U-Boot SPL 2020.01 (Jul 28 2021 - 09:13:29 +0800) SYSFW ABI: 3.1 (firmware rev 0x0015 '21.5.0--v2021.05 (Terrific Llam') Reading on-board EEPROM at 0x50 failed 1 Trying to boot from MMC2 Starting ATF on ARM64 core... NOTICE: BL31: v2.3():07.01.00.004-1-g52c334fc3-dirty NOTICE: BL31: Built : 04:16:36, Nov 26 2020 U-Boot SPL 2020.01 (Jul 28 2021 - 09:12:13 +0800) SYSFW ABI: 3.1 (firmware rev 0x0015 '21.5.0--v2021.05 (Terrific Llam') Reading on-board EEPROM at 0x50 failed 1 Trying to boot from MMC2 U-Boot 2020.01 (Jul 28 2021 - 09:12:13 +0800) SoC: AM65X SR2.0 Model: Texas Instruments AM654 Base Board Reading on-board EEPROM at 0x50 failed 1 Board: AM6-COMPROCEVM rev E3 DRAM: 1 GiB MMC: sdhci@4f80000: 0, sdhci@4fa0000: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Reading on-board EEPROM at 0x50 failed 1 led_gpio_control error led value=1 Net: eth0: ethernet@46000000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device SD/MMC found on device 1 13797384 bytes read in 582 ms (22.6 MiB/s) 65658 bytes read in 10 ms (6.3 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 000000008feec000, end 000000008fffffff ... OK Starting kernel ... [ 0.000000] 000: printk: bootconsole [ns16550a0] enabled [ 0.000000] 000: Reserved memory: created DMA memory pool at 0x00000000a0000000, size 1 MiB [ 0.000000] 000: OF: reserved mem: initialized node r5f-dma-memory@a0000000, compatible id shared-dma-pool [ 0.000000] 000: Reserved memory: created DMA memory pool at 0x00000000a0100000, size 15 MiB [ 0.000000] 000: OF: reserved mem: initialized node r5f-memory@a0100000, compatible id shared-dma-pool [ 0.000000] 000: Reserved memory: created DMA memory pool at 0x00000000a1000000, size 1 MiB [ 0.000000] 000: OF: reserved mem: initialized node r5f-dma-memory@a1000000, compatible id shared-dma-pool [ 0.000000] 000: Reserved memory: created DMA memory pool at 0x00000000a1100000, size 15 MiB [ 0.000000] 000: OF: reserved mem: initialized node r5f-memory@a1100000, compatible id shared-dma-pool [ 0.000000] 000: cma: Reserved 24 MiB at 0x00000000be800000 [ 0.000000] 000: On node 0 totalpages: 110080 [ 0.000000] 000: DMA zone: 4096 pages used for memmap [ 0.000000] 000: DMA zone: 0 pages reserved [ 0.000000] 000: DMA zone: 247296 pages, LIFO batch:63 [ 0.000000] 000: DMA32 zone: 18446744073709414400 pages, LIFO batch:63 [ 0.000000] 000: psci: probing for conduit method from DT. [ 0.000000] 000: psci: PSCIv1.1 detected in firmware. [ 0.000000] 000: psci: Using standard PSCI v0.2 function IDs [ 0.000000] 000: psci: Trusted OS migration not required [ 0.000000] 000: psci: SMC Calling Convention v1.0 [ 0.000000] 000: percpu: Embedded 17 pages/cpu s32576 r8192 d28864 u69632 [ 0.000000] 000: pcpu-alloc: s32576 r8192 d28864 u69632 alloc=17*4096 [ 0.000000] 000: [ 0.000000] 000: pcpu-alloc: [ 0.000000] 000: [0] [ 0.000000] 000: 0 [ 0.000000] 000: [0] [ 0.000000] 000: 1 [ 0.000000] 000: [0] [ 0.000000] 000: 2 [ 0.000000] 000: [0] [ 0.000000] 000: 3 [ 0.000000] 000: [ 0.000000] 000: Detected VIPT I-cache on CPU0 [ 0.000000] 000: CPU features: detected: ARM erratum 845719 [ 0.000000] 000: CPU features: detected: GIC system register CPU interface [ 0.000000] 000: Built 1 zonelists, mobility grouping on. Total pages: 105984 [ 0.000000] 000: Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 isolcpus=1-3 mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),57216k@8m(ospi.rootfs),128k(ospi.phypattern) root=PARTUUID=0895eef8-02 rw rootfstype=ext4 rootwait [ 0.000000] 000: Dentry cache hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.000000] 000: Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] 000: mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] 