U-Boot SPL 2016.05-g35dae4d-dirty (May 11 2018 - 18:44:12) DRA752-GP ES2.0 ti_i2c_eeprom_init failed 1 Bypassing DPLL failed 4a008180 MII 0 power strap setting(Pull low COL,CRS MII 0 power strap setting(Pull low COL,CRS U-Boot SPL 2016.05-g35dae4d-dirty (May 11 2018 - 18:44:12) DRA752-GP ES2.0 @SD max clock = 10000000@ !!!!!!!@SD max clock = 10000000@ MMC Device 1 not found *** Warning - No MMC card found, using default environment Trying to boot from MMC1 MMC Device 1 not found *** Warning - No MMC card found, using default environment reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05-g35dae4d-dirty (May 11 2018 - 18:44:12 +0800) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x EVM REV DRAM: 3 GiB NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1, OMAP SD/MMC: 2 @eMMC max clock = 26000000@ *** Warning - bad CRC, using default environment Warning: fastboot.board_rev: unknown board revision GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** ERROR: cannot find partition: 'userdata' at arch/arm/cpu/armv7/omap-common/utils.c:195/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: Target spinup took 0 ms. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: 8GB SATA Flash D Rev: SFPS Type: Hard Disk Capacity: 7641.2 MB = 7.4 GB (15649200 x 512) Found 1 device(s). Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 load MAN2020_original.dtb load MAN2020_3g switch to partitions #0, OK mmc0 is current device @SD max clock = 10000000@ !!!!!!!@SD max clock = 10000000@ SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 222 bytes read in 3 ms (72.3 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... @SD max clock = 10000000@ !!!!!!!@SD max clock = 10000000@ switch to partitions #0, OK mmc0 is current device @SD max clock = 10000000@ !!!!!!!@SD max clock = 10000000@ SD/MMC found on device 0 3636216 bytes read in 781 ms (4.4 MiB/s) 111458 bytes read in 77 ms (1.4 MiB/s) Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x377bf8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe1000, end 8ffff361 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.45-g29f1bae-dirty (hsuyz@hsuyz-VirtualBox) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #44 SMP PREEMPT Fri May 11 18:44:48 CST 2018 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 [ 0.000000] cma: Reserved 64 MiB at 0x00000000fb000000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @ec076000 s14848 r8192 d22016 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 780096 [ 0.000000] Kernel command line: console=ttyO3,115200n8 elevator=noop root=/dev/mmcblk0p2 rw rootwait earlyprintk fixrtc omapdrm.num_crtc=2 consoleblank=0 cma=64M rootfstype=ext4 snd.slots_reserved=1,1 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 3022672K/3127296K available (6635K kernel code, 364K rwdata, 2472K rodata, 336K init, 302K bss, 39088K reserved, 65536K cma-reserved, 2275328K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08ed09c (9109 kB) [ 0.000000] .init : 0xc08ee000 - 0xc0942000 ( 336 kB) [ 0.000000] .data : 0xc0942000 - 0xc099d1d0 ( 365 kB) [ 0.000000] .bss : 0xc099f000 - 0xc09eaa78 ( 303 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div [ 0.000000] OMAP clockevent source: timer1 at 31475 Hz [ 0.000000] Architected cp15 timer(s) running at 5.90MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x15c70fb29, max_idle_ns: 440795202138 ns [ 0.000005] sched_clock: 56 bits at 5MHz, resolution 169ns, wraps every 4398046511093ns [ 0.000015] Switching to timer-based delay loop, resolution 169ns [ 0.000370] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000379] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000836] Console: colour dummy device 80x30 [ 0.000853] WARNING: Your 'console=ttyO3' has been replaced by 'ttyS3' [ 0.000860] This ensures that you still see kernel messages. Please [ 0.000866] update your kernel commandline. [ 0.000880] Calibrating delay loop (skipped), value calculated using timer frequency.. 