wifibt@wifibt-desktop:~$ ls bootup_log.txt Downloads Music target_cmd.txt temp tmp workdir Desktop examples.desktop Pictures targetfs Templates Ubuntu One Documents minicom.log Public targetfs.09252014_12.59 ti-dvsdk_omapl138-evm_04_03_00_06 Videos wifibt@wifibt-desktop:~$ cd ti-dvsdk_omapl138-evm_04_03_00_06/ wifibt@wifibt-desktop:~/ti-dvsdk_omapl138-evm_04_03_00_06$ ./setup.sh -------------------------------------------------------------------------------- TISDK setup script This script will set up your development host for dvsdk development. Parts of this script require administrator priviliges (sudo access). -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Verifying Linux host distribution Ubuntu 10.04 LTS found successfully, continuing.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will make sure you have the proper host support packages installed using the following command: sudo apt-get install xinetd tftpd nfs-kernel-server minicom build-essential libncurses5-dev uboot-mkimage autoconf automake Note! This command requires you to have administrator priviliges (sudo access) on your host. Press return to continue Reading package lists... Done Building dependency tree Reading state information... Done xinetd is already the newest version. tftpd is already the newest version. nfs-kernel-server is already the newest version. minicom is already the newest version. build-essential is already the newest version. libncurses5-dev is already the newest version. uboot-mkimage is already the newest version. autoconf is already the newest version. automake is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 448 not upgraded. Package verification and installation successfully completed -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- In which directory do you want to install the target filesystem?(if this directory does not exist it will be created) [ /home/wifibt/targetfs ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will extract the target filesystem to /home/wifibt/targetfs Note! This command requires you to have administrator priviliges (sudo access) on your host. Press return to continue /home/wifibt/targetfs already exists (r) rename existing filesystem (o) overwrite existing filesystem (s) skip filesystem extraction [r] s Skipping filesystem extraction WARNING! Keeping the previous filesystem may cause compatibility problems if you are upgrading the SDK -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will update the EXEC_DIR variables in the Rules.make file This will facilitate the SDK to install (with make install) rebuilt binaries in /home/wifibt/targetfs The files will be available from / on the target. This setting can be changed later by editing Rules.make and changing the EXEC_DIR variable. Press return to continue Rules.make edited successfully.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will export your target filesystem for NFS access. Note! This command requires you to have administrator priviliges (sudo access) on your host. Press return to continue /home/wifibt/targetfs already NFS exported, skipping.. * Stopping NFS kernel daemon [ OK ] * Unexporting directories for NFS kernel daemon... [ OK ] * Exporting directories for NFS kernel daemon... exportfs: Warning: /home/wifibt/targetfs2 does not exist exportfs: Warning: /home/wifbt/targetfs2 does not exist exportfs: Warning: TI does not exist [ OK ] * Starting NFS kernel daemon [ OK ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Which directory do you want to be your tftp root directory?(if this directory does not exist it will be created for you) [ /tftpboot ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the tftp server in the /tftpboot directory. Note! This command requires you to have administrator priviliges (sudo access) on your host. Press return to continue /tftpboot already exists, not creating.. /tftpboot/uImage-da850-omapl138-evm.bin already exists. The existing installed file can be renamed and saved under the new name. (r) rename (o) overwrite (s) skip copy [r] s Skipping copy of uImage-da850-omapl138-evm.bin, existing version will be used /etc/xinetd.d/tftp already exists.. /tftpboot already exported for TFTP, skipping.. Restarting tftp server * Stopping internet superserver xinetd [ OK ] * Starting internet superserver xinetd [ OK ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up minicom (serial communication application) for DVSDK development Which serial port do you want to use with minicom? [ /dev/ttyS0 ] Copied existing /home/wifibt/.minirc.dfl to /home/wifibt/.minirc.dfl.old Configuration saved to /home/wifibt/.minirc.dfl. You can change it further from inside minicom, see the Software Development Guide for more information. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the u-boot variables for booting the EVM. Autodetected the following ip address of your host, correct it if necessary [ 10.228.40.153 ] Select board memory: 1: 128MB 2: 64MB [ 1 ] 2 Select Linux kernel location: 1: TFTP 2: SD card 3: flash [ 1 ] 1 Select root file system location: 1: NFS 2: SD card [ 1 ] 1 Available kernel images in /tftpboot: 3051.uImage new_uImage uImage-da850-omapl138-evm.bin uImage-da850-omapl138-evm.bin.09252014_12.59 Which kernel image do you want to boot from TFTP? [ uImage-da850-omapl138-evm.bin ] 3051.uImage Resulting u-boot variable settings: setenv bootdelay 4 setenv baudrate 115200 setenv bootargs console=ttyS2,115200n8 noinitrd rw mem=32M@0xc0000000 root=/dev/nfs nfsroot=10.228.40.153:/home/wifibt/targetfs,nolock ip=dhcp setenv bootcmd 'dhcp;setenv serverip 10.228.40.153;tftpboot;bootm' setenv autoload no setenv serverip 10.228.40.153 setenv bootfile 3051.uImage -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Would you like to create a minicom script with the above parameters (y/n)? [ y ] Moving existing setup_uimage-tftp_fs-nfs.minicom to setup_uimage-tftp_fs-nfs.minicom.old Successfully wrote setup_uimage-tftp_fs-nfs.minicom Would you like to run the setup script now (y/n)? This requires you to connect the RS-232 cable between your host and EVM as well as your ethernet cable as described in the Quick Start Guide. Once answering 'y' on the prompt below you will have 300 seconds to connect the board and power cycle it before the setup times out. After successfully executing this script, your EVM will be set up. You will be able to connect to it by executing 'minicom -w' or if you prefer a windows host you can set up Tera Term as explained in the Software Developer's Guide. If you connect minicom or Tera Term and power cycle the board Linux will boot. [ y ] ~/ti-dvsdk_omapl138-evm_04_03_00_06 ~/ti-dvsdk_omapl138-evm_04_03_00_06 Welcome to minicom 2.4 OPTIONS: I18n Compiled on Jan 25 2010, 06:49:09. Port /dev/ttyS0 Press CTRL-A Z for help on special keys OMAP-L138 initialization passed! Booting TI User Boot Loader UBL Version: 1.65 UBL Flashtype: SPI Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. U-Boot 2009.11 (Dec 22 2010 - 00:27:22) I2C: ready DRAM: 64 MB MMC: davinci: 0 In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz Net: Ethernet PHY: GENERIC @ 0x00 Hit any key to stop autobo 0 U-Boot >setenv bootdelay 4 U-Boot >setenv baudrate 115200 ## Switch baudrate to 115200 bps and press ENTER ...U-Boot >setenv oldbootargs ${bootargs} U-Boot >ip=dhcp U-Boot >setenv autoload no U-Boot >setenv oldserverip ${serverip} U-Boot >setenv serverip 10.228.40.153 U-Boot >setenv bootfile 3051.uImage U-Boot >setenv oldbootcmd ${bootcmd} U-Boot >setenv bootcmd 'dhcp;setenv serverip 10.228.40.153;tftpboot;bootm' U-Boot >saveenv Saving Environment to SPI Flash... Erasing SPI flash...Writing to SPI flash...done U-Boot > CTRL-A Z for help |115200 8N1 | NOR | script setup_u | VT102 | Offline You can manually run minicom in the future with this setup script using: minicom -S setup_uimage-tftp_fs-nfs.minicom -------------------------------------------------------------------------------- TISDK setup completed! Please continue reading the Software Developer's Guide for more information on how to develop software on the EVM wifibt@wifibt-desktop:~/ti-dvsdk_omapl138-evm_04_03_00_06$ minicom -w Welcome to minicom 2.4 OPTIONS: I18n Compiled on Jan 25 2010, 06:49:09. Port /dev/ttyS0 Press CTRL-A Z for help on special keys OMAP-L138 initialization passed! Booting TI User Boot Loader UBL Version: 1.65 UBL Flashtype: SPI Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. U-Boot 2009.11 (Dec 22 2010 - 00:27:22) I2C: ready DRAM: 64 MB MMC: davinci: 0 In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz Net: Ethernet PHY: GENERIC @ 0x00 Hit any key to stop autoboot: 0 BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 44 *** Unhandled DHCP Option in OFFER/ACK: 46 *** Unhandled DHCP Option in OFFER/ACK: 44 *** Unhandled DHCP Option in OFFER/ACK: 46 DHCP client bound to address 10.228.40.242 Using device TFTP from server 10.228.40.153; our IP address is 10.228.40.242 Filename '3051.uImage'. Load address: 0xc0700000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### done Bytes transferred = 2314940 (2352bc hex) ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.37 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2314876 Bytes = 2.2 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.37 (titus@Titus) (gcc version 4.3.3 (GCC) ) #2 PREEMPT Thu Sep 25 13:06:27 IST 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DA850/OMAP-L138/AM18x EVM Memory policy: ECC disabled, Data cache writeback DaVinci da850/omap-l138 variant 0x0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS2,115200n8 noinitrd rw mem=32M@0xc0000000 root=/dev/nfs nfsroot=10.228.40.153:/home/wifibt/t argetfs,nolock ip=dhcp PID hash table entries: 128 (order: -3, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 32MB = 32MB