U-Boot SPL 2021.01-g48e76495-dirty (Mar 11 2025 - 17:15:58 +0800) SYSFW ABI: 3.1 (firmware rev 0x0008 '8.6.4--v08.06.04 (Chill Capybar') SPL initial stack usage: 13424 bytes Trying to boot from MMC1 am654_sdhci mmc@fa10000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 Authentication passed Authentication passed Authentication passed Authentication passed Authentication passed init_env from device 9 not supported! Starting ATF on ARM64 core... NOTICE: BL31: v2.8(release):v2.8-226-g2fcd408bb3-dirty NOTICE: BL31: Built : 05:33:19, Feb 24 2023 U-Boot SPL 2021.01-g48e76495-dirty (Mar 11 2025 - 17:16:38 +0800) SYSFW ABI: 3.1 (firmware rev 0x0008 '8.6.4--v08.06.04 (Chill Capybar') Trying to boot from MMC1 am654_sdhci mmc@fa10000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sd-hs am654_sdhci mmc@fa10000: Couldn't find am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr12 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr25 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr50 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-ddr50 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr104 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-hs400 Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices U-Boot 2021.01-g48e76495-dirty (Mar 11 2025 - 17:16:38 +0800) ti-sci-sysreset sysreset-controller: set_state_simple op missing SoC: AM62X SR1.0 HS-FS Model: Texas Instruments AM625 SK DRAM: 2 GiB pinconfig run_err_led_pins_default: set_state_simple op missing single-pinctrl pinctrl@4084000: configuring pins for run_err_led_pins_default single-pinctrl pinctrl@4084000: reg/val 0x0x0000000004084000/0x00010007 single-pinctrl pinctrl@4084000: reg/val 0x0x0000000004084004/0x00010007 simple_bus bus@4000000: set_state_simple op missing simple_bus bus@f0000: set_state_simple op missing simple_bus bus@2b000000: set_state_simple op missing syscon syscon@43000000: set_state_simple op missing soc_ti_k3 chipid@14: set_state_simple op missing ti_sci system-controller@44043000: set_state_simple op missing simple_bus bus@48000000: set_state_simple op missing k3-secure-proxy mailbox@4d000000: set_state_simple op missing ti_sci system-controller@44043000: ti_sci_of_to_info: Acquiring notify channel failed. ret = -61 ti-sci-clk clock-controller: set_state_simple op missing pinconfig som_led1_pins_default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for som_led1_pins_default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4030/0x00010007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4098/0x00010007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f40a4/0x00050007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4094/0x00050007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41c0/0x00010007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41b4/0x00010007 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41bc/0x00010007 pinconfig main-uart0-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-uart0-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41c8/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41cc/0x00010000 ti-sci-pm-domains power-controller: set_state_simple op missing MMC: pinconfig main-mmc0-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-mmc0-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4220/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4218/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4214/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4210/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f420c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4208/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4204/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4200/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41fc/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f41f8/0x00050000 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sd-hs am654_sdhci mmc@fa10000: Couldn't find am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr12 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr25 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr50 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-ddr50 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-sdr104 