11.80 BogoMIPS (lpj=59016) [ 0.000892] pid_max: default: 32768 minimum: 301 [ 0.000983] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000993] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001528] Initializing cgroup subsys io [ 0.001546] Initializing cgroup subsys memory [ 0.001570] Initializing cgroup subsys devices [ 0.001582] Initializing cgroup subsys freezer [ 0.001593] Initializing cgroup subsys perf_event [ 0.001604] Initializing cgroup subsys pids [ 0.001631] CPU: Testing write buffer coherency: ok [ 0.001832] /cpus/cpu@0 missing clock-frequency property [ 0.001849] /cpus/cpu@1 missing clock-frequency property [ 0.001859] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001894] Setting up static identity map for 0x800082c0 - 0x80008320 [ 0.080174] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.080233] Brought up 2 CPUs [ 0.080246] SMP: Total of 2 processors activated (23.60 BogoMIPS). [ 0.080252] CPU: All CPU(s) started in HYP mode. [ 0.080258] CPU: Virtualization extensions available. [ 0.080628] devtmpfs: initialized [ 0.110119] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.111120] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.305908] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.307433] pinctrl core: initialized pinctrl subsystem [ 0.308258] NET: Registered protocol family 16 [ 0.309220] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.330225] cpuidle: using governor ladder [ 0.360250] cpuidle: using governor menu [ 0.368529] OMAP GPIO hardware version 0.1 [ 0.372613] GPIO line 161 (radio_rst) hogged as output/low [ 0.374949] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@1400 ! [ 0.391748] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.391761] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.400344] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.400354] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.401154] OMAP DMA hardware revision 0.0 [ 0.441565] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.442708] edma 43300000.edma: memcpy is disabled [ 0.447527] edma 43300000.edma: TI EDMA DMA engine driver [ 0.454392] palmas 0-0058: IRQ missing: skipping irq request [ 0.471222] palmas 0-0058: Muxing GPIO a, PWM 0, LED 0 [ 0.471341] @@@@1 [ 0.471551] @@@@3 [ 0.471559] @@@@4 [ 0.471568] @@@@5 [ 0.471922] @@@@6 [ 0.472085] @@@@7 [ 0.480771] @@@@8 [ 0.542886] @@@@9(0) [ 0.542904] @@@@2 [ 0.542935] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.543350] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 0.543715] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.544072] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 0.544434] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 0.544623] media: Linux media interface: v0.10 [ 0.544677] Linux video capture interface: v2.00 [ 0.544720] pps_core: LinuxPPS API ver. 1 registered [ 0.544727] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.544750] PTP clock support registered [ 0.544796] EDAC MC: Ver: 3.0.0 [ 0.545559] Advanced Linux Sound Architecture Driver Initialized. [ 0.546425] clocksource: Switched to clocksource arch_sys_counter [ 0.557073] NET: Registered protocol family 2 [ 0.557572] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.557636] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.557761] TCP: Hash tables configured (established 8192 bind 8192) [ 0.557809] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.557840] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.558044] NET: Registered protocol family 1 [ 0.558304] RPC: Registered named UNIX socket transport module. [ 0.558313] RPC: Registered udp transport module. [ 0.558320] RPC: Registered tcp transport module. [ 0.558326] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.559354] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.561981] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.569676] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.570315] NFS: Registering the id_resolver key type [ 0.570348] Key type id_resolver registered [ 0.570356] Key type id_legacy registered [ 0.570408] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.572337] bounce: pool size: 64 pages [ 0.572495] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.572511] io scheduler noop registered (default) [ 0.572522] io scheduler deadline registered [ 0.572555] io scheduler cfq registered [ 0.577831] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.640761] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.644153] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 299, base_baud = 3000000) is a 8250 [ 0.645031] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 300, base_baud = 3000000) is a 8250 [ 