total Memory: 27540k/27540k available, 5228k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xff000000 - 0xffe00000 ( 14 MB) vmalloc : 0xc2800000 - 0xfea00000 ( 962 MB) lowmem : 0xc0000000 - 0xc2000000 ( 32 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0032000 ( 168 kB) .text : 0xc0032000 - 0xc047e000 (4400 kB) .data : 0xc047e000 - 0xc04a8980 ( 171 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Preemptable hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 regulator: dummy: NET: Registered protocol family 16 WARNING: both McASP and McBSP are enabled, but they share pins. Only McASP will work. If you want McBSP support, disable McASP. WARNING: both McASP and UART1_AFE are enabled, but they share pins. Disable one of them. da850_evm_init: eHRPWM module 0 cannot be used since it is being used by MII interface da850_evm_init: eHRPWM module1 outputA cannot be used since it is being used by LCD da850_evm_init: eHRPWM module1 outputB cannot be used since it is being used by spi1 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pca953x 1-0020: failed reading register pca953x 1-0021: interrupt support not compiled in regulator: VDCDC1: 3200 <--> 3300 mV at 3300 mV regulator: VDCDC2: 1750 <--> 3300 mV at 3300 mV regulator: VDCDC3: 950 <--> 1350 mV at 1200 mV regulator: LDO1: 1800 mV regulator: LDO2: 1150 <--> 1300 mV at 1200 mV i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL) Advanced Linux Sound Architecture Driver Version 1.0.23. Bluetooth: Core ver 2.15 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Switching to clocksource timer0_1 musb-hdrc: version 6.0, host, debug=0 musb-hdrc musb-hdrc: dma type: dma-cppi41 Waiting for USB PHY clock good... musb-hdrc musb-hdrc: MUSB HDRC host driver musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected musb-hdrc musb-hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: MII PHY configured, RMII PHY will not be functional McBSP:Probed McBSP1 JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. msgmni has been set to 53 io scheduler noop registered (default) da8xx_lcdc da8xx_lcdc.0: GLCD: Found Sharp_LK043T1DG01 panel Console: switching to colour frame buffer device 60x34 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a AR7 serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a AR7 serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a AR7 console [ttyS2] enabled brd: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: m25p64 (8192 Kbytes) Creating 6 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "UBL" 0x000000010000-0x000000090000 : "U-Boot" 0x000000090000-0x0000000a0000 : "U-Boot-Env" 0x0000000a0000-0x000000320000 : "Kernel" 0x000000320000-0x000000720000 : "Filesystem" 0x0000007f0000-0x000000800000 : "MAC-Address" Read MAC addr from SPI Flash: 00:08:ee:03:5a:80 spi_davinci spi_davinci.1: Controller at 0xfef0e000 davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffffe davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. input: gpio-keys-polled as /devices/platform/gpio-keys-polled.1/input/input0 input: TPS6507x Touchscreen as /devices/platform/i2c-gpio.1/i2c-1/1-0048/input/input1 ata1: SATA link down (SStatus 0 SControl 300) omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected i2c /dev entries driver watchdog watchdog: heartbeat 60 sec Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCILL protocol initialized cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver 1-0018 supply IOVDD not found, using dummy regulator 1-0018 supply DVDD not found, using dummy regulator 1-0018 supply AVDD not found, using dummy regulator 1-0018 supply DRVDD not found, using dummy regulator asoc: tlv320aic3x-hifi <-> davinci-mcasp.0 mapping ok ALSA device list: #0: DA850/OMAP-L138 EVM nf_conntrack version 0.5.0 (430 buckets, 1720 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 Bluetooth: L2CAP ver 2.15 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=0:00, id=7c0f1) Sending DHCP requests . PHY: 0:00 - Link is Up - 100/Full ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 10.228.40.242 IP-Config: Complete: device=eth0, addr=10.228.40.242, mask=255.255.254.0, gw=10.228.41.254, host=10.228.40.242, domain=ap.mot-solutions.com, nis-domain=(none), bootserver=0.0.0.0, rootserver=10.228.40.153, rootpath= VFS: Mounted root (nfs filesystem) on device 0:13. Freeing init memory: 168K INIT: version 2.86 booting Please wait: booting... Starting udev udevd (601): /proc/601/oom_adj is deprecated, please use /proc/601/oom_score_adj instead. udev: starting version 141 Root filesystem already rw, not remounting Caching udev devnodes Populating dev cachemv: cannot rename '/tmp/devices': No such file or directory NET: Registered protocol family 10 logger: mount: mount point /proc/bus/usb does not exist ALSA: Restoring mixer settings... NOT configuring network interfaces: / is an NFS mount Found hardware: "" "" "" "" "" Hardware