Setup started before i2c

Setup started

Boot Flags register: 34 3 62 2 C1

Dead battery status detected.

Patch Source: No configuration has been loaded

Received buffer: 0 30 0 0 80

Power Status: PD Controller is powered from VBUS

Step 1: Checking interrupt event

Received buffer: 0 0 0 0 0 0 0 0 0 0 2

Device ready.

Received buffer: 0 0 0 0 0 0 0 0 0 0 2

Step 2: Checking if device is in PTCH mode

MODE register: 50 54 43 48

Device is in PTCH mode.

Step 3: Writing PBMs

Step 4: Writing CMD1 with 'PBMs'

Step 5: Checking CMD1

CMD1 buffer: 50 42 4D 73

CMD1 check failed. Retrying...

CMD1 buffer: 0 0 0 0

CMD1 check passed.

CMD1 buffer: 0 0 0 0

Step 6: Checking DATA1

DATA1 buffer: 0 0 0 0

DATA1 check passed.

DATA1 buffer: 0 0 0 0

Step 7: Writing Patch Bundle

gSizeLowRegionArray: 13184

Step 8: Writing CMD1 with 'PBMc'

Step 9: Checking CMD1

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 50 42 4D 63

PBMc CMD1 check failed. Retrying...

CMD1 buffer: 0 0 0 0

PBMc CMD1 check passed.

CMD1 buffer: 0 0 0 0

Step 10: Checking DATA1

DATA1 buffer: 0 0 0 0

PBMc DATA1 check passed.

DATA1 buffer: 0 0 0 0

Step 11: Checking if patch is loaded

Received buffer: 0 0 0 0 0 0 0 0 0 0 3

Patch not loaded to the device.

Step 12: Checking if device is in APP mode

APP MODE register: 41 50 50 20

Device successfully transitioned to APP mode.

reading boot flags

Boot Flags register: 34 3 F2 C2 C1

Dead battery status detected.

Patch Source: A configuration has been loaded from I2C

Received buffer: 0 30 0 0 80

Power Status: PD Controller is powered from VBUS

Received buffer AutoNegSinkReg: 3E 40 1F 41 90 91 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Received buffer Tx Sink: 4 2C 91 1 10 2C D1 2 0 2C B1 4 0 F4 41 6 0 45 41 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Number of valid PDOs Tx Sink: 4

Received buffer Rx Source: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Number of valid PDOs Rx Source: 0

Received buffer PD status: 10 0 0 0

USBPD sequence executed.