am654_sdhci mmc@fa10000: Couldn't find ti,otap-del-sel-hs400 pinconfig main-mmc1-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-mmc1-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f423c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4234/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4230/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f422c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4228/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4224/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4240/0x00050000 am654_sdhci mmc@fa00000: Couldn't find ti,otap-del-sel-mmc-hs am654_sdhci mmc@fa00000: Couldn't find am654_sdhci mmc@fa00000: Couldn't find ti,otap-del-sel-ddr52 am654_sdhci mmc@fa00000: Couldn't find ti,otap-del-sel-hs200 am654_sdhci mmc@fa00000: Couldn't find ti,otap-del-sel-hs400 am654_sdhci mmc@fa20000: set_state_simple op missing am654_sdhci mmc@fa20000: Couldn't find ti,otap-del-sel-mmc-hs am654_sdhci mmc@fa20000: Couldn't find am654_sdhci mmc@fa20000: Couldn't find ti,otap-del-sel-ddr52 am654_sdhci mmc@fa20000: Couldn't find ti,otap-del-sel-hs200 am654_sdhci mmc@fa20000: Couldn't find ti,otap-del-sel-hs400 mmc@fa10000: 0, mmc@fa00000: 1, mmc@fa20000: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@2800000 Out: serial@2800000 Err: serial@2800000 pinconfig main-mdio1-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-mdio1-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4160/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f415c/0x00050000 pinconfig main-rgmii1-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-rgmii1-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f414c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4150/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4154/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4158/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4148/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4144/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4134/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4138/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f413c/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4140/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4130/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f412c/0x00010000 pinconfig main-rgmii2-pins-default: set_state_simple op missing single-pinctrl pinctrl@f4000: configuring pins for main-rgmii2-pins-default single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4184/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4188/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f418c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4190/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4180/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f417c/0x00050000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f416c/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4170/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4174/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4178/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4168/0x00010000 single-pinctrl pinctrl@f4000: reg/val 0x0x00000000000f4164/0x00010000 am65_cpsw_nuss ethernet@8000000: K3 CPSW: nuss_ver: 0x6BA01103 cpsw_ver: 0x6BA81103 ale_ver: 0x00290105 Ports:2 mdio_freq:1000000 Net: am65_cpsw_nuss_port port@1: set_state_simple op missing am65_cpsw_nuss ethernet@8000000: old gmii_sel: 00000002 am65_cpsw_nuss ethernet@8000000: gmii_sel PHY mode: 9, new gmii_sel: 00000002 eth0: ethernet@8000000port@1 Failed to load '/moons/update/moons_update_config.txt' ext4load /moons/update/moons_update_config.txt error use default model Model - 1 From EMMC update to EMMC Failed to load '/moons/update/tiboot3.bin' --- ext4load /moons/update/tiboot3.bin error !--- Failed to load '/moons/update/tispl.bin' --- ext4load /moons/update/tispl.bin error !--- Failed to load '/moons/update/u-boot.img' --- ext4load /moons/update/u-boot.img error !