U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 187 ms (19.3 MiB/s) 97190 bytes read in 19 ms (4.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000346] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000355] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000810] Console: colour dummy device 80x30 [ 0.000828] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000835] This ensures that you still see kernel messages. Please [ 0.000842] update your kernel commandline. [ 0.000860] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000875] pid_max: default: 32768 minimum: 301 [ 0.000993] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001004] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001535] CPU: Testing write buffer coherency: ok [ 0.001573] CPU0: Spectre v2: using ICIALLU workaround [ 0.001774] /cpus/cpu@0 missing clock-frequency property [ 0.001788] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039854] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059862] Hierarchical SRCU implementation. [ 0.080046] EFI services will not be available. [ 0.099920] smp: Bringing up secondary CPUs ... [ 0.099931] smp: Brought up 1 node, 1 CPU [ 0.099941] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099949] CPU: All CPU(s) started in HYP mode. [ 0.099956] CPU: Virtualization extensions available. [ 0.100363] devtmpfs: initialized [ 0.118035] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120075] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120278] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120296] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124107] pinctrl core: initialized pinctrl subsystem [ 0.124615] DMI not present or invalid. [ 0.124858] NET: Registered protocol family 16 [ 0.130811] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131684] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.326834] cpuidle: using governor ladder [ 0.326869] cpuidle: using governor menu [ 0.335289] OMAP GPIO hardware version 0.1 [ 0.362589] No ATAGs? [ 0.362639] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.362653] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.363046] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.363057] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.363604] OMAP DMA hardware revision 0.0 [ 0.402444] edma 43300000.edma: memcpy is disabled [ 0.405587] edma 43300000.edma: TI EDMA DMA engine driver [ 0.412283] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.415793] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.416010] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.416250] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.416493] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.416829] iommu: Adding device 58820000.ipu to group 1 [ 0.416914] iommu: Adding device 55020000.ipu to group 2 [ 0.417066] iommu: Adding device 40800000.dsp to group 0 [ 0.419632] palmas 0-0058: Irq flag is 0x00000004 [ 0.442200] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.443808] SMPS12: supplied by regulator-dummy [ 0.445507] SMPS3: supplied by VMAIN [ 0.447047] SMPS45: supplied by regulator-dummy [ 0.448850] SMPS6: supplied by VMAIN [ 0.450523] SMPS7: supplied by VMAIN [ 0.451935] SMPS8: supplied by VMAIN [ 0.453173] SMPS9: supplied by VMAIN [ 0.454148] LDO1: supplied by VMAIN [ 0.461283] LDO2: supplied by VMAIN [ 0.461688] random: fast init done [ 0.471165] LDO3: supplied by VMAIN [ 0.481174] LDO4: supplied by VMAIN [ 0.491171] LDO5: supplied by regulator-dummy [ 0.491865] LDO6: supplied by regulator-dummy [ 0.492557] LDO7: supplied by regulator-dummy [ 0.493244] LDO8: supplied by regulator-dummy [ 0.493961] LDO9: supplied by VMAIN [ 0.501511] LDOLN: supplied by VMAIN [ 0.511225] LDOUSB: supplied by VMAIN [ 0.524255] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.524527] pps_core: LinuxPPS API ver. 1 registered [ 0.524537] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.524556] PTP clock support registered [ 0.524583] EDAC MC: Ver: 3.0.0 [ 0.530715] dmi: Firmware registration failed. [ 0.531153] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.531363] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.532285] clocksource: Switched to clocksource arch_sys_counter [ 0.539747] NET: Registered protocol family 2 [ 0.540289] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.540328] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.540395] TCP: Hash tables configured (established 4096 bind 4096) [ 0.540453] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.540475] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.540583] NET: Registered protocol family 1 [ 0.560996] RPC: Registered named UNIX socket transport module. [ 0.561006] RPC: Registered udp transport module. [ 0.561014] RPC: Registered tcp transport module. [ 0.561022] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.561981] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.562110] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.563185] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.567284] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.577825] NFS: Registering the id_resolver key type [ 0.577848] Key type id_resolver registered [ 0.577856] Key type id_legacy registered [ 0.577894] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.579548] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.579561] io scheduler noop registered [ 0.579570] io scheduler deadline registered [ 0.579665] io scheduler cfq registered (default) [ 0.579676] io scheduler mq-deadline registered [ 0.579685] io scheduler kyber registered [ 0.584360] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.584510] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.584584] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.584596] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.597930] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.598316] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.598354] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.598380] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.598634] dra7-pcie 51000000.pcie: phy link never came up [ 1.598768] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.598782] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.598793] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.598804] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.599121] PCI: bus0: Fast back to back transfers disabled [ 1.599215] PCI: bus1: Fast back to back transfers enabled [ 1.599253] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.599272] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.599592] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.599716] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.600747] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.603342] V3_3D: supplied by smps9 [ 1.603605] vtt_fixed: supplied by V3_3D [ 1.645429] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.648181] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.682706] console [ttyS0] enabled [ 2.688178] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.695303] DSS: OMAP DSS rev 6.1 [ 2.700364] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.708856] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.719635] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.737461] brd: module loaded [ 2.746081] loop: module loaded [ 2.753352] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.760117] libphy: Fixed MDIO Bus: probed [ 2.765555] i2c /dev entries driver [ 2.775010] sdhci: Secure Digital Host Controller Interface driver [ 2.781356] sdhci: Copyright(c) Pierre Ossman [� U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 187 ms (19.3 MiB/s) 97190 bytes read in 19 ms (4.