U-Boot SPL 2016.05-00010-g9551b3d (Jul 18 2018 - 13:28:14) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v *** Warning - MMC init failed, using default environment Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... *** Warning - MMC init failed, using default environment reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05-00010-g9551b3d (Jul 18 2018 - 13:28:14 +0800) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x EVM REV DRAM: 1.5 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 ** First descriptor is NOT a primary desc on 1:1 ** Warning: fastboot.board_rev: unknown board revision GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** ERROR: cannot find partition: 'userdata' at arch/arm/cpu/armv7/omap-common/utils.c:199/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 ## Error: "board_findfdt" not defined switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 165 bytes read in 3 ms (53.7 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 3553296 bytes read in 265 ms (12.8 MiB/s) ** File not found /boot/dra7-evm-infoadas.dtb ** Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x363810 ] ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree ** First descriptor is NOT a primary desc on 1:1 ** switch to partitions #0, OK mmc1(part 0) is current device ** First descriptor is NOT a primary desc on 1:1 ** mmc - MMC sub system Usage: mmc info - display info of the current MMC device mmc read addr blk# cnt mmc write addr blk# cnt mmc erase blk# cnt mmc rescan mmc part - lists available partition on current mmc device mmc dev [dev] [part] - show or set current mmc device [partition] mmc list - lists available devices mmc hwpartition [args...] - does hardware partitioning arguments (sizes in 512-byte blocks): [user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes [gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition [check|set|complete] - mode, complete set partitioning completed WARNING: Partitioning is a write-once setting once it is set to complete. Power cycling is required to initialize partitions after set to complete. mmc bootbus dev boot_bus_width reset_boot_bus_width boot_mode - Set the BOOT_BUS_WIDTH field of the specified device mmc bootpart-resize - Change sizes of boot and RPMB partitions of specified device mmc partconf dev boot_ack boot_partition partition_access - Change the bits of the PARTITION_CONFIG field of the specified device mmc rst-function dev value - Change the RST_n_FUNCTION field of the specified device WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values. mmc setdsr - set DSR register value mmc - MMC sub system Usage: mmc info - display info of the current MMC device mmc read addr blk# cnt mmc write addr blk# cnt mmc erase blk# cnt mmc rescan mmc part - lists available partition on current mmc device mmc dev [dev] [part] - show or set current mmc device [partition] mmc list - lists available devices mmc hwpartition [args...] - does hardware partitioning arguments (sizes in 512-byte blocks): [user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes [gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition [check|set|complete] - mode, complete set partitioning completed WARNING: Partitioning is a write-once setting once it is set to complete. Power cycling is required to initialize partitions after set to complete. mmc bootbus dev boot_bus_width reset_boot_bus_width boot_mode - Set the BOOT_BUS_WIDTH field of the specified device mmc bootpart-resize - Change sizes of boot and RPMB partitions of specified device mmc partconf dev boot_ack boot_partition partition_access - Change the bits of the PARTITION_CONFIG field of the specified device mmc rst-function dev value - Change the RST_n_FUNCTION field of the specified device WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values. mmc setdsr - set DSR register value Booting from eMMC ... Wrong Image Format for bootm command ERROR: can't get kernel image! => boot ## Error: "board_findfdt" not defined ** First descriptor is NOT a primary desc on 1:1 ** switch to partitions #0, OK mmc1(part 0) is current device ** First descriptor is NOT a primary desc on 1:1 ** SD/MMC found on device 1 ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** First descriptor is NOT a primary desc on 1:1 ** switch to partitions #0, OK mmc1(part 0) is current device ** First descriptor is NOT a primary desc on 1:1 ** SD/MMC