                                        ti,nand-ecc-opt = "bch8";       /* from baseboard file */
                                        ti,elm-id = <&elm>;
                                        nand-bus-width = <8>;
                                        gpmc,device-width = <1>;
                                        gpmc,sync-clk-ps = <0>;
                                        gpmc,cs-on-ns = <0>;            /* from baseboard file */
                                        gpmc,cs-rd-off-ns = <44>;       /* from baseboard file */
                                        gpmc,cs-wr-off-ns = <44>;       /* from baseboard file */
                                        gpmc,adv-on-ns = <6>;           /* from baseboard file */
                                        gpmc,adv-rd-off-ns = <34>;      /* from baseboard file */
                                        gpmc,adv-wr-off-ns = <44>;      /* from baseboard file */
                                        gpmc,we-on-ns = <0>;
                                        gpmc,we-off-ns = <40>;          /* from baseboard file */
                                        gpmc,oe-on-ns = <0>;
                                        gpmc,oe-off-ns = <54>;          /* from baseboard file */
                                        gpmc,access-ns = <64>;          /* from baseboard file */
                                        gpmc,rd-cycle-ns = <82>;        /* from baseboard file */
                                        gpmc,wr-cycle-ns = <82>;        /* from baseboard file */
                                        gpmc,wait-on-read = "true";
                                        gpmc,wait-on-write = "true";
                                        gpmc,bus-turnaround-ns = <0>;
                                        gpmc,cycle2cycle-delay-ns = <0>;
                                        gpmc,clk-activation-ns = <0>;
                                        gpmc,wait-monitoring-ns = <0>;
                                        gpmc,wr-access-ns = <40>;       /* from baseboard file */
                                        gpmc,wr-data-mux-bus-ns = <0>;














U-Boot 2018.01-g2659de8-dirty (Oct 16 2019 - 03:06:12 +0530)

CPU  : AM335X-GP rev 1.0
I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB



Srini debug @ line 427 in function initr_mmc in file common/board_r.c


MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1



Srini debug @ line 430 in function initr_mmc in file common/board_r.c





Srini debug @ line 462 in function initr_env in file common/board_r.c


Entering env_relocate



Srini debug @ line 221 in function env_relocate in file env/common.c


Received string is <NULL>
SriniManju Using default environment

Exiting set_default_env
Exiting env_relocate
In:    ns16550_serial
Out:   ns16550_serial
Err:   ns16550_serial
Net:   Could not find PHY for cpsw: phy_mask 6
cpsw
Hit any key to stop autoboot:  0 
=> 
=> 
=> 
=> fatload mmc 0:1 0x88000000 am335x-mitysom-devkit_1.dtb
reading am335x-mitysom-devkit_1.dtb
45706 bytes read in 20 ms (2.2 MiB/s)
=> setenv bootargs console=ttyS0,115200n8 root=/dev/mmcblk0p2
=> fatload mmc 0:1 0x82000000 zImage
reading zImage
3871232 bytes read in 310 ms (11.9 MiB/s)
=> bootz 0x82000000 - 0x88000000
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Using Device Tree in place at 88000000, end 8800e289
ret = 0