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000347] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000356] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000801] Console: colour dummy device 80x30 [ 0.000819] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000826] This ensures that you still see kernel messages. Please [ 0.000833] update your kernel commandline. [ 0.000851] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000865] pid_max: default: 32768 minimum: 301 [ 0.000982] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000993] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001524] CPU: Testing write buffer coherency: ok [ 0.001563] CPU0: Spectre v2: using ICIALLU workaround [ 0.001765] /cpus/cpu@0 missing clock-frequency property [ 0.001779] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039853] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059857] Hierarchical SRCU implementation. [ 0.080043] EFI services will not be available. [ 0.099916] smp: Bringing up secondary CPUs ... [ 0.099926] smp: Brought up 1 node, 1 CPU [ 0.099935] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099943] CPU: All CPU(s) started in HYP mode. [ 0.099951] CPU: Virtualization extensions available. [ 0.100355] devtmpfs: initialized [ 0.117999] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120071] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120272] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120290] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124099] pinctrl core: initialized pinctrl subsystem [ 0.124605] DMI not present or invalid. [ 0.124846] NET: Registered protocol family 16 [ 0.130802] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131676] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.326655] cpuidle: using governor ladder [ 0.326691] cpuidle: using governor menu [ 0.335123] OMAP GPIO hardware version 0.1 [ 0.362447] No ATAGs? [ 0.362495] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.362511] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.362904] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.362915] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.363460] OMAP DMA hardware revision 0.0 [ 0.392797] edma 43300000.edma: memcpy is disabled [ 0.395998] edma 43300000.edma: TI EDMA DMA engine driver [ 0.402817] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.406304] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.406513] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.406756] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.406998] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.407338] iommu: Adding device 58820000.ipu to group 1 [ 0.407422] iommu: Adding device 55020000.ipu to group 2 [ 0.407575] iommu: Adding device 40800000.dsp to group 0 [ 0.410266] palmas 0-0058: Irq flag is 0x00000004 [ 0.432529] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.434113] SMPS12: supplied by regulator-dummy [ 0.435815] SMPS3: supplied by VMAIN [ 0.437356] SMPS45: supplied by regulator-dummy [ 0.439147] SMPS6: supplied by VMAIN [ 0.440837] SMPS7: supplied by VMAIN [ 0.442251] SMPS8: supplied by VMAIN [ 0.443495] SMPS9: supplied by VMAIN [ 0.444464] LDO1: supplied by VMAIN [ 0.451603] LDO2: supplied by VMAIN [ 0.452003] random: fast init done [ 0.461481] LDO3: supplied by VMAIN [ 0.471492] LDO4: supplied by VMAIN [ 0.481490] LDO5: supplied by regulator-dummy [ 0.482186] LDO6: supplied by regulator-dummy [ 0.482889] LDO7: supplied by regulator-dummy [ 0.483581] LDO8: supplied by regulator-dummy [ 0.484292] LDO9: supplied by VMAIN [ 0.491827] LDOLN: supplied by VMAIN [ 0.501542] LDOUSB: supplied by VMAIN [ 0.514571] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.514855] pps_core: LinuxPPS API ver. 1 registered [ 0.514865] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.514885] PTP clock support registered [ 0.514912] EDAC MC: Ver: 3.0.0 [ 0.521034] dmi: Firmware registration failed. [ 0.521474] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.521687] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.522616] clocksource: Switched to clocksource arch_sys_counter [ 0.530092] NET: Registered protocol family 2 [ 0.530633] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.530673] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.530741] TCP: Hash tables configured (established 4096 bind 4096) [ 0.530799] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.530821] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.530930] NET: Registered protocol family 1 [ 0.551337] RPC: Registered named UNIX socket transport module. [ 0.551348] RPC: Registered udp transport module. [ 0.551356] RPC: Registered tcp transport module. [ 0.551364] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.552319] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.552447] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.553521] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.557633] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.568178] NFS: Registering the id_resolver key type [ 0.568201] Key type id_resolver registered [ 0.568209] Key type id_legacy registered [ 0.568246] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.569898] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.569912] io scheduler noop registered [ 0.569921] io scheduler deadline registered [ 0.570015] io scheduler cfq registered (default) [ 0.570024] io scheduler mq-deadline registered [ 0.570033] io scheduler kyber registered [ 0.574736] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.574889] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.574963] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.574974] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.588299] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.588686] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.588723] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.588749] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.589003] dra7-pcie 51000000.pcie: phy link never came up [ 1.589136] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.589150] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.589161] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.589172] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.589488] PCI: bus0: Fast back to back transfers disabled [ 1.589582] PCI: bus1: Fast back to back transfers enabled [ 1.589619] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.589638] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.589959] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.590086] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.591119] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.593743] V3_3D: supplied by smps9 [ 1.594010] vtt_fixed: supplied by V3_3D [ 1.635943] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.638681] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.673219] console [ttyS0] enabled [ 2.678702] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.685829] DSS: OMAP DSS rev 6.1 [ 2.690890] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.699382] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.710153] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.727984] brd: module loaded [ 2.736578] loop: module loaded [ 2.743846] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.750618] libphy: Fixed MDIO Bus: probed [ 2.756063] i2c /dev entries driver [ 2.765525] sdhci: Secure Digital Host Controller Interface driver [ 2.771869] sdhci: Copyright(c) Pierre Ossman � U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 187 ms (19.3 MiB/s) 97190 bytes read in 19 ms (4.