found on device 1 3553296 bytes read in 264 ms (12.8 MiB/s) 108307 bytes read in 51 ms (2 MiB/s) Booting from mmc1 ... Kernel image @ 0x82000000 [ 0x000000 - 0x363810 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe2000, end 8ffff712 ... OK Using machid 0xfe6 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.84-g742f84423d (tiiappadmin@swubn03) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Wed Jan 2 18:58:14 IST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB [ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x00000000be000000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0x00000000bfd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef631000 s14912 r8192 d21952 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258368 [ 0.000000] Kernel command line: console=ttyO0,115200n8 vram=16M root=PARTUUID=24f460fe-02 rw rootwait ip=none mem=1024M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 831020K/1040384K available (6615K kernel code, 319K rwdata, 2456K rodata, 340K init, 290K bss, 20948K reserved, 188416K cma-reserved, 233472K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08e402c (9073 kB) [ 0.000000] .init : 0xc08e5000 - 0xc093a000 ( 340 kB) [ 0.000000] .data : 0xc093a000 - 0xc0989ee0 ( 320 kB) [ 0.000000] .bss : 0xc098b000 - 0xc09d3800 ( 290 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000016] Switching to timer-based delay loop, resolution 162ns [ 0.000337] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000345] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000792] Console: colour dummy device 80x30 [ 0.000807] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000813] This ensures that you still see kernel messages. Please [ 0.000818] update your kernel commandline. [ 0.000831] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000845] pid_max: default: 32768 minimum: 301 [ 0.000944] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000955] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001503] Initializing cgroup subsys io [ 0.001520] Initializing cgroup subsys memory [ 0.001545] Initializing cgroup subsys devices [ 0.001557] Initializing cgroup subsys freezer [ 0.001568] Initializing cgroup subsys perf_event [ 0.001579] Initializing cgroup subsys pids [ 0.001606] CPU: Testing write buffer coherency: ok [ 0.001809] /cpus/cpu@0 missing clock-frequency property [ 0.001825] /cpus/cpu@1 missing clock-frequency property [ 0.001836] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001872] Setting up static identity map for 0x80008380 - 0x800083e0 [ 0.080062] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.080130] Brought up 2 CPUs [ 0.080143] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.080149] CPU: All CPU(s) started in HYP mode. [ 0.080155] CPU: Virtualization extensions available. [ 0.080535] devtmpfs: initialized [ 0.109464] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.110448] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.316249] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.316270] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.319893] pinctrl core: initialized pinctrl subsystem [ 0.320799] NET: Registered protocol family 16 [ 0.321728] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.350229] cpuidle: using governor ladder [ 0.380254] cpuidle: using governor menu [ 0.389044] OMAP GPIO hardware version 0.1 [ 0.393224] GPIO line 161 (radio_rst) hogged as output/low [ 0.395605] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@1400 ! [ 0.413218] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.413232] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.425264] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.425274] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.425741] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.425750] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.426336] OMAP DMA hardware revision 0.0 [ 0.471651] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.472879] edma 43300000.edma: memcpy is disabled [ 0.477634] edma 43300000.edma: TI EDMA DMA engine driver [ 0.482235] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.482413] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.482571] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.482727] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.483026] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.483218] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.486455] palmas 