U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000345] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000354] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000806] Console: colour dummy device 80x30
[    0.000824] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000831] This ensures that you still see kernel messages. Please
[    0.000838] update your kernel commandline.
[    0.000857] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000872] pid_max: default: 32768 minimum: 301
[    0.000990] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001002] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001530] CPU: Testing write buffer coherency: ok
[    0.001569] CPU0: Spectre v2: using ICIALLU workaround
[    0.001772] /cpus/cpu@0 missing clock-frequency property
[    0.001786] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039857] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059863] Hierarchical SRCU implementation.
[    0.080049] EFI services will not be available.
[    0.099921] smp: Bringing up secondary CPUs ...
[    0.099932] smp: Brought up 1 node, 1 CPU
[    0.099941] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099949] CPU: All CPU(s) started in HYP mode.
[    0.099956] CPU: Virtualization extensions available.
[    0.100363] devtmpfs: initialized
[    0.118125] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120066] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120264] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120281] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124080] pinctrl core: initialized pinctrl subsystem
[    0.124588] DMI not present or invalid.
[    0.124825] NET: Registered protocol family 16
[    0.130811] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131678] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326919] cpuidle: using governor ladder
[    0.326953] cpuidle: using governor menu
[    0.334858] OMAP GPIO hardware version 0.1
[    0.357921] No ATAGs?
[    0.357970] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357984] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.358394] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.358405] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358943] OMAP DMA hardware revision 0.0
[    0.392310] edma 43300000.edma: memcpy is disabled
[    0.395473] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402247] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405579] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405780] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.406026] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406274] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406571] iommu: Adding device 58820000.ipu to group 1
[    0.406660] iommu: Adding device 55020000.ipu to group 2
[    0.406810] iommu: Adding device 40800000.dsp to group 0
[    0.409118] palmas 0-0058: Irq flag is 0x00000004
[    0.432813] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.434414] SMPS12: supplied by regulator-dummy
[    0.436149] SMPS3: supplied by VMAIN
[    0.437695] SMPS45: supplied by regulator-dummy
[    0.439524] SMPS6: supplied by VMAIN
[    0.441207] SMPS7: supplied by VMAIN
[    0.442620] SMPS8: supplied by VMAIN
[    0.443867] SMPS9: supplied by VMAIN
[    0.444857] LDO1: supplied by VMAIN
[    0.450634] random: fast init done
[    0.451288] LDO2: supplied by VMAIN
[    0.461156] LDO3: supplied by VMAIN
[    0.471174] LDO4: supplied by VMAIN
[    0.481160] LDO5: supplied by regulator-dummy
[    0.481858] LDO6: supplied by regulator-dummy
[    0.482555] LDO7: supplied by regulator-dummy
[    0.483250] LDO8: supplied by regulator-dummy
[    0.483956] LDO9: supplied by VMAIN
[    0.491503] LDOLN: supplied by VMAIN
[    0.501211] LDOUSB: supplied by VMAIN
[    0.514247] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514485] pps_core: LinuxPPS API ver. 1 registered
[    0.514494] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514514] PTP clock support registered
[    0.514541] EDAC MC: Ver: 3.0.0
[    0.520699] dmi: Firmware registration failed.
[    0.521138] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521341] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522224] clocksource: Switched to clocksource arch_sys_counter
[    0.529662] NET: Registered protocol family 2
[    0.530194] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530233] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530301] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530359] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530382] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530493] NET: Registered protocol family 1
[    0.550901] RPC: Registered named UNIX socket transport module.
[    0.550911] RPC: Registered udp transport module.
[    0.550919] RPC: Registered tcp transport module.
[    0.550927] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551810] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551939] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.552986] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557117] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567671] NFS: Registering the id_resolver key type
[    0.567695] Key type id_resolver registered
[    0.567704] Key type id_legacy registered
[    0.567742] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569374] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569386] io scheduler noop registered
[    0.569395] io scheduler deadline registered
[    0.569490] io scheduler cfq registered (default)
[    0.569500] io scheduler mq-deadline registered
[    0.569509] io scheduler kyber registered
[    0.573664] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573815] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573890] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573902] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587627] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589943] V3_3D: supplied by smps9
[    0.590209] vtt_fixed: supplied by V3_3D
[    0.632176] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634927] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578232] console [ttyS0] enabled
[    1.583552] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601472] brd: module loaded
[    1.610031] loop: module loaded
[    1.616034] libphy: Fixed MDIO Bus: probed
[    1.621373] i2c /dev entries driver
[    1.630775] sdhci: Secure Digital Host Controller Interface driver
[    1.637145] sdhci: Copyright(c) Pierre Ossman
[    1.642595] sdhci-pltfm: SDHCI platform and OF��
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000349] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000358] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000810] Console: colour dummy device 80x30
[    0.000828] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000836] This ensures that you still see kernel messages. Please
[    0.000843] update your kernel commandline.
