/*
 *  ======== ti_drivers_config.c ========
 *  Configured TI-Drivers module definitions
 *
 *  DO NOT EDIT - This file is generated for the LP_CC2652RSIP
 *  by the SysConfig tool.
 */

#include <stddef.h>
#include <stdint.h>

#ifndef DeviceFamily_CC26X2
#define DeviceFamily_CC26X2
#endif

#include <ti/devices/DeviceFamily.h>

#include "ti_drivers_config.h"

/*
 *  ============================= Display =============================
 */

#include <ti/display/Display.h>
#include <ti/display/DisplayUart.h>

#define CONFIG_Display_COUNT 1

#define Display_UARTBUFFERSIZE 128
static char displayUARTBuffer[Display_UARTBUFFERSIZE];

DisplayUart_Object displayUartObject;

const DisplayUart_HWAttrs displayUartHWAttrs = {
    .uartIdx      = CONFIG_DISPLAY_UART,
    .baudRate     = 115200,
    .mutexTimeout = (unsigned int)(-1),
    .strBuf       = displayUARTBuffer,
    .strBufLen    = Display_UARTBUFFERSIZE
};

const Display_Config Display_config[CONFIG_Display_COUNT] = {
    /* CONFIG_Display_0 */
    /* XDS110 UART */
    {
        .fxnTablePtr = &DisplayUartAnsi_fxnTable,
        .object      = &displayUartObject,
        .hwAttrs     = &displayUartHWAttrs
    },
};

const uint_least8_t Display_count = CONFIG_Display_COUNT;

/*
 *  =============================== AESCCM ===============================
 */

#include <ti/drivers/AESCCM.h>
#include <ti/drivers/aesccm/AESCCMCC26XX.h>

#define CONFIG_AESCCM_COUNT 1
AESCCMCC26XX_Object aesccmCC26XXObjects[CONFIG_AESCCM_COUNT];

/*
 *  ======== aesccmCC26XXHWAttrs ========
 */
const AESCCMCC26XX_HWAttrs aesccmCC26XXHWAttrs[CONFIG_AESCCM_COUNT] = {
    {
        .intPriority = (~0),
    },
};

const AESCCM_Config AESCCM_config[CONFIG_AESCCM_COUNT] = {
    {   /* CONFIG_AESCCM0 */
        .object  = &aesccmCC26XXObjects[CONFIG_AESCCM0],
        .hwAttrs = &aesccmCC26XXHWAttrs[CONFIG_AESCCM0]
    },
};

const uint_least8_t CONFIG_AESCCM0_CONST = CONFIG_AESCCM0;
const uint_least8_t AESCCM_count = CONFIG_AESCCM_COUNT;

/*
 *  =============================== AESCTR ===============================
 */

#include <ti/drivers/AESCTR.h>
#include <ti/drivers/aesctr/AESCTRCC26XX.h>

#define CONFIG_AESCTR_COUNT 1
AESCTRCC26XX_Object aesctrCC26XXObjects[CONFIG_AESCTR_COUNT];

/*
 *  ======== aesctrCC26XXHWAttrs ========
 */
const AESCTRCC26XX_HWAttrs aesctrCC26XXHWAttrs[CONFIG_AESCTR_COUNT] = {
    {
        .intPriority = (~0),
    },
};

const AESCTR_Config AESCTR_config[CONFIG_AESCTR_COUNT] = {
    {   /* CONFIG_AESCTR_0 */
        .object  = &aesctrCC26XXObjects[CONFIG_AESCTR_0],
        .hwAttrs = &aesctrCC26XXHWAttrs[CONFIG_AESCTR_0]
    },
};

const uint_least8_t CONFIG_AESCTR_0_CONST = CONFIG_AESCTR_0;
const uint_least8_t AESCTR_count = CONFIG_AESCTR_COUNT;

/*
 *  =============================== AESCTRDRBG ===============================
 */

#include <ti/drivers/AESCTRDRBG.h>
#include <ti/drivers/aesctrdrbg/AESCTRDRBGXX.h>

