U-Boot SPL 2013.10-g756a473-dirty (Sep 24 2024 - 11:23:59) calixto > DDR initialized calixto > after sd ram init funUsing default environment usb_ether using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready musb-hdrc: peripheral reset irq lost! high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 Using usb_ether device TFTP from server 192.168.2.1; our IP address is 192.168.2.9 Filename 'u-boot-restore.img'. Load address: 0x807fffc0 Loading: ########################## 789.1 KiB/s done Bytes transferred = 367244 (59a8c hex) U-Boot 2013.10-g756a473-dirty (Sep 24 2024 - 11:23:59) I2C: ready DRAM: 256 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1, OMAP SD/MMC: 2 SF: Detected at25sf641 with page size 256 Bytes, erase size 4 KiB, total 8 MiB *** Warning - bad CRC, using default environment Net: not set. Validating first E-fuse MAC Could not get PHY for cpsw: addr 0 cpsw, usb_ether Hit any key to stop autoboot: 0 Booting for flashing ... using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready musb-hdrc: peripheral reset irq lost! high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.2.9 SF: Detected at25sf641 with page size 256 Bytes, erase size 4 KiB, total 8 MiB SF: 786432 bytes @ 0x0 Erased: OK using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! Using usb_ether device TFTP from server 192.168.2.1; our IP address is 192.168.2.9 Filename 'MLO.byteswap'. Load address: 0x80200000 Loading: T ######## 20.5 KiB/s done Bytes transferred = 106808 (1a138 hex) SF: 106808 bytes @ 0x0 Written: OK using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! Using usb_ether device TFTP from server 192.168.2.1; our IP address is 192.168.2.9 Filename 'u-boot.img'. Load address: 0x80200000 Loading: T #################################### 99.6 KiB/s done Bytes transferred = 528344 (80fd8 hex) SF: 528344 bytes @ 0x20000 Written: OK using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! Using usb_ether device TFTP from server 192.168.2.1; our IP address is 192.168.2.9 Filename 'zImage'. Load address: 0x80200000 Loading: T ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################### 1.3 MiB/s done Bytes transferred = 11002368 (a7e200 hex) using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC e0:92:8f:30:fa:68 HOST MAC e0:92:8f:30:fa:6a RNDIS ready high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! Using usb_ether device TFTP from server 192.168.2.1; our IP address is 192.168.2.9 Filename 'am335x-iec61850-module_flashing.dtb'. Load address: 0x80f80000 Loading: T ### 5.9 KiB/s done Bytes transferred = 32277 (7e15 hex) Kernel image @ 0x80200000 [ 0x000000 - 0xa7e200 ] ## Flattened Device Tree blob at 80f80000 Booting using the fdt blob at 0x80f80000 Loading Device Tree to 8fb36000, end 8fb40e14 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.94-gdfb7d7b06-dirty (vipin@vipin-HP-15-Notebook-PC) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09)) #8 PREEMPT Tue Sep 17 11:45:10 IST 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: AM335X-IEC61850-MODULE [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x8c800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (neon) [ 0.000000] random: get_random_bytes called from start_kernel+0xa4/0x434 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyO0,115200n8 g_ether.dev_addr=e0:92:8f:30:fa:68 g_ether.host_addr=e0:92:8f:30:fa:6a} ip=dhcp rw [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 190176K/262144K available (9216K kernel code, 312K rwdata, 2756K rodata, 7168K init, 254K bss, 22816K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (7168 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 313 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 255 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000047] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000061] OMAP clocksource: timer1 at 24000000 Hz [ 0.000240] timer_probe: no matching timers found [ 0.000468] Console: colour dummy device 80x30 [ 0.000505] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000514] This ensures that you still see kernel messages. Please [ 0.000521] update your kernel commandline. [ 0.000585] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.119004] pid_max: default: 32768 minimum: 301 [ 0.119252] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119270] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.120315] CPU: Testing write buffer coherency: ok [ 0.120392] CPU0: Spectre v2: using BPIALL workaround [ 0.121465] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.121653] rcu: Hierarchical SRCU implementation. [ 0.122100] EFI services will not be available. [ 0.123683] devtmpfs: initialized [ 0.132291] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.132786] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.132815] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.137148] pinctrl core: initialized pinctrl subsystem [ 0.138088] DMI not present or invalid. [ 0.138613] NET: Registered protocol family 16 [ 0.141571] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.168327] l4_wkup_cm:clk:0010:0: failed to disable [ 0.222522] cpuidle: using governor ladder [ 0.222571] cpuidle: using governor menu [ 0.228817] OMAP GPIO hardware version 0.1 [ 0.235877] platform 44e3e000.rtc: Cannot lookup hwmod 'rtc' [ 0.238861] No ATAGs? [ 0.238873] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.256758] edma 49000000.edma: TI EDMA DMA engine driver [ 0.261276] SCSI subsystem initialized [ 0.261869] media: Linux media interface: v0.10 [ 0.261919] videodev: Linux video capture interface: v2.00 [ 0.262037] pps_core: LinuxPPS API ver. 1 registered [ 0.262048] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.262078] PTP clock support registered [ 0.262121] EDAC MC: Ver: 3.0.0 [ 0.263414] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.264143] Advanced Linux Sound Architecture Driver Initialized. [ 0.265649] clocksource: Switched to clocksource timer1 [ 0.276345] NET: Registered protocol family 2 [ 0.277384] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.277423] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.277460] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.277492] TCP: Hash tables configured (established 2048 bind 2048) [ 0.277627] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.277651] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.277841] NET: Registered protocol family 1 [ 0.278533] RPC: Registered named UNIX socket transport module. [ 0.278550] RPC: Registered udp transport module. [ 0.278559] RPC: Registered tcp transport module. [ 0.278567] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.866017] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.867727] Initialise system trusted keyrings [ 0.868088] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.873901] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.874865] NFS: Registering the id_resolver key type [ 0.874917] Key type id_resolver registered [ 0.874928] Key type id_legacy registered [ 0.874984] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.878356] Key type asymmetric registered [ 0.878382] Asymmetric key parser 'x509' registered [ 0.878477] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.878494] io scheduler noop registered [ 0.878504] io scheduler deadline registered [ 0.878812] io scheduler cfq registered (default) [ 0.878828] io scheduler mq-deadline registered [ 0.878838] io scheduler kyber registered [ 0.880967] pinctrl-single 44e10800.pinmux: 142 pins, size 568 [ 0.944642] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.949717] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 [ 1.578698] console [ttyS0] enabled [ 1.584573] omap_rng 48310000.rng: Random Number Generator ver. 20 [ 1.590954] random: fast init done [ 1.594632] random: crng init done [ 1.614005] brd: module loaded [ 1.626005] loop: module loaded [ 1.633147] m25p80 spi0.0: unrecognized JEDEC id bytes: 1f, 32, 17 [ 1.640647] libphy: Fixed MDIO Bus: probed [ 1.650209] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator [ 1.660342] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 [ 1.673042] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator [ 1.683154] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 [ 1.700431] using random self ethernet address [ 1.704923] using random host ethernet address [ 1.709482] using host ethernet address: e0:92:8f:30:fa:6a} [ 1.709490] using self ethernet address: e0:92:8f:30:fa:68 [ 1.715795] usb0: HOST MAC e0:92:8f:30:fa:6a [ 1.725767] usb0: MAC e0:92:8f:30:fa:68 [ 1.729678] using random self ethernet address [ 1.734143] using random host ethernet address [ 