--- Failed to load '/moons/update/rootfs.ext4' --- ext4load /moons/update/rootfs.ext4 error ! --- Failed to load '/moons/update/Image' --- ext4load mmc 0:2 /moons/update/Image error ! --- Failed to load '/moons/update/tl62x-evm.dtb' --- ext4load mmc 0:2 /moons/update/tl62x-evm.dtb error ! --- Failed to load '/moons/update/fpga.bin' --- ext4load mmc 0:2 /moons/update/fpga.bin error ! --- 626777 bytes read in 7 ms (85.4 MiB/s) Debug Test cmd is ext4size mmc 0:2 /usr/Agile/fpga.bin ## Total Size = 0x00099059 = 626777 Bytes StrSizeis 99059 fpga.bin size is 626777 fpga_get_desc: found fpga descriptor #2 @ 0x00000000fffeb9a8 download fpga time: 3766 ------------------------------------------------------------------- --- fpga load mmc 0:2 OK ! --- MOONS MCA PAC U-BOOT version V1.1.1 please input passwordswitch to partitions #0, OK mmc0(part 0) is current device SD/MMC found on device 0 Failed to load 'boot.scr' Failed to load 'uEnv.txt' 18938368 bytes read in 107 ms (168.8 MiB/s) 44404 bytes read in 4 ms (10.6 MiB/s) Failed to load '/boot/tl62x-evm-devmem-rw.dtbo' ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 000000008fef2000, end 000000008fffffff ... OK Starting kernel ... ti-sci-pm-domains power-controller: set_state_simple op missing ti-sci-pm-domains power-controller: set_state_simple op missing ti-sci-pm-domains power-controller: set_state_simple op missing [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.168-rt83 (root@ubuntu) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 9.2.1 20191025, GNU ld (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 2.33.1.20191209) #14 SMP PREEMPT_RT Mon May 26 10:16:08 CST 2025 [ 0.000000] Machine model: TL62x-EVM [ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009c800000, size 3 MiB [ 0.000000] OF: reserved mem: initialized node ipc-memories@9c800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009cb00000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node m4f-dma-memory@9cb00000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009cc00000, size 14 MiB [ 0.000000] OF: reserved mem: initialized node m4f-memory@9cc00000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009da00000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@9da00000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009db00000, size 12 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@9db00000, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009c7fffff] [ 0.000000] node 0: [mem 0x000000009c800000-0x000000009e6fffff] [ 0.000000] node 0: [mem 0x000000009e700000-0x000000009e77ffff] [ 0.000000] node 0: [mem 0x000000009e780000-0x000000009fffffff] [ 0.000000] node 0: [mem 0x00000000a0000000-0x00000000ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] On node 0 totalpages: 524288 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 524288 pages, LIFO batch:63 [ 0.000000] cma: Reserved 144 MiB at 0x00000000f4000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s36032 r8192 d29504 u73728 [ 0.000000] pcpu-alloc: s36032 r8192 d29504 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000] Kernel command line: console=ttyS2,115200n8 isolcpus=1-3 earlycon=ns16550a,mmio32,0x02800000 root=PARTUUID=fbc97ce2-02 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1832960K/2097152K available (11072K kernel code, 1214K rwdata, 4300K rodata, 1792K init, 437K bss, 116736K reserved, 147456K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000 [ 0.000000] ITS [mem 0x01820000-0x0182ffff] [ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS [ 0.000000] ITS@0x0000000001820000: Devices Table too large, reduce ids 20->19 [ 0.000000] ITS@0x0000000001820000: allocated 524288 Devices @80800000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000000080030000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000080040000 [ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns [ 0.000000] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns [ 0.008522] Console: colour dummy device 80x25 [ 0.013113] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=200000) [ 0.023795] pid_max: default: 32768 minimum: 301 [ 0.028615] LSM: Security Framework initializing [ 0.033411] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.040994] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.051019] rcu: Hierarchical SRCU implementation. [ 0.056462] Platform MSI: msi-controller@1820000 domain created [ 