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000018] Switching to timer-based delay loop, resolution 162ns [ 0.000348] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000357] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000806] Console: colour dummy device 80x30 [ 0.000824] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000831] This ensures that you still see kernel messages. Please [ 0.000838] update your kernel commandline. [ 0.000856] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000871] pid_max: default: 32768 minimum: 301 [ 0.000990] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001002] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001535] CPU: Testing write buffer coherency: ok [ 0.001574] CPU0: Spectre v2: using ICIALLU workaround [ 0.001779] /cpus/cpu@0 missing clock-frequency property [ 0.001793] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039860] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059866] Hierarchical SRCU implementation. [ 0.080051] EFI services will not be available. [ 0.099924] smp: Bringing up secondary CPUs ... [ 0.099935] smp: Brought up 1 node, 1 CPU [ 0.099944] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099952] CPU: All CPU(s) started in HYP mode. [ 0.099959] CPU: Virtualization extensions available. [ 0.100366] devtmpfs: initialized [ 0.118110] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120078] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120283] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120301] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124127] pinctrl core: initialized pinctrl subsystem [ 0.124629] DMI not present or invalid. [ 0.124869] NET: Registered protocol family 16 [ 0.130811] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131674] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.326918] cpuidle: using governor ladder [ 0.326953] cpuidle: using governor menu [ 0.335363] OMAP GPIO hardware version 0.1 [ 0.362682] No ATAGs? [ 0.362731] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.362746] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.363140] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.363152] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.363698] OMAP DMA hardware revision 0.0 [ 0.402444] edma 43300000.edma: memcpy is disabled [ 0.405628] edma 43300000.edma: TI EDMA DMA engine driver [ 0.412492] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.415974] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.416187] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.416429] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.416670] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.417013] iommu: Adding device 58820000.ipu to group 1 [ 0.417098] iommu: Adding device 55020000.ipu to group 2 [ 0.417250] iommu: Adding device 40800000.dsp to group 0 [ 0.419949] palmas 0-0058: Irq flag is 0x00000004 [ 0.442217] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.443809] SMPS12: supplied by regulator-dummy [ 0.445523] SMPS3: supplied by VMAIN [ 0.447080] SMPS45: supplied by regulator-dummy [ 0.448879] SMPS6: supplied by VMAIN [ 0.450551] SMPS7: supplied by VMAIN [ 0.451969] SMPS8: supplied by VMAIN [ 0.453213] SMPS9: supplied by VMAIN [ 0.454192] LDO1: supplied by VMAIN [ 0.461287] LDO2: supplied by VMAIN [ 0.461760] random: fast init done [ 0.471171] LDO3: supplied by VMAIN [ 0.481178] LDO4: supplied by VMAIN [ 0.491187] LDO5: supplied by regulator-dummy [ 0.491891] LDO6: supplied by regulator-dummy [ 0.492601] LDO7: supplied by regulator-dummy [ 0.493299] LDO8: supplied by regulator-dummy [ 0.494011] LDO9: supplied by VMAIN [ 0.501515] LDOLN: supplied by VMAIN [ 0.511227] LDOUSB: supplied by VMAIN [ 0.524264] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.524537] pps_core: LinuxPPS API ver. 1 registered [ 0.524547] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.524567] PTP clock support registered [ 0.524595] EDAC MC: Ver: 3.0.0 [ 0.530715] dmi: Firmware registration failed. [ 0.531153] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.531366] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.532285] clocksource: Switched to clocksource arch_sys_counter [ 0.539761] NET: Registered protocol family 2 [ 0.540306] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.540344] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.540412] TCP: Hash tables configured (established 4096 bind 4096) [ 0.540468] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.540492] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.540599] NET: Registered protocol family 1 [ 0.561004] RPC: Registered named UNIX socket transport module. [ 0.561014] RPC: Registered udp transport module. [ 0.561022] RPC: Registered tcp transport module. [ 0.561030] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.561991] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.562118] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.563189] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.567297] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.577839] NFS: Registering the id_resolver key type [ 0.577868] Key type id_resolver registered [ 0.577877] Key type id_legacy registered [ 0.577915] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.579567] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.579580] io scheduler noop registered [ 0.579590] io scheduler deadline registered [ 0.579686] io scheduler cfq registered (default) [ 0.579695] io scheduler mq-deadline registered [ 0.579704] io scheduler kyber registered [ 0.584417] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.584570] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.584644] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.584655] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.598008] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.598395] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.598430] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.598456] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.598710] dra7-pcie 51000000.pcie: phy link never came up [ 1.598843] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.598857] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.598868] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.598879] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.599193] PCI: bus0: Fast back to back transfers disabled [ 1.599285] PCI: bus1: Fast back to back transfers enabled [ 1.599324] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.599343] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.599668] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.599794] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.600815] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.603429] V3_3D: supplied by smps9 [ 1.603695] vtt_fixed: supplied by V3_3D [ 