0-0058: IRQ missing: skipping irq request [ 0.500745] palmas 0-0058: Muxing GPIO 2e, PWM 0, LED 0 [ 0.573062] pcf857x 0-0020: probed [ 0.573638] pcf857x 0-0021: probed [ 0.573791] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.590784] GPIO line 463 (vin6_sel_s0) hogged as output/low [ 0.590882] pcf857x 1-0026: probed [ 0.591476] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 0.591853] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.610650] pcf857x: probe of 3-0021 failed with error -121 [ 0.610688] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 0.610909] media: Linux media interface: v0.10 [ 0.610959] Linux video capture interface: v2.00 [ 0.610999] pps_core: LinuxPPS API ver. 1 registered [ 0.611006] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.611032] PTP clock support registered [ 0.611077] EDAC MC: Ver: 3.0.0 [ 0.611855] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.612150] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.612519] Advanced Linux Sound Architecture Driver Initialized. [ 0.613354] clocksource: Switched to clocksource arch_sys_counter [ 0.623751] NET: Registered protocol family 2 [ 0.624247] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.624311] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.624436] TCP: Hash tables configured (established 8192 bind 8192) [ 0.624485] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.624516] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.624722] NET: Registered protocol family 1 [ 0.624967] RPC: Registered named UNIX socket transport module. [ 0.624975] RPC: Registered udp transport module. [ 0.624981] RPC: Registered tcp transport module. [ 0.624988] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.626019] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.636121] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.636771] NFS: Registering the id_resolver key type [ 0.636797] Key type id_resolver registered [ 0.636804] Key type id_legacy registered [ 0.636877] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.638171] bounce: pool size: 64 pages [ 0.638325] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.638339] io scheduler noop registered [ 0.638350] io scheduler deadline registered [ 0.638383] io scheduler cfq registered (default) [ 0.643315] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.646633] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges: [ 0.646646] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus 00-ff] [ 0.646679] IO 0x20003000..0x20012fff -> 0x00000000 [ 0.646699] MEM 0x20013000..0x2fffffff -> 0x20013000 [ 0.676851] dra7-pcie 51000000.pcie_rc: link is not up [ 0.677016] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00 [ 0.677029] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.677040] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.677050] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 0.677455] PCI: bus0: Fast back to back transfers disabled [ 0.677578] PCI: bus1: Fast back to back transfers enabled [ 0.677662] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.677677] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 0.677690] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.677912] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.738197] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.741555] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 301, base_baud = 3000000) is a 8250 [ 1.728662] console [ttyS0] enabled [ 1.733049] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 302, base_baud = 3000000) is a 8250 [ 1.742752] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 303, base_baud = 3000000) is a 8250 [ 1.752877] [drm] Initialized drm 1.1.0 20060810 [ 1.759619] OMAP DSS rev 6.1 [ 1.763405] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 1.771834] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 1.781732] connector-hdmi connector@1: failed to find video source [ 1.794443] loop: module loaded [ 1.798582] nand: No NAND device found [ 1.802353] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.812230] m25p80 spi32766.0: found w25q256, expected s25fl256s1 [ 1.818391] m25p80 spi32766.0: w25q256 (32768 Kbytes) [ 1.823536] 7 ofpart partitions found on MTD device spi32766.0 [ 1.829395] Creating 7 MTD partitions on "spi32766.0": [ 