## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.32-rc6 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1919652 Bytes = 1.8 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Boot ... Boot 1 Boot 2 Boot 3 Boot 4 Starting kernel ... Uncompressing Linux............................................................................................................................... done, booting the kernel. Linux version 2.6.32-rc6 (root@ubuntu) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #11 PREEMPT Wed Mar 12 17:47:32 HKT 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DA850/OMAP-L138 EVM Memory policy: ECC disabled, Data cache writeback DaVinci da850/omap-l138 variant 0x0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=tty2,115200n8 noinitrd rw ip=192.168.1.210 root=/dev/mmcblk0p2 mem=64M PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 60792KB available (3648K code, 280K data, 148K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs NET: Registered protocol family 16 driver_register Driver('dummy'), bus_type methods driver_add_groups Driver('dummy') ok, bus_type methods dirver_find Driver('dummy') ok, bus_type methods driver_register Driver('edma'), bus_type methods driver_add_groups Driver('edma') ok, bus_type methods dirver_find Driver('edma') ok, bus_type methods bio: create slab at 0 driver_register Driver('pca953x'), bus_type methods driver_add_groups Driver('pca953x') ok, bus_type methods dirver_find Driver('pca953x') ok, bus_type methods driver_register Driver('pcf857x'), bus_type methods driver_add_groups Driver('pcf857x') ok, bus_type methods dirver_find Driver('pcf857x') ok, bus_type methods SCSI subsystem initialized driver_register Driver('Generic PHY'), bus_type methods driver_add_groups Driver('Generic PHY') ok, bus_type methods dirver_find Driver('Generic PHY') ok, bus_type methods driver_register Driver('nop_usb_xceiv'), bus_type methods driver_add_groups Driver('nop_usb_xceiv') ok, bus_type methods dirver_find Driver('nop_usb_xceiv') ok, bus_type methods driver_register Driver('usbfs'), bus_type methods driver_add_groups Driver('usbfs') ok, bus_type methods dirver_find Driver('usbfs') ok, bus_type methods usbcore: registered new interface driver usbfs driver_register Driver('hub'), bus_type methods driver_add_groups Driver('hub') ok, bus_type methods dirver_find Driver('hub') ok, bus_type methods usbcore: registered new interface driver hub driver_register Driver('usb'), bus_type methods driver_add_groups Driver('usb') ok, bus_type methods dirver_find Driver('usb') ok, bus_type methods usbcore: registered new device driver usb driver_register Driver('i2c_davinci'), bus_type methods driver_add_groups Driver('i2c_davinci') ok, bus_type methods dirver_find Driver('i2c_davinci') ok, bus_type methods driver_register Driver('vpss'), bus_type methods driver_add_groups Driver('vpss') ok, bus_type methods dirver_find Driver('vpss') ok, bus_type methods Switching to clocksource timer0_1 musb_hdrc: version 6.0, cppi4.1-dma, host, debug=0 driver_register Driver('musb_hdrc'), bus_type methods driver_add_groups Driver('musb_hdrc') ok, bus_type methods Waiting for USB PHY clock good... musb_hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected dirver_find Driver('musb_hdrc') ok, bus_type methods NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: RMII PHY configured, MII PHY will not be functional driver_register Driver('cpuidle-davinci'), bus_type methods driver_add_groups Driver('cpuidle-davinci') ok, bus_type methods dirver_find Driver('cpuidle-davinci') ok, bus_type methods driver_register Driver('davinci-mcbsp'), bus_type methods driver_add_groups Driver('davinci-mcbsp') ok, bus_type methods McBSP:Probed McBSP1 dirver_find Driver('davinci-mcbsp') ok, bus_type methods JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 118 io scheduler noop registered io scheduler anticipatory registered (default) driver_register Driver('da8xx_lcdc'), bus_type methods driver_add_groups Driver('da8xx_lcdc') ok, bus_type methods da8xx_lcdc da8xx_lcdc.0: GLCD: Found INNOLUX_AT050TN22 panel Console: switching to colour frame buffer device 100x30 dirver_find Driver('da8xx_lcdc') ok, bus_type methods driver_register Driver('davincifb'), bus_type methods driver_add_groups Driver('davincifb') ok, bus_type methods dirver_find Driver('davincifb') ok, bus_type