0.645895] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250 [ 0.646775] console [ttyS3] disabled [ 0.646819] 4806e000.serial: ttyS3 at MMIO 0x4806e000 (irq = 302, base_baud = 3000000) is a 8250 [ 1.448059] console [ttyS3] enabled [ 1.452414] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 303, base_baud = 3000000) is a 8250 [ 1.462076] 48422000.serial: ttyS7 at MMIO 0x48422000 (irq = 304, base_baud = 3000000) is a 8250 [ 1.471739] 48424000.serial: ttyS8 at MMIO 0x48424000 (irq = 305, base_baud = 3000000) is a 8250 [ 1.481395] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 306, base_baud = 3000000) is a 8250 [ 1.491456] [drm] Initialized drm 1.1.0 20060810 [ 1.503227] loop: module loaded [ 1.507241] nand: No NAND device found [ 1.511012] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.523462] m25p80 spi32766.0: s25fl256s1 (32768 Kbytes) [ 1.528887] 7 ofpart partitions found on MTD device spi32766.0 [ 1.534748] Creating 7 MTD partitions on "spi32766.0": [ 1.539928] 0x000000000000-0x000000040000 : "QSPI.MLO" [ 1.545981] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.552287] 0x000000140000-0x0000001c0000 : "QSPI.DRA7-evm.dtb" [ 1.559113] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.565739] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 1.573096] 0x0000001e0000-0x0000009e0000 : "QSPI.uImage" [ 1.579408] 0x0000009e0000-0x000002000000 : "QSPI.IPU-exe" [ 1.586790] libphy: Fixed MDIO Bus: probed [ 1.591458] CAN device driver interface [ 1.595683] pinctrl-single 4a003400.pinmux: pin 4a003818.0 already requested by 4a003400.pinmux; cannot claim for 4ae3c000.can [ 1.607149] pinctrl-single 4a003400.pinmux: pin-262 (4ae3c000.can) status -22 [ 1.614322] pinctrl-single 4a003400.pinmux: could not request pin 262 (4a003818.0) from group dcan1_pins_sleep on device pinctrl-single [ 1.626651] c_can_platform 4ae3c000.can: Error applying setting, reverse things back [ 1.635073] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=357) [ 1.686459] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 1.692583] davinci_mdio 48485000.mdio: detected phy mask 0 [ 1.796429] davinci_mdio 48485000.mdio: timed out waiting for user access [ 1.896427] davinci_mdio 48485000.mdio: timed out waiting for idle [ 1.902654] davinci_mdio: probe of 48485000.mdio failed with error -5 [ 1.909768] cpsw 48484000.ethernet: Detected MACID = f0:45:da:8b:6a:62 [ 1.916442] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 1.923382] cpsw 48484000.ethernet: cpsw: Detected MACID = f0:45:da:8b:6a:63 [ 1.932028] mousedev: PS/2 mouse device common for all mice [ 1.938282] i2c /dev entries driver [ 1.943256] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin [ 1.953642] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 1.966610] vpe 489d0000.vpe: Device registered as /dev/video0 [ 2.006974] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.013362] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.036659] evm_3v3_sw: supplied by sysen1 [ 2.077918] ldo1: Restricting voltage, 3300000-1800000uV [ 2.083260] omap_hsmmc 480ad000.mmc: vmmc_aux set voltage failed [ 2.096437] omap_hsmmc 480ad000.mmc: failed to switch 1.8v [ 2.167200] ledtrig-cpu: registered to indicate activity on CPUs [ 2.177406] hwspinlock_user gatemp: requested 10 hwspinlocks [ 2.183775] [ 2.183775] [spidrv_init] [ 2.187906] spidrv_init called [ 2.190979] [ 2.190979] [mcaspdrv_init] [ 2.195270] mcaspdrv_init called [ 2.199588] davinci-mcasp 48460000.mcasp: DAI is shared [ 2.204862] [ 2.204862] [McASP1][mcasp->base][FA460000] [ 2.210658] davinci-mcasp 48464000.mcasp: DAI is shared [ 2.215923] [ 2.215923] [McASP2][mcasp->base][FA464000] [ 2.215923] [ 2.223208] davinci-mcasp 48468000.mcasp: DAI is shared [ 2.228484] [ 2.228484] [McASP3][mcasp->base][FA468000] [ 2.228484] [ 2.236752] NET: Registered protocol family 10 [ 2.252086] sit: IPv6 over IPv4 tunneling driver [ 2.257281] NET: Registered protocol family 17 [ 2.261761] can: controller area network core (rev 20120528 abi 9) [ 2.268082] NET: Registered protocol family 29 [ 2.272564] can: raw protocol (rev 20120528) [ 2.277063] Key type dns_resolver registered [ 2.281502] omap_voltage_late_init: Voltage driver support not added [ 2.288507] Power Management for TI OMAP4+ devices. [ 2.293648] Registering SWP/SWPB emulation handler [ 2.301176] dmm 4e000000.dmm: initialized