0.062799] PCI/MSI: /bus@f0000/interrupt-controller@1800000/msi-controller@1820000 domain created [ 0.072072] EFI services will not be available. [ 0.077008] smp: Bringing up secondary CPUs ... [ 0.082430] Detected VIPT I-cache on CPU1 [ 0.086561] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000 [ 0.093599] GICv3: CPU1: using allocated LPI pending table @0x0000000080050000 [ 0.101036] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.108590] Detected VIPT I-cache on CPU2 [ 0.112712] GICv3: CPU2: found redistributor 2 region 0:0x00000000018c0000 [ 0.119746] GICv3: CPU2: using allocated LPI pending table @0x0000000080060000 [ 0.127164] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.134648] Detected VIPT I-cache on CPU3 [ 0.138770] GICv3: CPU3: found redistributor 3 region 0:0x00000000018e0000 [ 0.145803] GICv3: CPU3: using allocated LPI pending table @0x0000000080070000 [ 0.153216] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.159991] smp: Brought up 1 node, 4 CPUs [ 0.164195] SMP: Total of 4 processors activated. [ 0.169014] CPU features: detected: 32-bit EL0 Support [ 0.174279] CPU features: detected: CRC32 instructions [ 0.186719] CPU: All CPU(s) started at EL2 [ 0.190926] alternatives: patching kernel code [ 0.196523] devtmpfs: initialized [ 0.207329] KASLR disabled due to lack of seed [ 0.212038] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.222033] futex hash table entries: 1024 (order: 5, 131072 bytes, linear) [ 0.233586] pinctrl core: initialized pinctrl subsystem [ 0.239685] DMI not present or invalid. [ 0.244335] NET: Registered protocol family 16 [ 0.250800] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.258154] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.266246] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.274984] thermal_sys: Registered thermal governor 'step_wise' [ 0.275644] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.288826] ASID allocator initialised with 65536 entries [ 0.322161] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.329060] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.335948] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.342813] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.350950] cryptd: max_cpu_qlen set to 1000 [ 0.359072] k3-chipinfo 43000014.chipid: Family:AM62X rev:SR1.0 JTAGID[0x0bb7e02f] Detected [ 0.368413] vcc_5v0: supplied by vmain_pd [ 0.373068] vcc_3v3_sys: supplied by vmain_pd [ 0.377955] vdd_mmc1: supplied by vcc_3v3_sys [ 0.382951] vcc_1v8: supplied by vcc_3v3_sys [ 0.388486] iommu: Default domain type: Translated [ 0.393836] SCSI subsystem initialized [ 0.398136] mc: Linux media interface: v0.10 [ 0.402565] videodev: Linux video capture interface: v2.00 [ 0.408254] pps_core: LinuxPPS API ver. 1 registered [ 0.413330] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.422680] PTP clock support registered [ 0.426739] EDAC MC: Ver: 3.0.0 [ 0.430702] omap-mailbox 29000000.mailbox: omap mailbox rev 0x66fc9100 [ 0.437878] FPGA manager framework [ 0.441466] Advanced Linux Sound Architecture Driver Initialized. [ 0.448722] clocksource: Switched to clocksource arch_sys_counter [ 0.455249] VFS: Disk quotas dquot_6.6.0 [ 0.459325] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.471976] NET: Registered protocol family 2 [ 0.476727] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.485798] tcp_listen_portaddr_hash hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.494720] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.502974] TCP bind hash table entries: 16384 (order: 7, 917504 bytes, linear) [ 0.511463] TCP: Hash tables configured (established 16384 bind 16384) [ 0.518445] UDP hash table entries: 1024 (order: 5, 131072 bytes, linear) [ 0.525580] UDP-Lite hash table entries: 1024 (order: 5, 131072 bytes, linear) [ 0.533398] NET: Registered protocol family 1 [ 0.538396] RPC: Registered named UNIX socket transport module. [ 0.544492] RPC: Registered udp transport module. [ 0.549303] RPC: Registered tcp transport module. [ 0.554152] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.560763] NET: Registered protocol family 44 [ 0.565323] PCI: CLS 0 bytes, default 64 [ 0.570324] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.583342] Initialise