1.645334] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.648070] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.682644] console [ttyS0] enabled [ 2.688130] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.695258] DSS: OMAP DSS rev 6.1 [ 2.700322] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.708815] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.719586] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.737428] brd: module loaded [ 2.746019] loop: module loaded [ 2.753298] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.760070] libphy: Fixed MDIO Bus: probed [ 2.765497] i2c /dev entries driver [ 2.774952] sdhci: Secure Digital Host Controller Interface driver [ 2.781294] sdhci: Copyright(c) Pierre Ossman [ 2.786801] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.792941] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.798353] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 2.805045] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode [ 2.872725] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.919762] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.929932] mmc0: new high speed SDHC card at address 59b4 [ 2.935826] mmcblk0: mmc0:59b4 00000 14.9 GiB [ 2.941838] mmcblk0: p1 p2 [ 2.944675] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.945999] ledtrig-cpu: registered to indicate activity on CPUs [ 2.955368] NET: Registered protocol family 10 [ 2.966450] Segment Routing with IPv6 [ 2.966497] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.966890] NET: Registered protocol family 17 [ 2.967068] Key type dns_resolver registered [ 2.967179] omap_voltage_late_init: Voltage driver support not added [ 2.967182] Power Management for TI OMAP4+ devices. [ 2.967398] Registering SWP/SWPB emulation handler [ 3.015261] dmm 4e000000.dmm: workaround for errata i878 in use [ 3.121300] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.142292] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003 [ 3.151376] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.172288] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000 [ 3.181285] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=1 F=11)0x2902b [ 3.212288] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=0)0x29000 [ 3.221284] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.252288] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000 [ 3.261285] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.282290] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.291200] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=4)0x29004 [ 3.322287] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=5)0x29005 [ 3.331370] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002 [ 3.362288] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000 [ 3.371198] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=7)0x29007 [ 3.392288] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.401197] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.432288] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001 [ 3.441284] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.462290] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.471199] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.502287] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.511197] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.532288] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.541196] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.572288] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.581196] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.612288] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.621197] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.648292] mmc1: new DDR MMC card at address 0001 [ 3.662546] mmcblk1: mmc1:0001 DG4032 29.1 GiB [ 3.667209] mmcblk1boot0: mmc1:0001 DG4032 partition 1 4.00 MiB [ 3.682404] mmcblk1boot1: mmc1:0001 DG4032 partition 2 4.00 MiB [ 3.692303] mmcblk1rpmb: mmc1:0001 DG4032 partition 3 4.00 MiB U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 188 ms (19.2 MiB/s) 97190 bytes read in 19 ms (4.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000345] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000354] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000804] Console: colour dummy device 80x30 [ 0.000821] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000829] This ensures that you still see kernel messages. Please [ 0.000835] update your kernel commandline. [ 0.000853] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000868] pid_max: default: 32768 minimum: 301 [ 0.000987] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000998] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001529] CPU: Testing write buffer coherency: ok [ 0.001570] CPU0: Spectre v2: using ICIALLU workaround [ 0.001769] /cpus/cpu@0 missing clock-frequency property [ 0.001783] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039852] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059859] Hierarchical SRCU implementation. [ 0.080042] EFI services will not be available. [ 0.099915] smp: Bringing up secondary CPUs ... [ 0.099925] smp: Brought up 1 node, 1 CPU [ 0.099935] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099942] CPU: All CPU(s) started in HYP mode. [ 0.099949] CPU: Virtualization extensions available. [ 0.100359] devtmpfs: initialized [ 0.118042] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120076] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120278] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120295] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124102] pinctrl core: initialized pinctrl subsystem [ 0.124610] DMI not present or invalid. [ 0.124848] NET: Registered protocol family 16 [ 0.130800] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131673] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.325629] cpuidle: using governor ladder [ 0.325663] cpuidle: using governor menu [ 0.334089] OMAP GPIO hardware version 0.1 [ 0.361401] No ATAGs? [ 0.361449] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.361462] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.361884] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.361894] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.362438] OMAP DMA hardware revision 0.0 [ 0.392628] edma 43300000.edma: memcpy is disabled [ 0.395790] edma 43300000.edma: TI EDMA DMA engine driver [ 0.402582] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.406078] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.406292] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.406535] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.406778] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.407111] iommu: Adding device 58820000.ipu to group 1 [ 0.407197] iommu: Adding device 55020000.ipu to group 2 [ 0.407351] iommu: Adding device 40800000.dsp to group 0 [ 0.409909] palmas 0-0058: Irq flag is 0x00000004 [ 0.432354] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.433935] SMPS12: supplied by regulator-dummy [ 0.435635] SMPS3: supplied by VMAIN [ 0.437179] SMPS45: supplied by regulator-dummy [ 0.438969] SMPS6: supplied by VMAIN [ 0.440647] SMPS7: supplied by VMAIN [ 0.442057] SMPS8: supplied by VMAIN [ 0.443289] SMPS9: supplied by VMAIN [ 0.444259] LDO1: supplied by VMAIN [ 0.451448] LDO2: supplied by VMAIN [ 0.461044] random: fast init done [ 0.461325] LDO3: supplied by VMAIN [ 0.471333] LDO4: supplied by VMAIN [ 0.481329] LDO5: supplied by regulator-dummy [ 0.482025] LDO6: supplied by regulator-dummy [ 0.482721] LDO7: supplied by regulator-dummy [ 0.483415] LDO8: supplied by regulator-dummy [ 0.484133] LDO9: supplied by VMAIN [ 0.491663] LDOLN: supplied by VMAIN [ 0.501383] LDOUSB: supplied by VMAIN [ 0.514417] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.514700] pps_core: LinuxPPS API ver. 1 registered [ 0.514710] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.514730] PTP clock support registered [ 0.514758] EDAC MC: Ver: 3.0.0 [ 0.520869] dmi: Firmware registration failed. [ 0.521307] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.521520] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.522440] clocksource: Switched to clocksource arch_sys_counter [ 0.529908] NET: Registered protocol family 2 [ 0.530459] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.530498] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.530565] TCP: Hash tables configured (established 4096 bind 4096) [ 0.530623] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.530645] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.530753] NET: Registered protocol family 1 [ 0.551160] RPC: Registered named UNIX socket transport module. [ 0.551171] RPC: Registered udp transport module. [ 0.551178] RPC: Registered tcp transport module. [ 0.551186] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.552135] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.552263] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.553336] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.557453] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.567998] NFS: Registering the id_resolver key type [ 0.568021] Key type id_resolver registered [ 0.568029] Key type id_legacy registered [ 0.568067] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.569725] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.569737] io scheduler noop registered [ 0.569746] io scheduler deadline registered [ 0.569842] io scheduler cfq registered (default) [ 0.569852] io scheduler mq-deadline registered [ 0.569860] io scheduler kyber registered [ 0.574591] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.574745] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.574820] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.574831] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.588258] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.588643] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.588679] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.588705] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.588959] dra7-pcie 51000000.pcie: phy link never came up [ 1.589092] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.589106] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.589117] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.589128] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.589442] PCI: bus0: Fast back to back transfers disabled [ 1.589535] PCI: bus1: Fast back to back transfers enabled [ 1.589573] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.589593] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.589919] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.590044] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.591071] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.593692] V3_3D: supplied by smps9 [ 1.593953] vtt_fixed: supplied by V3_3D [ 1.635841] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.638588] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.673125] console [ttyS0] enabled [ 2.678607] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.685734] DSS: OMAP DSS rev 6.1 [ 2.690783] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.699269] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.710058] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.727862] brd: module loaded [ 2.736453] loop: module loaded [ 2.743766] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.750532] libphy: Fixed MDIO Bus: probed [ 2.755967] i2c /dev entries driver [ 2.765393] sdhci: Secure Digital Host Controller Interface driver [ 2.771738] sdhci: Copyright(c) Pierre Ossman [ 2.777239] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.783379] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.788793] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 2.795486] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode [ 2.862877] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.909920] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.920092] mmc0: new high speed SDHC card at address 59b4 [ 2.925986] mmcblk0: mmc0:59b4 00000 14.9 GiB [ 2.932008] mmcblk0: p1 p2 [ 2.934845] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.936169] ledtrig-cpu: registered to indicate activity on CPUs [ 2.945549] NET: Registered protocol family 10 [ 2.956633] Segment Routing with IPv6 [ 2.956680] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.957072] NET: Registered protocol family 17 [ 2.957254] Key type dns_resolver registered [ 2.957365] omap_voltage_late_init: Voltage driver support not added [ 2.957368] Power Management for TI OMAP4+ devices. [ 2.957582] Registering SWP/SWPB emulation handler [ 3.005512] dmm 4e000000.dmm: workaround for errata i878 in use [ 3.111484] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.132448] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003 [ 3.141533] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.162443] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000 [ 3.171440] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=1 F=11)0x2902b [ 3.202443] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=0)0x29000 [ 3.211439] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.242443] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000 [ 3.251440] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.272446] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.281355] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=4)0x29004 [ 3.312443] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=5)0x29005 [ 3.321526] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002 [ 3.352443] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000 [ 3.361353] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=7)0x29007 [ 3.382442] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.391351] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.422443] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001 [ 3.431440] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.452443] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.461351] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.492442] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.501351] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.522443] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.531352] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.562442] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.571352] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.602443] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.611351] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.638688] mmc1: new DDR MMC card at address 0001 [ 3.652700] mmcblk1: mmc1:0001 DG4032 29.1 GiB [ 3.657363] mmcblk1boot0: mmc1:0001 DG4032 partition 1 4.00 MiB [ 3.672558] mmcblk1boot1: mmc1:0001 DG4032 partition 2 4.00 MiB [ 3.682459] mmcblk1rpmb: mmc1:0001 DG4032 partition 3 4.00 MiB �� U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 187 ms (19.3 MiB/s) 97190 bytes read in 19 ms (4.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000346] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000355] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000804] Console: colour dummy device 80x30 [ 0.000823] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000830] This ensures that you still see kernel messages. Please [ 0.000837] update your kernel commandline. [ 0.000855] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000870] pid_max: default: 32768 minimum: 301 [ 0.000989] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001532] CPU: Testing write buffer coherency: ok [ 0.001572] CPU0: Spectre v2: using ICIALLU workaround [ 0.001775] /cpus/cpu@0 missing clock-frequency property [ 0.001789] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039855] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059863] Hierarchical SRCU implementation. [ 0.080048] EFI services will not be available. [ 0.099921] smp: Bringing up secondary CPUs ... [ 0.099931] smp: Brought up 1 node, 1 CPU [ 0.099941] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099948] CPU: All CPU(s) started in HYP mode. [ 0.099955] CPU: Virtualization extensions available. [ 0.100357] devtmpfs: initialized [ 0.118002] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120079] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120280] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120296] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124088] pinctrl core: initialized pinctrl subsystem [ 0.124596] DMI not present or invalid. [ 0.124836] NET: Registered protocol family 16 [ 0.130812] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131686] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.326651] cpuidle: using governor ladder [ 0.326686] cpuidle: using governor menu [ 0.335116] OMAP GPIO hardware version 0.1 [ 0.362435] No ATAGs? [ 0.362483] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.362497] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.362896] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.362907] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.363453] OMAP DMA hardware revision 0.0 [ 0.392784] edma 43300000.edma: memcpy is disabled [ 0.395949] edma 43300000.edma: TI EDMA DMA engine driver [ 0.402737] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.406219] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.406431] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.406671] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.406914] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.407258] iommu: Adding device 58820000.ipu to group 1 [ 0.407342] iommu: Adding device 55020000.ipu to group 2 [ 0.407495] iommu: Adding device 40800000.dsp to group 0 [ 0.410181] palmas 0-0058: Irq flag is 0x00000004 [ 0.432507] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.434093] SMPS12: supplied by regulator-dummy [ 0.435800] SMPS3: supplied by VMAIN [ 0.437342] SMPS45: supplied by regulator-dummy [ 0.439136] SMPS6: supplied by VMAIN [ 0.440818] SMPS7: supplied by VMAIN [ 0.442243] SMPS8: supplied by VMAIN [ 0.443479] SMPS9: supplied by VMAIN [ 0.444451] LDO1: supplied by VMAIN [ 0.451617] LDO2: supplied by VMAIN [ 0.451968] random: fast init done [ 0.461491] LDO3: supplied by VMAIN [ 0.471500] LDO4: supplied by VMAIN [ 0.481498] LDO5: supplied by regulator-dummy [ 0.482196] LDO6: supplied by regulator-dummy [ 0.482896] LDO7: supplied by regulator-dummy [ 0.483584] LDO8: supplied by regulator-dummy [ 0.484300] LDO9: supplied by VMAIN [ 0.491832] LDOLN: supplied by VMAIN [ 0.501554] LDOUSB: supplied by VMAIN [ 0.514587] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.514862] pps_core: LinuxPPS API ver. 1 registered [ 0.514872] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.514891] PTP clock support registered [ 0.514919] EDAC MC: Ver: 3.0.0 [ 0.521040] dmi: Firmware registration failed. [ 0.521480] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.521692] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.522615] clocksource: Switched to clocksource arch_sys_counter [ 0.530070] NET: Registered protocol family 2 [ 0.530608] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.530647] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.530715] TCP: Hash tables configured (established 4096 bind 4096) [ 0.530771] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.530793] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.530902] NET: Registered protocol family 1 [ 0.551308] RPC: Registered named UNIX socket transport module. [ 0.551318] RPC: Registered udp transport module. [ 0.551326] RPC: Registered tcp transport module. [ 0.551334] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.552295] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.552424] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.553493] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.557611] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.568157] NFS: Registering the id_resolver key type [ 0.568180] Key type id_resolver registered [ 0.568188] Key type id_legacy registered [ 0.568226] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.569880] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.569892] io scheduler noop registered [ 0.569901] io scheduler deadline registered [ 0.569996] io scheduler cfq registered (default) [ 0.570006] io scheduler mq-deadline registered [ 0.570014] io scheduler kyber registered [ 0.574723] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.574877] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.574952] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.574964] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.588318] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.588708] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.588745] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.588771] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.589025] dra7-pcie 51000000.pcie: phy link never came up [ 1.589156] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.589170] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.589181] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.589192] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.589509] PCI: bus0: Fast back to back transfers disabled [ 1.589602] PCI: bus1: Fast back to back transfers enabled [ 1.589642] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.589660] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.589983] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.590108] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.591130] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.593737] V3_3D: supplied by smps9 [ 1.594002] vtt_fixed: supplied by V3_3D [ 1.635782] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.638513] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.673058] console [ttyS0] enabled [ 2.678540] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.685669] DSS: OMAP DSS rev 6.1 [ 2.690738] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.699227] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.710012] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.727852] brd: module loaded [ 2.736455] loop: module loaded [ 2.743727] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.750495] libphy: Fixed MDIO Bus: probed [ 2.755931] i2c /dev entries driver [ 2.765400] sdhci: Secure Digital Host Controller Interface driver [ 2.771744] sdhci: Copyright(c) Pierre Ossman [ 2.777236] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.783374] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.788782] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 2.795474] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode [ 2.863052] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.910063] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.920233] mmc0: new high speed SDHC card at address 59b4 [ 2.926129] mmcblk0: mmc0:59b4 00000 14.9 GiB [ 2.932128] mmcblk0: p1 p2 [ 2.934966] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.936284] ledtrig-cpu: registered to indicate activity on CPUs [ 2.945661] NET: Registered protocol family 10 [ 2.956749] Segment Routing with IPv6 [ 2.956795] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.957189] NET: Registered protocol family 17 [ 2.957369] Key type dns_resolver registered [ 2.957479] omap_voltage_late_init: Voltage driver support not added [ 2.957482] Power Management for TI OMAP4+ devices. [ 2.957698] Registering SWP/SWPB emulation handler [ 3.005569] dmm 4e000000.dmm: workaround for errata i878 in use [ 3.111528] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.132623] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003 [ 3.141707] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.162619] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000 [ 3.171616] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=1 F=11)0x2902b [ 3.202618] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=0)0x29000 [ 3.211615] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.242618] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000 [ 3.251615] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.272621] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.281530] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=4)0x29004 [ 3.312618] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=5)0x29005 [ 3.321702] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002 [ 3.352619] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000 [ 3.361528] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=7)0x29007 [ 3.382618] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.391526] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.422619] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001 [ 3.431614] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.452620] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.461529] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.492618] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.501527] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.522620] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.531529] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.562618] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.571528] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.602618] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.611526] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.637623] mmc1: new DDR MMC card at address 0001 [ 3.652704] mmcblk1: mmc1:0001 DG4032 29.1 GiB [ 3.657367] mmcblk1boot0: mmc1:0001 DG4032 partition 1 4.00 MiB [ 3.672733] mmcblk1boot1: mmc1:0001 DG4032 partition 2 4.00 MiB [ 3.678786] mmcblk1rpmb: mmc1:0001 DG4032 partition 3 4.00 MiB �� U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5718 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! __led_init: failed requesting GPIO1! GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3785216 bytes read in 188 ms (19.2 MiB/s) 97190 bytes read in 20 ms (4.6 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffba5 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc104a618 ( 298 kB) [ 0.000000] .bss : 0xc104c000 - 0xc1091c60 ( 280 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000350] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000359] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000813] Console: colour dummy device 80x30 [ 0.000830] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000838] This ensures that you still see kernel messages. Please [ 0.000845] update your kernel commandline. [ 0.000863] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000877] pid_max: default: 32768 minimum: 301 [ 0.000997] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001008] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001539] CPU: Testing write buffer coherency: ok [ 0.001578] CPU0: Spectre v2: using ICIALLU workaround [ 0.001778] /cpus/cpu@0 missing clock-frequency property [ 0.001793] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039856] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059862] Hierarchical SRCU implementation. [ 0.080044] EFI services will not be available. [ 0.099916] smp: Bringing up secondary CPUs ... [ 0.099927] smp: Brought up 1 node, 1 CPU [ 0.099936] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099944] CPU: All CPU(s) started in HYP mode. [ 0.099951] CPU: Virtualization extensions available. [ 0.100355] devtmpfs: initialized [ 0.118010] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120075] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120274] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120291] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124077] pinctrl core: initialized pinctrl subsystem [ 0.124580] DMI not present or invalid. [ 0.124823] NET: Registered protocol family 16 [ 0.130804] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131684] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.326818] cpuidle: using governor ladder [ 0.326852] cpuidle: using governor menu [ 0.335258] OMAP GPIO hardware version 0.1 [ 0.362535] No ATAGs? [ 0.362584] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.362598] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.362993] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.363004] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.363553] OMAP DMA hardware revision 0.0 [ 0.402432] edma 43300000.edma: memcpy is disabled [ 0.405609] edma 43300000.edma: TI EDMA DMA engine driver [ 0.412426] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.415916] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.416128] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.416369] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.416612] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.416953] iommu: Adding device 58820000.ipu to group 1 [ 0.417036] iommu: Adding device 55020000.ipu to group 2 [ 0.417190] iommu: Adding device 40800000.dsp to group 0 [ 0.419893] palmas 0-0058: Irq flag is 0x00000004 [ 0.442196] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.443787] SMPS12: supplied by regulator-dummy [ 0.445497] SMPS3: supplied by VMAIN [ 0.447045] SMPS45: supplied by regulator-dummy [ 0.448850] SMPS6: supplied by VMAIN [ 0.450530] SMPS7: supplied by VMAIN [ 0.451939] SMPS8: supplied by VMAIN [ 0.453175] SMPS9: supplied by VMAIN [ 0.454164] LDO1: supplied by VMAIN [ 0.461271] LDO2: supplied by VMAIN [ 0.470558] random: fast init done [ 0.471153] LDO3: supplied by VMAIN [ 0.481163] LDO4: supplied by VMAIN [ 0.491161] LDO5: supplied by regulator-dummy [ 0.491857] LDO6: supplied by regulator-dummy [ 0.492552] LDO7: supplied by regulator-dummy [ 0.493245] LDO8: supplied by regulator-dummy [ 0.493958] LDO9: supplied by VMAIN [ 0.501502] LDOLN: supplied by VMAIN [ 0.511217] LDOUSB: supplied by VMAIN [ 0.524265] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.524545] pps_core: LinuxPPS API ver. 1 registered [ 0.524555] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.524575] PTP clock support registered [ 0.524603] EDAC MC: Ver: 3.0.0 [ 0.530703] dmi: Firmware registration failed. [ 0.531149] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.531362] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.532287] clocksource: Switched to clocksource arch_sys_counter [ 0.539751] NET: Registered protocol family 2 [ 0.540290] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.540329] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.540397] TCP: Hash tables configured (established 4096 bind 4096) [ 0.540454] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.540476] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.540584] NET: Registered protocol family 1 [ 0.560990] RPC: Registered named UNIX socket transport module. [ 0.561001] RPC: Registered udp transport module. [ 0.561009] RPC: Registered tcp transport module. [ 0.561017] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.561965] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.562094] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.563165] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.567306] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.577851] NFS: Registering the id_resolver key type [ 0.577874] Key type id_resolver registered [ 0.577882] Key type id_legacy registered [ 0.577919] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.579581] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.579594] io scheduler noop registered [ 0.579604] io scheduler deadline registered [ 0.579700] io scheduler cfq registered (default) [ 0.579710] io scheduler mq-deadline registered [ 0.579718] io scheduler kyber registered [ 0.584422] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.584575] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.584649] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.584660] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.597992] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 0.598378] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 0.598415] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 0.598440] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 1.598691] dra7-pcie 51000000.pcie: phy link never came up [ 1.598824] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 1.598838] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.598849] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.598860] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 1.599173] PCI: bus0: Fast back to back transfers disabled [ 1.599264] PCI: bus1: Fast back to back transfers enabled [ 1.599303] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 1.599322] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.599646] pcieport 0000:00:00.0: Signaling PME with IRQ 170 [ 1.599770] pcieport 0000:00:00.0: AER enabled with IRQ 170 [ 1.600799] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.603393] V3_3D: supplied by smps9 [ 1.603657] vtt_fixed: supplied by V3_3D [ 1.645312] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 1.648049] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 45, base_baud = 3000000) is a 8250 [ 2.682570] console [ttyS0] enabled [ 2.688044] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 2.695175] DSS: OMAP DSS rev 6.1 [ 2.700247] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.708738] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.719521] panel-dpi display: display supply vcc not found, using dummy regulator [ 2.737360] brd: module loaded [ 2.745961] loop: module loaded [ 2.753231] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 2.760002] libphy: Fixed MDIO Bus: probed [ 2.765431] i2c /dev entries driver [ 2.774878] sdhci: Secure Digital Host Controller Interface driver [ 2.781219] sdhci: Copyright(c) Pierre Ossman [ 2.786712] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.792847] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.798257] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 2.804949] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode [ 2.872732] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.919768] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.929940] mmc0: new high speed SDHC card at address 59b4 [ 2.935838] mmcblk0: mmc0:59b4 00000 14.9 GiB [ 2.941867] mmcblk0: p1 p2 [ 2.944706] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.946027] ledtrig-cpu: registered to indicate activity on CPUs [ 2.955413] NET: Registered protocol family 10 [ 2.966494] Segment Routing with IPv6 [ 2.966541] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.966933] NET: Registered protocol family 17 [ 2.967116] Key type dns_resolver registered [ 2.967227] omap_voltage_late_init: Voltage driver support not added [ 2.967230] Power Management for TI OMAP4+ devices. [ 2.967446] Registering SWP/SWPB emulation handler [ 3.015463] dmm 4e000000.dmm: workaround for errata i878 in use [ 3.121329] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.142294] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003 [ 3.151378] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.172290] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000 [ 3.181287] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=1 F=11)0x2902b [ 3.212290] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=0)0x29000 [ 3.221286] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.252290] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000 [ 3.261286] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.282291] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.291201] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=4)0x29004 [ 3.322289] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=5)0x29005 [ 3.331374] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002 [ 3.362290] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000 [ 3.371199] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=7)0x29007 [ 3.392289] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.401199] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.432290] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001 [ 3.441286] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.462289] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.471199] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.502289] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.511199] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.532289] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.541198] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.572289] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.581199] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.612290] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.621199] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 3.647512] mmc1: new DDR MMC card at address 0001 [ 3.662544] mmcblk1: mmc1:0001 DG4032 29.1 GiB [ 3.667207] mmcblk1boot0: mmc1:0001 DG4032 partition 1 4.00 MiB [ 3.682406] mmcblk1boot1: mmc1:0001 DG4032 partition 2 4.00 MiB [ 3.688459] mmcblk1rpmb: mmc1:0001 DG4032 partition 3 4.00 MiB �