1.834572] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.840673] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.847036] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.854012] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.860700] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 1.868134] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 1.874485] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 1.882230] libphy: Fixed MDIO Bus: probed [ 1.933384] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 1.939509] davinci_mdio 48485000.mdio: detected phy mask fffffff3 [ 1.949685] libphy: 48485000.mdio: probed [ 1.953734] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown [ 1.961775] davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown [ 1.970500] cpsw 48484000.ethernet: Detected MACID = f0:b5:d1:16:51:9c [ 1.977159] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 1.984129] cpsw 48484000.ethernet: cpsw: Detected MACID = f0:b5:d1:16:51:9d [ 1.992807] mousedev: PS/2 mouse device common for all mice [ 1.999097] i2c /dev entries driver [ 2.003296] tvp5158 1-0058: Unable to of_probe [ 2.008124] ov1063x 1-0037: Failed writing register 0x0103! [ 2.013751] ov1063x: probe of 1-0037 failed with error -121 [ 2.020102] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin [ 2.027185] vip 48970000.vip: loading firmware vpdma-1b8.bin [ 2.037632] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.043259] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.049720] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.053382] vip 48970000.vip: VPDMA firmware loaded [ 2.056225] vpe 489d0000.vpe: Device registered as /dev/video0 [ 2.067111] evm_3v3_sw: supplied by sysen1 [ 2.146158] mmc0: MAN_BKOPS_EN bit is not set [ 2.157467] mmc0: new HS200 MMC card at address 0001 [ 2.162907] mmcblk0: mmc0:0001 R1J55A 7.28 GiB [ 2.167714] mmcblk0boot0: mmc0:0001 R1J55A partition 1 8.00 MiB [ 2.173888] mmcblk0boot1: mmc0:0001 R1J55A partition 2 8.00 MiB [ 2.225225] ledtrig-cpu: registered to indicate activity on CPUs [ 2.236419] hwspinlock_user gatemp: requested 20 hwspinlocks [ 2.243407] aic_dvdd: supplied by evm_3v3_sw [ 2.250174] davinci-mcasp 48464000.mcasp: DAI is shared [ 2.256303] davinci-mcasp 48474000.mcasp: DAI is shared [ 2.261753] davinci-mcasp 4847c000.mcasp: invalid tdm slots: 0 [ 2.268847] omap-hdmi-audio omap-hdmi-audio.0.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok [ 2.279725] NET: Registered protocol family 10 [ 2.295025] sit: IPv6 over IPv4 tunneling driver [ 2.300214] NET: Registered protocol family 17 [ 2.304964] Key type dns_resolver registered [ 2.309365] omap_voltage_late_init: Voltage driver support not added [ 2.316281] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.322491] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.329240] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.335479] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.343695] Power Management for TI OMAP4+ devices. [ 2.348803] Registering SWP/SWPB emulation handler [ 2.354588] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.361798] dmm 4e000000.dmm: initialized all PAT entries [ 2.369001] tvp5158 1-0058: Unable to of_probe [ 2.373948] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.414587] asoc-simple-card sound0: tlv320aic3x-hifi <-> 48468000.mcasp mapping ok [ 2.434763] asoc-simple-card jamr3_sound: tlv320aic3x-hifi <-> 48474000.mcasp mapping ok [ 2.466047] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.472690] [drm] No driver support for vblank timestamp query. [ 2.555430] omap_hsmmc 4809c000.mmc: card busy [ 2.685470] omap_hsmmc 4809c000.mmc: card busy [ 2.754498] [drm] Enabling DMM ywrap scrolling [ 2.790189] Console: switching to colour frame buffer device 240x67 [ 2.811326] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 2.819350] omap_hsmmc 4809c000.mmc: card busy [ 2.843818] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0 [ 2.850001] tvp5158 1-0058: Unable to of_probe [ 2.855508] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 2.862467] hctosys: unable to open rtc device (rtc0) [ 2.862541] tvp5158 1-0058: Unable to of_probe [ 2.882245] evm_1v8: disabling [ 2.885341] aic_dvdd: disabling [ 2.888494] vmmcwl_fixed: disabling [ 2.892180] ldousb: disabling [ 2.895632] ALSA device list: [ 2.898611] #0: DRA7xx-EVM [ 2.901499] #1: HDMI 58040000.encoder [ 2.905361] #2: DRA7xx-JAMR3 [ 2.909248] Waiting for root