all PAT entries [ 2.317714] hctosys: unable to open rtc device (rtc0) [ 2.334891] aic_dvdd: disabling [ 2.338074] vmmcwl_fixed: disabling [ 2.341771] ldousb: disabling [ 2.345246] ALSA device list: [ 2.348255] No soundcards found. [ 2.352461] Waiting for root device /dev/mmcblk0p2... [ 2.363516] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.373576] @SD max clock = 10000000@ [ 2.377375] mmc0: new high speed SDHC card at address 59b4 [ 2.383359] mmcblk0: mmc0:59b4 SD 14.7 GiB [ 2.389615] mmcblk0: p1 p2 [ 2.430226] mmc1: MAN_BKOPS_EN bit is not set [ 2.435572] @eMMC max clock = 25000000@ [ 2.439608] mmc1: new MMC card at address 0001 [ 2.454516] mmcblk1: mmc1:0001 MMC04G 3.57 GiB [ 2.469341] mmcblk1boot0: mmc1:0001 MMC04G partition 1 8.00 MiB [ 2.485520] mmcblk1boot1: mmc1:0001 MMC04G partition 2 8.00 MiB [ 2.493505] mmcblk1: p1 p2 [ 2.655411] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.663588] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.670993] devtmpfs: mounted [ 2.674178] Freeing unused kernel memory: 336K (c08ee000 - c0942000) [ 2.680576] This architecture does not have kernel memory protection. [ 3.669902] systemd[1]: System time before build time, advancing clock. [ 3.828334] random: systemd: uninitialized urandom read (16 bytes read, 12 bits of entropy available) [ 3.845058] random: systemd: uninitialized urandom read (16 bytes read, 12 bits of entropy available) [ 3.856853] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 3.875372] systemd[1]: Detected architecture arm. Welcome to Arago 2016.12! [ 3.908046] systemd[1]: Set hostname to . [ 4.078450] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 13 bits of entropy available) [ 4.126026] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 13 bits of entropy available) [ 4.136245] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 13 bits of entropy available) [ 4.167281] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 14 bits of entropy available) [ 4.188882] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 14 bits of entropy available) [ 4.485088] random: systemd: uninitialized urandom read (16 bytes read, 17 bits of entropy available) [ 4.494632] random: systemd: uninitialized urandom read (16 bytes read, 17 bits of entropy available) [ 4.504609] random: systemd: uninitialized urandom read (16 bytes read, 17 bits of entropy available) [ 4.652676] systemd[1]: Configuration file /etc/systemd/system/multi-user.target.wants/MAN2020.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 4.669309] systemd[1]: Configuration file /etc/systemd/system/multi-user.target.wants/MAN2020.service is marked world-writable. Please remove world writability permission bits. Proceeding anyway. [ 4.689344] systemd[1]: gplv3-notice.service: Service lacks both ExecStart= and ExecStop= setting. Refusing. [ 4.859687] systemd[1]: gplv3-notice.service: Cannot add dependency job, ignoring: Unit gplv3-notice.service is not loaded properly: Invalid argument. [ 4.874157] systemd[1]: sysinit.target: Found ordering cycle on sysinit.target/start [ 4.881976] systemd[1]: sysinit.target: Found dependency on alignment.service/start [ 4.889695] systemd[1]: sysinit.target: Found dependency on basic.target/start [ 4.896995] systemd[1]: sysinit.target: Found dependency on sysinit.target/start [ 4.904431] systemd[1]: sysinit.target: Breaking ordering cycle by deleting job alignment.service/start [ 4.913892] systemd[1]: alignment.service: Job alignment.service/start deleted to break ordering cycle starting with sysinit.target/start [ SKIP ] Ordering cycle found, skipping alignment.service [ 4.949419] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 4.976729] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 5.008125] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.036623] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 5.056594] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 5.086710] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 5.116766] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 5.210742] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 5.236658] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 5.266648] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 5.287290] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 5.316631] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 