is initialized using a generic method /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #3 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #4 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #5 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #6 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #7 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #8 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #9 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #11 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #12 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #13 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #15 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #16 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #17 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #18 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #19 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #21 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #22 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #23 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #24 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #29 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #30 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #31 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #32 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #33 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #34 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #35 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #36 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #37 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #38 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #39 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #40 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #41 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #42 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #43 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #44 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #45 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #46 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #47 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #48 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #49 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #50 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #51 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #52 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #70 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #71 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #72 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #73 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #74 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #77 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #78 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #79 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #80 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #81 (No such file or directory) Fri Dec 23 12:42:00 UTC 2011 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. FATAL: Module cmemk not found. FATAL: Module dsplinkk not found. FATAL: Module dm365mmap not found. BusyBox v1.13.2 (2011-12-23 12:39:34 IST) multi-call binary Usage: mknod [OPTIONS] NAME TYPE MAJOR MINOR Create a special file (block, character, or pipe) Options: -m Create the special file using the specified mode (default a=rw) TYPEs include: b: Make a block device c or u: Make a character device p: Make a named pipe (MAJOR and MINOR are ignored) _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org arago ttyS2 Arago 2011.06 arago ttyS2 arago login: root root@arago:~# cd .. root@arago:/home# cd .. root@arago:/# root@arago:/# cd .. root@arago:/# ls bin etc linuxrc opt srv usr boot home media proc sys var dev lib mnt sbin tmp root@arago:/# cd dev root@arago:/dev# ls block random tty45 bus rfkill tty46 char rtc tty47 console rtc0 tty48 cpu_dma_latency shm tty49 fb snd tty5 fb0 tty tty50 full tty0 tty51 i2c-1 tty1 tty52 initctl tty10 tty53 input tty11 tty54 kmem tty12 tty55 kmsg tty13 tty56 log tty14 tty57 mem tty15 tty58 mtd0 tty16 tty59 mtd0ro tty17 tty6 mtd1 tty18 tty60 mtd1ro tty19 tty61 mtd2 tty2 tty62 mtd2ro tty20 tty63 mtd3 tty21 tty7 mtd3ro tty22 tty8 mtd4 tty23 tty9 mtd4ro tty24 ttyS0 mtd5 tty25 ttyS1 mtd5ro tty26 ttyS2 mtdblock0 tty27 ttyp0 mtdblock1 tty28 ttyp1 mtdblock2 tty29 ttyp2 mtdblock3 tty3 ttyp3 mtdblock4 tty30 ttyp4 mtdblock5 tty31 ttyp5 network_latency tty32 ttyp6 network_throughput tty33 ttyp7 null tty34 udev_network_queue ptmx tty35 urandom pts tty36 vcs ptyp0 tty37 vcs1 ptyp1 tty38 vcs2 ptyp2 tty39 vcsa ptyp3 tty4 vcsa1 ptyp4 tty40 vcsa2 ptyp5 tty41 watchdog ptyp6 tty42 zero ptyp7 tty43 ram0 tty44 root@arago:/dev# CTRL-A Z for help |115200 8N1 | NOR | Minicom 2.4 | VT102 | Offline