1.738749] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 1.745397] g_ether gadget: g_ether ready [ 1.749983] i2c /dev entries driver [ 1.756221] cpu cpu0: Linked as a consumer to regulator.2 [ 1.761744] cpu cpu0: Dropping the link to regulator.2 [ 1.767252] cpu cpu0: Linked as a consumer to regulator.2 [ 1.772827] core: _opp_supported_by_regulators: OPP minuV: 931000 maxuV: 969000, not supported by regulator [ 1.782700] cpu cpu0: _opp_add: OPP not supported by regulators (300000000) [ 1.789929] core: _opp_supported_by_regulators: OPP minuV: 1078000 maxuV: 1122000, not supported by regulator [ 1.799928] cpu cpu0: _opp_add: OPP not supported by regulators (600000000) [ 1.807273] cpu cpu0: Dropping the link to regulator.2 [ 1.812642] cpuidle: enable-method property 'ti,am3352' found operations [ 1.820107] sdhci: Secure Digital Host Controller Interface driver [ 1.826465] sdhci: Copyright(c) Pierre Ossman [ 1.832382] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 [ 1.865416] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.873124] ledtrig-cpu: registered to indicate activity on CPUs [ 1.885362] NET: Registered protocol family 10 [ 1.891712] Segment Routing with IPv6 [ 1.895599] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.902585] NET: Registered protocol family 17 [ 1.907622] Key type dns_resolver registered [ 1.912222] omap_voltage_late_init: Voltage driver support not added [ 1.920045] Loading compiled-in X.509 certificates [ 1.938521] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 1.945621] mmc0: new high speed MMC card at address 0001 [ 1.952533] mmcblk0: mmc0:0001 008GB0 7.28 GiB [ 1.957896] mmcblk0boot0: mmc0:0001 008GB0 partition 1 8.00 MiB [ 1.964479] mmcblk0boot1: mmc0:0001 008GB0 partition 2 8.00 MiB [ 1.970902] mmcblk0rpmb: mmc0:0001 008GB0 partition 3 4.00 MiB, chardev (245:0) [ 1.980689] mmcblk0: p1 p2 [ 2.088592] g_ether gadget: high-speed config #2: RNDIS [ 2.115718] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 2.145811] Sending DHCP requests ..., OK [ 9.049790] IP-Config: Got DHCP answer from 192.168.2.1, my address is 192.168.2.9 [ 9.057450] IP-Config: Complete: [ 9.060701] device=usb0, hwaddr=e0:92:8f:30:fa:68, ipaddr=192.168.2.9, mask=255.255.255.0, gw=192.168.2.1 [ 9.070767] host=192.168.2.9, domain=, nis-domain=(none) [ 9.076557] bootserver=192.168.2.1, rootserver=192.168.2.1, rootpath= [ 9.076563] nameserver0=192.168.2.1 [ 9.088023] ALSA device list: [ 9.091016] No soundcards found. [ 9.094532] Warning: unable to open an initial console. [ 9.112731] Freeing unused kernel memory: 7168K [ 9.118019] Run /init as init process ************************************************************ Sitara Flash Fetcher Script v3.1 - 05/04/2020 This version is aligned with PROCESSOR-SDK-LINUX-AM335X v6.3 ************************************************************ Getting flasher.sh from server: 192.168.2.1 ******************************************** Sitara Flash Fetcher is complete. Executing flasher.sh. ******************************************** Calling Script=flasher.sh with SERVER_IP=192.168.2.1 [Unmounting all existing partitions on /dev/mmcblk0... ] [Creating Partitions on /dev/mmcblk0...] DISK SIZE - 7818182656 bytes ./flasher.sh: line 1: bc: not found CYLINDERS - [ 11.616206] mmcblk0: p1 p2 [ 11.658909] mmcblk0: p1 p2 [Done Partitioning.] Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xb0cdcb40 Device Boot Start End Sectors Size Id Type /dev/mmcblk0p1 2048 1640447 1638400 800M c W95 FAT32 (LBA) /dev/mmcblk0p2 1640448 15269887 13629440 6.5G 83 Linux [Making filesystems...] mkfs.fat 4.1 (2017-01-24) mkfs.fat: warning - lowercase labels might not work properly with DOS or Windows mke2fs 1.44.3 (10-July-2018) 64-bit filesystem support is not enabled. The larger fields afforded by this feature enable full-strength checksumming. Pass -O 64bit to rectify. Discarding device blocks: done Creating filesystem with 1703680 4k blocks and 425984 inodes Filesystem UUID: fc6aa70a-d79b-4493-8e26-cdbabcc5f276 Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done [Mounting Root Partition..] [ 22.779234] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [Fetching Filesystem..] [Extracting Filesystem..] / [Syncing..] [Unmounting Root Partition] eMMC Setup completed. ................... FLASHING COMPLETED ...................