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (pcadmin@pcadmin-OptiPlex-790) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)9
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Critical Link MitySOM-335x Devkit
[    0.000000] Memory policy: Data cache writeback
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 48 MiB at 0x8d000000
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] AM335X ES1.0 (sgx neon)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 197264K/262144K available (8192K kernel code, 319K rwdata, 2492K rodata, 1024K init, 267K bss, 15728K reserve)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0d4fd40   ( 320 kB)
[    0.000000]        .bss : 0xc0d4fd40 - 0xc0d92a94   ( 268 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[    0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000043] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000055] OMAP clocksource: timer1 at 24000000 Hz
[    0.000269] timer_probe: no matching timers found
[    0.000509] Console: colour dummy device 80x30
[    0.000564] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)
[    0.118902] pid_max: default: 32768 minimum: 301
[    0.119121] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.119139] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.120049] CPU: Testing write buffer coherency: ok
[    0.120125] CPU0: Spectre v2: using BPIALL workaround
[    0.120924] Setting up static identity map for 0x80100000 - 0x80100060
[    0.121103] Hierarchical SRCU implementation.
[    0.121509] EFI services will not be available.
[    0.123124] devtmpfs: initialized
[    0.133701] random: get_random_u32 called from bucket_table_alloc+0x8c/0x1ac with crng_init=0
[    0.134204] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    0.134554] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.134580] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.138718] pinctrl core: initialized pinctrl subsystem
[    0.139763] DMI not present or invalid.
[    0.140239] NET: Registered protocol family 16
[    0.142777] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.159779] omap_hwmod: debugss: _wait_target_disable failed
[    0.188761] cpuidle: using governor ladder
[    0.188804] cpuidle: using governor menu
[    0.188921] 
[    0.188921] 
[    0.188921] 
[    0.188921] Srini debug @ line 2997 in function gpmc_init in file drivers/memory/omap-gpmc.c
[    0.188921] 
[    0.188921] 
[    0.188967] GPMC_REVISION           = 60
[    0.188976] GPMC_SYSCONFIG          = 11
[    0.188983] GPMC_SYSSTATUS          = 1
[    0.188990] GPMC_IRQSTATUS          = 0
[    0.188997] GPMC_IRQENABLE          = 0
[    0.189004] GPMC_TIMEOUT_CONTROL    = 1ff0
[    0.189010] GPMC_ERR_ADDRESS        = 0
[    0.189017] GPMC_ERR_TYPE           = 0
[    0.189024] GPMC_CONFIG             = 12
[    0.189031] GPMC_STATUS             = 101
[    0.189037] GPMC_CONFIG1_0          = 800
[    0.189045] GPMC_CONFIG2_0          = 1e1e00
[    0.189051] GPMC_CONFIG3_0          = 1e1e00
[    0.189058] GPMC_CONFIG4_0          = 16051807
[    0.189065] GPMC_CONFIG5_0          = 151e1e
[    0.189073] GPMC_CONFIG6_0          = 16000f80
[    0.189079] GPMC_CONFIG7_0          = f48
[    0.189089] 
[    0.189089] 
[    0.189089] Srini debug @ line 423 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    0.189089] 
[    0.189103] print_hardware_sfrs
[    0.189103] 
[    0.189113] Value of AD0 at location 0x44e10800 is 0x30
[    0.189122] Value of AD1 at location 0x44e10804 is 0x30
[    0.189130] Value of AD2 at location 0x44e10808 is 0x30
[    0.189138] Value of AD3 at location 0x44e1080c is 0x30
[    0.189146] Value of AD4 at location 0x44e10810 is 0x30
[    0.189154] Value of AD5 at location 0x44e10814 is 0x30
[    0.189162] Value of AD6 at location 0x44e10818 is 0x30
[    0.189170] Value of AD7 at location 0x44e1081c is 0x30
[    0.189178] Value of AD8 at location 0x44e10820 is 0x27
[    0.189186] Value of AD9 at location 0x44e10824 is 0x27
[    0.189194] Value of AD10 at location 0x44e10828 is 0x27
[    0.189202] Value of AD11 at location 0x44e1082c is 0x27
[    0.189210] Value of AD12 at location 0x44e10830 is 0x27
[    0.189218] Value of AD13 at location 0x44e10834 is 0x27
[    0.189226] Value of AD14 at location 0x44e10838 is 0x27
[    0.189234] Value of AD15 at location 0x44e1083c is 0x27
[    0.189240] 
[    0.189248] Value of A16 at location 0x44e108a4 is 0x2f
[    0.189257] Value of A17 at location 0x44e108a8 is 0x2f
[    0.189265] Value of A18 at location 0x44e108ac is 0x2f
[    0.189272] Value of A19 at location 0x44e108b0 is 0x2f
[    0.189280] Value of A20 at location 0x44e108b4 is 0x2f
[    0.189289] Value of A21 at location 0x44e108b8 is 0x2f
[    0.189297] Value of A22 at location 0x44e108bc is 0x2f
[    0.189302] 
[    0.189310] Value of A23 at location 0x44e108e0 is 0x27
[    0.189318] Value of A24 at location 0x44e108e4 is 0x27
[    0.189326] Value of A25 at location 0x44e108e8 is 0x27
[    0.189332] 
[    0.189339] Value of A26 at location 0x44e1086c is 0x22
[    0.189339] 
[    0.189349] Value of CS0             at location 0x44e1087c is 0x0
[    0.189349] 
[    0.189359] Value of ALE             at location 0x44e10890 is 0x0
[    0.189359] 
[    0.189369] Value of OEN_REN         at location 0x44e10894 is 0x0
[    0.189369] 
[    0.189379] Value of BEN0_CLE        at location 0x44e1089c is 0x0
[    0.189379] 
[    0.189389] Value of WEN             at location 0x44e10898 is 0x0
[    0.189389] 
[    0.189399] Value of WAIT0           at location 0x44e10870 is 0x30
[    0.189399] 
[    0.189410] 
[    0.189410] 
[    0.189410] Srini debug @ line 487 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    0.189410] 
[    0.189423] End of print_hardware_sfrs...
[    0.189423] 
[    0.194435] OMAP GPIO hardware version 0.1
[    0.206093] omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_de
[    0.209439] No ATAGs?
[    0.209459] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.225031] edma 49000000.edma: TI EDMA DMA engine driver
[    0.229478] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, e
[    0.229558] omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c1_pins, e
[    0.229605] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, e
[    0.229786] media: Linux media interface: v0.10
[    0.229837] Linux video capture interface: v2.00
[    0.229971] pps_core: LinuxPPS API ver. 1 registered
[    0.229981] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.230009] PTP clock support registered
[    0.230050] EDAC MC: Ver: 3.0.0
[    0.230582] dmi: Firmware registration failed.
[    0.231242] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[    0.231687] Advanced Linux Sound Architecture Driver Initialized.
[    0.232990] clocksource: Switched to clocksource timer1
[    0.242543] NET: Registered protocol family 2
[    0.243483] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.243525] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.243556] TCP: Hash tables configured (established 2048 bind 2048)
[    0.243676] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.243699] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.243887] NET: Registered protocol family 1
[    0.244409] RPC: Registered named UNIX socket transport module.
[    0.244425] RPC: Registered udp transport module.
[    0.244433] RPC: Registered tcp transport module.
[    0.244441] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.245432] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.245571] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
[    0.247341] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.252227] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.253424] NFS: Registering the id_resolver key type
[    0.253478] Key type id_resolver registered
[    0.253487] Key type id_legacy registered
[    0.253541] ntfs: driver 2.1.32 [Flags: R/O].
[    0.255984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.256010] io scheduler noop registered
[    0.256020] io scheduler deadline registered
[    0.256281] io scheduler cfq registered (default)
[    0.256294] io scheduler mq-deadline registered
[    0.256304] io scheduler kyber registered
[    0.257525] pinctrl-single 44e10800.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.257946] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.261609] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.318776] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.322432] console [ttyS0] disabled
[    0.322544] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250
[    1.297738] console [ttyS0] enabled
[    1.302514] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 31, base_baud = 3000000) is a 8250
[    1.312497] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 32, base_baud = 3000000) is a 8250
[    1.323681] omap_rng 48310000.rng: Random Number Generator ver. 20
[    1.332595] pinctrl-single 44e10800.pinmux: pin PIN40 already requested by lcd-controller@1; cannot claim for 4830e000.lcdc
[    1.343939] pinctrl-single 44e10800.pinmux: pin-40 (4830e000.lcdc) status -22
[    1.351116] pinctrl-single 44e10800.pinmux: could not request pin 40 (PIN40) from group lcd_pins_default  on device pinctrl-single
[    1.362932] tilcdc 4830e000.lcdc: Error applying setting, reverse things back
[    1.370143] tilcdc: probe of 4830e000.lcdc failed with error -22
[    1.389402] brd: module loaded
[    1.400355] loop: module loaded
[    1.408124] m25p80 spi1.0: m25p64 (8192 Kbytes)
[    1.412721] 1 ofpart partitions found on MTD device spi1.0
[    1.418434] Creating 1 MTD partitions on "spi1.0":
[    1.423291] 0x000000000000-0x000000800000 : "NOR User Defined"
[    1.431393] libphy: Fixed MDIO Bus: probed
[    1.503088] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000
[    1.510794] davinci_mdio 4a101000.mdio: no live phy, scanning all
[    1.517444] davinci_mdio: probe of 4a101000.mdio failed with error -5
[    1.524927] cpsw 4a100000.ethernet: Detected MACID = d0:ff:50:45:d9:c6
[    1.531599] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
[    1.538054] cpsw 4a100000.ethernet: ALE Table size 1024
[    1.543366] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies)
[    1.552418] i2c /dev entries driver
[    1.556679] IR NEC protocol handler initialized
[    1.561237] IR RC5(x/sz) protocol handler initialized
[    1.566359] IR RC6 protocol handler initialized
[    1.570909] IR JVC protocol handler initialized
[    1.575471] IR Sony protocol handler initialized
[    1.580106] IR SANYO protocol handler initialized
[    1.584842] IR Sharp protocol handler initialized
[    1.589565] IR MCE Keyboard/mouse protocol handler initialized
[    1.595434] IR XMP protocol handler initialized
[    1.601450] cpu cpu0: "syscon" is missing, cannot use OPPv2 table.
[    1.607809] cpuidle: enable-method property 'ti,am3352' found operations
[    1.615017] sdhci: Secure Digital Host Controller Interface driver
[    1.621229] sdhci: Copyright(c) Pierre Ossman
[    1.683379] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.693253] ledtrig-cpu: registered to indicate activity on CPUs
[    1.708104] NET: Registered protocol family 10
[    1.714198] Segment Routing with IPv6
[    1.717972] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.724853] NET: Registered protocol family 17
[    1.729670] Key type dns_resolver registered
[    1.734266] omap_voltage_late_init: Voltage driver support not added
[    1.747682] 
[    1.747682] 
[    1.747682] 
[    1.747682] Srini debug @ line 2837 in function gpmc_probe in file drivers/memory/omap-gpmc.c
[    1.747682] 
[    1.747682] 
[    1.764015] Value of res->start is 57
[    1.767742] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.775983] mmc0: new high speed SDHC card at address 59b4
[    1.782099] Value of res->end is 57
[    1.785722] mmcblk0: mmc0:59b4 USDU1 14.7 GiB 
[    1.791233]  mmcblk0: p1 p2
[    1.795263] 
[    1.795263] 
[    1.795263] 
[    1.795263] Srini debug @ line 2696 in function gpmc_probe_dt in file drivers/memory/omap-gpmc.c
[    1.795263] 
[    1.795263] 
[    1.811585] Value returned for gpmc,num-cs is 0 and gpmc,num-cs: 7
[    1.817837] gpmc,num-cs Success....
[    1.821355] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    1.826537] 
[    1.826537] 
[    1.826537] 
[    1.826537] Srini debug @ line 1723 in function gpmc_mem_init in file drivers/memory/omap-gpmc.c
[    1.826537] 
[    1.826537] 
[    1.842799] Value of GPMC_CS_CONFIG7 is 3912
[    1.847099] CS0 is enabled, so validating...
[    1.851386] 
[    1.851386] 
[    1.851386] 
[    1.851386] Srini debug @ line 1149 in function gpmc_cs_get_memconf in file drivers/memory/omap-gpmc.c
[    1.851386] 
[    1.851386] 
[    1.868195] GPMC_REVISION           = 60
[    1.872133] GPMC_SYSCONFIG          = 11
[    1.876086] GPMC_SYSSTATUS          = 1
[    1.879935] GPMC_IRQSTATUS          = 0
[    1.883807] GPMC_IRQENABLE          = 0
[    1.887657] GPMC_TIMEOUT_CONTROL    = 1ff0
[    1.891767] GPMC_ERR_ADDRESS        = 0
[    1.895631] GPMC_ERR_TYPE           = 0
[    1.899481] GPMC_CONFIG             = 12
[    1.903431] GPMC_STATUS             = 101
[    1.907454] GPMC_CONFIG1_0          = 800
[    1.911477] GPMC_CONFIG2_0          = 1e1e00
[    1.915776] GPMC_CONFIG3_0          = 1e1e00
[    1.920062] GPMC_CONFIG4_0          = 16051807
[    1.924535] GPMC_CONFIG5_0          = 151e1e
[    1.928821] GPMC_CONFIG6_0          = 16000f80
[    1.933294] GPMC_CONFIG7_0          = f48
[    1.937320] 
[    1.937320] 
[    1.937320] Srini debug @ line 423 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    1.937320] 
[    1.951044] print_hardware_sfrs
[    1.951044] 
[    1.955696] Value of AD0 at location 0x44e10800 is 0x30
[    1.960942] Value of AD1 at location 0x44e10804 is 0x30
[    1.966201] Value of AD2 at location 0x44e10808 is 0x30
[    1.971447] Value of AD3 at location 0x44e1080c is 0x30
[    1.976706] Value of AD4 at location 0x44e10810 is 0x30
[    1.981952] Value of AD5 at location 0x44e10814 is 0x30
[    1.987210] Value of AD6 at location 0x44e10818 is 0x30
[    1.992456] Value of AD7 at location 0x44e1081c is 0x30
[    1.997714] Value of AD8 at location 0x44e10820 is 0x27
[    2.002960] Value of AD9 at location 0x44e10824 is 0x27
[    2.008223] Value of AD10 at location 0x44e10828 is 0x27
[    2.013569] Value of AD11 at location 0x44e1082c is 0x27
[    2.018903] Value of AD12 at location 0x44e10830 is 0x27
[    2.024250] Value of AD13 at location 0x44e10834 is 0x27
[    2.029583] Value of AD14 at location 0x44e10838 is 0x27
[    2.034929] Value of AD15 at location 0x44e1083c is 0x27
[    2.040259] 
[    2.041754] Value of A16 at location 0x44e108a4 is 0x8
[    2.046926] Value of A17 at location 0x44e108a8 is 0x8
[    2.052084] Value of A18 at location 0x44e108ac is 0x8
[    2.057257] Value of A19 at location 0x44e108b0 is 0x8
[    2.062415] Value of A20 at location 0x44e108b4 is 0x8
[    2.067588] Value of A21 at location 0x44e108b8 is 0x8
[    2.072745] Value of A22 at location 0x44e108bc is 0x8
[    2.077915] 
[    2.079412] Value of A23 at location 0x44e108e0 is 0x0
[    2.084583] Value of A24 at location 0x44e108e4 is 0x0
[    2.089741] Value of A25 at location 0x44e108e8 is 0x0
[    2.094910] 
[    2.096405] Value of A26 at location 0x44e1086c is 0x22
[    2.096405] 
[    2.103149] Value of CS0             at location 0x44e1087c is 0x8
[    2.103149] 
[    2.109878] Value of ALE             at location 0x44e10890 is 0x8
[    2.109878] 
[    2.116710] Value of OEN_REN         at location 0x44e10894 is 0x8
[    2.116710] 
[    2.123802] Value of BEN0_CLE        at location 0x44e1089c is 0x8
[    2.123802] 
[    2.130882] Value of WEN             at location 0x44e10898 is 0x8
[    2.130882] 
[    2.137713] Value of WAIT0           at location 0x44e10870 is 0x30
[    2.137713] 
[    2.144807] 
[    2.144807] 
[    2.144807] Srini debug @ line 487 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    2.144807] 
[    2.158530] End of print_hardware_sfrs...
[    2.158530] 
[    2.164053] GPMC_CS_CONFIG7 value read : 0xf48
[    2.168513] Srini -> Value of cs is 0
[    2.172188] Srini -> Value of base is 134217728
[    2.176748] Srini -> Value of size is 16777216
[    2.176748] 
[    2.176748] 
[    2.184192] 
[    2.184192] 
[    2.184192] 
[    2.184192] Srini debug @ line 1219 in function gpmc_cs_insert_mem in file drivers/memory/omap-gpmc.c
[    2.184192] 
[    2.184192] 
[    2.200887] 
[    2.200887] 
[    2.200887] 
[    2.200887] Srini debug @ line 1202 in function gpmc_mem_align in file drivers/memory/omap-gpmc.c
[    2.200887] 
[    2.200887] 
[    2.217235] Srini -> gpmc_cs_insert_mem SUCCESS !!!!!!
[    2.217235] 
[    2.217235] 
[    2.225375] Value of GPMC_CS_CONFIG7 is 3840
[    2.229661] CS1 is not enabled, so continuing...
[    2.234309] Value of GPMC_CS_CONFIG7 is 3840
[    2.238593] CS2 is not enabled, so continuing...
[    2.243240] Value of GPMC_CS_CONFIG7 is 3840
[    2.247525] CS3 is not enabled, so continuing...
[    2.252158] Value of GPMC_CS_CONFIG7 is 3840
[    2.256456] CS4 is not enabled, so continuing...
[    2.261090] Value of GPMC_CS_CONFIG7 is 3840
[    2.265388] CS5 is not enabled, so continuing...
[    2.270021] Value of GPMC_CS_CONFIG7 is 3840
[    2.274319] CS6 is not enabled, so continuing...
[    2.278954] 
[    2.278954] 
[    2.278954] 
[    2.278954] Srini debug @ line 2809 in function gpmc_gpio_init in file drivers/memory/omap-gpmc.c
[    2.278954] 
[    2.278954] 
[    2.295723] gpmc_gpio_init is success!!!
[    2.299665] 
[    2.299665] 
[    2.299665] 
[    2.299665] Srini debug @ line 1653 in function gpmc_setup_irq in file drivers/memory/omap-gpmc.c
[    2.299665] 
[    2.299665] 
[    2.316089] gpmc_setup_irq is success!!!
[    2.320030] 
[    2.320030] 
[    2.320030] 
[    2.320030] Srini debug @ line 2736 in function gpmc_probe_dt_children in file drivers/memory/omap-gpmc.c
[    2.320030] 
[    2.320030] 
[    2.337089] Srini -> child->name is generic
[    2.341293] 
[    2.341293] 
[    2.341293] 
[    2.341293] Srini debug @ line 2438 in function gpmc_probe_generic_child in file drivers/memory/omap-gpmc.c
[    2.341293] 
[    2.341293] 
[    2.358518] Srini -> Value of CS from reg first element child node is 0
[    2.365210] Srini -> Value of name is :(null)
[    2.369586] 
[    2.369586] 
[    2.369586] 
[    2.369586] Srini debug @ line 1323 in function gpmc_cs_request in file drivers/memory/omap-gpmc.c
[    2.369586] 
[    2.369586] 
[    2.386026] 
[    2.386026] 
[    2.386026] 
[    2.386026] Srini debug @ line 1202 in function gpmc_mem_align in file drivers/memory/omap-gpmc.c
[    2.386026] 
[    2.386026] 
[    2.402373] Value of GPMC_CS_CONFIG7 is 3912