#define CONFIG_AESCTRDRBG_COUNT 1

/*
 *  ======== aesctrdrbgXXObjects ========
 */
AESCTRDRBGXX_Object aesctrdrbgXXObjects[CONFIG_AESCTRDRBG_COUNT];

/*
 *  ======== aesctrdrbgXXHWAttrs ========
 */
const AESCTRDRBGXX_HWAttrs aesctrdrbgXXHWAttrs[CONFIG_AESCTRDRBG_COUNT] = {
    /* CONFIG_AESCTRDRBG_0 */
    {
        .aesctrIndex = CONFIG_AESCTR_0
    },
};

/*
 *  ======== AESCTRDRBG_config ========
 */
const AESCTRDRBG_Config AESCTRDRBG_config[CONFIG_AESCTRDRBG_COUNT] = {
    /* CONFIG_AESCTRDRBG_0 */
    {
        .object = &aesctrdrbgXXObjects[CONFIG_AESCTRDRBG_0],
        .hwAttrs = &aesctrdrbgXXHWAttrs[CONFIG_AESCTRDRBG_0]
    },
};

const uint_least8_t CONFIG_AESCTRDRBG_0_CONST = CONFIG_AESCTRDRBG_0;
const uint_least8_t AESCTRDRBG_count = CONFIG_AESCTRDRBG_COUNT;

/*
 *  =============================== AESECB ===============================
 */

#include <ti/drivers/AESECB.h>
#include <ti/drivers/aesecb/AESECBCC26XX.h>

#define CONFIG_AESECB_COUNT 1
AESECBCC26XX_Object aesecbCC26XXObjects[CONFIG_AESECB_COUNT];

/*
 *  ======== aesecbCC26XXHWAttrs ========
 */
const AESECBCC26XX_HWAttrs aesecbCC26XXHWAttrs[CONFIG_AESECB_COUNT] = {
    {
        .intPriority = (~0),
    },
};

const AESECB_Config AESECB_config[CONFIG_AESECB_COUNT] = {
    {   /* CONFIG_AESECB0 */
        .object  = &aesecbCC26XXObjects[CONFIG_AESECB0],
        .hwAttrs = &aesecbCC26XXHWAttrs[CONFIG_AESECB0]
    },
};


const uint_least8_t CONFIG_AESECB0_CONST = CONFIG_AESECB0;
const uint_least8_t AESECB_count = CONFIG_AESECB_COUNT;

/*
 *  =============================== DMA ===============================
 */

#include <ti/drivers/dma/UDMACC26XX.h>
#include <ti/devices/cc13x2_cc26x2/driverlib/udma.h>
#include <ti/devices/cc13x2_cc26x2/inc/hw_memmap.h>

UDMACC26XX_Object udmaCC26XXObject;

const UDMACC26XX_HWAttrs udmaCC26XXHWAttrs = {
    .baseAddr        = UDMA0_BASE,
    .powerMngrId     = PowerCC26XX_PERIPH_UDMA,
    .intNum          = INT_DMA_ERR,
    .intPriority     = (~0)
};

const UDMACC26XX_Config UDMACC26XX_config[1] = {
    {
        .object         = &udmaCC26XXObject,
        .hwAttrs        = &udmaCC26XXHWAttrs,
    },
};

/*
 *  =============================== ECDH ===============================
 */

#include <ti/drivers/ECDH.h>
#include <ti/drivers/ecdh/ECDHCC26X2.h>

#define CONFIG_ECDH_COUNT 1

ECDHCC26X2_Object ecdhCC26X2Objects[CONFIG_ECDH_COUNT];

/*
 *  ======== ecdhCC26X2HWAttrs ========
 */
const ECDHCC26X2_HWAttrs ecdhCC26X2HWAttrs[CONFIG_ECDH_COUNT] = {
    {
        .intPriority = (~0),
    },
};

const ECDH_Config ECDH_config[CONFIG_ECDH_COUNT] = {
    {   /* CONFIG_ECDH0 */
        .object         = &ecdhCC26X2Objects[CONFIG_ECDH0],
        .hwAttrs        = &ecdhCC26X2HWAttrs[CONFIG_ECDH0]
    },
};

const uint_least8_t CONFIG_ECDH0_CONST = CONFIG_ECDH0;
const uint_least8_t ECDH_count = CONFIG_ECDH_COUNT;

/*
 *  =============================== GPIO ===============================
 */

#include <ti/drivers/GPIO.h>
#include <ti/drivers/gpio/GPIOCC26XX.h>

#define CONFIG_GPIO_COUNT 3

/*
 *  ======== gpioPinConfigs ========
 *  Array of Pin configurations
 */
GPIO_PinConfig gpioPinConfigs[] = {
    /* CONFIG_GPIO_BTN1 : LaunchPad Button BTN-1 (Left) */
    GPIOCC26XX_DIO_15 | GPIO_DO_NOT_CONFIG,
    /* CONFIG_GPIO_BTN2 : LaunchPad Button BTN-2 (Right) */
    GPIOCC26XX_DIO_14 | GPIO_DO_NOT_CONFIG,
    /* CONFIG_GPIO_0 */
    GPIOCC26XX_DIO_31 | GPIO_CFG_IN_NOPULL | GPIO_CFG_IN_INT_NONE,
};

/*
 *  ======== gpioCallbackFunctions ========
 *  Array of callback function pointers
 *
 *  NOTE: Unused callback entries can be omitted from the callbacks array to
 *  reduce memory usage by enabling callback table optimization
 *  (GPIO.optimizeCallbackTableSize = true)
 */
GPIO_CallbackFxn gpioCallbackFunctions[] = {
    /* CONFIG_GPIO_BTN1 : LaunchPad Button BTN-1 (Left) */
    NULL,
    /* CONFIG_GPIO_BTN2 : LaunchPad Button BTN-2 (Right) */
    NULL,
    /* CONFIG_GPIO_0 */
    NULL,
};

const uint_least8_t CONFIG_GPIO_BTN1_CONST = CONFIG_GPIO_BTN1;
const uint_least8_t CONFIG_GPIO_BTN2_CONST = CONFIG_GPIO_BTN2;
const uint_least8_t CONFIG_GPIO_0_CONST = CONFIG_GPIO_0;

/*
 *  ======== GPIOCC26XX_config ========
 */
const GPIOCC26XX_Config GPIOCC26XX_config = {
    .pinConfigs = (GPIO_PinConfig *)gpioPinConfigs,
    .callbacks = (GPIO_CallbackFxn *)gpioCallbackFunctions,
    .numberOfPinConfigs = 3,
    .numberOfCallbacks = 3,
    .intPriority = (~0)
};

/*
 *  =============================== NVS ===============================
 */

#include <ti/drivers/NVS.h>
#include <ti/drivers/nvs/NVSCC26XX.h>

/*
 *  NVSCC26XX Internal NVS flash region definitions
 *
 * Place uninitialized char arrays at addresses
 * corresponding to the 'regionBase' addresses defined in
 * the configured NVS regions. These arrays are used as
 * place holders so that the linker will not place other
 * content there.
 *
 * For GCC targets, the char arrays are each placed into
 * the shared ".nvs" section. The user must add content to
 * their GCC linker command file to place the .nvs section
 * at the lowest 'regionBase' address specified in their NVS
 * regions.
 */

#if defined(__TI_COMPILER_VERSION__) || defined(__clang__)

static char flashBuf0[0x4000] __attribute__ ((retain, noinit, location(0x48000)));

#elif defined(__IAR_SYSTEMS_ICC__)

__no_init static char flashBuf0[0x4000] @ 0x48000;

#elif defined(__GNUC__)

__attribute__ ((section (".nvs")))
static char flashBuf0[0x4000];

#endif

NVSCC26XX_Object nvsCC26XXObjects[1];

static const NVSCC26XX_HWAttrs nvsCC26XXHWAttrs[1] = {
    /* CONFIG_NVSINTERNAL */
    {
        .regionBase = (void *) flashBuf0,
        .regionSize = 0x4000
    },
};

#define CONFIG_NVS_COUNT 1

const NVS_Config NVS_config[CONFIG_NVS_COUNT] = {
    /* CONFIG_NVSINTERNAL */
    {
        .fxnTablePtr = &NVSCC26XX_fxnTable,
        .object = &nvsCC26XXObjects[0],
        .hwAttrs = &nvsCC26XXHWAttrs[0],
    },
};

const uint_least8_t CONFIG_NVSINTERNAL_CONST = CONFIG_NVSINTERNAL;
const uint_least8_t NVS_count = CONFIG_NVS_COUNT;

/*
 *  =============================== PIN ===============================
 */
#include <ti/drivers/PIN.h>
#include <ti/drivers/pin/PINCC26XX.h>

#define CONFIG_PIN_COUNT 5

const PIN_Config BoardGpioInitTable[CONFIG_PIN_COUNT + 1] = {
    /* LaunchPad Button BTN-1 (Left), Parent Signal: CONFIG_GPIO_BTN1 GPIO Pin, (DIO15) */
    CONFIG_PIN_BTN1 | PIN_INPUT_EN | PIN_PULLUP | PIN_IRQ_DIS,
    /* LaunchPad Button BTN-2 (Right), Parent Signal: CONFIG_GPIO_BTN2 GPIO Pin, (DIO14) */
    CONFIG_PIN_BTN2 | PIN_INPUT_EN | PIN_PULLUP | PIN_IRQ_DIS,
    /* Parent Signal: CONFIG_GPIO_0 GPIO Pin, (DIO31) */
    CONFIG_PIN_0 | PIN_INPUT_EN | PIN_NOPULL | PIN_IRQ_DIS,
    /* XDS110 UART, Parent Signal: CONFIG_DISPLAY_UART TX, (DIO13) */
    CONFIG_PIN_UART_TX | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL | PIN_DRVSTR_MED,
    /* XDS110 UART, Parent Signal: CONFIG_DISPLAY_UART RX, (DIO12) */
    CONFIG_PIN_UART_RX | PIN_INPUT_EN | PIN_PULLDOWN | PIN_IRQ_DIS,

    PIN_TERMINATE
};

const PINCC26XX_HWAttrs PINCC26XX_hwAttrs = {
    .intPriority = (~0),
    .swiPriority = 0
};

/*
 *  =============================== Power ===============================
 */
#include <ti/drivers/Power.h>
#include <ti/drivers/power/PowerCC26X2.h>
#include "ti_drivers_config.h"

extern void PowerCC26XX_standbyPolicy(void);
extern bool PowerCC26XX_calibrate(unsigned int);

const PowerCC26X2_Config PowerCC26X2_config = {
    .enablePolicy             = true,
    .policyInitFxn            = NULL,
    .policyFxn                = PowerCC26XX_standbyPolicy,
    .calibrateFxn             = PowerCC26XX_calibrate,
    .calibrateRCOSC_LF        = true,
    .calibrateRCOSC_HF        = true,
    .enableTCXOFxn            = NULL
};


/*
 *  =============================== RF Driver ===============================
 */
#include <ti/drivers/rf/RF.h>

/*
 * Platform-specific driver configuration
 */
const RFCC26XX_HWAttrsV2 RFCC26XX_hwAttrs = {
    .hwiPriority        = (~0),
    .swiPriority        = (uint8_t)0,
    .xoscHfAlwaysNeeded = true,
    .globalCallback     = NULL,
    .globalEventMask    = 0
};


/*
 *  =============================== TRNG ===============================
 */

#include <ti/drivers/TRNG.h>
#include <ti/drivers/trng/TRNGCC26XX.h>

#define CONFIG_TRNG_COUNT 1

TRNGCC26XX_Object trngCC26XXObjects[CONFIG_TRNG_COUNT];

/*
 *  ======== trngCC26XXHWAttrs ========
 */
static const TRNGCC26XX_HWAttrs trngCC26XXHWAttrs[CONFIG_TRNG_COUNT] = {
    {
        .intPriority = (~0),
        .swiPriority = 0,
        .samplesPerCycle = 240000
    },
};

const TRNG_Config TRNG_config[CONFIG_TRNG_COUNT] = {
    {   /* CONFIG_TRNG_0 */
        .object         = &trngCC26XXObjects[CONFIG_TRNG_0],
        .hwAttrs        = &trngCC26XXHWAttrs[CONFIG_TRNG_0]
    },
};

const uint_least8_t CONFIG_TRNG_0_CONST = CONFIG_TRNG_0;
const uint_least8_t TRNG_count = CONFIG_TRNG_COUNT;

/*
 *  =============================== Temperature ===============================
 */
#include <ti/drivers/Temperature.h>
#include <ti/drivers/temperature/TemperatureCC26X2.h>

const TemperatureCC26X2_Config TemperatureCC26X2_config = {
    .intPriority = (~0),
};

/*
 *  =============================== UART ===============================
 */

#include <ti/drivers/UART.h>
#include <ti/drivers/uart/UARTCC26XX.h>
#include <ti/drivers/Power.h>
#include <ti/drivers/power/PowerCC26X2.h>
#include <ti/devices/cc13x2_cc26x2/inc/hw_memmap.h>
#include <ti/devices/cc13x2_cc26x2/inc/hw_ints.h>

#define CONFIG_UART_COUNT 1

UARTCC26XX_Object uartCC26XXObjects[CONFIG_UART_COUNT];

static unsigned char uartCC26XXRingBuffer0[32];

static const UARTCC26XX_HWAttrsV2 uartCC26XXHWAttrs[CONFIG_UART_COUNT] = {
  {
    .baseAddr           = UART1_BASE,
    .intNum             = INT_UART1_COMB,
    .intPriority        = (~0),
    .swiPriority        = 0,
    .powerMngrId        = PowerCC26X2_PERIPH_UART1,
    .ringBufPtr         = uartCC26XXRingBuffer0,
    .ringBufSize        = sizeof(uartCC26XXRingBuffer0),
    .rxPin              = IOID_12,
    .txPin              = IOID_13,
    .ctsPin             = PIN_UNASSIGNED,
    .rtsPin             = PIN_UNASSIGNED,
    .txIntFifoThr       = UARTCC26XX_FIFO_THRESHOLD_1_8,
    .rxIntFifoThr       = UARTCC26XX_FIFO_THRESHOLD_4_8,
    .errorFxn           = NULL
  },
};

const UART_Config UART_config[CONFIG_UART_COUNT] = {
    {   /* CONFIG_DISPLAY_UART */
        .fxnTablePtr = &UARTCC26XX_fxnTable,
        .object      = &uartCC26XXObjects[CONFIG_DISPLAY_UART],
        .hwAttrs     = &uartCC26XXHWAttrs[CONFIG_DISPLAY_UART]
    },
};

const uint_least8_t CONFIG_DISPLAY_UART_CONST = CONFIG_DISPLAY_UART;
const uint_least8_t UART_count = CONFIG_UART_COUNT;

#include <stdbool.h>

#include <ti/devices/cc13x2_cc26x2/driverlib/ioc.h>
#include <ti/devices/cc13x2_cc26x2/driverlib/cpu.h>

#include <ti/drivers/pin/PINCC26XX.h>

/*
 *  ======== Board_sendExtFlashByte ========
 */
void Board_sendExtFlashByte(PIN_Handle pinHandle, uint8_t byte)
{
    uint8_t i;

    /* SPI Flash CS */
    PIN_setOutputValue(pinHandle, IOID_20, 0);

    for (i = 0; i < 8; i++) {
        PIN_setOutputValue(pinHandle, IOID_10, 0);  /* SPI Flash CLK */

        /* SPI Flash MOSI */
        PIN_setOutputValue(pinHandle, IOID_9, (byte >> (7 - i)) & 0x01);
        PIN_setOutputValue(pinHandle, IOID_10, 1);  /* SPI Flash CLK */

        /*
         * Waste a few cycles to keep the CLK high for at
         * least 45% of the period.
         * 3 cycles per loop: 8 loops @ 48 Mhz = 0.5 us.
         */
        CPUdelay(8);
    }

    PIN_setOutputValue(pinHandle, IOID_10, 0);  /* CLK */
    PIN_setOutputValue(pinHandle, IOID_20, 1);  /* CS */

    /*
     * Keep CS high at least 40 us
     * 3 cycles per loop: 700 loops @ 48 Mhz ~= 44 us
     */
    CPUdelay(700);
}

/*
 *  ======== Board_wakeUpExtFlash ========
 */
void Board_wakeUpExtFlash(void)
{
    PIN_Config extFlashPinTable[] = {
        /* SPI Flash CS */
        IOID_20 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL |
                PIN_INPUT_DIS | PIN_DRVSTR_MED,
        PIN_TERMINATE
    };
    PIN_State extFlashPinState;
    PIN_Handle extFlashPinHandle = PIN_open(&extFlashPinState, extFlashPinTable);

    /*
     *  To wake up we need to toggle the chip select at
     *  least 20 ns and ten wait at least 35 us.
     */

    /* Toggle chip select for ~20ns to wake ext. flash */
    PIN_setOutputValue(extFlashPinHandle, IOID_20, 0);
    /* 3 cycles per loop: 1 loop @ 48 Mhz ~= 62 ns */
    CPUdelay(1);
    PIN_setOutputValue(extFlashPinHandle, IOID_20, 1);
    /* 3 cycles per loop: 560 loops @ 48 Mhz ~= 35 us */
    CPUdelay(560);

    PIN_close(extFlashPinHandle);
}

/*
 *  ======== Board_shutDownExtFlash ========
 */
void Board_shutDownExtFlash(void)
{
    /*
     *  To be sure we are putting the flash into sleep and not waking it,
     *  we first have to make a wake up call
     */
    Board_wakeUpExtFlash();

    PIN_Config extFlashPinTable[] = {
        /* SPI Flash CS*/
        IOID_20 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_HIGH | PIN_PUSHPULL |
                PIN_INPUT_DIS | PIN_DRVSTR_MED,
        /* SPI Flash CLK */
        IOID_10 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL |
                PIN_INPUT_DIS | PIN_DRVSTR_MED,
        /* SPI Flash MOSI */
        IOID_9 | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL |
                PIN_INPUT_DIS | PIN_DRVSTR_MED,
        /* SPI Flash MISO */
        IOID_8 | PIN_INPUT_EN | PIN_PULLDOWN,
        PIN_TERMINATE
    };
    PIN_State extFlashPinState;
    PIN_Handle extFlashPinHandle = PIN_open(&extFlashPinState, extFlashPinTable);

    uint8_t extFlashShutdown = 0xB9;

    Board_sendExtFlashByte(extFlashPinHandle, extFlashShutdown);

    PIN_close(extFlashPinHandle);
}


#include <ti/drivers/Board.h>

/*
 *  ======== Board_initHook ========
 *  Perform any board-specific initialization needed at startup.  This
 *  function is declared weak to allow applications to override it if needed.
 */
void __attribute__((weak)) Board_initHook(void)
{
}

/*
 *  ======== Board_init ========
 *  Perform any initialization needed before using any board APIs
 */
void Board_init(void)
{
    /* ==== /ti/drivers/Power initialization ==== */
    Power_init();

    /* ==== /ti/devices/CCFGTemplate initialization ==== */

    /* ==== /ti/drivers/PIN initialization ==== */
    if (PIN_init(BoardGpioInitTable) != PIN_SUCCESS) {
        /* Error with PIN_init */
        while (1);
    }
    /* ==== /ti/drivers/RF initialization ==== */


    Board_shutDownExtFlash();

    Board_initHook();
}