000: Memory: 930476K/440320K available (8382K kernel code, 610K rwdata, 3084K rodata, 1344K init, 415K bss, 18446744073709036884K reserved, 24576K cma-reserved) [ 0.000000] 000: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] 000: rcu: Preemptible hierarchical RCU implementation. [ 0.000000] 000: rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] 000: rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] 000: rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] 000: No expedited grace period (rcu_normal_after_boot). [ 0.000000] 000: Tasks RCU enabled. [ 0.000000] 000: rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] 000: rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] 000: NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] 000: GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] 000: GICv3: 960 SPIs implemented [ 0.000000] 000: GICv3: 0 Extended SPIs implemented [ 0.000000] 000: GICv3: Distributor has no Range Selector support [ 0.000000] 000: GICv3: 16 PPIs implemented [ 0.000000] 000: GICv3: no VLPI support, no direct LPI support [ 0.000000] 000: GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000 [ 0.000000] 000: ITS [mem 0x01820000-0x0182ffff] [ 0.000000] 000: GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS [ 0.000000] 000: ITS@0x0000000001820000: Devices Table too large, reduce ids 20->19 [ 0.000000] 000: ITS@0x0000000001820000: allocated 524288 Devices @bc400000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] 000: ITS: using cache flushing for cmd queue [ 0.000000] 000: GICv3: using LPI property table @0x00000000bcc30000 [ 0.000000] 000: GIC: using cache flushing for LPI property table [ 0.000000] 000: GICv3: CPU0: using allocated LPI pending table @0x00000000bcc40000 [ 0.000000] 000: random: get_random_bytes called from start_kernel+0x2bc/0x440 with crng_init=0 [ 0.000000] 000: arch_timer: cp15 timer(s) running at 200.00MHz (phys). [ 0.000000] 000: clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns [ 0.000001] 000: sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns [ 0.008982] 000: Console: colour dummy device 80x25 [ 0.014021] 000: Calibrating delay loop (skipped), value calculated using timer frequency.. [ 0.022656] 000: 400.00 BogoMIPS (lpj=800000) [ 0.027115] 000: pid_max: default: 32768 minimum: 301 [ 0.032388] 000: LSM: Security Framework initializing [ 0.037621] 000: Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.045549] 000: Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.055519] 000: ASID allocator initialised with 32768 entries [ 0.061604] 000: rcu: Hierarchical SRCU implementation. [ 0.067449] 000: Platform MSI: gic-its@1820000 domain created [ 0.073556] 000: PCI/MSI: /bus@100000/interrupt-controller@1800000/gic-its@1820000 domain created [ 0.083004] 000: smp: Bringing up secondary CPUs ... [ 0.089250] 001: Detected VIPT I-cache on CPU1 [ 0.093830] 001: GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000 [ 0.101315] 001: GICv3: CPU1: using allocated LPI pending table @0x00000000bcc50000 [ 0.109180] 001: CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.117626] 002: Detected VIPT I-cache on CPU2 [ 0.122219] 002: GICv3: CPU2: found redistributor 100 region 0:0x00000000018c0000 [ 0.129892] 002: GICv3: CPU2: using allocated LPI pending table @0x00000000bcc60000 [ 0.137773] 002: CPU2: Booted secondary processor 0x0000000100 [0x410fd034] [ 0.146161] 003: Detected VIPT I-cache on CPU3 [ 0.150731] 003: GICv3: CPU3: found redistributor 101 region 0:0x00000000018e0000 [ 0.158400] 003: GICv3: CPU3: using allocated LPI pending table @0x00000000bcc70000 [ 0.166261] 003: CPU3: Booted secondary processor 