[    2.406677] Value of res->start: 134217728 resource_size(res): 16777216
[    2.413333] random: fast init done
[    2.416751] 
[    2.416751] 
[    2.416751] 
[    2.416751] Srini debug @ line 1044 in function gpmc_cs_set_memconf in file drivers/memory/omap-gpmc.c
[    2.416751] 
[    2.416751] 
[    2.433534] Srini -> gpmc_cs_set_memconf success...
[    2.438431] Srini -> Request GPMC CS 0 success
[    2.442891] Child name is nand
[    2.445972] 
[    2.445972] 
[    2.445972] 
[    2.445972] Srini debug @ line 2194 in function gpmc_read_settings_dt in file drivers/memory/omap-gpmc.c
[    2.445972] 
[    2.445972] 
[    2.462941] Srini Bool value  of gpmc,sync-read is 0
[    2.467938] Srini Bool value  of gpmc,sync-write is 0
[    2.473022] Srini Bool value  of gpmc,burst-wrap is 0
[    2.478091] Srini Bool value  of gpmc,burst-read is 0
[    2.483174] Srini Bool value  of gpmc,burst-write is 0
[    2.488331] Srini Value  of gpmc,device-width is 1
[    2.493152] Srini Value  of gpmc,mux-add-data is 0
[    2.497965] Srini Value  of gpmc,wait-on-read is 0
[    2.502772] Srini Value  of gpmc,wait-on-write is 0
[    2.507684] 
[    2.507684] 
[    2.507684] 
[    2.507684] Srini debug @ line 2256 in function gpmc_read_timings_dt in file drivers/memory/omap-gpmc.c
[    2.507684] 
[    2.507684] 
[    2.524622] Srini -> minimum clock period for syncronous mode
[    2.530391] Srini -> Value of        &gpmc_t->sync_clk               :0
[    2.530391] 
[    2.536961] Srini -> chip select timtings
[    2.540985] Srini -> Value of        &gpmc_t->cs_on                  :0
[    2.545894] Srini -> Value of        &gpmc_t->cs_rd_off              :44
[    2.551139] Srini -> Value of        &gpmc_t->cs_wr_off              :44
[    2.551139] 
[    2.557880] Srini ->  ADV signal timings
[    2.561818] Srini -> Value of        &gpmc_t->adv_on                 :6
[    2.566814] Srini -> Value of        &gpmc_t->adv_rd_off             :34
[    2.572144] Srini -> Value of        &gpmc_t->adv_wr_off             :44
[    2.577490] Srini -> Value of        &gpmc_t->adv_aad_mux_on         :0
[    2.583098] Srini -> Value of        &gpmc_t->adv_aad_mux_rd_off     :0
[    2.588953] Srini -> Value of        &gpmc_t->adv_aad_mux_wr_off     :0
[    2.588953] 
[    2.596305] Srini ->  WE signal timings
[    2.600153] Srini -> Value of        &gpmc_t->we_on                  :0
[    2.605062] Srini -> Value of        &gpmc_t->we_off                 :40
[    2.605062] 
[    2.611616] Srini -> OE signal timings
[    2.615391] Srini -> Value of        &gpmc_t->oe_on                  :0
[    2.620288] Srini -> Value of        &gpmc_t->oe_off                 :54
[    2.625371] Srini -> Value of        &gpmc_t->oe_aad_mux_on          :0
[    2.630877] Srini -> Value of        &gpmc_t->oe_aad_mux_off         :0
[    2.636484] Srini -> Value of        &gpmc_t->page_burst_access      :0
[    2.642252] Srini -> Value of        &gpmc_t->access                 :64
[    2.647335] Srini -> Value of        &gpmc_t->rd_cycle               :82
[    2.652493] Srini -> Value of        &gpmc_t->wr_cycle               :82
[    2.657663] Srini -> Value of        &gpmc_t->bus_turnaround         :0
[    2.663270] Srini -> Value of        &gpmc_t->cycle2cycle_delay      :0
[    2.669039] Srini -> Value of        &gpmc_t->wait_monitoring        :0
[    2.674645] Srini -> Value of        &gpmc_t->clk_activation         :0
[    2.674645] 
[    2.681723] Srini -> only applicable to OMAP3+
[    2.686197] Srini -> Value of        &gpmc_t->wr_access              :40
[    2.691441] Srini -> Value of        &gpmc_t->wr_data_mux_bus        :0
[    2.691441] 
[    2.698530] Srini -> bool timing parameters
[    2.702729] Srini -> Value of        p->cycle2cyclediffcsen          :0
[    2.708343] Srini -> Value of        p->cycle2cyclesamecsen          :0
[    2.713951] Srini -> Value of        p->we_extra_delay               :0
[    2.719109] Srini -> Value of        p->oe_extra_delay               :0
[    2.724279] Srini -> Value of        p->adv_extra_delay              :0
[    2.729524] Srini -> Value of        p->cs_extra_delay               :0
[    2.734695] Srini -> Value of        p->time_para_granularity        :0
[    2.740291] 
[    2.740291] 
[    2.740291] 
[    2.740291] Srini debug @ line 1260 in function gpmc_cs_remap in file drivers/memory/omap-gpmc.c
[    2.740291] 
[    2.740291] 
[    2.756548] Value of CS is 0
[    2.759440] 
[    2.759440] 
[    2.759440] 
[    2.759440] Srini debug @ line 1149 in function gpmc_cs_get_memconf in file drivers/memory/omap-gpmc.c
[    2.759440] 
[    2.759440] 
[    2.776237] GPMC_REVISION           = 60
[    2.780175] GPMC_SYSCONFIG          = 11
[    2.784127] GPMC_SYSSTATUS          = 1
[    2.787976] GPMC_IRQSTATUS          = 0
[    2.791824] GPMC_IRQENABLE          = 0
[    2.795687] GPMC_TIMEOUT_CONTROL    = 1ff0
[    2.799798] GPMC_ERR_ADDRESS        = 0
[    2.803661] GPMC_ERR_TYPE           = 0
[    2.807510] GPMC_CONFIG             = 12
[    2.811446] GPMC_STATUS             = 101
[    2.815482] GPMC_CONFIG1_0          = 800
[    2.819505] GPMC_CONFIG2_0          = 1e1e00
[    2.823805] GPMC_CONFIG3_0          = 1e1e00
[    2.828090] GPMC_CONFIG4_0          = 16051807
[    2.832548] GPMC_CONFIG5_0          = 151e1e
[    2.836847] GPMC_CONFIG6_0          = 16000f80
[    2.841306] GPMC_CONFIG7_0          = f08
[    2.845347] 
[    2.845347] 
[    2.845347] Srini debug @ line 423 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    2.845347] 
[    2.859071] print_hardware_sfrs
[    2.859071] 
[    2.863723] Value of AD0 at location 0x44e10800 is 0x30
[    2.868969] Value of AD1 at location 0x44e10804 is 0x30
[    2.874229] Value of AD2 at location 0x44e10808 is 0x30
[    2.879474] Value of AD3 at location 0x44e1080c is 0x30
[    2.884733] Value of AD4 at location 0x44e10810 is 0x30
[    2.889978] Value of AD5 at location 0x44e10814 is 0x30
[    2.895237] Value of AD6 at location 0x44e10818 is 0x30
[    2.900483] Value of AD7 at location 0x44e1081c is 0x30
[    2.905742] Value of AD8 at location 0x44e10820 is 0x27
[    2.910987] Value of AD9 at location 0x44e10824 is 0x27
[    2.916247] Value of AD10 at location 0x44e10828 is 0x27
[    2.921580] Value of AD11 at location 0x44e1082c is 0x27
[    2.926926] Value of AD12 at location 0x44e10830 is 0x27
[    2.932258] Value of AD13 at location 0x44e10834 is 0x27
[    2.937605] Value of AD14 at location 0x44e10838 is 0x27
[    2.942938] Value of AD15 at location 0x44e1083c is 0x27
[    2.948282] 
[    2.949778] Value of A16 at location 0x44e108a4 is 0x8
[    2.954950] Value of A17 at location 0x44e108a8 is 0x8
[    2.960107] Value of A18 at location 0x44e108ac is 0x8
[    2.965280] Value of A19 at location 0x44e108b0 is 0x8
[    2.970438] Value of A20 at location 0x44e108b4 is 0x8
[    2.975610] Value of A21 at location 0x44e108b8 is 0x8
[    2.980768] Value of A22 at location 0x44e108bc is 0x8
[    2.985937] 
[    2.987433] Value of A23 at location 0x44e108e0 is 0x0
[    2.992591] Value of A24 at location 0x44e108e4 is 0x0
[    2.997762] Value of A25 at location 0x44e108e8 is 0x0
[    3.002918] 
[    3.004429] Value of A26 at location 0x44e1086c is 0x22
[    3.004429] 
[    3.011159] Value of CS0             at location 0x44e1087c is 0x8
[    3.011159] 
[    3.017901] Value of ALE             at location 0x44e10890 is 0x8
[    3.017901] 
[    3.024733] Value of OEN_REN         at location 0x44e10894 is 0x8
[    3.024733] 
[    3.031811] Value of BEN0_CLE        at location 0x44e1089c is 0x8
[    3.031811] 
[    3.038904] Value of WEN             at location 0x44e10898 is 0x8
[    3.038904] 
[    3.045735] Value of WAIT0           at location 0x44e10870 is 0x30
[    3.045735] 
[    3.052815] 
[    3.052815] 
[    3.052815] Srini debug @ line 487 in function print_hardware_sfrs in file drivers/memory/omap-gpmc.c
[    3.052815] 
[    3.066540] End of print_hardware_sfrs...
[    3.066540] 
[    3.072048] GPMC_CS_CONFIG7 value read : 0xf08
[    3.076524] Value of cs:0 old_base:134217728 base:134217728 size: 16777216
[    3.083439] old_base is equal to base, just returning ...
[    3.088858] gpmc_cs_remap success 
[    3.092279] 
[    3.092279] 
[    3.092279] 
[    3.092279] Srini debug @ line 1400 in function gpmc_configure in file drivers/memory/omap-gpmc.c
[    3.092279] 
[    3.092279] 
[    3.108628] 
[    3.108628] 
[    3.108628] 
[    3.108628] Srini !!! FAILURE !!! @ line 2607 in function gpmc_probe_generic_child in file drivers/memory/omap-gpmc.c
[    3.108628] 
[    3.108628] 
[    3.126727] Not Reserving wait pins .....
[    3.130753] gpmc cs0 before gpmc_cs_program_settings:
[    3.135838] cs0 GPMC_CS_CONFIG1: 0x00000800
[    3.140038] cs0 GPMC_CS_CONFIG2: 0x001e1e00
[    3.144251] cs0 GPMC_CS_CONFIG3: 0x001e1e00
[    3.148450] cs0 GPMC_CS_CONFIG4: 0x16051807
[    3.152648] cs0 GPMC_CS_CONFIG5: 0x00151e1e
[    3.156862] cs0 GPMC_CS_CONFIG6: 0x16000f80
[    3.161059] gpmc cs0 access configuration:
[    3.165188] gpmc,mux-add-data = <0>;
[    3.168776] gpmc,device-width = <1>;
[    3.172364] gpmc,wait-pin = <0>;
[    3.175618] gpmc,burst-length = <4>;
[    3.179211] gpmc,cycle2cycle-samecsen = <1>;
[    3.183511] gpmc cs0 timings configuration:
[    3.187716] gpmc,cs-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.193328] gpmc,cs-rd-off-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.199885] gpmc,cs-wr-off-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.206456] gpmc,adv-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.212140] gpmc,adv-rd-off-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.218799] gpmc,adv-wr-off-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.225458] gpmc,adv-aad-mux-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.231841] gpmc,adv-aad-mux-rd-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.238586] gpmc,adv-aad-mux-wr-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.245331] gpmc,oe-on-ns = <70>; /* 61 ns - 70 ns; 7 ticks */
[    3.251190] gpmc,oe-off-ns = <240>; /* 231 ns - 240 ns; 24 ticks */
[    3.257500] gpmc,oe-aad-mux-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.263811] gpmc,oe-aad-mux-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.270192] gpmc,we-on-ns = <50>; /* 41 ns - 50 ns; 5 ticks */
[    3.276066] gpmc,we-off-ns = <220>; /* 211 ns - 220 ns; 22 ticks */
[    3.282361] gpmc,rd-cycle-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.288845] gpmc,wr-cycle-ns = <300>; /* 291 ns - 300 ns; 30 ticks */
[    3.295330] gpmc,access-ns = <210>; /* 201 ns - 210 ns; 21 ticks */
[    3.301625] gpmc,page-burst-access-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.308284] gpmc,bus-turnaround-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.314681] gpmc,cycle2cycle-delay-ns = <150>; /* 141 ns - 150 ns; 15 ticks */
[    3.321935] gpmc,wait-monitoring-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.328417] gpmc,clk-activation-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.334814] gpmc,wr-data-mux-bus-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.341284] gpmc,wr-access-ns = <220>; /* 211 ns - 220 ns; 22 ticks */
[    3.347853] 
[    3.347853] 
[    3.347853] 
[    3.347853] Srini debug @ line 2097 in function gpmc_cs_program_settings in file drivers/memory/omap-gpmc.c
[    3.347853] 
[    3.347853] 
[    3.365073] gpmc_cs_program_settings Success !!!!
[    3.369803] GPMC CS0: cs_on            :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.377336] GPMC CS0: cs_rd_off        :   5 ticks,  50 ns (was  30 ticks)  44 ns
[    3.384868] GPMC CS0: cs_wr_off        :   5 ticks,  50 ns (was  30 ticks)  44 ns
[    3.392385] GPMC CS0: adv_on           :   1 ticks,  10 ns (was   0 ticks)   6 ns
[    3.399915] GPMC CS0: adv_rd_off       :   4 ticks,  40 ns (was  30 ticks)  34 ns
[    3.407446] GPMC CS0: adv_wr_off       :   5 ticks,  50 ns (was  30 ticks)  44 ns
[    3.414978] GPMC CS0: adv_aad_mux_on   :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.422493] GPMC CS0: adv_aad_mux_rd_off:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.430110] GPMC CS0: adv_aad_mux_wr_off:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.437728] GPMC CS0: oe_on            :   0 ticks,   0 ns (was   7 ticks)   0 ns
[    3.445260] GPMC CS0: oe_off           :   6 ticks,  60 ns (was  24 ticks)  54 ns
[    3.452777] GPMC CS0: oe_aad_mux_on    :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.460308] GPMC CS0: oe_aad_mux_off   :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.467838] GPMC CS0: we_on            :   0 ticks,   0 ns (was   5 ticks)   0 ns
[    3.475369] GPMC CS0: we_off           :   4 ticks,  40 ns (was  22 ticks)  40 ns
[    3.482885] GPMC CS0: rd_cycle         :   9 ticks,  90 ns (was  30 ticks)  82 ns
[    3.490416] GPMC CS0: wr_cycle         :   9 ticks,  90 ns (was  30 ticks)  82 ns
[    3.497949] GPMC CS0: access           :   7 ticks,  70 ns (was  21 ticks)  64 ns
[    3.505481] GPMC CS0: page_burst_access:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.513012] GPMC CS0: bus_turnaround   :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.520528] GPMC CS0: cycle2cycle_delay:   0 ticks,   0 ns (was  15 ticks)   0 ns
[    3.528059] GPMC CS0: wr_data_mux_bus  :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.535592] GPMC CS0: wr_access        :   4 ticks,  40 ns (was  22 ticks)  40 ns
[    3.543124] GPMC CS0: wait_monitoring  :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.550640] GPMC CS0: clk_activation   :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    3.558169] GPMC CS0 CLK period is 10 ns (div 1)
[    3.562807] gpmc cs0 after gpmc_cs_set_timings:
[    3.567369] cs0 GPMC_CS_CONFIG1: 0x00000800
[    3.571569] cs0 GPMC_CS_CONFIG2: 0x00050500
[    3.575781] cs0 GPMC_CS_CONFIG3: 0x00050401
[    3.579980] cs0 GPMC_CS_CONFIG4: 0x04000600
[    3.584192] cs0 GPMC_CS_CONFIG5: 0x00070909
[    3.588391] cs0 GPMC_CS_CONFIG6: 0x04000000
[    3.592588] gpmc cs0 access configuration:
[    3.596714] gpmc,mux-add-data = <0>;
[    3.600302] gpmc,device-width = <1>;
[    3.603904] gpmc,wait-pin = <0>;
[    3.607145] gpmc,burst-length = <4>;
[    3.610734] gpmc cs0 timings configuration:
[    3.614950] gpmc,cs-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.620547] gpmc,cs-rd-off-ns = <50>; /* 41 ns - 50 ns; 5 ticks */
[    3.626769] gpmc,cs-wr-off-ns = <50>; /* 41 ns - 50 ns; 5 ticks */
[    3.632991] gpmc,adv-on-ns = <10>; /* 1 ns - 10 ns; 1 ticks */
[    3.638849] gpmc,adv-rd-off-ns = <40>; /* 31 ns - 40 ns; 4 ticks */
[    3.645158] gpmc,adv-wr-off-ns = <50>; /* 41 ns - 50 ns; 5 ticks */
[    3.651453] gpmc,adv-aad-mux-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.657848] gpmc,adv-aad-mux-rd-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.664593] gpmc,adv-aad-mux-wr-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.671322] gpmc,oe-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.676933] gpmc,oe-off-ns = <60>; /* 51 ns - 60 ns; 6 ticks */
[    3.682879] gpmc,oe-aad-mux-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.689189] gpmc,oe-aad-mux-off-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.695585] gpmc,we-on-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.701183] gpmc,we-off-ns = <40>; /* 31 ns - 40 ns; 4 ticks */
[    3.707143] gpmc,rd-cycle-ns = <90>; /* 81 ns - 90 ns; 9 ticks */
[    3.713278] gpmc,wr-cycle-ns = <90>; /* 81 ns - 90 ns; 9 ticks */
[    3.719399] gpmc,access-ns = <70>; /* 61 ns - 70 ns; 7 ticks */
[    3.725358] gpmc,page-burst-access-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.732003] gpmc,bus-turnaround-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.738398] gpmc,cycle2cycle-delay-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.745057] gpmc,wait-monitoring-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.751526] gpmc,clk-activation-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.757921] gpmc,wr-data-mux-bus-ns = <0>; /* 0 ns - 0 ns; 0 ticks */
[    3.764406] gpmc,wr-access-ns = <40>; /* 31 ns - 40 ns; 4 ticks */
[    3.770610] gpmc_cs_set_timings Success !!!!
[    3.776216] nand: Srini -> device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    3.783465] nand: Micron MT29F2G08ABAEAWP
[    3.787496] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.795167] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    3.800727] 8 ofpart partitions found on MTD device omap2-nand.0
[    3.806792] Creating 8 MTD partitions on "omap2-nand.0":
[    3.812159] 0x000000000000-0x000000020000 : "NAND.SPL"
[    3.818656] 0x000000020000-0x000000040000 : "NAND.SPL.backup1"
[    3.825660] 0x000000040000-0x000000060000 : "NAND.SPL.backup2"
[    3.832513] 0x000000060000-0x000000080000 : "NAND.SPL.backup3"
[    3.839414] 0x000000080000-0x000000260000 : "NAND.u-boot"
[    3.847533] 0x000000260000-0x000000280000 : "NAND.u-boot-env"
[    3.854363] 0x000000280000-0x000000780000 : "NAND.kernel"
[    3.865442] 0x000000780000-0x000010000000 : "NAND.file-system"
[    4.107050] of_platform_device_create Success !!!!
[    4.111881] of_match_node Success !!!!
[    4.117334] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[    4.124267] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 400 kHz
[    4.153323] tps65910 2-002d: No interrupt support, no core IRQ
[    4.161420] vrtc: supplied by vbat
[    4.168705] vio: supplied by vbat
[    4.173590] vdd1: supplied by vbat
[    4.178839] vdd2: supplied by vbat
[    4.185625] vdig1: supplied by vbat
[    4.190520] vdig2: supplied by vbat
[    4.195471] vpll: supplied by vbat
[    4.200285] vdac: supplied by vbat
[    4.205135] vaux1: supplied by vbat
[    4.210028] vaux2: supplied by vbat
[    4.214985] vaux33: supplied by vbat
[    4.219994] vmmc: supplied by vbat
[    4.224874] vbb: supplied by vbat
[    4.229475] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz
[    4.235869] hctosys: unable to open rtc device (rtc0)
[    4.241832] ALSA device list:
[    4.244888]   No soundcards found.
[    4.250918] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem
[    4.260735] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[    4.268255] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[    4.285907] EXT4-fs (mmcblk0p2): recovery complete
[    4.386611] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    4.394863] VFS: Mounted root (ext3 filesystem) readonly on device 179:2.
[    4.405847] devtmpfs: mounted
[    4.410496] Freeing unused kernel memory: 1024K
[    4.857201] systemd[1]: System time before build time, advancing clock.
[    4.924826] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPT)
[    4.946556] systemd[1]: Detected architecture arm.