system trusted keyrings [ 0.588159] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 0.600102] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.606788] NFS: Registering the id_resolver key type [ 0.612007] Key type id_resolver registered [ 0.616325] Key type id_legacy registered [ 0.620511] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.627375] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.635157] 9p: Installing v9fs 9p2000 file system support [ 0.676818] Key type asymmetric registered [ 0.681014] Asymmetric key parser 'x509' registered [ 0.686074] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.693641] io scheduler mq-deadline registered [ 0.698358] io scheduler kyber registered [ 0.704922] pinctrl-single 4084000.pinctrl: 34 pins, size 136 [ 0.711400] pinctrl-single f4000.pinctrl: 171 pins, size 684 [ 0.718377] pinctrl-single a40000.timesync-router: 512 pins, size 2048 [ 0.733543] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.747395] pinctrl-single f4000.pinctrl: pin PIN65 already requested by f4000.pinctrl; cannot claim for 30200000.dss [ 0.758274] pinctrl-single f4000.pinctrl: pin-65 (30200000.dss) status -22 [ 0.765308] pinctrl-single f4000.pinctrl: could not request pin 65 (PIN65) from group main-dss0-pins-default on device pinctrl-single [ 0.777674] tidss 30200000.dss: Error applying setting, reverse things back [ 0.784806] tidss: probe of 30200000.dss failed with error -22 [ 0.798962] brd: module loaded [ 0.811132] loop: module loaded [ 0.815349] megasas: 07.714.04.00-rc1 [ 0.823519] tun: Universal TUN/TAP device driver, 1.6 [ 0.829334] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 0.835773] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.841891] sky2: driver version 1.30 [ 0.846810] VFIO - User Level meta-driver version: 0.3 [ 0.853106] i2c /dev entries driver [ 0.858594] sdhci: Secure Digital Host Controller Interface driver [ 0.864995] sdhci: Copyright(c) Pierre Ossman [ 0.870077] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.877327] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 0.885654] optee: probing for conduit method. [ 0.890267] optee: revision 3.20 (8e74d476) [ 0.890556] optee: dynamic shared memory is enabled [ 0.900071] optee: initialized driver [ 0.906057] NET: Registered protocol family 17 [ 0.910814] 9pnet: Installing 9P2000 support [ 0.915282] Key type dns_resolver registered [ 0.920044] printk: bootconsole [ns16550a0]: printing thread started [ 0.920094] Loading compiled-in X.509 certificates [ 0.945422] ti-sci 44043000.system-controller: lpm region is required for suspend but not provided. [ 0.945511] ti-sci 44043000.system-controller: ABI: 3.1 (firmware rev 0x0008 '8.6.4--v08.06.04 (Chill Capybar') [ 1.019099] davinci-mcasp 2b00000.mcasp: IRQ common not found [ 1.024289] omap-gpmc 3b000000.memory-controller: GPMC revision 6.0 [ 1.024307] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 1.041600] physmap-flash 50000000.nor: physmap platform flash device: [mem 0x50000000-0x50ffffff] [ 1.041683] physmap-flash 50000000.nor: map_probe failed [ 1.055768] bq32k: probe of 0-0068 failed with error -5 [ 1.055844] omap_i2c 20000000.i2c: bus 0 rev0.12 at 400 kHz [ 1.061434] omap_i2c 20020000.i2c: bus 1 rev0.12 at 400 kHz [ 1.087320] printk: console [ttyS2]: printing thread started [ 1.087336] printk: console [ttyS2] enabled [ 1.087340] printk: bootconsole [ns16550a0] disabled [ 1.103424] printk: bootconsole [ns16550a0]: printing thread stopped [ 1.104869] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 30, base_baud = 3000000) is a 8250 [ 1.106134] omap8250 2820000.serial: unable to register 8250 port [ 1.106151] omap8250 2820000.serial: PM domain pd:153 will not be powered off [ 1.107350] omap8250 2840000.serial: unable to register 8250 port [ 1.108312] omap8250 2850000.serial: unable to register 8250 port [ 1.109222] 2860000.serial: ttyS7 at MMIO 0x2860000 (irq = 34, base_baud = 3000000) is a 8250 [ 1.173037] davinci_mdio 8000f00.mdio: Configuring MDIO in manual mode [ 1.173417] mdio_bus 8000f00.mdio: mii_bus 8000f00.mdio couldn't get reset GPIO [ 1.176818] am65-cpsw-nuss 8000000.ethernet: initializing am65 cpsw nuss