0x0000000101 [0x410fd034] [ 0.173518] 000: smp: Brought up 1 node, 4 CPUs [ 0.178181] 000: SMP: Total of 4 processors activated. [ 0.183456] 000: CPU features: detected: 32-bit EL0 Support [ 0.189179] 000: CPU features: detected: CRC32 instructions [ 0.204230] 000: CPU: All CPU(s) started at EL2 [ 0.208914] 000: alternatives: patching kernel code [ 0.214863] 000: devtmpfs: initialized [ 0.228757] 000: clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.239231] 000: futex hash table entries: 1024 (order: 5, 131072 bytes, linear) [ 0.247875] 000: pinctrl core: initialized pinctrl subsystem [ 0.254590] 000: NET: Registered protocol family 16 [ 0.261499] 000: DMA: preallocated 256 KiB pool for atomic allocations [ 0.268909] 000: hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.295505] 000: HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.302860] 000: HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.310200] 000: HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.317537] 000: HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.326225] 000: cryptd: max_cpu_qlen set to 1000 [ 0.336216] 000: iommu: Default domain type: Translated [ 0.342064] 000: SCSI subsystem initialized [ 0.347039] 000: pps_core: LinuxPPS API ver. 1 registered [ 0.352919] 000: pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.362754] 000: PTP clock support registered [ 0.367254] 000: EDAC MC: Ver: 3.0.0 [ 0.372013] 000: FPGA manager framework [ 0.376847] 000: clocksource: Switched to clocksource arch_sys_counter [ 0.383841] 000: VFS: Disk quotas dquot_6.6.0 [ 0.388385] 000: VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.402011] 000: thermal_sys: Registered thermal governor 'step_wise' [ 0.408629] 000: thermal_sys: Registered thermal governor 'power_allocator' [ 0.416270] 000: NET: Registered protocol family 2 [ 0.421929] 000: tcp_listen_portaddr_hash hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.431149] 000: TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.439590] 000: TCP bind hash table entries: 4096 (order: 5, 229376 bytes, linear) [ 0.447671] 000: TCP: Hash tables configured (established 4096 bind 4096) [ 0.454812] 000: UDP hash table entries: 256 (order: 3, 32768 bytes, linear) [ 0.462112] 000: UDP-Lite hash table entries: 256 (order: 3, 32768 bytes, linear) [ 0.470006] 000: NET: Registered protocol family 1 [ 0.475421] 000: RPC: Registered named UNIX socket transport module. [ 0.481968] 000: RPC: Registered udp transport module. [ 0.487246] 000: RPC: Registered tcp transport module. [ 0.492512] 000: RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.499561] 000: PCI: CLS 0 bytes, default 64 [ 0.505130] 000: hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.518536] 000: Initialise system trusted keyrings [ 0.523757] 000: workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.537616] 000: squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.544772] 000: NFS: Registering the id_resolver key type [ 0.550439] 000: Key type id_resolver registered [ 0.555228] 000: Key type id_legacy registered [ 0.559802] 000: nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.567314] 000: 9p: Installing v9fs 9p2000 file system support [ 0.587803] 000: Key type asymmetric registered [ 0.592461] 000: Asymmetric key parser 'x509' registered [ 0.597968] 000: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.606027] 000: io scheduler mq-deadline registered [ 0.611133] 000: io scheduler kyber registered [ 0.618174] 000: pinctrl-single 4301c000.pinmux: 70 pins, size 280 [ 0.625166] 000: pinctrl-single 11c000.pinmux: 185 pins, size 740 [ 0.631744] 000: pinctrl-single 11c2e8.pinmux: 9 pins, size 36 [ 0.643144] 