Welcome to Arago 2018.10!

[    4.984518] systemd[1]: Set hostname to <am335x-evm>.
[    5.656941] random: systemd: uninitialized urandom read (16 bytes read)
[    5.664343] systemd[1]: Listening on Syslog Socket.
[  OK  ] Listening on Syslog Socket.
[    5.693361] random: systemd: uninitialized urandom read (16 bytes read)
[    5.700164] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    5.733264] random: systemd: uninitialized urandom read (16 bytes read)
[    5.740326] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    5.783636] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    5.816512] systemd[1]: Created slice System Slice.
[  OK  ] Created slice System Slice.
[    5.849518] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[    5.895740] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Listening on udev Control Socket.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Reached target Paths.
         Mounting Kernel Debug File System...
[  OK  ] Created slice system-getty.slice.
[  OK  ] Listening on Process Core Dump Socket.
[  OK  ] Reached target Swap.
         Mounting Temporary Directory (/tmp)...
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Listening on Network Service Netlink Socket.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket.
         Starting File System Check on Root Device...
         Starting Load Kernel Modules...
         Starting Create list of required st��…ce nodes for the current kernel...
         Starting Journal Service...
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Mounted Temporary Directory (/tmp).
[  OK  ] Started Create list of required sta��…vice nodes for the current kernel.
[    6.600502] cryptodev: loading out-of-tree module taints kernel.
[    6.619363] cryptodev: driver 1.9 loaded.
[  OK  ] Started Load Kernel Modules.
         Starting Apply Kernel Variables...
         Mounting Kernel Configuration File System...
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Journal Service.
[   31.721422] random: crng init doneing for dev-ttyS0.device (25s / 1min 30s)
[   31.724879] random: 7 urandom warning(s) missed due to ratelimiting
[  OK  ] Started File System Check on Root Device.
         Starting Remount Root and Kernel File Systems...
[   33.179056] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[  OK  ] Started Remount Root and Kernel File Systems.
         Starting udev Coldplug all Devices...
         Starting Create Static Device Nodes in /dev...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Create Static Device Nodes in /dev.
[   33.508983] systemd-journald[68]: Received request to flush runtime journal from PID 1
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /media/ram...
         Mounting /var/volatile...
         Starting udev Kernel Device Manager...
[  OK  ] Mounted /var/volatile.
[  OK  ] Mounted /media/ram.
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started udev Kernel Device Manager.
         Starting Load/Save Random Seed...
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
         Starting Network Time Synchronization...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Created slice system-systemd\x2dbacklight.sli[   36.029096] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
ce.
         Starting Load/Save Screen Backlight��…ightness of backlight:backlight...
[  OK  ] Found device /dev/ttyS0.
[   36.260844] omap_rtc 44e3e000.rtc: registered as rtc0
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Load/Save Screen Backlight Brightness of backlight:backlight.
[  OK  ] Reached target System Initialization.
         Starting Network Service...
[   36.666668] CAN device driver interface
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Started Daily rotation of log files.
[   36.755753] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=38)
[  OK  ] Listening on RPCbind Server Activation Socket[   36.905283] c_can_platform 481d0000.can: c_can_platform device registered ()
.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Reached target Containers.
         Starting Print notice about GPLv3 packages...
         Starting telnetd.service...
[  OK  ] Started Job spooling tools.
[  OK  ] Started Hardware RNG Entropy Gatherer Daemon.
         Starting Login Service...
[   37.736314] ti_emif_sram 4c000000.emif: Unable to get sram pool for ocmcram data
[  OK  ] Started Periodic Command Scheduler.
         Starting RPC Bind Service...
[  OK  ] Started Kernel Logging Service.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timers.
[   38.158384] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[  OK  ] Started System Logging Service.
[   38.455186] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[  OK  ] Started D-Bus System Message Bus.
[   38.515418] omap-aes 53500000.aes: will run requests pump with realtime priority
[  OK  ] Started telnetd.service.
[   39.706383] remoteproc remoteproc0: wkup_m3 is available
[   39.837621] remoteproc remoteproc0: powering up wkup_m3
[  OK  ] Started RPC Bind Service.
[   39.894098] PM: Cannot get wkup_m3_ipc handle
[   39.965937] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 224628
[  OK  ] Started Network Service.
[  OK  ] Found device /dev/ttyS3.
[   40.133476] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192
[   40.246485] remoteproc remoteproc0: remote processor wkup_m3 is now up
[   40.372934] net eth0: initializing cpsw version 1.12 (0)
[   40.375023] libphy: PHY 4a101000.mdio:01 not found
[   40.375037] net eth0: phy "4a101000.mdio:01" not found on slave 0, err -19
[   40.375048] libphy: PHY 4a101000.mdio:02 not found
[   40.375055] net eth0: phy "4a101000.mdio:02" not found on slave 1, err -19
[   40.472954] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   41.415223] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  OK  ] Started Login Service.
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[  OK  ] Reached target Network.
         Starting Network Name Resolution...
         Starting Permit User Sessions...
         Starting thttpd.service...
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Started Serial Getty on ttyS3.
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
         Starting Synchronize System and HW clocks...
[   45.073574] pm33xx pm33xx: PM: am33xx_pm_alloc_sram: Unable to get sram pool for ocmcram
[   45.083656] input: ti-tsc as /devices/platform/ocp/44e0d000.tscadc/44e0d000.tscadc:tsc/input/input0
[  OK  ] Started thttpd.service.
[  OK  ] Started Synchronize System and HW clocks.
         Starting rng-tools.service...
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Host and Network Name Lookups.
[  OK  ] Started NFS status monitor for NFSv2/3 locking..
[  OK  ] Started rng-tools.service.
         Starting thermal-zone-init.service...
[  OK  ] Started thermal-zone-init.service.
***************************************************************
***************************************************************
NOTICE: This file system contains the following GPLv3 packages:
        bash
        binutils
        cifs-utils
        cpio
        dosfstools
        elfutils
        gawk
        gzip
        libdw1
        libelf1
        libreadline7
        m4
        which