version 0x6BA01103, cpsw version 0x6BA81103 Ports: 3 quirks:00000006 [ 1.177096] am65-cpsw-nuss 8000000.ethernet: Use random MAC address [ 1.177106] am65-cpsw-nuss 8000000.ethernet: initialized cpsw ale version 1.5 [ 1.177112] am65-cpsw-nuss 8000000.ethernet: ALE Table size 512 [ 1.188936] pps pps0: new PPS source ptp0 [ 1.201239] am65-cpsw-nuss 8000000.ethernet: CPTS ver 0x4e8a010c, freq:500000000, add_val:1 pps:1 [ 1.221913] am65-cpsw-nuss 8000000.ethernet: set new flow-id-base 19 [ 1.244843] rtc-ti-k3 2b1f0000.rtc: registered as rtc1 [ 1.354398] mmc0: CQHCI version 5.10 [ 1.360108] davinci-mcasp 2b00000.mcasp: IRQ common not found [ 1.360440] mmc1: CQHCI version 5.10 [ 1.385014] 2820000.serial: ttyS4 at MMIO 0x2820000 (irq = 31, base_baud = 3000000) is a 8250 [ 1.394812] 2840000.serial: ttyS5 at MMIO 0x2840000 (irq = 32, base_baud = 3000000) is a 8250 [ 1.398832] 2850000.serial: ttyS6 at MMIO 0x2850000 (irq = 33, base_baud = 3000000) is a 8250 [ 1.415486] davinci_mdio 8000f00.mdio: Configuring MDIO in manual mode [ 1.427036] mmc1: SDHCI controller on fa00000.mmc [fa00000.mmc] using ADMA 64-bit [ 1.427295] mmc0: SDHCI controller on fa10000.mmc [fa10000.mmc] using ADMA 64-bit [ 1.449712] davinci_mdio 8000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 1.459552] davinci_mdio 8000f00.mdio: phy[0]: device 8000f00.mdio:00, driver TI DP83867 [ 1.459566] davinci_mdio 8000f00.mdio: phy[1]: device 8000f00.mdio:01, driver TI DP83867 [ 1.461738] debugfs: Directory 'pd:53' with parent 'pm_genpd' already present! [ 1.461788] debugfs: Directory 'pd:52' with parent 'pm_genpd' already present! [ 1.461826] debugfs: Directory 'pd:51' with parent 'pm_genpd' already present! [ 1.462235] debugfs: Directory 'pd:182' with parent 'pm_genpd' already present! [ 1.482091] input: poweroff-signal as /devices/platform/poweroff-signal/input/input0 [ 1.490427] input: gpio-keys as /devices/platform/gpio-keys/input/input1 [ 1.502308] ALSA device list: [ 1.502319] No soundcards found. [ 1.521780] Waiting for root device PARTUUID=fbc97ce2-02... [ 1.541097] mmc0: Command Queue Engine enabled [ 1.541117] mmc0: new HS200 MMC card at address 0001 [ 1.551317] mmcblk0: mmc0:0001 88A398 7.28 GiB [ 1.551518] mmcblk0boot0: mmc0:0001 88A398 partition 1 4.00 MiB [ 1.551755] mmcblk0boot1: mmc0:0001 88A398 partition 2 4.00 MiB [ 1.551942] mmcblk0rpmb: mmc0:0001 88A398 partition 3 4.00 MiB, chardev (237:0) [ 1.553060] mmcblk0: p1 p2 [ 1.596963] EXT4-fs (mmcblk0p2): recovery complete [ 1.597219] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 1.597303] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 1.611086] devtmpfs: mounted [ 1.612416] Freeing unused kernel memory: 1792K [ 1.612524] Run /sbin/init as init process [ 1.649483] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Seeding 256 bits and crediting[ 1.705861] random: crng init done Saving 256 bits of creditable seed for next boot Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 1.800952] udevd[224]: starting version 3.2.11 [ 1.827636] udevd[225]: starting eudev-3.2.11 [ 2.165168] CAN device driver interface [ 2.199129] at24 1-0051: supply vcc not found, using dummy regulator [ 2.212739] at24 1-0051: 16384 byte 24c128 EEPROM, writable, 1 bytes/write [ 2.223343] m_can_platform 20701000.can: m_can device registered (irq=48, version=32) [ 2.421208] k3-m4-rproc 5000000.m4fss: assigned reserved memory node m4f-dma-memory@9cb00000 [ 2.430905] k3-m4-rproc 5000000.m4fss: configured M4 for remoteproc mode [ 2.431288] k3-m4-rproc 5000000.m4fss: local reset is deasserted for device [ 2.431545] remoteproc remoteproc0: 5000000.m4fss is available [ 2.432639] remoteproc remoteproc0: Direct firmware load for am62-mcu-m4f0_0-fw failed with error -2 [ 2.432657] remoteproc remoteproc0: powering up 5000000.m4fss [ 2.432688] remoteproc remoteproc0: Direct firmware load for am62-mcu-m4f0_0-fw failed with error -2 [ 2.432899] remoteproc remoteproc0: request_firmware failed: -2 [ 2.572600] platform 78000000.r5f: R5F core may have been powered on by a different host, programmed state (0) != actual state (1) [ 2.584932] platform 78000000.r5f: configured R5F for IPC-only mode [ 2.585231] platform 78000000.r5f: assigned reserved memory node