000: k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 0.649981] 000: k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 0.660614] 000: Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.679838] 000: brd: module loaded [ 0.693065] 000: loop: module loaded [ 0.700481] 000: libphy: Fixed MDIO Bus: probed [ 0.705776] 000: tun: Universal TUN/TAP device driver, 1.6 [ 0.712079] 000: igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.720568] 000: igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.727138] 000: sky2: driver version 1.30 [ 0.732562] 000: VFIO - User Level meta-driver version: 0.3 [ 0.738960] 000: i2c /dev entries driver [ 0.744056] 000: sdhci: Secure Digital Host Controller Interface driver [ 0.750860] 000: sdhci: Copyright(c) Pierre Ossman [ 0.756290] 000: sdhci-pltfm: SDHCI platform and OF driver helper [ 0.763644] 000: ti-sci bus@100000:bus@28380000:bus@42040000:dmsc: invalid resource [ 0.772391] 000: optee: probing for conduit method from DT. [ 0.778155] 000: optee: revision 3.8 (199fca17) [ 0.783352] 000: optee: initialized driver [ 0.788288] 000: NET: Registered protocol family 17 [ 0.793543] 000: 9pnet: Installing 9P2000 support [ 0.798452] 000: Key type dns_resolver registered [ 0.803763] 000: registered taskstats version 1 [ 0.808426] 000: Loading compiled-in X.509 certificates [ 0.000000] 000: Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.828405] 000: k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 0.835569] 000: k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 0.846355] 000: ti-sci bus@100000:bus@28380000:bus@42040000:dmsc: invalid resource [ 0.854624] 000: ti-sci bus@100000:bus@28380000:bus@42040000:dmsc: ABI: 3.1 (firmware rev 0x0015 '21.5.0--v2021.05 (Terrific Llam') [ 0.915880] 000: random: fast init done [ 0.928160] 000: omap_i2c 42120000.i2c: bus 0 rev0.12 at 100 kHz [ 0.935164] 000: omap_i2c 40b00000.i2c: bus 1 rev0.12 at 100 kHz [ 0.942396] 000: omap_i2c 2000000.i2c: bus 2 rev0.12 at 400 kHz [ 0.949177] 000: omap_i2c 2010000.i2c: bus 3 rev0.12 at 100 kHz [ 0.955897] 000: omap_i2c 2020000.i2c: bus 4 rev0.12 at 100 kHz [ 0.962606] 000: omap_i2c 2030000.i2c: bus 5 rev0.12 at 100 kHz [ 0.969510] 000: ti-sci-intr bus@100000:bus@28380000:bus@42040000:interrupt-controller2: Interrupt Router 156 domain created [ 0.981218] 000: ti-sci-intr bus@100000:interrupt-controller0: Interrupt Router 100 domain created [ 0.990601] 000: ti-sci-intr bus@100000:navss@30800000:interrupt-controller1: Interrupt Router 182 domain created [ 1.001460] 000: ti-sci-inta 33d00000.interrupt-controller: Interrupt Aggregator domain 179 created [ 1.015118] 000: k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,32] sci-dev-id:195 [ 1.025507] 000: k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: disabled [ 1.032746] 000: k3-ringacc 2b800000.ringacc: RA Proxy rev. 66348100, num_proxies:64 [ 1.043876] 000: k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:818, gp-rings[304,100] sci-dev-id:187 [ 1.054461] 000: k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: disabled [ 1.061701] 000: k3-ringacc 3c000000.ringacc: RA Proxy rev. 66348100, num_proxies:64 [ 1.070417] 000: 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 8, base_baud = 6000000) is a 8250 [ 1.080636] 000: 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 19, base_baud = 3000000) is a 8250 [ 1.089891] 000: printk: console [ttyS2] enabled [ 1.089891] 000: printk: console [ttyS2] enabled [ 1.099255] 000: printk: bootconsole [ns16550a0] disabled [ 1.099255] 000: printk: bootconsole [ns16550a0] disabled [ 1.110973] 000: 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 20, base_baud = 3000000) is