: RGX Device initialised with BVNC 22.104.208.318 [ OK ] Started Network Service. Starting Wait for Network to be Configured... Starting Network Name Resolution... [ 10.109214] [drm] Initialized pvr 1.10.5371573 20170530 for 4e20000000.gpu on minor 0 [ OK ] Started Login Service. [ 10.220173] rti-wdt 2200000.rti: heartbeat 60 sec [ 10.253836] k3-dsp-rproc 4d80800000.dsp: assigned reserved memory node c66-dma-memory@a7000000 [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started NFS status monitor for NFSv2/3 locking.. Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS2. [ 10.366037] k3-dsp-rproc 4d80800000.dsp: configured DSP for remoteproc mode [ OK ] Started Serial Getty on ttyS3. [ OK ] Reached target Login Prompts. Starting Synchronize System and HW clocks... [ OK ] Started Avahi mDNS/DNS-SD Stack. [FAILED] Failed to start Synchronize System and HW clocks. See 'systemctl status sync-clocks.s[ 10.406378] rti-wdt 2210000.rti: heartbeat 60 sec ervice' for details. [ 10.685115] remoteproc remoteproc0: 4d80800000.dsp is available [ 10.769351] k3-dsp-rproc 4d81800000.dsp: assigned reserved memory node c66-dma-memory@a6000000 [ 10.778119] remoteproc remoteproc0: Direct firmware load for j7-c66_0-fw failed with error -2 [ 10.786754] remoteproc remoteproc0: powering up 4d80800000.dsp [ 10.792621] remoteproc remoteproc0: Direct firmware load for j7-c66_0-fw failed with error -2 [ 10.803376] remoteproc remoteproc0: request_firmware failed: -2 [ 11.191401] k3-dsp-rproc 4d81800000.dsp: configured DSP for remoteproc mode [ 11.255401] random: crng init done [ 11.258797] random: 7 urandom warning(s) missed due to ratelimiting [ 11.335666] remoteproc remoteproc1: 4d81800000.dsp is available [ 11.366314] remoteproc remoteproc1: Direct firmware load for j7-c66_1-fw failed with error -2 [ 11.379408] remoteproc remoteproc1: powering up 4d81800000.dsp [ 11.385360] remoteproc remoteproc1: Direct firmware load for j7-c66_1-fw failed with error -2 [ OK ] Started Load/Save Random Seed. [ 11.401031] remoteproc remoteproc1: request_firmware failed: -2 [ 11.479168] k3-dsp-rproc 64800000.dsp: assigned reserved memory node c71-dma-memory@a8000000 [ 11.561868] platform 41000000.r5f: configured R5F for IPC-only mode [ 11.775819] k3-dsp-rproc 64800000.dsp: configured DSP for IPC-only mode [ 11.788989] platform 41000000.r5f: assigned reserved memory node r5f-dma-memory@a0000000 [ 11.900671] remoteproc remoteproc2: 64800000.dsp is available [ 12.040009] remoteproc remoteproc3: 41000000.r5f is available [ 12.098309] remoteproc remoteproc2: powering up 64800000.dsp [ 12.104075] remoteproc remoteproc2: Booting fw image j7-c71_0-fw, size 6598528 [ 12.117295] k3-dsp-rproc 64800000.dsp: DSP initialized in IPC-only mode [ 12.127462] remoteproc2#vdev0buffer: assigned reserved memory node c71-dma-memory@a8000000 [ 12.141187] virtio_rpmsg_bus virtio0: rpmsg host is online [ 12.143562] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xd [ 12.151402] remoteproc2#vdev0buffer: registered virtio0 (type 7) [ 12.163385] remoteproc remoteproc2: remote processor 64800000.dsp is now up *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: bash-dev bash bc binutils cifs-utils cpio dosfstools elfutils gawk gdb gdbserver glmark2 gstreamer1[ 12.288898] remoteproc remoteproc3: Direct firmware load for j7-mcu-r5f0_0-fw failed with error -2 .0-libav gzip less libasm1 libbfd libdw1 libelf1 l[ 12.302264] remoteproc remoteproc3: powering up 41000000.r5f ibgdbm-compat4 libgdbm-dev libgdbm6 libgmp10 libidn2-0 libreadline-dev libreadline8 libunistring2 m4-dev m4 [ 12.315503] remoteproc remoteproc3: Direct firmware load for j7-mcu-r5f0_0-fw failed with error -2 nettle parted tar which If you do not wish to distribut[ 12.332111] platform 5c00000.r5f: configured R5F for IPC-only mode e GPLv3 components please remove the above packages prior to di[ 12.345418] remoteproc remoteproc3: request_firmware failed: -2 [ 12.352347] TI DP83867 46000f00.mdio:00: attached PHY driver [TI DP83867] (mii_bus:phy_addr=46000f00.mdio:00, irq=POLL) stribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name pri[ 12.373290] am65-cpsw-nuss 46000000.ethernet eth0: Link is Down nted in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ 12.489431] platform 5c00000.r5f: assigned reserved memory node r5f-dma-memory@a1000000 [ 12.610746] remoteproc remoteproc4: 5c00000.r5f is available [ 12.707119] remoteproc remoteproc4: Direct firmware load for j7-main-r5f0_0-fw failed with error -2 [ 12.719391] remoteproc remoteproc4: powering up 5c00000.r5f [ 12.728084] remoteproc remoteproc4: Direct firmware load for j7-main-r5f0_0-fw failed with error -2 [ 12.730653] platform 5d00000.r5f: configured R5F for IPC-only mode [ 12.743374] remoteproc remoteproc4: request_firmware failed: -2 [ 13.014512] platform 5d00000.r5f: assigned reserved memory node r5f-dma-memory@a3000000 [ 13.115426] j721e-audio sound@0: pcm3168a-dac <-> 2ba0000.mcasp mapping ok [ 13.161617] remoteproc remoteproc5: 5d00000.r5f is available [ 13.232535] remoteproc remoteproc5: powering up 5d00000.r5f [ 13.238142] remoteproc remoteproc5: Booting fw image j7-main-r5f0_1-fw, size 141164 [ 13.247711] platform 5e00000.r5f: configured R5F for IPC-only mode [ 13.251495] platform 5d00000.r5f: R5F core initialized in IPC-only mode [ 13.260753] j721e-audio sound@0: pcm3168a-adc <-> 2ba0000.mcasp mapping ok [ 13.263378] remoteproc5#vdev0buffer: assigned reserved memory node r5f-dma-memory@a3000000 [ 13.279931] virtio_rpmsg_bus virtio1: rpmsg host is online [ 13.286574] virtio_rpmsg_bus virtio1: creating channel rpmsg_chrdev addr 0xd [ 13.291410] remoteproc5#vdev0buffer: registered virtio1 (type 7) [ 13.303439] remoteproc remoteproc5: remote processor 5d00000.r5f is now up [ 13.331152] platform 5e00000.r5f: assigned reserved memory node r5f-dma-memory@a4000000 [ 13.479524] remoteproc remoteproc6: 5e00000.r5f is available [ 13.607092] remoteproc remoteproc6: powering up 5e00000.r5f [ 13.612705] remoteproc remoteproc6: Booting fw image j7-main-r5f1_0-fw, size 141164 [ 13.621440] platform 5f00000.r5f: configured R5F for IPC-only mode [ 13.627799] platform 5e00000.r5f: R5F core initialized in IPC-only mode [ 13.634456] remoteproc6#vdev0buffer: assigned reserved memory node r5f-dma-memory@a4000000 [ 13.647964] virtio_rpmsg_bus virtio2: rpmsg host is online [ 13.654498] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0xd [ 13.659395] remoteproc6#vdev0buffer: registered virtio2 (type 7) [ 13.668697] remoteproc remoteproc6: remote processor 5e00000.r5f is now up [ 13.792066] platform 5f00000.r5f: assigned reserved memory node r5f-dma-memory@a5000000 [ 13.958501] remoteproc remoteproc7: 5f00000.r5f is available [ 14.057900] remoteproc remoteproc7: powering up 5f00000.r5f [ 14.063539] remoteproc remoteproc7: Booting fw image j7-main-r5f1_1-fw, size 141164 [ 14.075573] platform 5f00000.r5f: R5F core initialized in IPC-only mode [ 14.087409] remoteproc7#vdev0buffer: assigned reserved memory node r5f-dma-memory@a5000000 [ 14.100003] virtio_rpmsg_bus virtio3: rpmsg host is online [ 14.105551] remoteproc7#vdev0buffer: registered virtio3 (type 7) [ 14.106401] virtio_rpmsg_bus virtio3: creating channel rpmsg_chrdev addr 0xd [ 14.118177] remoteproc remoteproc7: remote processor 5f00000.r5f is now up [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-weston.slice. [ OK ] Started Weston Wayland Compositor. [ OK ] Created slice User Slice of UID 0. Starting User Runtime Directory /run/user/0... [ 14.619398] omap_rng 4e10000.trng: Random Number Generator ver. 241b34c [ OK ] Started User Runtime Directory /run/user/0. [ 14.648898] remoteproc remoteproc8: b034000.pru is available Starting User Manager for UID 0... [ 14.739889] pru-rproc b034000.pru: PRU rproc node /interconnect@100000/icssg@b000000/pru@34000 probed successfully [ 14.929308] remoteproc remoteproc9: b004000.rtu is available [ OK ] Started User Manager for UID 0. [ 14.983620] pru-rproc b004000.rtu: PRU rproc node /interconnect@100000/icssg@b000000/rtu@4000 probed successfully [ OK ] Started Session c1 of user root. [ OK ] Found device /dev/mmcblk0p1. [ OK ] Started rc.pvr.service. Starting File System Check on /dev/mmcblk0p1... Starting weston.service... [ OK ] Found device /dev/mmcblk1p1. Starting File System Check on /dev/mmcblk1p1... [ OK ] Found device /dev/mmcblk0p2. [ OK ] Started File System Check on /dev/mmcblk0p1. Mounting /run/media/mmcblk0p1... Starting File System Check on /dev/mmcblk0p2... [ OK ] Mounted /run/media/mmcblk0p1. [ 15.211337] pru-rproc b00a000.txpru: IRQ vring not found [ 15.263420] pru-rproc b00a000.txpru: IRQ kick not found [ 15.271893] remoteproc remoteproc10: b00a000.txpru is available [ 15.284635] cdns-usb3 6000000.usb: DRD version v1 (ID: 0004024e, rev: 00000200) [ 15.299117] pru-rproc b00a000.txpru: PRU rproc node /interconnect@100000/icssg@b000000/txpru@a000 probed successfully [ OK ] Started File System Check on /dev/mmcblk0p2. Mounting /run/media/mmcblk0p2... [ 15.341116] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 15.355575] remoteproc remoteproc11: b038000.pru is available [ 15.392328] cdns-usb3 6400000.usb: DRD version v1 (ID: 0004024e, rev: 00000200) [ 15.458375] pru-rproc b038000.pru: PRU rproc node /interconnect@100000/icssg@b000000/pru@38000 probed successfully [ 15.489232] remoteproc remoteproc12: b006000.rtu is available [ 15.545720] pru-rproc b006000.rtu: PRU rproc node /interconnect@100000/icssg@b000000/rtu@6000 probed successfully [ 15.603916] pru-rproc b00c000.txpru: IRQ vring not found [ 15.627348] pru-rproc b00c000.txpru: IRQ kick not found [ 15.656101] usbcore: registered new interface driver usbfs [ 15.670030] remoteproc remoteproc13: b00c000.txpru is available [ 15.680059] usbcore: registered new interface driver hub [ 15.691398] pru-rproc b00c000.txpru: PRU rproc node /interconnect@100000/icssg@b000000/txpru@c000 probed successfully [ 15.707875] usbcore: registered new device driver usb [ 15.715798] remoteproc remoteproc14: b134000.pru is available [ 15.730269] pru-rproc b134000.pru: PRU rproc node /interconnect@100000/icssg@b100000/pru@34000 probed successfully [ 15.744020] remoteproc remoteproc15: b104000.rtu is available [ 15.755413] pru-rproc b104000.rtu: PRU rproc node /interconnect@100000/icssg@b100000/rtu@4000 probed successfully [ 15.755551] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.779889] pru-rproc b10a000.txpru: IRQ vring not found [ 15.783542] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1 [ 15.788523] pru-rproc b10a000.txpru: IRQ kick not found [ 15.807477] remoteproc remoteproc16: b10a000.txpru is available [ 15.807687] xhci-hcd xhci-hcd.2.auto: hcc params 0x200073c9 hci version 0x100 quirks 0x0000000000010010 [ 15.822827] pru-rproc b10a000.txpru: PRU rproc node /interconnect@100000/icssg@b100000/txpru@a000 probed successfully [ 15.833458] xhci-hcd xhci-hcd.2.auto: irq 509, io mem 0x06410000 [ 15.843981] remoteproc remoteproc17: b138000.pru is available [ 15.847794] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 15.858007] pru-rproc b138000.pru: PRU rproc node /interconnect@100000/icssg@b100000/pru@38000 probed successfully [ 15.867359] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 15.875968] remoteproc remoteproc18: b106000.rtu is available [ 15.887568] usb usb1: Product: xHCI Host Controller [ 15.891386] pru-rproc b106000.rtu: PRU rproc node /interconnect@100000/icssg@b100000/rtu@6000 probed successfully [ 15.899359] usb usb1: Manufacturer: Linux 5.4.40-g66cf445b76 xhci-hcd [ 15.915359] usb usb1: SerialNumber: xhci-hcd.2.auto [ 15.915867] pru-rproc b10c000.txpru: IRQ vring not found [ 15.928013] hub 1-0:1.0: USB hub found [ 15.931782] pru-rproc b10c000.txpru: IRQ kick not found [ 15.937028] hub 1-0:1.0: 1 port detected [ 15.942436] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.947400] remoteproc remoteproc19: b10c000.txpru is available [ 15.953925] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 15.961620] pru-rproc b10c000.txpru: PRU rproc node /interconnect@100000/icssg@b100000/txpru@c000 probed successfully [ 15.971366] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 15.986337] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 16.141174] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04 [ 16.168223] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.193742] usb usb2: Product: xHCI Host Controller [ 16.209201] usb usb2: Manufacturer: Linux 5.4.40-g66cf445b76 xhci-hcd [ 16.224223] usb usb2: SerialNumber: xhci-hcd.2.auto [ 16.239637] hub 2-0:1.0: USB hub found [ 16.251379] hub 2-0:1.0: 1 port detected [ 16.279404] usb 1-1: new high-speed USB device number 2 using xhci-hcd _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org j7-evm ttyS2 Arago 2020.05 j7-evm ttyS2 j7-evm login: [ 16.439636] usb 1-1: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00 [ 16.451357] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=1 [ 16.458483] usb 1-1: SerialNumber: D0000859DE36 [ 16.467910] hub 1-1:1.0: USB hub found [ 16.475370] hub 1-1:1.0: 4 ports detected j7-evm login: root Last login: Wed Jun 17 14:17:26 UTC 2020 root@j7-evm:~# cd .. root@j7-evm:/home# cd .. root@j7-evm:/# cd opt root@j7-evm:/opt# ls containerd img-powervr-sdk ltp vision_apps root@j7-evm:/opt# cd vision_apps root@j7-evm:/opt/vision_apps# ls app_avp.cfg my_app_linux_arm.out test_data vx_app_srv_calibration.out app_avp2.cfg ptk_app_cfg test_data_ptk vx_app_srv_camera.out app_avp3.cfg run_app_c7x.sh uEnv.txt vx_app_srv_fileio.out app_c7x.cfg run_app_dof.sh vision_apps_init.sh vx_app_stereo_depth.out app_dof.cfg run_app_encode.sh vx_app_arm_fd_exchange_consumer.out vx_app_surround_radar_ogmap.out app_encode.cfg run_app_multi_cam.sh vx_app_arm_fd_exchange_producer.out vx_app_test_framework.out app_multi_cam.cfg run_app_pcie_video_sink.sh vx_app_arm_opengl_mosaic.out vx_app_tidl.out app_oc.cfg run_app_pcie_video_source.sh vx_app_c7x_kernel.out vx_app_tidl_1_img.txt app_oc_16bit.cfg run_app_single_cam.sh vx_app_conformance.out vx_app_tidl_2_pipe_img.txt app_od.cfg run_app_srv.sh vx_app_dense_optical_flow.out vx_app_tidl_3_data_ref_q_img.txt app_pcie_video_sink.cfg run_app_srv_avp.sh vx_app_dense_optical_flow2.out vx_app_tidl_4_pipe0_img.txt app_pcie_video_source.cfg run_app_stereo.sh vx_app_dof_sfm_fisheye.out vx_app_tidl_avp.out app_seg.cfg run_app_tidl.sh vx_app_encode.out vx_app_tidl_avp2.out app_seg_16bit.cfg run_app_tidl_16bit.sh vx_app_lidar_ogmap.out vx_app_tidl_avp3.out app_single_cam.cfg run_app_tidl_avp.sh vx_app_linux_arm_ipc.out vx_app_tidl_cam.out app_srv.cfg run_app_tidl_avp2.sh vx_app_linux_arm_mem.out vx_app_tidl_od.out app_srv_avp_cfg run_app_tidl_avp3.sh vx_app_linux_arm_remote_log.out vx_app_tidl_seg.out app_stereo.cfg run_app_tidl_cam.sh vx_app_multi_cam.out vx_app_tutorial.out app_tidl_cam.cfg run_app_tidl_od.sh vx_app_radar_gtrack.out vx_app_valet_parking.out dof_out run_app_tidl_seg.sh vx_app_sde_multilayer.out hj_app_linux_arm.out run_app_tidl_seg_16bit.sh vx_app_sde_obstacle_detection.out limits.conf run_ptk_demo.sh vx_app_single_cam.out root@j7-evm:/opt/vision_apps# ./my_app_linux_arm.out APP: Init ... !!! MEM: Init ... !!! MEM: Initialized DMA HEAP (fd=4) !!! MEM: Init ... Done !!! IPC: Init ... !!! rproc_device_find_for_name: could not open remoteproc node directory for r5f-mcu-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-mcu-core-0] rproc_device_find_for_name: could not open remoteproc node directory for r5f-main-0-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-main-0-core-0] IPC: ERROR: Unable to create TX channels for CPU [mcu1_0] !!! IPC: ERROR: Unable to create TX channels for CPU [mcu2_0] !!! IPC: Init ... Done !!! APP: ERROR: IPC init failed !!! REMOTE_SERVICE: Init ... !!! rproc_device_find_for_name: could not open remoteproc node directory for r5f-mcu-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-mcu-core-0] rproc_device_find_for_name: could not open remoteproc node directory for r5f-main-0-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-main-0-core-0] rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-0-core-1] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-1-core-0] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-1-core-1] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [c7x] @ remote endpt 21 REMOTE_SERVICE: Init ... Done !!! APP: Init ... Done !!! APP IPC: Running remote service test ... 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU c7x_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> c7x_1 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU c7x_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> c7x_1 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU mcu1_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu1_0 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU mcu1_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu1_0 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU mcu2_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu2_0 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU mcu2_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu2_0 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU mcu2_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu2_1 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU mcu2_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu2_1 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU mcu3_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu3_0 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU mcu3_0 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu3_0 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test for CPU mcu3_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu3_1 (port 21) cmd = 0x00001234, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! 0.000000 s: REMOTE_SERVICE_TEST: Running test @ 0xae000000 of 1024 bytes size for CPU mcu3_1 !!! REMOTE_SERVICE: TX: FAILED: mpu1_0 -> mcu3_1 (port 21) cmd = 0x00005678, prm_size = 4 bytes 0.000000 s: REMOTE_SERVICE_TEST: Test failed @ iteration 0 !!! APP IPC: Running remote service test ... Done. APP: Deinit ... !!! REMOTE_SERVICE: Deinit ... !!! rproc_device_find_for_name: could not open remoteproc node directory for r5f-mcu-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-mcu-core-0] rproc_device_find_for_name: could not open remoteproc node directory for r5f-main-0-core-0 IPC: ERROR: Unable to find rproc_device for rproc CPU [r5f-main-0-core-0] rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-0-core-1] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-1-core-0] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [r5f-main-1-core-1] @ remote endpt 21 rproc_device_find_chrdev_by_remote_port: could not find a matching rpmsg_chrdev node IPC: ERROR: Unable to find rproc_char_device for rproc CPU [c7x] @ remote endpt 21 REMOTE_SERVICE: Deinit ... Done !!! IPC: Deinit ... !!! Segmentation fault (core dumped) root@j7-evm:/opt/vision_apps#