r5f-dma-memory@9da00000 [ 2.587154] remoteproc remoteproc1: 78000000.r5f is available [ 2.587263] remoteproc remoteproc1: attaching to 78000000.r5f [ 2.618222] platform 78000000.r5f: R5F core initialized in IPC-only mode [ 2.618260] remoteproc1#vdev0buffer: assigned reserved memory node r5f-dma-memory@9da00000 [ 2.618414] remoteproc1#vdev0buffer: registered virtio0 (type 7) [ 2.618422] remoteproc remoteproc1: remote processor 78000000.r5f is now attached [ 2.997062] cdns-csi2rx: probe of 30101000.csi-bridge failed with error -22 [ 3.048284] virtio_rpmsg_bus virtio0: creating channel ti.ipc4.ping-pong addr 0xd [ 3.048466] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xe [ 3.070632] virtio_rpmsg_bus virtio0: rpmsg host is online [ 3.110737] rpmsg_client_sample virtio0.ti.ipc4.ping-pong.-1.13: new channel: 0x400 -> 0xd! [ 3.198557] usbcore: registered new interface driver usbfs [ 3.204849] usbcore: registered new interface driver hub [ 3.205387] usbcore: registered new device driver usb [ 3.253278] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.253323] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 3.253564] xhci-hcd xhci-hcd.1.auto: hcc params 0x0258fe6d hci version 0x110 quirks 0x0000000000010010 [ 3.276773] xhci-hcd xhci-hcd.1.auto: irq 494, io mem 0x31100000 [ 3.276967] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.276986] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 3.277007] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed done [ 3.277163] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 Version: modprobe_modules_1.1 [ 3.277171] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.277177] usb usb1: Product: xHCI Host Controller [ 3.277181] usb usb1: Manufacturer: Linux 5.10.168-rt83 xhci-hcd [ 3.277185] usb usb1: SerialNumber: xhci-hcd.1.auto [ 3.279074] hub 1-0:1.0: USB hub found [ 3.279118] hub 1-0:1.0: 1 port detected [ 3.281759] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.281874] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 3.281882] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.281888] usb usb2: Product: xHCI Host Controller [ 3.281893] usb usb2: Manufacturer: Linux 5.10.168-rt83 xhci-hcd [ 3.281897] usb usb2: SerialNumber: xhci-hcd.1.auto [ 3.283096] hub 2-0:1.0: USB hub found [ 3.283141] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.383479] usbcore: registered new interface driver smsc95xx [ 3.515760] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 3.641983] usb 1-1: New USB device found, idVendor=0424, idProduct=9e00, bcdDevice= 3.00 [ 3.642009] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.649360] smsc95xx v2.0.0 [ 3.786340] SMSC LAN8710/LAN8720 usb-001:002:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=usb-001:002:01, irq=POLL) [ 3.789241] smsc95xx 1-1:1.0 eth2: register 'smsc95xx' at usb-xhci-hcd.1.auto-1, smsc95xx USB 2.0 Ethernet, e2:ff:97:3a:16:e7 [ 3.951662] NET: Registered protocol family 10 [ 3.957645] Segment Routing with IPv6 [ 4.081883] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.108845] Bridge firewalling registered [ 4.185269] Initializing XFRM netlink socket Mounting configfs... [ 4.388258] using random self ethernet address [ 4.388276] using random host ethernet address sh: write error: No such device [ 4.409610] usb0: HOST MAC 1a:8d:d3:ad:31:ca [ 4.409631] usb0: MAC 76:33:89:3c:76:7c USB Gadget g1 enabled successfully! Using eth0 MAC address as serial number: 98:03:8a:87:9d:a9 Starting network: [ 4.436541] am65-cpsw-nuss 8000000.ethernet LAN1: renamed from eth0 [ 4.457591] am65-cpsw-nuss 8000000.ethernet LAN2: renamed from eth1 [ 4.478685] smsc95xx 1-1:1.0 LAN3: renamed from eth2 [ 4.569473] am65-cpsw-nuss 8000000.ethernet LAN1: PHY [8000f00.mdio:00] driver [TI DP83867] (irq=POLL) [ 4.569509] am65-cpsw-nuss 8000000.ethernet LAN1: configuring for phy/rgmii-rxid link mode [ 4.644482] am65-cpsw-nuss 8000000.ethernet LAN2: PHY [8000f00.mdio:01] driver [TI DP83867] (irq=POLL) [ 4.644515] am65-cpsw-nuss 8000000.ethernet LAN2: configuring for phy/rgmii-rxid link mode RTNETLINK answers: File exists RTNETLINK answers: File exists [ 4.734213] smsc95xx 1-1:1.0 LAN3: Link is Down FAIL Starting sshd: OK Starting vsftpd: OK