If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution.  This can be done using
the opkg remove command.  i.e.:
    opkg remove <package>
Where <package> is the name printed in the list above

NOTE: If the package is a dependency of another package you
      will be notified of the dependent packages.  You should
      use the --force-removal-of-dependent-packages option to
      also remove the dependent packages as well
***************************************************************
***************************************************************
[  OK  ] Started Print notice about GPLv3 packages.
[   48.045725] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator
[   48.129113] usbcore: registered new interface driver usbfs
[   48.129182] usbcore: registered new interface driver hub
[   48.163990] usbcore: registered new device driver usb
[   48.315703] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[   48.321112] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
[   48.452246] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   48.529905] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   48.603167] usb usb1: Product: MUSB HDRC host driver
[   48.608216] usb usb1: Manufacturer: Linux 4.14.79-ge669d52447 musb-hcd
[   48.701488] usb usb1: SerialNumber: musb-hdrc.0
[   48.754224] hub 1-0:1.0: USB hub found
[   48.793190] hub 1-0:1.0: 1 port detected
[   48.834375] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator
[   49.029351] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[   49.082371] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[   49.128206] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   49.152673] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   49.176769] usb usb2: Product: MUSB HDRC host driver
[   49.181836] usb usb2: Manufacturer: Linux 4.14.79-ge669d52447 musb-hcd
[   49.214378] usb usb2: SerialNumber: musb-hdrc.1
[   49.237076] hub 2-0:1.0: USB hub found
[   49.253157] hub 2-0:1.0: 1 port detected

 _____                    _____           _         _   
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
              |___|                    |___|            

Arago Project http://arago-project.org am335x-evm ttyS0

Arago 2018.10 am335x-evm ttyS0

am335x-evm login: root
root@am335x-evm:~# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00800000 00010000 "NOR User Defined"
mtd1: 00020000 00020000 "NAND.SPL"
mtd2: 00020000 00020000 "NAND.SPL.backup1"
mtd3: 00020000 00020000 "NAND.SPL.backup2"
mtd4: 00020000 00020000 "NAND.SPL.backup3"
mtd5: 001e0000 00020000 "NAND.u-boot"
mtd6: 00020000 00020000 "NAND.u-boot-env"
mtd7: 00500000 00020000 "NAND.kernel"
mtd8: 0f880000 00020000 "NAND.file-system"
root@am335x-evm:~# 
root@am335x-evm:~# 
root@am335x-evm:~# 
root@am335x-evm:~# nandwrite -p /dev/mtd7 zImage
zImage: No such file or directory
nandwrite: error!: Data was only partially written due to error
           error 9 (Bad file descriptor)
root@am335x-evm:~# 
root@am335x-evm:~# cd /run/media/mmcblk0p1/
root@am335x-evm:/run/media/mmcblk0p1# 
root@am335x-evm:/run/media/mmcblk0p1# 
root@am335x-evm:/run/media/mmcblk0p1# nandwrite -p /dev/mtd7 zImage
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000
Writing data to block 3 at offset 0x60000
Writing data to block 4 at offset 0x80000
Writing data to block 5 at offset 0xa0000
Writing data to block 6 at offset 0xc0000
Writing data to block 7 at offset 0xe0000
Writing data to block 8 at offset 0x100000
Writing data to block 9 at offset 0x120000
Writing data to block 10 at offset 0x140000
Writing data to block 11 at offset 0x160000
Writing data to block 12 at offset 0x180000
Writing data to block 13 at offset 0x1a0000
Writing data to block 14 at offset 0x1c0000
Writing data to block 15 at offset 0x1e0000
Writing data to block 16 at offset 0x200000
Writing data to block 17 at offset 0x220000
Writing data to block 18 at offset 0x240000
Writing data to block 19 at offset 0x260000
Writing data to block 20 at offset 0x280000
Writing data to block 21 at offset 0x2a0000
Writing data to block 22 at offset 0x2c0000
Writing data to block 23 at offset 0x2e0000
Writing data to block 24 at offset 0x300000
Writing data to block 25 at offset 0x320000
Writing data to block 26 at offset 0x340000
Writing data to block 27 at offset 0x360000
Writing data to block 28 at offset 0x380000
Writing data to block 29 at offset 0x3a0000
root@am335x-evm:/run/media/mmcblk0p1#