a 8250 [ 1.111613] 000: omap8250 2820000.serial: unable to register 8250 port [ 1.111624] 000: omap8250 2820000.serial: PM domain pd:147 will not be powered off [ 1.180863] 000: davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 1.180881] 000: libphy: 46000f00.mdio: probed [ 1.182812] 000: davinci_mdio 46000f00.mdio: phy[3]: device 46000f00.mdio:03, driver TI DP83822 [ 1.182847] 000: am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00102, cpsw version 0x6BA80102 Ports: 2 quirks:00000000 [ 1.183324] 000: am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517 [ 1.206410] 000: am65-cpts 310d0000.cpts: CPTS ver 0x4e8a010b, freq:200000000, add_val:4 pps:0 [ 1.206958] 000: thermal thermal_zone1: failed to read out thermal zone (-22) [ 1.206987] 000: thermal thermal_zone2: failed to read out thermal zone (-22) [ 1.207816] 000: mmc0: CQHCI version 5.10 [ 1.268672] 000: mmc0: SDHCI controller on 4f80000.sdhci [4f80000.sdhci] using ADMA 64-bit [ 1.269727] 000: mmc1: CQHCI version 5.10 [ 1.340533] 000: mmc0: new HS200 MMC card at address 0001 [ 1.341237] 000: mmcblk0: mmc0:0001 IS004G 3.64 GiB [ 1.341577] 000: mmcblk0boot0: mmc0:0001 IS004G partition 1 2.00 MiB [ 1.341924] 000: mmcblk0boot1: mmc0:0001 IS004G partition 2 2.00 MiB [ 1.352551] 000: mmcblk0rpmb: mmc0:0001 IS004G partition 3 512 KiB, chardev (241:0) [ 1.361037] 000: mmcblk0: p1 p2 [ 2.275392] 000: mmc1: SDHCI controller on 4fa0000.sdhci [4fa0000.sdhci] using ADMA 64-bit [ 2.295809] 000: omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc7100 [ 2.296244] 000: omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc7100 [ 2.304920] 000: ti-udma 285c0000.dma-controller: Channels: 28 (tchan: 14, rchan: 14, gp-rflow: 16) [ 2.310855] 000: ti-udma 31150000.dma-controller: Channels: 119 (tchan: 53, rchan: 66, gp-rflow: 64) [ 2.327170] 000: 2820000.serial: ttyS4 at MMIO 0x2820000 (irq = 21, base_baud = 3000000) is a 8250 [ 2.335813] 000: mmc1: new high speed SDHC card at address e624 [ 2.343906] 000: mmcblk1: mmc1:e624 SU16G 14.8 GiB [ 2.347993] 000: mmcblk1: p1 p2 [ 2.373935] 000: spi-nor spi9.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.373961] 000: spi-nor: probe of spi9.0 failed with error -2 [ 2.412859] 000: davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 2.412871] 000: libphy: 46000f00.mdio: probed [ 2.414836] 000: davinci_mdio 46000f00.mdio: phy[3]: device 46000f00.mdio:03, driver TI DP83822 [ 2.414871] 000: am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00102, cpsw version 0x6BA80102 Ports: 2 quirks:00000000 [ 2.416587] 000: am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48 [ 2.421322] 000: am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 57.4 [ 2.421330] 000: am65-cpsw-nuss 46000000.ethernet: ALE Table size 64 [ 2.438857] 000: am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a010b, freq:200000000, add_val:4 pps:0 [ 2.454080] 000: debugfs: Directory 'pd:121' with parent 'pm_genpd' already present! [ 2.454132] 000: debugfs: Directory 'pd:120' with parent 'pm_genpd' already present! [ 2.454816] 000: debugfs: Directory 'pd:147' with parent 'pm_genpd' already present! [ 2.456280] 000: hctosys: unable to open rtc device (rtc0) [ 2.581247] 000: EXT4-fs (mmcblk1p2): recovery complete [ 2.582901] 000: EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.582976] 000: VFS: Mounted root (ext4 filesystem) on device 179:98. [ 2.590152] 000: devtmpfs: mounted [ 2.591141] 000: Freeing unused kernel memory: 1344K [ 2.591274] 000: Run /sbin/init as init process [ 2.910904] 000: systemd[1]: System time before build time, advancing clock. [ 3.004140] 000: NET: Registered protocol family 10 [ 3.009230] 000: Segment Routing with IPv6 [ 3.037048] 000: systemd[1]: systemd 243-51-gfab6f01+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.037550] 000: systemd[1]: Detected architecture arm64. [ 3.097880] 000: systemd[1]: Set hostname to . [ 3.560358] 000: random: systemd: uninitialized urandom read (16 bytes read) [ 3.560539] 000: systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [[ 3.560551] 000: systemd[1]: (This warning is only shown for the first unit using IP firewalling.) OK ] Created slice system-getty.slice[ 3.583447] 000: systemd[1]: Created slice system-getty.slice. . [ OK ] Created slice system-serial\x2dgetty[ 3.613007] 000: random: systemd: uninitialized urandom read (16 bytes read) .slice. [ 3.614178] 000: systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 3.636969] 000: random: systemd: uninitialized urandom read (16 bytes read) [[ 3.638017] 000: systemd[1]: Created slice User and Session Slice. OK ] Started Dispatch Password …ts to C[ 3.652353] 000: systemd[1]: Started Dispatch Password Requests to Console Directory Watch. onsole Directory Watch. [ OK ] Started Forward Password R…uests t[ 3.681151] 000: systemd[1]: Started Forward Password Requests to Wall Directory Watch. o Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Syslog Socket. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Temporary Directory (/tmp)... Starting Create list of st…odes for the current kernel... Starting Journal Service... Mounting Kernel Configuration File System... Starting Remount Root and Kernel File Systems... Starting Apply Kernel Variables... [ 4.087470] 000: EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) Starting udev Coldplug all Devices... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta… nodes for the current kernel. [ OK ] Started Journal Service. [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Apply Kernel Variables. Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... [ 4.349305] 000: systemd-journald[200]: Received client request to flush runtime journal. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. Starting Network Service... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Dynamic Host Configuration Protocol (DHCP). Starting System Logging Service... Starting Login Service... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting /etc/rc.local Compatibility... Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ 6.314585] 000: TI DP83822 46000f00.mdio:03: attached PHY driver [TI DP83822] (mii_bus:phy_addr=46000f00.mdio:03, irq=POLL) [ 6.336518] 000: am65-cpsw-nuss 46000000.ethernet eth0: Link is Down [ OK ] Started Login Service. [ 6.914368] 000: CAN device driver interface [ 7.047553] 000: m_can_platform 40528000.mcan: m_can device registered (irq=15, version=32) [ 7.085188] 000: davinci_mdio b132400.mdio: davinci mdio revision 1.7, bus freq 1000000 [ 7.085211] 000: libphy: b132400.mdio: probed [ 7.088938] 000: random: crng init done [ 7.088946] 000: random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Started Load/Save Random Seed. [ 7.158091] 000: davinci_mdio: probe of b132400.mdio failed with error -16 [ 7.264879] 000: davinci_mdio b232400.mdio: davinci mdio revision 1.7, bus freq 1000000 [ 7.264902] 000: libphy: b232400.mdio: probed [ 7.309093] 000: davinci_mdio b232400.mdio: phy[2]: device b232400.mdio:02, driver TI DP83867 [ 7.409410] 000: platform 41000000.r5f: configured R5F for remoteproc mode [ 7.410212] 000: platform 41000000.r5f: assigned reserved memory node r5f-dma-memory@a0000000 [ 7.410488] 000: remoteproc remoteproc0: 41000000.r5f is available [ 7.524925] 000: omap_i2c 2000000.i2c: controller timed out [ 7.599265] 000: remoteproc remoteproc0: powering up 41000000.r5f [ 7.599293] 000: remoteproc remoteproc0: Booting fw image am65x-mcu-r5f0_0-fw, size 4157212 [ 7.606891] 000: remoteproc remoteproc0: Failed to process resources: -22 [ 7.780650] 000: remoteproc remoteproc1: b034000.pru is available [ 7.780786] 000: pru-rproc b034000.pru: PRU rproc node /bus@100000/icssg@b000000/pru@34000 probed successfully [ 7.798487] 000: remoteproc remoteproc2: b004000.rtu is available [ 7.798567] 000: pru-rproc b004000.rtu: PRU rproc node /bus@100000/icssg@b000000/rtu@4000 probed successfully [ 7.799548] 000: pru-rproc b00a000.txpru: IRQ vring not found [ 7.799556] 000: pru-rproc b00a000.txpru: IRQ kick not found [ 7.799628] 000: remoteproc remoteproc3: b00a000.txpru is available [ 7.799694] 000: pru-rproc b00a000.txpru: PRU rproc node /bus@100000/icssg@b000000/txpru@a000 probed successfully [ 7.802209] 000: remoteproc remoteproc4: b038000.pru is available [ 7.802316] 000: pru-rproc b038000.pru: PRU rproc node /bus@100000/icssg@b000000/pru@38000 probed successfully [ 7.811876] 000: remoteproc remoteproc5: b006000.rtu is available [ 7.811964] 000: pru-rproc b006000.rtu: PRU rproc node /bus@100000/icssg@b000000/rtu@6000 probed successfully [ 7.821095] 000: pru-rproc b00c000.txpru: IRQ vring not found [ 7.821109] 000: pru-rproc b00c000.txpru: IRQ kick not found [ 7.821198] 000: remoteproc remoteproc6: b00c000.txpru is available [ 7.821275] 000: pru-rproc b00c000.txpru: PRU rproc node /bus@100000/icssg@b000000/txpru@c000 probed successfully [ 7.827720] 000: remoteproc remoteproc7: b134000.pru is available [ 7.827816] 000: pru-rproc b134000.pru: PRU rproc node /bus@100000/icssg@b100000/pru@34000 probed successfully [ 7.839649] 000: remoteproc remoteproc8: b104000.rtu is available [ 7.839725] 000: pru-rproc b104000.rtu: PRU rproc node /bus@100000/icssg@b100000/rtu@4000 probed successfully [ 7.839883] 000: pru-rproc b10a000.txpru: IRQ vring not found [ 7.839890] 000: pru-rproc b10a000.txpru: IRQ kick not found [ 7.839971] 000: remoteproc remoteproc9: b10a000.txpru is available [ 7.840062] 000: pru-rproc b10a000.txpru: PRU rproc node /bus@100000/icssg@b100000/txpru@a000 probed successfully [ 7.840367] 000: remoteproc remoteproc10: b138000.pru is available [ 7.840427] 000: pru-rproc b138000.pru: PRU rproc node /bus@100000/icssg@b100000/pru@38000 probed successfully [ 7.850209] 000: remoteproc remoteproc11: b106000.rtu is available [ 7.850348] 000: pru-rproc b106000.rtu: PRU rproc node /bus@100000/icssg@b100000/rtu@6000 probed successfully [ 7.866592] 000: pru-rproc b10c000.txpru: IRQ vring not found [ 7.866608] 000: pru-rproc b10c000.txpru: IRQ kick not found [ 7.866706] 000: remoteproc remoteproc12: b10c000.txpru is available [ 7.866812] 000: pru-rproc b10c000.txpru: PRU rproc node /bus@100000/icssg@b100000/txpru@c000 probed successfully [ 7.902148] 000: remoteproc remoteproc13: b234000.pru is available [ 7.902240] 000: pru-rproc b234000.pru: PRU rproc node /bus@100000/icssg@b200000/pru@34000 probed successfully [ 7.921371] 000: remoteproc remoteproc14: b204000.rtu is available [ 7.921491] 000: pru-rproc b204000.rtu: PRU rproc node /bus@100000/icssg@b200000/rtu@4000 probed successfully [ 7.921673] 000: pru-rproc b20a000.txpru: IRQ vring not found [ 7.921681] 000: pru-rproc b20a000.txpru: IRQ kick not found [ 7.921748] 000: remoteproc remoteproc15: b20a000.txpru is available [ 7.921817] 000: pru-rproc b20a000.txpru: PRU rproc node /bus@100000/icssg@b200000/txpru@a000 probed successfully [ 7.940602] 000: remoteproc remoteproc16: b238000.pru is available [ 7.940727] 000: pru-rproc b238000.pru: PRU rproc node /bus@100000/icssg@b200000/pru@38000 probed successfully [ 7.950703] 000: remoteproc remoteproc17: b206000.rtu is available [ 7.950801] 000: pru-rproc b206000.rtu: PRU rproc node /bus@100000/icssg@b200000/rtu@6000 probed successfully [ 7.961336] 000: pru-rproc b20c000.txpru: IRQ vring not found [ 7.961351] 000: pru-rproc b20c000.txpru: IRQ kick not found [ 7.961458] 000: remoteproc remoteproc18: b20c000.txpru is available [ 7.961558] 000: pru-rproc b20c000.txpru: PRU rproc node /bus@100000/icssg@b200000/txpru@c000 probed successfully [ 8.051079] 000: icssg-prueth pruss2_eth: port 1: using random MAC addr: 5e:3d:ed:69:88:62 [ 8.054584] 000: icssg-prueth pruss2_eth: TI PRU ethernet driver initialized: single EMAC mode [ 8.391987] 000: am65-cpsw-nuss 46000000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 8.392041] 000: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.585025] 000: omap_i2c 2000000.i2c: controller timed out [ 8.823513] 000: dwc3 4010000.usb: Failed to get clk 'ref': -2 [ 8.901422] 000: dwc3 4030000.usb: Failed to get clk 'ref': -2 [ 9.085492] 000: remoteproc remoteproc13: powering up b234000.pru [ 9.086852] 000: remoteproc remoteproc13: Direct firmware load for ti-pruss/am65x-sr2-pru0-prueth-fw.elf failed with error -2 [ 9.086869] 000: remoteproc remoteproc13: request_firmware failed: -2 [ 9.086876] 000: icssg-prueth pruss2_eth: failed to boot PRU0: -2 [ 9.137540] 000: remoteproc remoteproc13: powering up b234000.pru [ 9.137601] 000: remoteproc remoteproc13: Direct firmware load for ti-pruss/am65x-sr2-pru0-prueth-fw.elf failed with error -2 [ 9.137612] 000: remoteproc remoteproc13: request_firmware failed: -2 [ 9.137619] 000: icssg-prueth pruss2_eth: failed to boot PRU0: -2 [FAILED] Failed to start /etc/rc.local Compatibility. See 'systemctl status rc-local.service' for details. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Serial Getty on ttyS2. [ 9.437702] 000: usbcore: registered new interface driver usbfs [ OK ] Reached target Login Prompts. [ 9.453111] 000: usbcore: registered new interface driver hub [ 9.454731] 000: usbcore: registered new device driver usb [ OK ] Reached target Multi-User System. Starting Update UTMP about System Runlevel Changes... [ 9.526980] 000: xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 9.527025] 000: xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1 [ 9.527145] 000: xhci-hcd xhci-hcd.2.auto: hcc params 0x0298fe6d hci version 0x110 quirks 0x0000000000010010 [ OK ] Started Update UTMP about System Run[ 9.527429] 000: xhci-hcd xhci-hcd.2.auto: irq 582, io mem 0x04030000 level Changes. [ 9.527845] 000: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 9.527853] 000: usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.527859] 000: usb usb1: Product: xHCI Host Controller [ 9.527864] 000: usb usb1: Manufacturer: Linux 5.4.74-rt42-yocto-preempt-rt xhci-hcd [ 9.527868] 000: usb usb1: SerialNumber: xhci-hcd.2.auto [ 9.553323] 000: hub 1-0:1.0: USB hub found [ 9.553374] 000: hub 1-0:1.0: 1 port detected [ 9.559634] 000: xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 9.559660] 000: xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 9.559678] 000: xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 9.561191] 000: usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 9.561321] 000: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04 [ 9.561330] 000: usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.561336] 000: usb usb2: Product: xHCI Host Controller [ 9.561340] 000: usb usb2: Manufacturer: Linux 5.4.74-rt42-yocto-preempt-rt xhci-hcd [ 9.561345] 000: usb usb2: SerialNumber: xhci-hcd.2.auto [ 9.566072] 000: hub 2-0:1.0: USB hub found [ 9.572265] 000: hub 2-0:1.0: 1 port detected AX-564EB0MB1T login: