U-Boot SPL 2019.01-g2bd8328-dirty (May 10 2022 - 17:36:47 +0530) DRA752-GP ES2.0 no pinctrl state for default mode Trying to boot from MMC1 no pinctrl state for default mode Loading Environment from FAT... OK U-Boot 2019.01-g2bd8328-dirty (May 10 2022 - 17:36:47 +0530) CPU : DRA752-GP ES2.0 Model: TI AM5728 BeagleBoard-X15 Board: AM572x EVM DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Loading Environment from FAT... OK Warning: fastboot.board_rev: unknown board revision invalid mmc device Net: Warning: ethernet@48484000 MAC addresses don't match: Address in ROM is e0:62:34:a2:bb:a6 Address in environment is e0:62:34:a2:b8:62 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device 4444672 bytes read in 199 ms (21.3 MiB/s) 133506 bytes read in 8 ms (15.9 MiB/s) 133560 bytes read in 8 ms (15.9 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 8ffdc000, end 8ffff981 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.79-g77dfab56c6 (root@arpita-HP-Compaq-8200-El2 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM5728 EVM [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 24 MiB at 0x00000000be400000 [ 0.000000] OMAP4: Map 0x00000000bfd00000 to (ptrval) for dram barrier [ 0.000000] On node 0 totalpages: 211968 [ 0.000000] DMA zone: 1728 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 147200 pages, LIFO batch:31 [ 0.000000] HighMem zone: 64768 pages, LIFO batch:15 [ 0.000000] DRA752 ES2.0 [ 0.000000] random: get_random_bytes called from start_kernel+0xb4/0x470 wit0 [ 0.000000] percpu: Embedded 15 pages/cpu s32396 r8192 d20852 u61440 [ 0.000000] pcpu-alloc: s32396 r8192 d20852 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 210240 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 d [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 797424K/847872K available (10240K kernel code, 332K rwda) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 333 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 270 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless [ 0.000006] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398s [ 0.000019] Switching to timer-based delay loop, resolution 162ns [ 0.000296] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xfffffffs [ 0.000307] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000819] Console: colour dummy device 80x30 [ 0.000872] Calibrating delay loop (skipped), value calculated using timer f) [ 0.000890] pid_max: default: 32768 minimum: 301 [ 0.001020] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001036] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001666] CPU: Testing write buffer coherency: ok [ 0.001709] CPU0: Spectre v2: using ICIALLU workaround [ 0.001975] /cpus/cpu@0 missing clock-frequency property [ 0.001997] /cpus/cpu@1 missing clock-frequency property [ 0.002011] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.059881] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.079881] rcu: Hierarchical SRCU implementation. [ 0.100071] EFI services will not be available. [ 0.119931] smp: Bringing up secondary CPUs ... [ 0.200270] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.200276] CPU1: Spectre v2: using ICIALLU workaround [ 0.200403] smp: Brought up 1 node, 2 CPUs [ 0.200417] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.200426] CPU: All CPU(s) started in HYP mode. [ 0.200433] CPU: Virtualization extensions available. [ 0.200939] devtmpfs: initialized [ 0.221600] VFP support v0.3: implementor 41 architecture 4 part 30 variant 0 [ 0.221877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms [ 0.221898] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.222572] pinctrl core: initialized pinctrl subsystem [ 0.223111] DMI not present or invalid. [ 0.223403] NET: Registered protocol family 16 [ 0.224619] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225613] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.420359] cpuidle: using governor ladder [ 0.420398] cpuidle: using governor menu [ 0.431103] gpio gpiochip0: (gpio-0-31): added GPIO chardev (254:0) [ 0.431177] gpiochip_setup_dev: registered GPIOs 0 to 31 on device: gpiochip) [ 0.431225] OMAP GPIO hardware version 0.1 [ 0.431858] gpio gpiochip1: (gpio-32-63): added GPIO chardev (254:1) [ 0.431933] gpiochip_setup_dev: registered GPIOs 32 to 63 on device: gpiochi) [ 0.432583] gpio gpiochip2: (gpio-64-95): added GPIO chardev (254:2) [ 0.432661] gpiochip_setup_dev: registered GPIOs 64 to 95 on device: gpiochi) [ 0.433299] gpio gpiochip3: (gpio-96-127): added GPIO chardev (254:3) [ 0.433370] gpiochip_setup_dev: registered GPIOs 96 to 127 on device: gpioch) [ 0.434007] gpio gpiochip4: (gpio-128-159): added GPIO chardev (254:4) [ 0.434079] gpiochip_setup_dev: registered GPIOs 128 to 159 on device: gpioc) [ 0.434728] gpio gpiochip5: (gpio-160-191): added GPIO chardev (254:5) [ 0.434798] gpiochip_setup_dev: registered GPIOs 160 to 191 on device: gpioc) [ 0.435442] gpio gpiochip6: (gpio-192-223): added GPIO chardev (254:6) [ 0.435518] gpiochip_setup_dev: registered GPIOs 192 to 223 on device: gpioc) [ 0.436158] gpio gpiochip7: (gpio-224-255): added GPIO chardev (254:7) [ 0.436235] gpiochip_setup_dev: registered GPIOs 224 to 255 on device: gpioc) [ 0.455314] No ATAGs? [ 0.455393] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint. [ 0.455408] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.456296] OMAP DMA hardware revision 0.0 [ 0.468223] edma 43300000.edma: memcpy is disabled [ 0.471785] edma 43300000.edma: TI EDMA DMA engine driver [ 0.479186] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver ) [ 0.479569] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed) [ 0.479861] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/' [ 0.480289] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/' [ 0.480612] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/' [ 0.480642] evm_5v0: supplied by main_12v0 [ 0.480899] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/' [ 0.481051] com_3v6: supplied by evm_5v0 [ 0.481221] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/' [ 0.481489] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed) [ 0.484166] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.484362] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.484620] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.484868] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.485242] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.485421] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.486994] SCSI subsystem initialized [ 0.488115] palmas 0-0058: Irq flag is 0x00000008 [ 0.513402] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.515020] SMPS12: supplied by regulator-dummy [ 0.516646] SMPS3: supplied by regulator-dummy [ 0.518139] SMPS45: supplied by regulator-dummy [ 0.519885] SMPS6: supplied by regulator-dummy [ 0.521503] SMPS7: supplied by regulator-dummy [ 0.523258] SMPS8: supplied by regulator-dummy [ 0.523602] smps8: Bringing 1060000uV into 1500000-1500000uV [ 0.524776] random: fast init done [ 0.525322] SMPS9: supplied by regulator-dummy [ 0.525991] LDO1: supplied by regulator-dummy [ 0.551210] LDO2: supplied by regulator-dummy [ 0.551547] ldo2: Bringing 1800000uV into 3300000-3300000uV [ 0.571083] LDO3: supplied by regulator-dummy [ 0.591094] LDO4: supplied by regulator-dummy [ 0.611114] LDO5: supplied by regulator-dummy [ 0.611800] LDO6: supplied by regulator-dummy [ 0.612466] LDO7: supplied by regulator-dummy [ 0.613138] LDO8: supplied by regulator-dummy [ 0.613824] LDO9: supplied by regulator-dummy [ 0.631152] LDOLN: supplied by regulator-dummy [ 0.651166] LDOUSB: supplied by regulator-dummy [ 0.653475] gpiochip_find_base: found new base at 504 [ 0.653648] gpio gpiochip8: (48070000.i2c:tps659038@58:tps659038_gpio): adde) [ 0.653724] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpioc) [ 0.654083] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.654723] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.655240] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 0.655437] media: Linux media interface: v0.10 [ 0.655479] videodev: Linux video capture interface: v2.00 [ 0.655553] pps_core: LinuxPPS API ver. 1 registered [ 0.655562] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom> [ 0.655584] PTP clock support registered [ 0.655615] EDAC MC: Ver: 3.0.0 [ 0.656433] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.656705] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.670742] Advanced Linux Sound Architecture Driver Initialized. [ 0.671614] clocksource: Switched to clocksource arch_sys_counter [ 0.680162] NET: Registered protocol family 2 [ 0.680951] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144) [ 0.680981] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.681044] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.681171] TCP: Hash tables configured (established 8192 bind 8192) [ 0.681267] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.681303] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.681436] NET: Registered protocol family 1 [ 0.701900] RPC: Registered named UNIX socket transport module. [ 0.701912] RPC: Registered udp transport module. [ 0.701920] RPC: Registered tcp transport module. [ 0.701928] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.701941] PCI: CLS 0 bytes, default 64 [ 0.703053] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.703251] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counte [ 0.704262] Initialise system trusted keyrings [ 0.704404] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.709548] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.720060] NFS: Registering the id_resolver key type [ 0.720084] Key type id_resolver registered [ 0.720094] Key type id_legacy registered [ 0.720138] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.721916] Key type asymmetric registered [ 0.721929] Asymmetric key parser 'x509' registered [ 0.721978] bounce: pool size: 64 pages [ 0.722015] Block layer SCSI generic (bsg) driver version 0.4 loaded (major ) [ 0.722027] io scheduler noop registered [ 0.722036] io scheduler deadline registered [ 0.722146] io scheduler cfq registered (default) [ 0.722158] io scheduler mq-deadline registered [ 0.722168] io scheduler kyber registered [ 0.728023] pinctrl-single 4a003400.pinmux: 282 pins, size 1128 [ 0.733097] pwm-backlight backlight: GPIO lookup for consumer enable [ 0.733110] pwm-backlight backlight: using device tree for GPIO lookup [ 0.733131] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of' [ 0.733149] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of ' [ 0.733162] pwm-backlight backlight: using lookup tables for GPIO lookup [ 0.733173] pwm-backlight backlight: No GPIO consumer enable found [ 0.733214] pwm-backlight backlight: backlight supply power not found, usingr [ 0.733278] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 0.736430] vdd_3v3: supplied by regen1 [ 0.736666] aic_dvdd_fixed: supplied by vdd_3v3 [ 0.736731] vtt_fixed: supplied by smps3 [ 0.785589] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.789354] console [ttyS2] disabled [ 0.789415] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 43, base_baud =0 [ 2.012978] console [ttyS2] enabled [ 2.017436] 48422000.serial: ttyS7 at MMIO 0x48422000 (irq = 44, base_baud =0 [ 2.028469] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.028680] hwrng: no data available [ 2.038477] omapdss_dss 58000000.dss: Linked as a consumer to regulator.24 [ 2.045589] omapdss_dss 58000000.dss: Dropping the link to regulator.24 [ 2.053496] tpd12s015 encoder: GPIO lookup for consumer (null) [ 2.059356] tpd12s015 encoder: using device tree for GPIO lookup [ 2.065440] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 2.074326] gpio gpiochip6: Persistence not supported for GPIO 10 [ 2.080452] tpd12s015 encoder: GPIO lookup for consumer (null) [ 2.086392] tpd12s015 encoder: using device tree for GPIO lookup [ 2.092488] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 2.101342] gpio gpiochip5: Persistence not supported for GPIO 28 [ 2.107485] tpd12s015 encoder: GPIO lookup for consumer (null) [ 2.113360] tpd12s015 encoder: using device tree for GPIO lookup [ 2.119413] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 2.128257] gpio gpiochip6: Persistence not supported for GPIO 12 [ 2.135191] connector-hdmi connector: GPIO lookup for consumer hpd [ 2.141401] connector-hdmi connector: using device tree for GPIO lookup [ 2.148074] of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of no' [ 2.156751] of_get_named_gpiod_flags: can't parse 'hpd-gpio' property of nod' [ 2.165330] connector-hdmi connector: using lookup tables for GPIO lookup [ 2.172167] connector-hdmi connector: No GPIO consumer hpd found [ 2.179248] panel-simple display: display supply power not found, using dummr [ 2.187362] panel-simple display: Linked as a consumer to regulator.0 [ 2.193853] panel-simple display: GPIO lookup for consumer enable [ 2.199975] panel-simple display: using device tree for GPIO lookup [ 2.206304] of_get_named_gpiod_flags: parsed 'enable-gpios' property of node) [ 2.215789] gpio gpiochip1: Persistence not supported for GPIO 5 [ 2.233096] brd: module loaded [ 2.243321] loop: module loaded [ 2.250715] mdio_bus fixed-0: GPIO lookup for consumer reset [ 2.256476] mdio_bus fixed-0: using lookup tables for GPIO lookup [ 2.262631] mdio_bus fixed-0: No GPIO consumer reset found [ 2.268161] libphy: Fixed MDIO Bus: probed [ 2.275728] mdio_bus 48485000.mdio: GPIO lookup for consumer reset [ 2.281971] mdio_bus 48485000.mdio: using device tree for GPIO lookup [ 2.288453] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of ' [ 2.299604] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of n' [ 2.310628] mdio_bus 48485000.mdio: using lookup tables for GPIO lookup [ 2.317287] mdio_bus 48485000.mdio: No GPIO consumer reset found [ 2.381643] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 0 [ 2.389338] libphy: 48485000.mdio: probed [ 2.405542] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of ' [ 2.418150] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driY [ 2.428419] cpsw 48484000.ethernet: No slave[1] phy_id, phy-handle, or fixedy [ 2.436766] cpsw 48484000.ethernet: Detected MACID = e0:62:34:a2:b8:62 [ 2.443384] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 2.449768] cpsw 48484000.ethernet: ALE Table size 1024 [ 2.455087] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies) [ 2.463648] i2c /dev entries driver [ 2.469128] gpio-fan gpio_fan: GPIO lookup for consumer alarm [ 2.474936] gpio-fan gpio_fan: using device tree for GPIO lookup [ 2.480980] of_get_named_gpiod_flags: can't parse 'alarm-gpios' property of ' [ 2.489744] of_get_named_gpiod_flags: can't parse 'alarm-gpio' property of n' [ 2.498487] gpio-fan gpio_fan: using lookup tables for GPIO lookup [ 2.504715] gpio-fan gpio_fan: No GPIO consumer alarm found [ 2.510321] gpio-fan gpio_fan: GPIO lookup for consumer (null) [ 2.516206] gpio-fan gpio_fan: using device tree for GPIO lookup [ 2.522277] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 2.531190] no flags found for (null) [ 2.536124] gpio-fan gpio_fan: GPIO fan initialized [ 2.544564] cpu cpu0: Linked as a consumer to regulator.8 [ 2.550065] cpu cpu0: Linked as a consumer to regulator.31 [ 2.557295] sdhci: Secure Digital Host Controller Interface driver [ 2.563578] sdhci: Copyright(c) Pierre Ossman [ 2.569103] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.575407] sdhci-omap 4809c000.mmc: GPIO lookup for consumer cd [ 2.581438] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup [ 2.588036] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/o) [ 2.597942] gpio gpiochip5: Persistence not supported for GPIO 27 [ 2.604074] omap_gpio 4805d000.gpio: Could not set line 27 debounce to 20000) [ 2.612921] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.617558] sdhci-omap 4809c000.mmc: GPIO lookup for consumer wp [ 2.623598] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup [ 2.630157] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of nod' [ 2.639355] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node' [ 2.648453] sdhci-omap 4809c000.mmc: using lookup tables for GPIO lookup [ 2.655191] sdhci-omap 4809c000.mmc: No GPIO consumer wp found [ 2.661174] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.30 [ 2.668071] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.5 [ 2.674856] sdhci-omap 4809c000.mmc: Dropping the link to regulator.5 [ 2.681534] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.15 [ 2.688423] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.5 [ 2.695307] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_3_3v mode [ 2.728839] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.736382] sdhci-omap 480ad000.mmc: GPIO lookup for consumer wp [ 2.742451] sdhci-omap 480ad000.mmc: using device tree for GPIO lookup [ 2.749040] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of nod' [ 2.758276] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node' [ 2.767399] sdhci-omap 480ad000.mmc: using lookup tables for GPIO lookup [ 2.774175] sdhci-omap 480ad000.mmc: No GPIO consumer wp found [ 2.780352] sdhci-omap 480ad000.mmc: Linked as a consumer to regulator.1 [ 2.787234] sdhci-omap 480ad000.mmc: Dropping the link to regulator.1 [ 2.793858] sdhci-omap 480ad000.mmc: Linked as a consumer to regulator.2 [ 2.800695] sdhci-omap 480ad000.mmc: Linked as a consumer to regulator.1 [ 2.807499] sdhci-omap 480ad000.mmc: no pinctrl state for sdr104 mode [ 2.814035] sdhci-omap 480ad000.mmc: no pinctrl state for ddr50 mode [ 2.820441] sdhci-omap 480ad000.mmc: no pinctrl state for hs200_1_8v mode [ 2.851675] mmc1: SDHCI controller on 480ad000.mmc [480ad000.mmc] using PIO [ 2.859308] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds) [ 2.868381] gpio gpiochip6: Persistence not supported for GPIO 9 [ 2.874507] no flags found for gpios [ 2.878474] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds) [ 2.887627] gpio gpiochip6: Persistence not supported for GPIO 8 [ 2.893842] no flags found for gpios [ 2.897766] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds) [ 2.906963] gpio gpiochip6: Persistence not supported for GPIO 14 [ 2.913336] no flags found for gpios [ 2.917104] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds) [ 2.926212] gpio gpiochip6: Persistence not supported for GPIO 15 [ 2.932429] mmc0: host does not support reading read-only switch, assuming we [ 2.932434] no flags found for gpios [ 2.944857] ledtrig-cpu: registered to indicate activity on CPUs [ 2.954479] mmc0: new high speed SDHC card at address aaaa [ 2.960670] NET: Registered protocol family 10 [ 2.966164] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ 2.971229] Segment Routing with IPv6 [ 2.974985] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.981354] NET: Registered protocol family 17 [ 2.986291] Key type dns_resolver registered [ 2.990699] Registering SWP/SWPB emulation handler [ 2.995535] omap_voltage_late_init: Voltage driver support not added [ 3.001977] Power Management for TI OMAP4+ devices. [ 3.001992] mmcblk0: p1 p2 [ 3.007482] Loading compiled-in X.509 certificates [ 3.035728] dmm 4e000000.dmm: workaround for errata i878 in use [ 3.043768] dmm 4e000000.dmm: initialized all PAT entries [ 3.050102] omapdss_dss 58000000.dss: Linked as a consumer to regulator.24 [ 3.057207] DSS: OMAP DSS rev 6.1 [ 3.062362] omapdss_hdmi5 58040000.encoder: Linked as a consumer to regulato8 [ 3.069877] omapdss_hdmi5 58040000.encoder: Dropping the link to regulator.18 [ 3.077521] tpd12s015 encoder: GPIO lookup for consumer (null) [ 3.083423] tpd12s015 encoder: using device tree for GPIO lookup [ 3.089493] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 3.098663] gpio gpiochip6: Persistence not supported for GPIO 10 [ 3.105027] tpd12s015 encoder: GPIO lookup for consumer (null) [ 3.111162] tpd12s015 encoder: using device tree for GPIO lookup [ 3.117448] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 3.126542] gpio gpiochip5: Persistence not supported for GPIO 28 [ 3.132899] tpd12s015 encoder: GPIO lookup for consumer (null) [ 3.138985] tpd12s015 encoder: using device tree for GPIO lookup [ 3.145261] of_get_named_gpiod_flags: parsed 'gpios' property of node '/enco) [ 3.154347] gpio gpiochip6: Persistence not supported for GPIO 12 [ 3.161250] omapdss_hdmi5 58040000.encoder: Linked as a consumer to regulato8 [ 3.169050] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_compon) [ 3.177035] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_comp) [ 3.212168] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.218809] [drm] No driver support for vblank timestamp query. [ 4.240616] omapdss error: HDMI I2C timeout reading EDID [ 4.251044] [drm] Enabling DMM ywrap scrolling [ 4.259156] Console: switching to colour frame buffer device 100x30 [ 4.268660] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 4.276146] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 4.283689] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 4.293275] gpio gpiochip1: Persistence not supported for GPIO 20 [ 4.299487] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 4.309041] gpio gpiochip1: Persistence not supported for GPIO 24 [ 4.315242] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 4.324782] gpio gpiochip1: Persistence not supported for GPIO 28 [ 4.330966] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 4.340519] gpio gpiochip1: Persistence not supported for GPIO 25 [ 4.346717] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio) [ 4.356253] gpio gpiochip1: Persistence not supported for GPIO 23 [ 4.362549] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 4.369667] hctosys: unable to open rtc device (rtc0) [ 4.375390] ALSA device list: [ 4.378367] No soundcards found. [ 4.385915] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 sum [ 4.426868] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. ) [ 4.435049] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 4.452654] devtmpfs: mounted [ 4.456846] Freeing unused kernel memory: 2048K [ 4.461525] Run /sbin/init as init process [ 4.824311] systemd[1]: System time before build time, advancing clock. [ 4.861114] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SE) [ 4.882639] systemd[1]: No virtualization found in DMI [ 4.887805] systemd[1]: No virtualization found in CPUID [ 4.893285] systemd[1]: Virtualization XEN not found, /proc/xen does not exit [ 4.900928] systemd[1]: No virtualization found in /proc/device-tree/* [ 4.907826] systemd[1]: UML virtualization not found in /proc/cpuinfo. [ 4.914548] systemd[1]: This platform does not support /proc/sysinfo [ 4.920932] systemd[1]: Found VM virtualization none [ 4.925955] systemd[1]: Detected architecture arm. [ 4.936842] systemd[1]: Mounting cgroup to /sys/fs/cgroup/devices of type cg. Welcome to Arago 2019.11! [ 5.041031] systemd-fstab-generator[81]: Parsing /etc/fstab [ 5.042480] systemd-gpt-auto-generator[83]: Failed to chase block device '/'y [ 5.054470] systemd-getty-generator[82]: Automatically adding serial getty f. [ 5.058159] systemd-gpt-auto-generator[83]: /dev/mmcblk0p2: root device /dev. [ 5.068977] systemd-fstab-generator[81]: Found entry what=/dev/root where=/ o [ 5.084046] systemd-fstab-generator[81]: Found entry what=proc where=/proc to [ 5.095212] systemd-fstab-generator[81]: Found entry what=devpts where=/dev/o [ 5.106378] systemd-fstab-generator[81]: Found entry what=usbdevfs where=/pro [ 5.118428] systemd-fstab-generator[81]: Found entry what=tmpfs where=/run to [ 5.132569] systemd-sysv-generator[87]: Cannot find unit umountfs.service. [ 5.139985] systemd-sysv-generator[87]: Native unit for urandom.service alre. [ 5.149231] systemd-sysv-generator[87]: Cannot find unit thermal-zone-init.s. [ 5.157459] systemd-fstab-generator[81]: Found entry what=tmpfs where=/var/vo [ 5.157776] systemd-sysv-generator[87]: Native unit for run-postinsts.servic. [ 5.178448] systemd-sysv-generator[87]: Native unit for dmesg.service alread. [ 5.186721] systemd-fstab-generator[81]: Found entry what=tmpfs where=/mediao [ 5.202216] systemd-sysv-generator[87]: Cannot find unit weston.service. [ 5.209719] systemd-sysv-generator[87]: Native unit for systemd-udevd.servic. [ 5.219422] systemd-sysv-generator[87]: Native unit for read-only-rootfs-hoo. [ 5.230159] systemd-sysv-generator[87]: Native unit for atd.service already . [ 5.239350] systemd-sysv-generator[87]: Native unit for crond.service alread. [ 5.304972] systemd-gpt-auto-generator[83]: No suitable partition table foun. [ 5.330202] systemd-sysv-ge: 131 output lines suppressed due to ratelimiting [ 5.568162] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 5.602000] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Listening on initctl Compatibility Named Pipe. [ 5.642291] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Remote File Systems. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Process Core Dump Socket. [ OK ] Reached target Swap. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice User and Session Slice. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 6.092607] random: crng init done [ 6.096050] random: 7 urandom warning(s) missed due to ratelimiting Starting File System Check on Root Device... Starting Load Kernel Modules... Mounting Temporary Directory (/tmp)... Mounting Kernel Debug File System... Starting Create list of required st��…ce nodes for the current kernel.. Mounting POSIX Message Queue File System... [ OK ] Reached target Slices. [ OK ] [ 6.199513] cmemk: loading out-of-tree module taints kernel. Listening on udev Control Socket. Starting udev Coldplug all Devices... Starting Journal Service... [ 6.214542] CMEMK module: reference Linux version 4.19.79 [ OK ] Mounted Temporary Directory (/tmp). [ 6.222920] allocated heap buffer 0x40500000 of size 0x100000 [ OK ] Mounted Kernel Debug File System. [ 6.233982] cmemk initialized [ OK ] Started Create list of required sta��…vice nodes for the current kerne. [ OK ] Mounted POSIX M[ 6.249411] systemd-journald[99]: Found cgroup2 on /r essage Queue File System. [ 6.264615] systemd-journald[99]: Journal effective settings seal=no compresB [ 6.276426] systemd-journald[99]: Fixed min_use=1.0M max_use=64.0M max_size=0 [ 6.294454] systemd-journald[99]: Reserving 14563 entries in hash table. [ 6.301970] systemd-journald[99]: Vacuuming... [ 6.306558] systemd-journald[99]: Vacuuming done, freed 0B of archived journ. [ 6.318913] systemd-journald[99]: Flushing /dev/kmsg... [ 6.327299] systemd-journald[99]: Compressed data object 538 -> 276 using XZ [ 6.362110] cryptodev: driver 1.9 loaded. [ 6.394914] omapdss error: HDMI I2C timeout reading EDID [ OK ] Started File System Check on Root Device. [ 6.411971] systemd-journald[99]: systemd-journald running as pid 99 [ 6.418905] systemd-journald[99]: Sent READY=1 notification. [ OK ] Started Journal Service. Starting Remount Root and Kernel File Systems... [ 6.472694] usbcore: registered new interface driver usbfs [ 6.479175] usbcore: registered new interface driver hub [ 6.484878] usbcore: registered new device driver usb [ 6.509634] usbcore: registered new interface driver ftdi_sio [ 6.518842] usbserial: USB Serial support registered for FTDI USB Serial Deve [ 6.528119] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Mounting /media/ram... [ OK ] Reached target Containers. [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Load/Save Random Seed. [ OK ] Found device /dev/ttyS2. [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Network Service... Starting Update UTMP about System Boot/Shutdown... [ 7.709651] ov1063x 2-0030: Probing ********************STARTED************** [ OK ] Started Update UTMP about System Boot/Shutdow[ 7.721322] ov1063x 2-! n. [ 7.731750] Driver for 1-wire Dallas network protocol. [ 7.738486] at24 0-0050: GPIO lookup for consumer wp [ 7.744410] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 7.745930] ov1063x 2-0030: GPIO 139 value: 1 [ 7.753975] at24 0-0050: using device tree for GPIO lookup [ 7.760902] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of nod' [ 7.765979] ov1063x 2-0030: GPIO 140 value: 1 [ 7.771363] omap-des 480a5000.des: will run requests pump with realtime prioy [ 7.783326] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node' [ 7.793582] at24 0-0050: using lookup tables for GPIO lookup [ 7.804588] at24 0-0050: No GPIO consumer wp found [ 7.822270] ov1063x 2-0030: GPIO 113 value: 1 [ 7.834866] ov1063x 2-0030: setting gpio done! [ 7.839429] ov1063x 2-0030: xvclk_rate: 6000000 (Hz) [ 7.851194] ov1063x_get_default_format: ov1063x mf->width: 384 [ 7.857523] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.:. Driver in Intere [ 7.865760] ov1063x_get_default_format: ov1063x mf->height: 288 [ 7.871798] ov1063x_get_default_format: ov1063x mf->colorspace: 1 [ 7.872106] pixcir_ts 4-005c: GPIO lookup for consumer attb [ 7.877929] ov1063x_get_default_format: ov1063x mf->code: 8198 [ 7.889521] ov1063x_get_default_format: ov1063x mf->field: 1 [ 7.895512] ov1063x 2-0030: priv->width: 384 [ 7.899865] ov1063x 2-0030: priv->height: 288 [ 7.904819] pixcir_ts 4-005c: using device tree for GPIO lookup [ 7.918667] ov1063x 2-0030: ov1063x Product ID 0 Manufacturer ID 1 [ 7.934579] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: GPIO lookup d [ 7.936125] of_get_named_gpiod_flags: can't parse 'attb-gpios' property of n' [ 7.950920] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: using devicep [ 7.954211] ov1063x 2-0030: ov1063x 2-0030 sensor driver registered !! [ 7.971374] rtc rtc1: 48070000.i2c:tps659038@58:tps659038_rtc: dev (253:1) [ 7.971862] ov1063x 2-0030: Probing ********************SUCCESS************** [ 7.993506] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: rtc core: re1 [ 7.993701] of_get_named_gpiod_flags: parsed 'attb-gpio' property of node '/) [ 8.007784] of_get_named_gpiod_flags: can't parse 'id-gpios' property of nod' [ 8.056927] gpio gpiochip1: Persistence not supported for GPIO 4 [ 8.064733] pixcir_ts 4-005c: GPIO lookup for consumer reset [ 8.072147] of_get_named_gpiod_flags: can't parse 'id-gpio' property of node' [ 8.090543] pixcir_ts 4-005c: using device tree for GPIO lookup [ 8.100718] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: using lookupp [ 8.105606] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of ' [ 8.120578] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: No GPIO consd [ 8.129724] w1_master_driver w1_bus_master1: Attaching one wire slave 01.000d [ 8.138671] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: GPIO lookup s [ OK ] Started Network Time Synchronization. [ 8.204494] w1_master_driver w1_bus_master1: Family 1 for 01.000000000000.3d. [ 8.208100] palmas-usb 48070000.i2c:tps659038@58:tps659038_usb: using devicep [ OK ] Reached target System Time Synchronized. [ 8.232520] of_get_named_gpiod_flags: parsed 'reset-gpio' property of node ') [ 8.246282] of_get_named_gpiod_flags: can't parse 'vbus-gpios' property of n' [ 8.279110] omap_rtc 48838000.rtc: char device (253:2) [ 8.284912] of_get_named_gpiod_flags: parsed 'vbus-gpio' property of node '/) [ 8.286191] omap_rtc 48838000.rtc: registered as rtc2 [ OK ] Reached target System Initialization. [ 8.318442] gpio gpiochip1: Persistence not supported for GPIO 6 [ 8.321084] gpio gpiochip3: Persistence not supported for GPIO 21 [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activati[ 8.334367] pixcir_ts e on Socket. [ 8.366975] pixcir_ts 4-005c: using device tree for GPIO lookup Starting Reboot and dump vmcore via kexec... [ OK ] Listening on RPCbind Server Activation Socket[ 8.406124] vpe 489d00n . [ 8.417655] of_get_named_gpiod_flags: can't parse 'wake-gpios' property of n' [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ 8.462102] vpe 489d0000.vpe: Device registered as /dev/video0 [ 8.468564] of_get_named_gpiod_flags: can't parse 'wake-gpio' property of no' [ OK ] Started Daily rotation of log files. [ 8.506022] pixcir_ts 4-005c: using lookup tables for GPIO lookup [ OK ] Reached target Timers. [ 8.520316] vip 489b0000.vip: loading firmware vpdma-1b8.bin [ 8.527584] pixcir_ts 4-005c: No GPIO consumer wake found [ 8.551985] vip 489b0000.vip: VPDMA firmware loaded [ 8.557729] pixcir_ts 4-005c: GPIO lookup for consumer enable [ 8.557779] vin6a: Port A: Using subdev ov1063x 2-0030 for capture [ OK ] Listening on dropbear.socket. [ 8.583497] pixcir_ts 4-005c: using device tree for GPIO lookup [ 8.589461] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of' [ 8.600336] vin6a-0: device registered as video1 [ 8.605264] net eth0: initializing cpsw version 1.15 (0) [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting RPC Bind Service... [ 8.672377] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of ' [ 8.734029] Micrel KSZ9021 Gigabit PHY 48485000.mdio:01: attached PHY driver) [ 8.748913] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 8.760128] pixcir_ts 4-005c: using lookup tables for GPIO lookup [ 8.789909] pixcir_ts 4-005c: No GPIO consumer enable found [ 8.796646] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 8.796849] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ 8.813414] libphy: PHY not found Starting Login Service... [ 8.841678] net eth0: phy "" not found on slave 1, err -19 [ OK ] Started Job spooling tools. [ 8.860747] omap-aes 4b500000.aes: will run requests pump with realtime prioy [ 8.871025] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Starting TI IPC Daemon... [ 8.903467] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 8.923906] omap-aes 4b700000.aes: will run requests pump with realy Starting rc.pvr.service... Starting Print notice about GPLv3 packages... [ 8.975383] omap-hdmi-audio omap-hdmi-audio.0.auto: snd-soc-dummy-dai <-> 58k [ OK ] Started Periodic Command Scheduler. [ 9.008199] [drm] Initialized pvr 1.17.4948957 20110701 for 56000000.gpu on 1 [ 9.034862] omap-hdmi-audio omap-hdmi-audio.0.auto: ASoC: no DMI vendor name! [ OK ] Started D-Bus System Message Bus. Starting TI MultiCore Tools Daemon... [ OK ] Started Network Service. [ 9.167472] PVR_K: UM DDK-(4948957) and KM DDK-(4948957) match. [ OK ] [ OK ] Started Reboot and dump vmcore via kexec. [ OK ] Started RPC Bind Service. [ OK ] Started TI IPC Daemon. [ OK ] Started rc.pvr.service. [ OK ] Started TI MultiCore Tools Daemon. [ 10.081769] omap_i2c 4807c000.i2c: controller timed out [ 10.111703] pixcir_ts 4-005c: pixcir_set_power_mode: can't read reg 0x33 : -0 [ 10.132123] pixcir_ts 4-005c: Failed to set IDLE mode [ 10.171843] pixcir_ts: probe of 4-005c failed with error -110 [ 10.604231] systemd[1]: Sent message type=signal sender=n/a destination=n/a a [ 10.833018] systemd[1]: sys-devices-virtual-block-ram0.device: Changed dead d [ 10.873335] systemd[1]: dev-ram12.device: Changed dead -> plugged [ 10.888200] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow cof [ 10.897517] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 11.253347] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.289470] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.300993] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.311343] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.311651] systemd[1]: dev-ram3.device: Changed dead -> plugged [ 11.322148] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.337823] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.342280] systemd[1]: sys-devices-virtual-block-ram3.device: Changed dead d [ 11.348385] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.366242] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.371636] systemd[1]: Sent message type=signal sender=n/a destination=n/a a [ 11.376742] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.407620] systemd-journald[99]: Journal effective settings seal=no compresB [ 11.411646] systemd[1]: Sent message type=signal sender=n/a destination=n/a a [ 11.490140] dwc3 48890000.usb: Failed to get clk 'ref': -2 [ 11.503798] OF: graph: no port node found in /ocp/ocp2scp@4a080000/phy@4a0840 [ 11.542376] dwc3 488d0000.usb: Failed to get clk 'ref': -2 [ 11.548204] dwc3 48890000.usb: changing max_speed on rev 5533202a [ 11.554999] OF: graph: no port node found in /ocp/ocp2scp@4a080000/phy@4a0850 [ 12.965257] cpsw 48484000.ethernet eth0: Link is Down *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf bash-dev bash bc binutils-dev binutils bison-dev bison cifs-utils cpio cpp-symlinks cpp dosfstools elfutils-dev elfutils findutils g++-symlinks g++ gawk gcc-symlinks gcc gdb gdbc6x gdbserver gettext glmark2 gstreamer1.0-libav gzip hidapi libasm1 libbfd libcairo-perf-utils libdw1 libelf1 libgdbm-compat4 libgdbm-dev libgdbm6 libgettextlib libgettextsrc libgmp10 libidn2-0 libmavconn libmpc3 libmpfr6 libreadline-dev libreadline7 libunistring2 m4-dev m4 make mavlink mavros-extras mavros-msgs mavros nettle parted pdm-anomaly-detection socketcan-interface swig-dev swig which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ 14.006313] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow cof Starting Save/Restore Sound Card State... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Created slice system-systemd\x2dfsck.slice. Starting File System Check on /dev/mmcblk0p1... [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen Backlight��…ightness of backlight:backlight.. Starting weston.service... Starting Network Name Resolution... Starting Wait for Network to be Configured... [ OK ] Started Save/Restore Sound Card State. [ OK ] Reached target Sound Card. [ OK ] Started Login Service. [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight. [ OK ] Started weston.service. Starting telnetd.service... Starting Matrix GUI... [ OK ] Started telnetd.service. Starting thttpd.service... [ OK ] Started File System Check on /dev/mmcblk0p1. Mounting /run/media/mmcblk0p1... [ OK ] Started Matrix GUI. [ OK ] Started thttpd.service. [ OK ] Started Network Name Resolution. [ OK ] Mounted /run/media/mmcblk0p1. [ OK ] Reached target Network. Starting Permit User Sessions... [ OK ] Started Redis In-Memory Data Store. Starting Lightning Fast Webserver With Light System Requirements... Starting Enable and configure wl18xx bluetooth stack... Starting Simple Network Management Protocol (SNMP) Daemon.... Starting Avahi mDNS/DNS-SD Stack... [ 15.428278] gpio gpiochip4: Persistence not supported for GPIO 4 [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started Permit User Sessions. [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Serial Getty on ttyS2. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. Starting Synchronize System and HW clocks... [FAILED] Failed to start Synchronize System and HW clocks. See 'systemctl status sync-clocks.service' for details. [ 16.085144] cpsw 48484000.ethernet eth0: Link is Down [ 16.443329] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.453999] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.468768] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.479000] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.525898] systemd-journald[99]: Journal effective settings seal=no compresB [ OK ] Started Enable and configure wl18xx bluetooth[ 16.537017] systemd-joB stack. [ 16.554232] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.570735] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.581290] systemd-journald[99]: Journal effective settings seal=no compresB [ 16.592482] systemd-journald[99]: Journal effective settings seal=no compresB [ 17.126180] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow cof [ 17.341674] omapdss error: HDMI I2C timeout reading EDID [ OK ] Started Simple Network Management Protocol (SNMP) Daemon.. [ 19.205153] cpsw 48484000.ethernet eth0: Link is Down [ 20.246251] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow cof _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS2 Arago 2019.11 am57xx-evm ttyS2 am57xx-evm login: [ 22.335212] cpsw 48484000.ethernet eth0: Link is Down [ 22.341305] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.361716] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.372571] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.382813] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.393647] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.403867] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.414274] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.424494] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.435199] systemd-journald[99]: Journal effective settings seal=no compresB [ 22.445424] systemd-journald[99]: Journal effective settings seal=no compresB [ 23.366151] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow cof [ 25.445200] cpsw 48484000.ethernet eth0: Link is Down [ 26.486301] cpsw 48484000.ethernet eth0: Link is Up - 10Mbps/Full - flow conf [ 27.606975] systemd-journald[99]: Journal effective settings seal=no compresB [ 27.617196] systemd-journald[99]: Journal effective settings seal=no compresB [ 27.627604] systemd-journald[99]: Journal effective settings seal=no compresB [ 27.637928] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.462824] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.473051] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.886905] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.897118] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.907510] systemd-journald[99]: Journal effective settings seal=no compresB [ 29.917698] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.255989] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.266213] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.276848] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.287085] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.401664] aic_dvdd_fixed: disabling [ 34.411692] systemd-journald[99]: Journal effective settings seal=no compresB [ 34.421901] systemd-journald[99]: Journal effective settings seal=no compresB [ 36.019578] systemd-journald[99]: Journal effective settings seal=no compresB [ 36.029805] systemd-journald[99]: Journal effective settings seal=no compresB [ 36.128257] systemd-journald[99]: Journal effective settings seal=no compresB [ 36.138476] systemd-journald[99]: Journal effective settings seal=no compresB _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS2 Arago 2019.11 am57xx-evm ttyS2 am57xx-evm login: _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS2 Arago 2019.11 am57xx-evm ttyS2 am57xx-evm login: _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS2 Arago 2019.11 am57xx-evm ttyS2 am57xx-evm login: root