device PARTUUID=24f460fe-02... [ 2.935459] omap_hsmmc 4809c000.mmc: card busy [ 3.065460] omap_hsmmc 4809c000.mmc: card busy [ 3.195434] omap_hsmmc 4809c000.mmc: card busy [ 3.325535] omap_hsmmc 4809c000.mmc: card busy [ 3.455451] omap_hsmmc 4809c000.mmc: card busy [ 3.585451] omap_hsmmc 4809c000.mmc: card busy [ 3.715451] omap_hsmmc 4809c000.mmc: card busy [ 3.763366] mmc2: Skipping voltage switch [ 3.830498] mmc2: host does not support reading read-only switch, assuming write-enable [ 3.840470] mmc2: new high speed SDHC card at address 0007 [ 3.856483] mmcblk1: mmc2:0007 SD16G 14.5 GiB [ 3.862151] mmcblk1: p1 p2 [ 3.865735] tvp5158 1-0058: Unable to of_probe [ 3.904178] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities [ 3.913071] EXT4-fs (mmcblk1p2): couldn't mount as ext2 due to feature incompatibilities [ 3.960372] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.968544] VFS: Mounted root (ext4 filesystem) on device 179:50. [ 3.978956] devtmpfs: mounted [ 3.982142] Freeing unused kernel memory: 340K [ 3.986623] This architecture does not have kernel memory protection. [ 4.242132] systemd[1]: System time before build time, advancing clock. [ 4.282332] random: systemd: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 4.295484] random: systemd: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 4.307230] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 4.325778] systemd[1]: Detected architecture arm. Welcome to Arago 2016.12! [ 4.354679] systemd[1]: Set hostname to . [ 4.415410] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 25 bits of entropy available) [ 4.453197] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 26 bits of entropy available) [ 4.464527] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 26 bits of entropy available) [ 4.481575] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 27 bits of entropy available) [ 4.494854] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 27 bits of entropy available) [ 4.597439] random: systemd: uninitialized urandom read (16 bytes read, 30 bits of entropy available) [ 4.606960] random: systemd: uninitialized urandom read (16 bytes read, 30 bits of entropy available) [ 4.616852] random: systemd: uninitialized urandom read (16 bytes read, 30 bits of entropy available) [ 5.057244] systemd[1]: alignment.service: Found ordering cycle on alignment.service/start [ 5.065611] systemd[1]: alignment.service: Found dependency on sysinit.target/start [ 5.073307] systemd[1]: alignment.service: Found dependency on alignment.service/start [ 5.081346] systemd[1]: alignment.service: Breaking ordering cycle by deleting job alignment.service/start [ 5.091080] systemd[1]: alignment.service: Job alignment.service/start deleted to break ordering cycle starting with alignment.service/start [ SKIP ] Ordering cycle found, skipping alignment.service [ 5.125511] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 5.153758] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 5.198332] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 5.234793] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.263747] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 5.293653] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 5.313536] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 5.333615] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 5.363546] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 5.393543] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 5.413606] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 5.444098] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 5.474172] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 5.503553] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 5.524080] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 5.553649] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 5.613776] systemd[1]: Starting Journal Service... Starting Journal Service... [ 5.656209] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 5.694049] systemd[1]: Mounting Temporary Directory... [ 5.700267] CMEMK module: reference Linux version 4.4.84 [ 5.706777] no physical memory specified [ 5.710748] cmemk initialized Mounting Temporary Directory... [ 5.735761] systemd[1]: Mounting POSIX Message Queue File System... [ 5.742633] cryptodev: driver 1.8 loaded. Mounting POSIX Message Queue File System... [ 5.775875] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 