methods Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled driver_register Driver('serial8250'), bus_type methods driver_add_groups Driver('serial8250') ok, bus_type methods serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A console [ttyS2] enabled dirver_find Driver('serial8250') ok, bus_type methods brd: module loaded driver_register Driver('at24'), bus_type methods driver_add_groups Driver('at24') ok, bus_type methods dirver_find Driver('at24') ok, bus_type methods driver_register Driver('sd'), bus_type methods driver_add_groups Driver('sd') ok, bus_type methods dirver_find Driver('sd') ok, bus_type methods driver_register Driver('ahci'), bus_type methods driver_add_groups Driver('ahci') ok, bus_type methods ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci ata1: SATA max UDMA/133 irq 67 dirver_find Driver('ahci') ok, bus_type methods driver_register Driver('m25p80'), bus_type methods driver_add_groups Driver('m25p80') ok, bus_type methods dirver_find Driver('m25p80') ok, bus_type methods driver_register Driver('davinci_nand'), bus_type methods driver_add_groups Driver('davinci_nand') ok, bus_type methods NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit) NAND_ECC_NONE selected by board driver. This is not recommended !! Bad block table not found for chip 0 Bad block table not found for chip 0 Scanning device for bad blocks Bad eraseblock 778 at 0x000006140000 Bad eraseblock 1040 at 0x000008200000 Bad eraseblock 1202 at 0x000009640000 Bad eraseblock 1435 at 0x00000b360000 Bad eraseblock 2026 at 0x00000fd40000 Creating 6 MTD partitions on "davinci_nand.1": 0x000000000000-0x000000020000 : "u-boot env" 0x000000020000-0x000000040000 : "UBL" 0x000000040000-0x0000000c0000 : "u-boot" 0x000000300000-0x000000500000 : "kernel" 0x000000500000-0x000002500000 : "filesystem" 0x000002500000-0x000010000000 : "user" davinci_nand davinci_nand.1: controller rev. 2.5 dirver_find Driver('davinci_nand') ok, bus_type methods driver_register Driver('dm_spi'), bus_type methods driver_add_groups Driver('dm_spi') ok, bus_type methods davinci SPI Controller driver at 0xfef0e000 (irq = 56) use_dma=1 dirver_find Driver('dm_spi') ok, bus_type methods console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver driver_register Driver('ohci'), bus_type methods driver_add_groups Driver('ohci') ok, bus_type methods ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 ohci ohci.0: irq 59, io mem 0x01e25000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected dirver_find Driver('ohci') ok, bus_type methods Initializing USB Mass Storage driver... driver_register Driver('usb-storage'), bus_type methods driver_add_groups Driver('usb-storage') ok, bus_type methods dirver_find Driver('usb-storage') ok, bus_type methods usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice driver_register Driver('atkbd'), bus_type methods driver_add_groups Driver('atkbd') ok, bus_type methods dirver_find Driver('atkbd') ok, bus_type methods driver_register Driver('xtkbd'), bus_type methods driver_add_groups Driver('xtkbd') ok, bus_type methods dirver_find Driver('xtkbd') ok, bus_type methods driver_register Driver('ads7846'), bus_type methods driver_add_groups Driver('ads7846') ok, bus_type methods ads7846 spi1.0: touchscreen, irq 200 input: ADS7846 Touchscreen as /devices/platform/dm_spi.1/spi1.0/input/input0 dirver_find Driver('ads7846') ok, bus_type methods driver_register Driver('omap_rtc'), bus_type methods driver_add_groups Driver('omap_rtc') ok, bus_type methods omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected dirver_find Driver('omap_rtc') ok, bus_type methods i2c /dev entries driver driver_register Driver('dev_driver'), bus_type methods driver_add_groups Driver('dev_driver') ok, bus_type methods ata1: SATA link down (SStatus 0 SControl 300) dirver_find Driver('dev_driver') ok, bus_type methods driver_register Driver('ds1682'), bus_type methods driver_add_groups Driver('ds1682') ok, bus_type methods dirver_find Driver('ds1682') ok, bus_type methods Linux video capture interface: v2.00 driver_register Driver('tw9910'), bus_type methods driver_add_groups Driver('tw9910') ok, bus_type methods dirver_find Driver('tw9910') ok, bus_type methods driver_register Driver('camera'), bus_type methods driver_add_groups Driver('camera') ok, bus_type methods dirver_find Driver('camera') ok, bus_type methods driver_register Driver('soc-camera-pdrv'), bus_type methods driver_add_groups Driver('soc-camera-pdrv') ok, bus_type methods dirver_find Driver('soc-camera-pdrv') ok, bus_type methods vpfe_init driver_register Driver('vpfe-capture'), bus_type methods driver_add_groups Driver('vpfe-capture') ok, bus_type methods dirver_find Driver('vpfe-capture') ok, bus_type methods driver_register Driver('watchdog'), bus_type methods driver_add_groups Driver('watchdog') ok, bus_type methods watchdog watchdog: heartbeat 60 sec dirver_find Driver('watchdog') ok, bus_type methods cpuidle: using governor ladder cpuidle: using governor menu driver_register Driver('SEED_txl_mmcblk'), bus_type methods driver_add_groups Driver('SEED_txl_mmcblk') ok, bus_type methods dirver_find Driver('SEED_txl_mmcblk') ok, bus_type methods driver_register Driver('davinci_mmc'), bus_type methods driver_add_groups Driver('davinci_mmc') ok, bus_type methods davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode dirver_find Driver('davinci_mmc') ok, bus_type methods driver_register Driver('generic-usb'), bus_type methods driver_add_groups Driver('generic-usb') ok, bus_type methods dirver_find Driver('generic-usb') ok, bus_type methods driver_register Driver('usbhid'), bus_type methods driver_add_groups Driver('usbhid') ok, bus_type methods dirver_find Driver('usbhid') ok, bus_type methods usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused i2c1 Clocks: disable unused emac Clocks: disable unused mcasp Clocks: disable unused mcbsp0 driver_register Driver('cpufreq-davinci'), bus_type methods driver_add_groups Driver('cpufreq-davinci') ok, bus_type methods dirver_find Driver('cpufreq-davinci') ok, bus_type methods driver_register Driver('davinci_emac'), bus_type methods driver_add_groups Driver('davinci_emac') ok, bus_type methods davinci_emac_probe: using random MAC addr: 5a:0a:46:9d:88:5e emac-mii: probed dirver_find Driver('davinci_emac') ok, bus_type methods omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 1234 mmcblk0: mmc0:1234 SA04G 3.63 GiB mmcblk0: p1 p2 eth0: no PHY found IP-Config: Failed to open eth0 IP-Config: No network devices available. kjournald starting. Commit interval 5 seconds EXT3 FS on mmcblk0p2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 148K INIT: version 2.86 booting Please wait: booting... Starting udev modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory Populating dev cache Remounting root file system... WARNING: Couldn't open directory /lib/modules/2.6.32-rc6: No such file or directory FATAL: Could not open /lib/modules/2.6.32-rc6/modules.dep.temp for writing: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory root: mount: mounting rootfs on / failed: No such file or directory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... done. INIT: Entering runlevel: 5 Starting telnet daemon. modprobe: FATAL: Could not load /lib/modules/2.6.32-rc6/modules.dep: No such file or directory Starting syslogd/klogd: done Starting thttpd. ******** ********** ********** ******** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **** ****** ****** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ******** ********** ********** ******** SEED http://www.seeddsp.com seed ttyS2 SEED 2009.11 seed ttyS2 seed login: root root@seed:~# cd /home/root/omapl138/usr/share/ti/c6run-apps/ root@seed:~/omapl138/usr/share/ti/c6run-apps# ./loadmodules.sh CMEMK module: built on Mar 11 2014 at 15:58:21 Reference Linux version 2.6.32 File /work/dvsdk/linuxutils_2_25_05_11/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c CMEM Range Overlaps Kernel Physical - allowing overlap CMEM phys_start (0x2000000) overlaps kernel (0xc0000000 -> 0xc4000000) allocated heap buffer 0xc5000000 of size 0x2000000 cmemk initialized DSPLINK Module (1.65.00.02) created on Date: Mar 11 2014 Time: 16:19:02 root@seed:~/omapl138/usr/share/ti/c6run-apps# video_loopback_copy_omapl138.x470M V -r 720x576 -sh: video_loopback_copy_omapl138.x470MV: not found root@seed:~/omapl138/usr/share/ti/c6run-apps# cd .. root@seed:~/omapl138/usr/share/ti# cd ti-dmai-apps/ root@seed:~/omapl138/usr/share/ti/ti-dmai-apps# ./video_loopback_copy_omapl138.x47 -r 720x576 Cannot open /dev/video0 (No such file or directory) Failed to detect capture video standard root@seed:~/omapl138/usr/share/ti/ti-dmai-apps#