[    0.000861] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000876] pid_max: default: 32768 minimum: 301
[    0.000995] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001006] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001535] CPU: Testing write buffer coherency: ok
[    0.001575] CPU0: Spectre v2: using ICIALLU workaround
[    0.001778] /cpus/cpu@0 missing clock-frequency property
[    0.001792] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039854] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059858] Hierarchical SRCU implementation.
[    0.080044] EFI services will not be available.
[    0.099917] smp: Bringing up secondary CPUs ...
[    0.099928] smp: Brought up 1 node, 1 CPU
[    0.099937] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099945] CPU: All CPU(s) started in HYP mode.
[    0.099952] CPU: Virtualization extensions available.
[    0.100362] devtmpfs: initialized
[    0.118026] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120060] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120258] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120277] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124069] pinctrl core: initialized pinctrl subsystem
[    0.124575] DMI not present or invalid.
[    0.124816] NET: Registered protocol family 16
[    0.130807] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131677] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326148] cpuidle: using governor ladder
[    0.326183] cpuidle: using governor menu
[    0.334108] OMAP GPIO hardware version 0.1
[    0.357126] No ATAGs?
[    0.357174] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357188] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.357573] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.357584] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358123] OMAP DMA hardware revision 0.0
[    0.392317] edma 43300000.edma: memcpy is disabled
[    0.395492] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402301] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405630] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405830] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.406074] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406326] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406621] iommu: Adding device 58820000.ipu to group 1
[    0.406711] iommu: Adding device 55020000.ipu to group 2
[    0.406861] iommu: Adding device 40800000.dsp to group 0
[    0.409036] palmas 0-0058: Irq flag is 0x00000004
[    0.432184] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433783] SMPS12: supplied by regulator-dummy
[    0.435496] SMPS3: supplied by VMAIN
[    0.437051] SMPS45: supplied by regulator-dummy
[    0.438860] SMPS6: supplied by VMAIN
[    0.440531] SMPS7: supplied by VMAIN
[    0.441942] SMPS8: supplied by VMAIN
[    0.443195] SMPS9: supplied by VMAIN
[    0.444179] LDO1: supplied by VMAIN
[    0.451282] LDO2: supplied by VMAIN
[    0.451615] random: fast init done
[    0.461151] LDO3: supplied by VMAIN
[    0.471162] LDO4: supplied by VMAIN
[    0.481156] LDO5: supplied by regulator-dummy
[    0.481867] LDO6: supplied by regulator-dummy
[    0.482567] LDO7: supplied by regulator-dummy
[    0.483266] LDO8: supplied by regulator-dummy
[    0.483978] LDO9: supplied by VMAIN
[    0.491500] LDOLN: supplied by VMAIN
[    0.501208] LDOUSB: supplied by VMAIN
[    0.514255] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514487] pps_core: LinuxPPS API ver. 1 registered
[    0.514496] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514516] PTP clock support registered
[    0.514544] EDAC MC: Ver: 3.0.0
[    0.520697] dmi: Firmware registration failed.
[    0.521128] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521327] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522218] clocksource: Switched to clocksource arch_sys_counter
[    0.529697] NET: Registered protocol family 2
[    0.530241] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530279] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530347] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530404] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530426] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530536] NET: Registered protocol family 1
[    0.550935] RPC: Registered named UNIX socket transport module.
[    0.550946] RPC: Registered udp transport module.
[    0.550953] RPC: Registered tcp transport module.
[    0.550961] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551837] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551965] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.553008] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557126] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567683] NFS: Registering the id_resolver key type
[    0.567706] Key type id_resolver registered
[    0.567715] Key type id_legacy registered
[    0.567753] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569385] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569398] io scheduler noop registered
[    0.569407] io scheduler deadline registered
[    0.569505] io scheduler cfq registered (default)
[    0.569515] io scheduler mq-deadline registered
[    0.569524] io scheduler kyber registered
[    0.573634] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573787] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573861] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573872] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587613] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589935] V3_3D: supplied by smps9
[    0.590195] vtt_fixed: supplied by V3_3D
[    0.632001] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634734] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578050] console [ttyS0] enabled
[    1.583363] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601255] brd: module loaded
[    1.609839] loop: module loaded
[    1.615859] libphy: Fixed MDIO Bus: probed
[    1.621210] i2c /dev entries driver
[    1.630562] sdhci: Secure Digital Host Controller Interface driver
[    1.636929] sdhci: Copyright(c) Pierre Ossman
[    1.642373] sdhci-pltfm: SDHCI platform and OF driver helper
�
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000016] Switching to timer-based delay loop, resolution 162ns
[    0.000345] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000354] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000796] Console: colour dummy device 80x30
[    0.000814] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000821] This ensures that you still see kernel messages. Please
[    0.000828] update your kernel commandline.
[    0.000846] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000861] pid_max: default: 32768 minimum: 301
[    0.000977] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000988] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001518] CPU: Testing write buffer coherency: ok
[    0.001559] CPU0: Spectre v2: using ICIALLU workaround
[    0.001763] /cpus/cpu@0 missing clock-frequency property
[    0.001777] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039860] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059866] Hierarchical SRCU implementation.