5.805835] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 5.835719] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 5.852781] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) [ 5.865738] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 5.893954] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 5.947950] systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. [ 5.973694] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 5.993584] systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. [ 6.013779] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Setup Virtual Console. Starting udev Coldplug all Devices... Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ 6.653898] systemd-journald[127]: Received request to flush runtime journal from PID 1 Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ 7.003069] omap-rproc 58820000.ipu: assigned reserved memory node ipu1_cma@9d000000 [ 7.025803] remoteproc0: 58820000.ipu is available [ 7.030729] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 7.064862] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 7.076761] tvp5158 1-0058: Unable to of_probe [ 7.081803] remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 7.092530] omap-rproc 55020000.ipu: assigned reserved memory node ipu2_cma@95800000 [ 7.102131] remoteproc0: failed to load dra7-ipu1-fw.xem4 [ 7.107814] remoteproc1: 55020000.ipu is available [ 7.114290] remoteproc1: Note: remoteproc is still under development and considered experimental. [ 7.124574] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. Starting Load/Save Random Seed... [ 7.150172] tvp5158 1-0058: Unable to of_probe [ 7.157696] omap-rproc 40800000.dsp: assigned reserved memory node dsp1_cma@99000000 [ 7.182166] remoteproc2: 40800000.dsp is available [ 7.187332] remoteproc2: Note: remoteproc is still under development and considered experimental. [ OK ] Reached target Local File Systems. [ 7.212707] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 7.236415] remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 7.246209] tvp5158 1-0058: Unable to of_probe [ 7.252682] omap-rproc 41000000.dsp: assigned reserved memory node dsp2_cma@9f000000 [ 7.268839] remoteproc2: failed to load dra7-dsp1-fw.xe66 [ 7.279691] remoteproc3: 41000000.dsp is available [ 7.284681] remoteproc3: Note: remoteproc is still under development and considered experimental. [ 7.294602] remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. Starting Create Volatile Files and Directories... [ 7.317897] remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2 [ 7.329149] tvp5158 1-0058: Unable to of_probe [ 7.329756] remoteproc3: failed to load dra7-dsp2-fw.xe66 [ OK [ 7.412131] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20 ] Started Load/Save Random Seed.[ 7.424091] tvp5158 1-0058: Unable to of_probe [ OK ] Started Create Volatile Files and Directories. [ 7.442996] remoteproc1: registered virtio0 (type 7) [ 7.456358] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ OK ] Found device /dev/ttyS0. [ 7.526794] tvp5158 1-0058: Unable to of_probe [ 7.531693] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0 [ 7.548323] tvp5158 1-0058: Unable to of_probe [ 7.653846] SCSI subsystem initialized Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... [ 7.729808] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 7.752846] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 7.775572] CAN device driver interface [ 7.814194] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst [ OK ] Started Network Time Synchronization. [ 7.867112] scsi host0: ahci [ 7.870321] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 345 [ 7.899230] tvp5158 1-0058: Unable to of_probe [ 7.904564] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 7.914460] tvp5158 1-0058: Unable t of_probe [ OK ] Started Update UTMP about System Boot/Shutdown. [ 7.930073] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 Starting Synchronize System and HW clocks... [ 8.052277] tvp5158 1-0058: Unable to of_probe [ 8.057530] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ OK ] Reached target System Time Synchronized. [ 8.09851] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 8.098609] tvp5158 1-0058: Unable to of_probe [ 8.109472] tvp5158 1-0058: Unable to of_probe [ 8.116225] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=365) [ OK ] Started Synchronize System and HW clocks. [ 8.137850] tvp5158 1-0058: Unable to of_probe [ 8.178797] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1 [ 8.190128] tvp5158 1-0058: Unable to of_probe [ 8.228141] tvp5158 1-0058: Unable to of_probe [ 8.237494] ata1: SATA link down (SStatus 0 SControl 300) [ OK ] Reached target Sound Card. [ OK ] Reached target System Initialization. [ OK ] Listening on dropbear.socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. [ 8.783212] remoteproc1: powering up 55020000.ipu [ 8.812642] remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 3743164 [ 8.822921] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1 [ 8.882390] remoteproc1: remote processor 55020000.ipu is now up [ 8.889239] virtio_rpmsg_bus virtio0: rpmsg host is online [ 8.892395] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x65 [ 8.893278] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x66 [ 8.909895] tvp5158 1-0058: Unable to of_probe Starting Login Service... [ 8.940599] rpmsg_rpc rpmsg0: probing service dce-callback with src 1024 dst 101 [ 8.949916] tvp5158 1-0058: Unable to of_probe [ 8.954447] rpmsg_rpc rpmsg0: published functions = 4 [ 8.959714] rpmsg_rpc rpmsg1: probing service rpmsg-dce with src 1025 dst 102 [ 8.967588] tvp5158 1-0058: Unable to of_probe [ 8.967854] rpmsg_rpc rpmsg1: published functions = 9 Starting rc.pvr.service... [ 9.053174] tvp5158 1-0058: Unable to of_probe [ OK ] Started System Logging Service. Starting Save/Restore Sound Card State... [ 9.109947] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] Starting Permit User Sessions... Starting Network Service... [ OK ] Started Kernel Logging Service. [ OK ] Started rc.pvr.service. [ OK ] Started Save/Restore Sound Card State.[ 9.234540] net eth1: initializing cpsw version 1.15 (0) [ OK ] Started Permit User Sessions.[ 9.256580] net eth0: initialized cpsw ale version 1.4 [ 9.270118] net eth0: ALE Table size 1024 [ OK ] Started Network Service.[ 9.285115] tvp5158 1-0058: Unable to of_probe [ 9.294895] net eth1: phy found : id is : 0x20005c7a [ 9.316457] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 9.331714] net eth0: initializing cpsw version 1.15 (0) [ 9.337321] tvp5158 1-0058: Unable to of_probe [ 9.362154] tvp5158 1-0058: Unable to of_probe [ 9.380286] usbcore: registered new interface driver usbfs [ 9.390579] net eth0: phy found : id is : 0x20005c7a [ 9.402262] usbcore: registered new interface driver hub [ 9.420634] usbcore: registered new device driver usb [ 9.433402] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.460494] dwc3 48890000.usb: otg: primary host xhci-hcd.1.auto registered [ 9.468221] dwc3 48890000.usb: otg: shared host xhci-hcd.1.auto registered [ 9.477038] dwc3 48890000.usb: otg: can't start till gadget registers [ 9.484930] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 9.485066] tvp5158 1-0058: Unable to of_probe [ 9.496967] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1 [ 9.505873] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010 [ 9.515522] xhci-hcd xhci-hcd.2.auto: irq 511, io mem 0x488d0000 [ 9.522171] hub 1-0:1.0: USB hub found [ 9.527841] hub 1-0:1.0: 1 port detected [ 9.532100] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 9.532127] tvp5158 1-0058: Unable to of_probe [ 9.545343] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 9.553097] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 9.563180] hub 2-0:1.0: USB hub found [ 9.567956] hub 2-0:1.0: 1 port detected [ 9.572224] tvp5158 1-0058: Unable to of_probe [ 9.578195] tvp5158 1-0058: Unable to of_probe [ OK ] Started Login Service. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Network. Starting Network Name Resolution... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. Starting weston.service... [ OK ] Started Network Name Resolution. [ OK ] Started weston.service. Starting telnetd.service... Starting tiipclad-daemon.service... [ OK ] Started telnetd.service. [ OK ] Started tiipclad-daemon.service. [ 11.859928] random: nonblocking pool is initialized _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dra7xx-evm ttyS0 Arago 2016.12 dra7xx-evm ttyS0 dra7xx-evm login: root root@dra7xx-evm:~# reboot [ OK ] Stopped target System Time Synchronized. Stopping Network Time Synchronization... [ OK ] Stopped target Sound Card. [ OK ] Stopped target Multi-User System. Stopping Network Name Resolution... Starting Update UT Stopping Session c1 of user root. Stopping System Logging Service... [ OK ] Stopped target Login Prompts. [ OK ] Stopped Serial Getty on ttyO0. Stopping Kernel Logging Service... Unmounting /run/media/mmcblk1p1... [ OK ] Closed Load/Save RF Kill Switch Status /dev/rfkill Watch. Unmounting /run/user/0... Stopping telnetd.service... Stopping Getty on tty1... [ OK ] Stopped target Timers. [ OK ] Stopped Daily Cleanup of Temporary Directories. Stopping Serial Getty on ttyS0... Stopping tiipclad-daemon.service... Stopping Save/Restore Sound Card State... Stopping User Manager for UID 0... [ OK ] Stopped Network Time Synchronization. [ OK ] Stopped System Logging Service. [ OK ] Stopped Kernel Logging Service. [ OK ] Stopped Network Name Resolution. [ OK ] Stopped Getty on tty1. [ OK ] Stopped Serial Getty on ttyS0. [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Removed slice system-serial\x2dgetty.slice. [ OK ] Removed slice system-getty.slice. [ OK ] Stopped target Network. Stopping Network Service... [ OK ] Stopped Network Service. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Load Kernel Modules. Stopping D-Bus System Message Bus... [ OK ] Stopped D-Bus System Message Bus. [ OK ] Stopped Session c1 of user root. [ OK ] Unmounted /run/media/mmcblk1p1. [ OK ] Stopped User Manager for UID 0. [FAILED] Failed unmounting /run/user/0. [ OK ] Stopped telnetd.service. [ OK ] Stopped tiipclad-daemon.service. Stopping weston.service... [ OK ] Stopped target Local File Systems (Pre). [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Removed slice User Slice of root. Stopping Login Service... Stopping Permit User Sessions... [ OK ] Stopped Login Service. [ OK ] Stopped weston.service. [ OK ] Stopped Permit User Sessions. [ OK ] Stopped target Remote File Systems. Stopping rc.pvr.service... [ OK ] Stopped rc.pvr.service. [ OK ] Stopped Save/Restore Sound Card State. [ OK ] Stopped target Basic System. [ OK ] Stopped target Slices. [ OK ] Removed slice User and Session Slice. [ OK ] Stopped target Sockets. [ OK ] Closed D-Bus System Message Bus Socket. [ OK ] Closed dropbear.socket. [ OK ] Closed Syslog Socket. [ OK ] Stopped target Paths. [ OK ] Stopped Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Shutdown. Unmounting Temporary Directory... [FAILED] Failed unmounting Temporary Directory. [ OK ] Reached target Unmount All Filesystems. [ OK ] Reached target Final Step. Starting Reboot... [ 37.674824] watchdog watchdog0: watchdog did not stop! [ 38.181632] systemd-shutdown[1]: Sending SIGTERM to remaining processes... [ 38.205833] systemd-journald[127]: Received SIGTERM from PID 1 (systemd-shutdow). [ 38.346515] systemd-shutdown[1]: Sending SIGKILL to remaining processes... [ 38.370746] systemd-shutdown[1]: Hardware watchdog 'OMAP Watchdog', version 0 [ 38.379442] systemd-shutdown[1]: Unmounting file systems. [ 38.391524] systemd-shutdown[1]: Remounting '/run/user/0' read-only with options 'size=101980k,mode=700'. [ 38.401255] systemd-shutdown[1]: Unmounting /run/user/0. [ 38.433586] systemd-shutdown[1]: Remounting '/var/volatile' read-only with options 'size=51200k'. [ 38.442538] systemd-shutdown[1]: Unmounting /var/volatile. [ 38.473505] systemd-shutdown[1]: Remounting '/media/ram' read-only with options 'size=16384k'. [ 38.482202] systemd-shutdown[1]: Unmounting /media/ram. [ 38.513427] systemd-shutdown[1]: Remounting '/tmp' read-only with options ''. [ 38.520639] systemd-shutdown[1]: Unmounting /tmp. [ 38.563521] systemd-shutdown[1]: Remounting '/' read-only with options 'data=ordered'. [ 45.182324] EXT4-fs (mmcblk1p2): re-mounted. Opts: data=ordered [ 45.191222] systemd-shutdown[1]: Remounting '/' read-only with options 'data=ordered'. [ 45.199280] EXT4-fs (mmcblk1p2): re-mounted. Opts: data=ordered [ 45.205304] systemd-shutdown[1]: Remounting '/' read-only with options 'data=ordered'. [ 45.213291] EXT4-fs (mmcblk1p2): re-mounted. Opts: data=ordered [ 45.219361] systemd-shutdown[1]: All filesystems unmounted. [ 45.224984] systemd-shutdown[1]: Deactivating swaps. [ 45.230140] systemd-shutdown[1]: All swaps deactivated. [ 45.235448] systemd-shutdown[1]: Detaching loop devices. [ 45.247241] systemd-shutdown[1]: All loop devices detached. [ 45.252854] systemd-shutdown[1]: Detaching DM devices. [ 45.258375] systemd-shutdown[1]: All DM devices detached. [ 45.275941] systemd-shutdown[1]: Rebooting. [ 45.315620] reboot: Restarting system