5.336761] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 5.366589] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 5.386711] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 5.436902] systemd[1]: Starting Journal Service... Starting Journal Service... [ 5.536692] systemd[1]: Mounting Temporary Directory... Mounting Temporary Directory... [ 5.559054] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 5.589146] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 5.686883] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 5.719139] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 5.749237] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 5.779459] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 5.793305] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Starting Create list of required st... nodes for the current kernel... [ 5.827469] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 5.891674] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 5.916696] systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. [ 5.936647] systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. [ 5.956905] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Setup Virtual Console. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create list of required sta...ce nodes for the current kernel. Starting Create Static Device Nodes in /dev... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [ 6.745733] systemd-journald[91]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Load/Save Random Seed... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started udev Kernel Device Manager. Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. Starting Synchronize System and HW clocks... [ OK ] Found device /dev/ttyS3. [ 7.970645] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20 [FAILED] Failed to start Synchronize System and HW clocks. See 'systemctl status sync-clocks.service' for details. [ OK ] Reached target System Initialization. [ 8.090329] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ OK ] Listening on dropbear.socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ 8.127777] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100 [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket.[ 8.171633] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100 [ OK ] Reached target Sockets. [ 8.206616] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100 [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. [ 8.288734] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc0 Starting Permit User Sessions... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started System Logging Service. [ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf. Starting Login Service... [ 8.567102] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec Starting uim-sysfs.service... [ OK ] Started Kernel Logging Service. Starting hw-id.service... [ 8.638314] SCSI subsystem initialized [ OK ] Started D-Bus System Message Bus. [ 8.687901] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 9.765544] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ 9.890105] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 9.919024] [drm] Initialized pvr 1.14.3699939 20110701 on minor 0 [ 9.962194] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 9.994561] ahci 4a140000.sata: Enable 32-bit DMA instead of 64-bit. [ 10.047468] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 10.149719] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 10.211770] NET: Registered protocol family 15 [ 10.219142] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 10.231330] scsi host0: ahci [ 10.234633] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 339 Starting Network Service... Starting Telephony service... [ OK ] Started Start helloworld. [ OK ] Started Permit User Sessions. [ OK ] Started hw-id.service. [INFO] VERSION: B0.3.0.0021 [SYS ] paring option: token=3, option=(null) [INFO] R3 init, iface=/dev/ttyS7 [INFO] R2 init [INFO] watchdog init [INFO] CLIENT ready [ 10.650784] Initializing XFRM netlink socket [ OK ] Started Network Service. [ 10.667476] net eth1: initializing cpsw version 1.15 (0) [ 10.674158] net eth0: initialized cpsw ale version 1.4 [ 10.701525] net eth0: ALE Table size 1024 [ 10.728603] libphy: PHY 48485000.mdio:03 not found [ 10.733428] net eth1: phy "48485000.mdio:03" not found on slave 1, err -19 [ 10.826465] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 10.876931] ata1.00: ATA-10: 8GB SATA Flash Drive, SFPS925A, max UDMA/133 [ 10.902708] net eth0: initializing cpsw version 1.15 (0) [ 10.909812] ata1.00: 15649200 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 10.942494] libphy: PHY 48485000.mdio:00 not found [ 10.953549] ata1.00: configured for UDMA/133 [ 10.970545] net eth0: phy "48485000.mdio:00" not found on slave 0, err -19 [ 11.022062] scsi 0:0:0:0: Direct-Access ATA 8GB SATA Flash D 925A PQ: 0 ANSI: 5 [ 11.106385] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 11.185118] EXT4-fs (mmcblk1p2): recovery complete [ 11.191752] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 11.274776] Bluetooth: Core ver 2.21 [ 11.298384] NET: Registered protocol family 31 [ 11.302860] Bluetooth: HCI device and connection manager initialized [ 11.357961] Bluetooth: HCI socket layer initialized [ 11.362879] Bluetooth: L2CAP socket layer initialized [ 11.416499] Bluetooth: SCO socket layer initialized [ 11.614092] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 11.625089] sd 0:0:0:0: [sda] Write Protect is off [ 11.636603] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.661387] sda: sda1 [ 11.669449] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.738997] @@USB2PHY_TERMINATION_CONTROL=0x220004 [ OK ] Started uim-sysfs.service. [ 12.279972] @@USB2PHY_TERMINATION_CONTROL=0x220004 [ 12.318552] EXT4-fs (sda1): recovery complete [ 12.322946] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Started Telephony service. Starting rc.pvr.service... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Network. Starting Network Name Resolution... Starting Lightning Fast Webserver With Light System Requirements... [ OK ] Started Serial Getty on ttyS3. [ OK ] Reached target Login Prompts. [ OK ] Started Login Service. [ 12.991419] usbcore: registered new interface driver usbfs [ 13.008486] usbcore: registered new interface driver hub [ 13.026580] usbcore: registered new device driver usb [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ 13.229069] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 13.234609] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 13.258303] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010 [ 13.273908] xhci-hcd xhci-hcd.0.auto: irq 431, io mem 0x48890000 [ 13.289989] hub 1-0:1.0: USB hub found [ 13.294038] hub 1-0:1.0: 1 port detected [ 13.304434] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ OK ] Started Network Name Resolution. [ 13.316481] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 13.336818] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 13.358316] hub 2-0:1.0: USB hub found [ 13.365825] hub 2-0:1.0: 1 port detected [ 13.378434] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 13.383966] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 13.416779] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00210010 [ 13.426028] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] [ 13.437009] xhci-hcd xhci-hcd.1.auto: irq 432, io mem 0x488d0000 [ 13.455777] hub 3-0:1.0: USB hub found [ 13.466555] hub 3-0:1.0: 1 port detected [ 13.473465] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 13.486495] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 13.506621] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 13.528786] hub 4-0:1.0: USB hub found [ 13.532593] hub 4-0:1.0: 1 port detected [ OK ] Started rc.pvr.service. Starting weston.service... [ OK ] Started weston.service. Starting telnetd.service... Starting tiipclad-daemon.service... [ OK ] Started telnetd.service. [ OK ] Started tiipclad-daemon.service. Starting thttpd.service... [ OK ] Started thttpd.service. Starting rng-tools.service... [ OK ] Started rng-tools.service. [ 14.240457] random: nonblocking pool is initialized Starting gdbserverproxy.service... [ OK ] Started gdbserverproxy.service. Starting matrix-gui-2.0.service... [ OK ] Started matrix-gui-2.0.service. Starting thermal-zone-init.service... [ OK ] Started thermal-zone-init.service. [ OK ] Reached target Multi-User System. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dra7xx-evm ttyS3 Arago 2016.12 dra7xx-evm ttyS3 dra7xx-evm login: root (automatic login) root@dra7xx-evm:~#