[    0.080052] EFI services will not be available.
[    0.099926] smp: Bringing up secondary CPUs ...
[    0.099936] smp: Brought up 1 node, 1 CPU
[    0.099945] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099953] CPU: All CPU(s) started in HYP mode.
[    0.099960] CPU: Virtualization extensions available.
[    0.100370] devtmpfs: initialized
[    0.118036] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120071] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120267] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120284] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124078] pinctrl core: initialized pinctrl subsystem
[    0.124579] DMI not present or invalid.
[    0.124818] NET: Registered protocol family 16
[    0.130811] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131680] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326696] cpuidle: using governor ladder
[    0.326731] cpuidle: using governor menu
[    0.334647] OMAP GPIO hardware version 0.1
[    0.357667] No ATAGs?
[    0.357715] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357730] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.358113] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.358124] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358662] OMAP DMA hardware revision 0.0
[    0.392301] edma 43300000.edma: memcpy is disabled
[    0.395456] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402253] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405582] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405782] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.406026] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406272] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406564] iommu: Adding device 58820000.ipu to group 1
[    0.406653] iommu: Adding device 55020000.ipu to group 2
[    0.406805] iommu: Adding device 40800000.dsp to group 0
[    0.408983] palmas 0-0058: Irq flag is 0x00000004
[    0.432185] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433788] SMPS12: supplied by regulator-dummy
[    0.435495] SMPS3: supplied by VMAIN
[    0.437051] SMPS45: supplied by regulator-dummy
[    0.438865] SMPS6: supplied by VMAIN
[    0.440527] SMPS7: supplied by VMAIN
[    0.441944] SMPS8: supplied by VMAIN
[    0.443199] SMPS9: supplied by VMAIN
[    0.444187] LDO1: supplied by VMAIN
[    0.451264] LDO2: supplied by VMAIN
[    0.451468] random: fast init done
[    0.461152] LDO3: supplied by VMAIN
[    0.471156] LDO4: supplied by VMAIN
[    0.481147] LDO5: supplied by regulator-dummy
[    0.481845] LDO6: supplied by regulator-dummy
[    0.482548] LDO7: supplied by regulator-dummy
[    0.483243] LDO8: supplied by regulator-dummy
[    0.483959] LDO9: supplied by VMAIN
[    0.491496] LDOLN: supplied by VMAIN
[    0.501198] LDOUSB: supplied by VMAIN
[    0.514241] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514474] pps_core: LinuxPPS API ver. 1 registered
[    0.514483] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514503] PTP clock support registered
[    0.514531] EDAC MC: Ver: 3.0.0
[    0.520689] dmi: Firmware registration failed.
[    0.521125] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521325] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522215] clocksource: Switched to clocksource arch_sys_counter
[    0.529691] NET: Registered protocol family 2
[    0.530234] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530273] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530340] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530397] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530419] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530528] NET: Registered protocol family 1
[    0.550928] RPC: Registered named UNIX socket transport module.
[    0.550938] RPC: Registered udp transport module.
[    0.550946] RPC: Registered tcp transport module.
[    0.550954] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551832] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551959] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.553010] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557133] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567689] NFS: Registering the id_resolver key type
[    0.567712] Key type id_resolver registered
[    0.567721] Key type id_legacy registered
[    0.567759] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569392] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569404] io scheduler noop registered
[    0.569413] io scheduler deadline registered
[    0.569509] io scheduler cfq registered (default)
[    0.569519] io scheduler mq-deadline registered
[    0.569528] io scheduler kyber registered
[    0.573628] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573781] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573856] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573867] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587566] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589880] V3_3D: supplied by smps9
[    0.590140] vtt_fixed: supplied by V3_3D
[    0.632032] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634767] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578069] console [ttyS0] enabled
[    1.583382] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601290] brd: module loaded
[    1.609856] loop: module loaded
[    1.615857] libphy: Fixed MDIO Bus: probed
[    1.621205] i2c /dev entries driver
[    1.630576] sdhci: Secure Digital Host Controller Interface driver
[    1.636945] sdhci: Copyright(c) Pierre Ossman
[    1.642370] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.648493] sdhci-omap 4809c000.mmc: Got CD GPIO
[    1.653955] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[    1.660599] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[    1.722430] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[    1.730937] ledtrig-cpu: registered to indicate activity on CPUs
[    1.742921] NET: Registered protocol family 10
[    1.748054] Segment Routing with IPv6
[    1.751885] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[  ��
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000346] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000355] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000801] Console: colour dummy device 80x30
[    0.000819] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000827] This ensures that you still see kernel messages. Please
[    0.000834] update your kernel commandline.
[    0.000852] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000867] pid_max: default: 32768 minimum: 301
[    0.000986] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000997] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001525] CPU: Testing write buffer coherency: ok
[    0.001565] CPU0: Spectre v2: using ICIALLU workaround
[    0.001769] /cpus/cpu@0 missing clock-frequency property
[    0.001782] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039858] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059864] Hierarchical SRCU implementation.
[    0.080052] EFI services will not be available.
[    0.099924] smp: Bringing up secondary CPUs ...
[    0.099935] smp: Brought up 1 node, 1 CPU
[    0.099944] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099952] CPU: All CPU(s) started in HYP mode.
[    0.099959] CPU: Virtualization extensions available.
[    0.100367] devtmpfs: initialized
[    0.118017] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120071] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120268] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120285] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124042] pinctrl core: initialized pinctrl subsystem
[    0.124540] DMI not present or invalid.
[    0.124783] NET: Registered protocol family 16
[    0.130810] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131679] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326574] cpuidle: using governor ladder
[    0.326609] cpuidle: using governor menu
[    0.334521] OMAP GPIO hardware version 0.1
[    0.357515] No ATAGs?
[    0.357562] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357577] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.357967] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.357977] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358515] OMAP DMA hardware revision 0.0
[    0.392309] edma 43300000.edma: memcpy is disabled
[    0.395492] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402243] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405548] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405748] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.405991] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406239] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406534] iommu: Adding device 58820000.ipu to group 1
[    0.406624] iommu: Adding device 55020000.ipu to group 2
[    0.406773] iommu: Adding device 40800000.dsp to group 0
[    0.409072] palmas 0-0058: Irq flag is 0x00000004
[    0.432193] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433778] SMPS12: supplied by regulator-dummy
[    0.435490] SMPS3: supplied by VMAIN
[    0.437031] SMPS45: supplied by regulator-dummy
[    0.438849] SMPS6: supplied by VMAIN
[    0.440525] SMPS7: supplied by VMAIN
[    0.441950] SMPS8: supplied by VMAIN
[    0.443194] SMPS9: supplied by VMAIN
[    0.444180] LDO1: supplied by VMAIN
[    0.451269] LDO2: supplied by VMAIN
[    0.451522] random: fast init done
[    0.461158] LDO3: supplied by VMAIN
[    0.471166] LDO4: supplied by VMAIN
[    0.481155] LDO5: supplied by regulator-dummy
[    0.481862] LDO6: supplied by regulator-dummy
[    0.482562] LDO7: supplied by regulator-dummy
[    0.483263] LDO8: supplied by regulator-dummy
[    0.483970] LDO9: supplied by VMAIN
[    0.491503] LDOLN: supplied by VMAIN
[    0.501210] LDOUSB: supplied by VMAIN
[    0.514250] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514484] pps_core: LinuxPPS API ver. 1 registered
[    0.514494] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514513] PTP clock support registered
[    0.514541] EDAC MC: Ver: 3.0.0
[    0.520698] dmi: Firmware registration failed.
[    0.521137] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521339] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522235] clocksource: Switched to clocksource arch_sys_counter
[    0.529699] NET: Registered protocol family 2
[    0.530240] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530279] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530347] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530404] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530426] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530536] NET: Registered protocol family 1
[    0.550938] RPC: Registered named UNIX socket transport module.
[    0.550949] RPC: Registered udp transport module.
[    0.550956] RPC: Registered tcp transport module.
[    0.550964] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551838] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551967] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.553022] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557138] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567690] NFS: Registering the id_resolver key type
[    0.567717] Key type id_resolver registered
[    0.567726] Key type id_legacy registered
[    0.567763] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569402] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569414] io scheduler noop registered
[    0.569423] io scheduler deadline registered
[    0.569521] io scheduler cfq registered (default)
[    0.569531] io scheduler mq-deadline registered
[    0.569540] io scheduler kyber registered
[    0.573696] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573847] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573920] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573932] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587643] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589965] V3_3D: supplied by smps9
[    0.590224] vtt_fixed: supplied by V3_3D
[    0.631972] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634718] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578017] console [ttyS0] enabled
[    1.583322] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601271] brd: module loaded
[    1.609847] loop: module loaded
[    1.615854] libphy: Fixed MDIO Bus: probed
[    1.621189] i2c /dev entries driver
[    1.630565] sdhci: Secure Digital Host Controller Interface driver
[    1.636934] sdhci: Copyright(c) Pierre Ossman
[    1.642381] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.648504] sdhci-omap 4809c000.mmc: Got CD GPIO
[    1.653975] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[    1.660618] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[    1.722450] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[    1.730949] ledtrig-cpu: registered to indicate activity on CPUs
[    1.742929] NET: Registered protocol family 10
[    1.748060] Segment Routing with IPv6
[    1.751894] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.759459] NET: Registered protocol family 17
[    1.767182] Key type dns_resolver registered
[�
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000349] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000358] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000801] Console: colour dummy device 80x30
[    0.000819] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000826] This ensures that you still see kernel messages. Please
[    0.000833] update your kernel commandline.
[    0.000851] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000866] pid_max: default: 32768 minimum: 301
[    0.000985] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001524] CPU: Testing write buffer coherency: ok
[    0.001563] CPU0: Spectre v2: using ICIALLU workaround
[    0.001765] /cpus/cpu@0 missing clock-frequency property
[    0.001778] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039857] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059861] Hierarchical SRCU implementation.
[    0.080047] EFI services will not be available.
[    0.099920] smp: Bringing up secondary CPUs ...
[    0.099931] smp: Brought up 1 node, 1 CPU
[    0.099940] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099948] CPU: All CPU(s) started in HYP mode.
[    0.099955] CPU: Virtualization extensions available.
[    0.100360] devtmpfs: initialized
[    0.118060] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120062] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120258] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120276] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124046] pinctrl core: initialized pinctrl subsystem
[    0.124548] DMI not present or invalid.
[    0.124788] NET: Registered protocol family 16
[    0.130802] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131685] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326839] cpuidle: using governor ladder
[    0.326875] cpuidle: using governor menu
[    0.334771] OMAP GPIO hardware version 0.1
[    0.357813] No ATAGs?
[    0.357862] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357876] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.358259] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.358271] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358808] OMAP DMA hardware revision 0.0
[    0.392313] edma 43300000.edma: memcpy is disabled
[    0.395458] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402233] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405547] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405748] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.405993] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406242] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406534] iommu: Adding device 58820000.ipu to group 1
[    0.406624] iommu: Adding device 55020000.ipu to group 2
[    0.406773] iommu: Adding device 40800000.dsp to group 0
[    0.408957] palmas 0-0058: Irq flag is 0x00000004
[    0.432175] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433767] SMPS12: supplied by regulator-dummy
[    0.435480] SMPS3: supplied by VMAIN
[    0.437023] SMPS45: supplied by regulator-dummy
[    0.438837] SMPS6: supplied by VMAIN
[    0.440512] SMPS7: supplied by VMAIN
[    0.441926] SMPS8: supplied by VMAIN
[    0.443165] SMPS9: supplied by VMAIN
[    0.444144] LDO1: supplied by VMAIN
[    0.451269] LDO2: supplied by VMAIN
[    0.451602] random: fast init done
[    0.461147] LDO3: supplied by VMAIN
[    0.471159] LDO4: supplied by VMAIN
[    0.481155] LDO5: supplied by regulator-dummy
[    0.481850] LDO6: supplied by regulator-dummy
[    0.482549] LDO7: supplied by regulator-dummy
[    0.483255] LDO8: supplied by regulator-dummy
[    0.483969] LDO9: supplied by VMAIN
[    0.491508] LDOLN: supplied by VMAIN
[    0.501201] LDOUSB: supplied by VMAIN
[    0.514246] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514479] pps_core: LinuxPPS API ver. 1 registered
[    0.514488] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514508] PTP clock support registered
[    0.514536] EDAC MC: Ver: 3.0.0
[    0.520691] dmi: Firmware registration failed.
[    0.521126] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521328] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522218] clocksource: Switched to clocksource arch_sys_counter
[    0.529671] NET: Registered protocol family 2
[    0.530215] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530254] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530321] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530378] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530401] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530510] NET: Registered protocol family 1
[    0.550911] RPC: Registered named UNIX socket transport module.
[    0.550921] RPC: Registered udp transport module.
[    0.550929] RPC: Registered tcp transport module.
[    0.550937] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551813] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551944] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.552994] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557117] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567665] NFS: Registering the id_resolver key type
[    0.567700] Key type id_resolver registered
[    0.567708] Key type id_legacy registered
[    0.567745] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569376] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569389] io scheduler noop registered
[    0.569397] io scheduler deadline registered
[    0.569493] io scheduler cfq registered (default)
[    0.569503] io scheduler mq-deadline registered
[    0.569512] io scheduler kyber registered
[    0.573676] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573826] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573899] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573911] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587623] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589907] V3_3D: supplied by smps9
[    0.590167] vtt_fixed: supplied by V3_3D
[    0.631665] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634412] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.577737] console [ttyS0] enabled
[    1.583047] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.600981] brd: module loaded
[    1.609558] loop: module loaded
[    1.615561] libphy: Fixed MDIO Bus: probed
[    1.620912] i2c /dev entries driver
[    1.630284] sdhci: Secure Digital Host Controller Interface driver
[    1.636655] sdhci: Copyright(c) Pierre Ossman
[    1.642073] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.648208] sdhci-omap 4809c000.mmc: Got CD GPIO
[    1.653673] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[    1.660317] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[    1.722431] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[    1.730937] ledtrig-cpu: registered to indicate activity on CPUs
[    1.742919] NET: Registered protocol family 10
[    1.748051] Segment Routing with IPv6
[    1.751881] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.759460] NET: Registered protocol family 17
[    1.767186] Key type dns_resolver registered
[    1.771586] omap_voltage_late_init: Voltage driver support not added
[    1.778023] Power Management for TI OMAP4+ devices.
[    1.783138] Registering SWP/SWPB emulation handler
[    1.796869] dmm 4e000000.dmm: workaround for errata i878 in use
[    1.819602] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.844306] mmc0: new high speed SDHC card at address 59b4
[    1.862246] mmcblk0: mmc0:59b4 00000 14.9 GiB 
[    1.867791]  mmcblk0: p1 p2
[    2.823136] dmm 4e000000.dmm: After delay 1000ms
[    2.827791] dmm 4e000000.dmm: After hwinfo
[    3.832144] dmm 4e000000.dmm: Before dmm_write
[    3.836677] dmm 4e000000.dmm: After dmm_write
[    4.842138] dmm 4e000000.dmm: Test 1
[    4.845790] dmm 4e000000.dmm: Test 2
[    4.849378] dmm 4e000000.dmm: Test 3
[    4.852976] dmm 4e000000.dmm: Test 5
[    4.856562] (NULL device *): After dmm_txn_init
[    4.861107] (NULL device *): After tcm_for_each_slice
��
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000345] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000354] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000804] Console: colour dummy device 80x30
[    0.000821] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000829] This ensures that you still see kernel messages. Please
[    0.000836] update your kernel commandline.
[    0.000853] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000868] pid_max: default: 32768 minimum: 301
[    0.000988] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000999] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001529] CPU: Testing write buffer coherency: ok
[    0.001568] CPU0: Spectre v2: using ICIALLU workaround
[    0.001769] /cpus/cpu@0 missing clock-frequency property
[    0.001783] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039856] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059863] Hierarchical SRCU implementation.
[    0.080048] EFI services will not be available.
[    0.099922] smp: Bringing up secondary CPUs ...
[    0.099932] smp: Brought up 1 node, 1 CPU
[    0.099941] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099949] CPU: All CPU(s) started in HYP mode.
[    0.099956] CPU: Virtualization extensions available.
[    0.100365] devtmpfs: initialized
[    0.118051] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120065] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120262] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120280] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124107] pinctrl core: initialized pinctrl subsystem
[    0.124609] DMI not present or invalid.
[    0.124851] NET: Registered protocol family 16
[    0.130809] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131679] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.326599] cpuidle: using governor ladder
[    0.326633] cpuidle: using governor menu
[    0.334531] OMAP GPIO hardware version 0.1
[    0.357534] No ATAGs?
[    0.357584] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357599] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.357990] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.358002] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.358543] OMAP DMA hardware revision 0.0
[    0.392307] edma 43300000.edma: memcpy is disabled
[    0.395493] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402327] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405623] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405823] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.406070] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406319] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406617] iommu: Adding device 58820000.ipu to group 1
[    0.406706] iommu: Adding device 55020000.ipu to group 2
[    0.406857] iommu: Adding device 40800000.dsp to group 0
[    0.409174] palmas 0-0058: Irq flag is 0x00000004
[    0.432194] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433791] SMPS12: supplied by regulator-dummy
[    0.435501] SMPS3: supplied by VMAIN
[    0.437043] SMPS45: supplied by regulator-dummy
[    0.438851] SMPS6: supplied by VMAIN
[    0.440531] SMPS7: supplied by VMAIN
[    0.441972] SMPS8: supplied by VMAIN
[    0.443208] SMPS9: supplied by VMAIN
[    0.444185] LDO1: supplied by VMAIN
[    0.451270] LDO2: supplied by VMAIN
[    0.451594] random: fast init done
[    0.461150] LDO3: supplied by VMAIN
[    0.471161] LDO4: supplied by VMAIN
[    0.481154] LDO5: supplied by regulator-dummy
[    0.481848] LDO6: supplied by regulator-dummy
[    0.482536] LDO7: supplied by regulator-dummy
[    0.483232] LDO8: supplied by regulator-dummy
[    0.483946] LDO9: supplied by VMAIN
[    0.491493] LDOLN: supplied by VMAIN
[    0.501212] LDOUSB: supplied by VMAIN
[    0.514248] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514484] pps_core: LinuxPPS API ver. 1 registered
[    0.514494] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514513] PTP clock support registered
[    0.514542] EDAC MC: Ver: 3.0.0
[    0.520696] dmi: Firmware registration failed.
[    0.521132] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521334] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522223] clocksource: Switched to clocksource arch_sys_counter
[    0.529670] NET: Registered protocol family 2
[    0.530217] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530256] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530324] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530380] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530402] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530512] NET: Registered protocol family 1
[    0.550914] RPC: Registered named UNIX socket transport module.
[    0.550925] RPC: Registered udp transport module.
[    0.550933] RPC: Registered tcp transport module.
[    0.550941] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551815] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551942] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.552995] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557115] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567669] NFS: Registering the id_resolver key type
[    0.567697] Key type id_resolver registered
[    0.567706] Key type id_legacy registered
[    0.567743] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569382] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569395] io scheduler noop registered
[    0.569404] io scheduler deadline registered
[    0.569501] io scheduler cfq registered (default)
[    0.569511] io scheduler mq-deadline registered
[    0.569519] io scheduler kyber registered
[    0.573662] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573815] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573889] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573901] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587604] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589900] V3_3D: supplied by smps9
[    0.590160] vtt_fixed: supplied by V3_3D
[    0.632187] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634932] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578248] console [ttyS0] enabled
[    1.583560] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601519] brd: module loaded
[    1.610074] loop: module loaded
[    1.616082] libphy: Fixed MDIO Bus: probed
[    1.621426] i2c /dev entries driver
[    1.630787] sdhci: Secure Digital Host Controller Interface driver
[    1.637155] sdhci: Copyright(c) Pierre Ossman
[    1.642595] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.648715] sdhci-omap 4809c000.mmc: Got CD GPIO
[    1.654183] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[    1.660826] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[    1.722439] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[    1.730939] ledtrig-cpu: registered to indicate activity on CPUs
[    1.742931] NET: Registered protocol family 10
[    1.748064] Segment Routing with IPv6
[    1.751894] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.759445] NET: Registered protocol family 17
[    1.767166] Key type dns_resolver registered
[��
U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28)
DRA722-GP ES2.0
SPL: 355 Trying to boot from MMC1
no pinctrl state for default mode
no pinctrl state for default mode


U-Boot 2018.01-00569-gfd38f5a-dirty (May 29 2019 - 16:15:28 +0530)

CPU  : DRA722-GP ES2.0
Model: TI AM5718 IDK
Board: AM571x IDK REV 1.3B
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
__led_init: failed requesting GPIO1!
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
SCSI:  SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst 
scanning bus for devices...
Found 0 device(s).
Net:   Could not get PHY for ethernet@48484000: addr 0
eth0: ethernet@48484000
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
1490 bytes read in 4 ms (363.3 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
3785216 bytes read in 188 ms (19.2 MiB/s)
97394 bytes read in 19 ms (4.9 MiB/s)
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffe5000, end 8ffffc71 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #15 SMP PREEM9
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB
[    0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 24 MiB at 0x0000000094000000
[    0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier
[    0.000000] DRA722 ES2.0
[    0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129158
[    0.000000] Kernel command line: console=ttyO0,115200n8 nomodule root=PARTUUID=e6a55ee4-02 rw rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 320176K/521216K available (8192K kernel code, 297K rwdata, 2368K rodata, 2048K init, 279K bss, 20816K reserved, 180224K)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0e00000 - 0xc1000000   (2048 kB)
[    0.000000]       .data : 0xc1000000 - 0xc104a618   ( 298 kB)
[    0.000000]        .bss : 0xc104c000 - 0xc1091c60   ( 280 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32786 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[    0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[    0.000017] Switching to timer-based delay loop, resolution 162ns
[    0.000348] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000357] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000804] Console: colour dummy device 80x30
[    0.000820] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[    0.000828] This ensures that you still see kernel messages. Please
[    0.000835] update your kernel commandline.
[    0.000853] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[    0.000868] pid_max: default: 32768 minimum: 301
[    0.000985] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001528] CPU: Testing write buffer coherency: ok
[    0.001568] CPU0: Spectre v2: using ICIALLU workaround
[    0.001773] /cpus/cpu@0 missing clock-frequency property
[    0.001787] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.039855] Setting up static identity map for 0x80200000 - 0x80200060
[    0.059862] Hierarchical SRCU implementation.
[    0.080047] EFI services will not be available.
[    0.099917] smp: Bringing up secondary CPUs ...
[    0.099928] smp: Brought up 1 node, 1 CPU
[    0.099937] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[    0.099945] CPU: All CPU(s) started in HYP mode.
[    0.099951] CPU: Virtualization extensions available.
[    0.100356] devtmpfs: initialized
[    0.118030] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[    0.120065] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.120260] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.120277] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.124063] pinctrl core: initialized pinctrl subsystem
[    0.124574] DMI not present or invalid.
[    0.124816] NET: Registered protocol family 16
[    0.130812] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.131681] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.325660] cpuidle: using governor ladder
[    0.325695] cpuidle: using governor menu
[    0.333592] OMAP GPIO hardware version 0.1
[    0.356592] No ATAGs?
[    0.356640] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.356655] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.357061] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.357072] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.357613] OMAP DMA hardware revision 0.0
[    0.392300] edma 43300000.edma: memcpy is disabled
[    0.395476] edma 43300000.edma: TI EDMA DMA engine driver
[    0.402336] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    0.405637] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[    0.405838] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[    0.406082] omap-iommu 58882000.mmu: 58882000.mmu registered
[    0.406331] omap-iommu 55082000.mmu: 55082000.mmu registered
[    0.406622] iommu: Adding device 58820000.ipu to group 1
[    0.406711] iommu: Adding device 55020000.ipu to group 2
[    0.406861] iommu: Adding device 40800000.dsp to group 0
[    0.409034] palmas 0-0058: Irq flag is 0x00000004
[    0.432204] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0
[    0.433801] SMPS12: supplied by regulator-dummy
[    0.435524] SMPS3: supplied by VMAIN
[    0.437075] SMPS45: supplied by regulator-dummy
[    0.438895] SMPS6: supplied by VMAIN
[    0.440562] SMPS7: supplied by VMAIN
[    0.441978] SMPS8: supplied by VMAIN
[    0.443222] SMPS9: supplied by VMAIN
[    0.444203] LDO1: supplied by VMAIN
[    0.451226] random: fast init done
[    0.451288] LDO2: supplied by VMAIN
[    0.461151] LDO3: supplied by VMAIN
[    0.471165] LDO4: supplied by VMAIN
[    0.481154] LDO5: supplied by regulator-dummy
[    0.481850] LDO6: supplied by regulator-dummy
[    0.482544] LDO7: supplied by regulator-dummy
[    0.483246] LDO8: supplied by regulator-dummy
[    0.483952] LDO9: supplied by VMAIN
[    0.491506] LDOLN: supplied by VMAIN
[    0.501213] LDOUSB: supplied by VMAIN
[    0.514271] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    0.514505] pps_core: LinuxPPS API ver. 1 registered
[    0.514514] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.514534] PTP clock support registered
[    0.514562] EDAC MC: Ver: 3.0.0
[    0.520695] dmi: Firmware registration failed.
[    0.521124] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[    0.521326] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[    0.522218] clocksource: Switched to clocksource arch_sys_counter
[    0.529680] NET: Registered protocol family 2
[    0.530226] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.530266] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.530334] TCP: Hash tables configured (established 4096 bind 4096)
[    0.530391] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.530414] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.530522] NET: Registered protocol family 1
[    0.550924] RPC: Registered named UNIX socket transport module.
[    0.550934] RPC: Registered udp transport module.
[    0.550942] RPC: Registered tcp transport module.
[    0.550949] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.551826] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.551955] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.553005] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.557117] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.567670] NFS: Registering the id_resolver key type
[    0.567692] Key type id_resolver registered
[    0.567701] Key type id_legacy registered
[    0.567738] ntfs: driver 2.1.32 [Flags: R/O].
[    0.569366] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.569378] io scheduler noop registered
[    0.569387] io scheduler deadline registered
[    0.569483] io scheduler cfq registered (default)
[    0.569494] io scheduler mq-deadline registered
[    0.569502] io scheduler kyber registered
[    0.573654] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[    0.573809] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[    0.573882] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[    0.573894] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[    0.587640] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.589958] V3_3D: supplied by smps9
[    0.590218] vtt_fixed: supplied by V3_3D
[    0.632060] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.634813] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250
[    1.578119] console [ttyS0] enabled
[    1.583415] omap_rng 48090000.rng: Random Number Generator ver. 20
[    1.601350] brd: module loaded
[    1.609912] loop: module loaded
[    1.615920] libphy: Fixed MDIO Bus: probed
[    1.621262] i2c /dev entries driver
[    1.630640] sdhci: Secure Digital Host Controller Interface driver
[    1.637007] sdhci: Copyright(c) Pierre Ossman
[    1.642435] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.648556] sdhci-omap 4809c000.mmc: Got CD GPIO
[    1.654016] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[    1.660660] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode
[    1.722429] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[    1.730923] ledtrig-cpu: registered to indicate activity on CPUs
[    1.742895] NET: Registered protocol family 10
[    1.748031] Segment Routing with IPv6
[    1.751863] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.759440] NET: Registered protocol family 17
[    1.767158] Key type dns_resolver registered
[    1.771560] omap_voltage_late_init: Voltage driver support not added
[    1.777999] Power Management for TI OMAP4+ devices.
[    1.783112] Registering SWP/SWPB emulation handler
[    1.796802] dmm 4e000000.dmm: workaround for errata i878 in use
[    1.819603] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.844305] mmc0: new high speed SDHC card at address 59b4
[    1.862243] mmcblk0: mmc0:59b4 00000 14.9 GiB 
[    1.867777]  mmcblk0: p1 p2
[    2.823136] dmm 4e000000.dmm: After delay 1000ms
[    2.827790] dmm 4e000000.dmm: After hwinfo
[    3.832135] dmm 4e000000.dmm: Before dmm_write
[    3.836655] dmm 4e000000.dmm: After dmm_write
[    4.842138] dmm 4e000000.dmm: Test 1
[    4.845778] dmm 4e000000.dmm: Test 2
[    4.849365] dmm 4e000000.dmm: Test 3
[    4.852975] dmm 4e000000.dmm: Test 5
[    4.856562] (NULL device *): After dmm_txn_init
[    4.861107] (NULL device *): After tcm_for_each_slice
��

