U-Boot SPL 2018.01-00569-gfd38f5a-dirty (May 31 2019 - 11:10:02) DRA722-GP ES2.0 SPL: 355 Trying to boot from MMC1 no pinctrl state for default mode no pinctrl state for default mode spl_load_image_fat_os: error reading image args, err - -2 CONFIG_SPL_LIBCOMMON_SUPPORT U-Boot 2018.01-00569-gfd38f5a-dirty (May 31 2019 - 11:10:02 +0530) CPU : DRA722-GP ES2.0 Model: TI AM5728 IDK Board: AM571x IDK REV 1.3B DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Could not get PHY for ethernet@48484000: addr 0 Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** 1490 bytes read in 3 ms (484.4 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... Running uenvcmd ... 1 bytes read in 2 ms (0 Bytes/s) Already setup. switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 4071936 bytes read in 192 ms (20.2 MiB/s) 97324 bytes read in 22 ms (4.2 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe5000, end 8ffffc2b ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (firmware@firmware-E7450) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #20 SMP PREEMPT Sat Jun 1 15:45:48 IST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM571x IDK-LCD-OSD-Display [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x0000000094000000 [ 0.000000] OMAP4: Map 0x000000009fd00000 to fe600000 for dram barrier [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @dfc3d000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129158 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=PARTUUID=30b8cffd-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 320120K/521216K available (8192K kernel code, 349K rwdata, 2604K rodata, 2048K init, 283K bss, 20872K reserved, 180224K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfd00000 ( 509 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc1057658 ( 350 kB) [ 0.000000] .bss : 0xc1059000 - 0xc109ffa0 ( 284 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000347] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000356] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000807] Console: colour dummy device 80x30 [ 0.000825] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000832] This ensures that you still see kernel messages. Please [ 0.000838] update your kernel commandline. [ 0.000857] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000872] pid_max: default: 32768 minimum: 301 [ 0.000989] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001001] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001535] CPU: Testing write buffer coherency: ok [ 0.001575] CPU0: Spectre v2: using ICIALLU workaround [ 0.001773] /cpus/cpu@0 missing clock-frequency property [ 0.001787] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039849] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059855] Hierarchical SRCU implementation. [ 0.080041] EFI services will not be available. [ 0.099914] smp: Bringing up secondary CPUs ... [ 0.099924] smp: Brought up 1 node, 1 CPU [ 0.099934] SMP: Total of 1 processors activated (12.29 BogoMIPS). [ 0.099941] CPU: All CPU(s) started in HYP mode. [ 0.099948] CPU: Virtualization extensions available. [ 0.100352] devtmpfs: initialized [ 0.118601] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.120063] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.120272] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.120290] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.124126] pinctrl core: initialized pinctrl subsystem [ 0.124622] DMI not present or invalid. [ 0.124859] NET: Registered protocol family 16 [ 0.130806] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.131687] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.324387] cpuidle: using governor ladder [ 0.324421] cpuidle: using governor menu [ 0.332429] OMAP GPIO hardware version 0.1 [ 0.359314] No ATAGs? [ 0.359363] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.359377] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.359764] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.359775] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.360352] OMAP DMA hardware revision 0.0 [ 0.392442] edma 43300000.edma: memcpy is disabled [ 0.395726] edma 43300000.edma: TI EDMA DMA engine driver [ 0.402775] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.406242] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.406451] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.406694] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.406942] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.407256] iommu: Adding device 58820000.ipu to group 1 [ 0.407350] iommu: Adding device 55020000.ipu to group 2 [ 0.407500] iommu: Adding device 40800000.dsp to group 0 [ 0.410069] palmas 0-0058: Irq flag is 0x00000004 [ 0.432815] palmas 0-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 0.434428] SMPS12: supplied by regulator-dummy [ 0.436159] SMPS3: supplied by VMAIN [ 0.437702] SMPS45: supplied by regulator-dummy [ 0.439515] SMPS6: supplied by VMAIN [ 0.441206] SMPS7: supplied by VMAIN [ 0.443136] SMPS8: supplied by VMAIN [ 0.443472] smps8: Bringing 0uV into 3300000-3300000uV [ 0.445021] random: fast init done [ 0.445340] SMPS9: supplied by VMAIN [ 0.446325] LDO1: supplied by VMAIN [ 0.451274] LDO2: supplied by VMAIN [ 0.461140] LDO3: supplied by VMAIN [ 0.471151] LDO4: supplied by VMAIN [ 0.481155] LDO5: supplied by regulator-dummy [ 0.481866] LDO6: supplied by regulator-dummy [ 0.482573] LDO7: supplied by regulator-dummy [ 0.483264] LDO8: supplied by regulator-dummy [ 0.483986] LDO9: supplied by VMAIN [ 0.491494] LDOLN: supplied by VMAIN [ 0.501214] LDOUSB: supplied by VMAIN [ 0.514273] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.514489] media: Linux media interface: v0.10 [ 0.514527] Linux video capture interface: v2.00 [ 0.514608] pps_core: LinuxPPS API ver. 1 registered [ 0.514618] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.514638] PTP clock support registered [ 0.514667] EDAC MC: Ver: 3.0.0 [ 0.520686] dmi: Firmware registration failed. [ 0.521125] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.521329] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.521708] Advanced Linux Sound Architecture Driver Initialized. [ 0.530764] clocksource: Switched to clocksource arch_sys_counter [ 0.538348] NET: Registered protocol family 2 [ 0.538889] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.538928] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.538996] TCP: Hash tables configured (established 4096 bind 4096) [ 0.539053] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.539075] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.539180] NET: Registered protocol family 1 [ 0.559541] RPC: Registered named UNIX socket transport module. [ 0.559552] RPC: Registered udp transport module. [ 0.559559] RPC: Registered tcp transport module. [ 0.559567] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.560500] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.560629] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.561727] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.565895] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.576447] NFS: Registering the id_resolver key type [ 0.576473] Key type id_resolver registered [ 0.576482] Key type id_legacy registered [ 0.576520] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.578165] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.578178] io scheduler noop registered [ 0.578187] io scheduler deadline registered [ 0.578286] io scheduler cfq registered (default) [ 0.578297] io scheduler mq-deadline registered [ 0.578306] io scheduler kyber registered [ 0.582969] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.583127] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1> [ 0.583203] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts [ 0.583215] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4 [ 0.597165] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 0.599678] V3_3D: supplied by smps9 [ 0.599943] vtt_fixed: supplied by V3_3D [ 0.642999] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.645739] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250 [ 1.608640] console [ttyS0] enabled [ 1.614103] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 1.621233] DSS: OMAP DSS rev 6.1 [ 1.626265] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 1.634767] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 1.645733] panel-dpi display: display supply vcc not found, using dummy regulator [ 1.663917] brd: module loaded [ 1.672550] loop: module loaded [ 1.679484] libphy: Fixed MDIO Bus: probed [ 1.740788] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 1.748483] davinci_mdio 48485000.mdio: detected phy mask 0 [ 1.831382] libphy: 48485000.mdio: probed [ 1.835417] davinci_mdio 48485000.mdio: phy[0]: device 48485000.mdio:00, driver unknown [ 1.843569] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driver unknown [ 1.851657] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown [ 1.859697] davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown [ 1.867780] davinci_mdio 48485000.mdio: phy[4]: device 48485000.mdio:04, driver unknown [ 1.875854] davinci_mdio 48485000.mdio: phy[5]: device 48485000.mdio:05, driver unknown [ 1.883909] davinci_mdio 48485000.mdio: phy[6]: device 48485000.mdio:06, driver unknown [ 1.891962] davinci_mdio 48485000.mdio: phy[7]: device 48485000.mdio:07, driver unknown [ 1.900000] davinci_mdio 48485000.mdio: phy[8]: device 48485000.mdio:08, driver unknown [ 1.908051] davinci_mdio 48485000.mdio: phy[9]: device 48485000.mdio:09, driver unknown [ 1.916103] davinci_mdio 48485000.mdio: phy[10]: device 48485000.mdio:0a, driver unknown [ 1.924241] davinci_mdio 48485000.mdio: phy[11]: device 48485000.mdio:0b, driver unknown [ 1.932379] davinci_mdio 48485000.mdio: phy[12]: device 48485000.mdio:0c, driver unknown [ 1.940504] davinci_mdio 48485000.mdio: phy[13]: device 48485000.mdio:0d, driver unknown [ 1.949083] davinci_mdio 48485000.mdio: phy[14]: device 48485000.mdio:0e, driver unknown [ 1.957225] davinci_mdio 48485000.mdio: phy[15]: device 48485000.mdio:0f, driver unknown [ 1.965365] davinci_mdio 48485000.mdio: phy[16]: device 48485000.mdio:10, driver unknown [ 1.973503] davinci_mdio 48485000.mdio: phy[17]: device 48485000.mdio:11, driver unknown [ 1.981641] davinci_mdio 48485000.mdio: phy[18]: device 48485000.mdio:12, driver unknown [ 1.989767] davinci_mdio 48485000.mdio: phy[19]: device 48485000.mdio:13, driver unknown [ 1.997905] davinci_mdio 48485000.mdio: phy[20]: device 48485000.mdio:14, driver unknown [ 2.006044] davinci_mdio 48485000.mdio: phy[21]: device 48485000.mdio:15, driver unknown [ 2.014184] davinci_mdio 48485000.mdio: phy[22]: device 48485000.mdio:16, driver unknown [ 2.022322] davinci_mdio 48485000.mdio: phy[23]: device 48485000.mdio:17, driver unknown [ 2.030448] davinci_mdio 48485000.mdio: phy[24]: device 48485000.mdio:18, driver unknown [ 2.038587] davinci_mdio 48485000.mdio: phy[25]: device 48485000.mdio:19, driver unknown [ 2.046724] davinci_mdio 48485000.mdio: phy[26]: device 48485000.mdio:1a, driver unknown [ 2.054861] davinci_mdio 48485000.mdio: phy[27]: device 48485000.mdio:1b, driver unknown [ 2.062999] davinci_mdio 48485000.mdio: phy[28]: device 48485000.mdio:1c, driver unknown [ 2.071137] davinci_mdio 48485000.mdio: phy[29]: device 48485000.mdio:1d, driver unknown [ 2.079263] davinci_mdio 48485000.mdio: phy[30]: device 48485000.mdio:1e, driver unknown [ 2.087424] davinci_mdio 48485000.mdio: phy[31]: device 48485000.mdio:1f, driver unknown [ 2.096362] cpsw 48484000.ethernet: Detected MACID = 30:45:11:cb:3b:ac [ 2.103005] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 2.109387] cpsw 48484000.ethernet: ALE Table size 1024 [ 2.114660] cpsw 48484000.ethernet: device node lookup for pps timer failed [ 2.121701] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies) [ 2.129608] cpsw 48484000.ethernet: cpsw: Detected MACID = 30:45:11:cb:3b:ad [ 2.138410] i2c /dev entries driver [ 2.142700] IR NEC protocol handler initialized [ 2.147252] IR RC5(x/sz) protocol handler initialized [ 2.152370] IR RC6 protocol handler initialized [ 2.156919] IR JVC protocol handler initialized [ 2.161503] IR Sony protocol handler initialized [ 2.166139] IR SANYO protocol handler initialized [ 2.170877] IR Sharp protocol handler initialized [ 2.175600] IR MCE Keyboard/mouse protocol handler initialized [ 2.181468] IR XMP protocol handler initialized [ 2.191776] sdhci: Secure Digital Host Controller Interface driver [ 2.197986] sdhci: Copyright(c) Pierre Ossman [ 2.203525] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.209970] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.215403] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 2.222083] sdhci-omap 4809c000.mmc: no pinctrl state for hs200_1_8v mode [ 2.280986] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.328252] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.338413] mmc0: new high speed SDHC card at address 59b4 [ 2.344309] mmcblk0: mmc0:59b4 00000 14.9 GiB [ 2.350326] mmcblk0: p1 p2 [ 2.353165] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.354492] ledtrig-cpu: registered to indicate activity on CPUs [ 2.356413] omap-rproc 58820000.ipu: assigned reserved memory node ipu1-memory@9d000000 [ 2.356467] remoteproc remoteproc0: 58820000.ipu is available [ 2.356656] omap-rproc 55020000.ipu: assigned reserved memory node ipu2-memory@95800000 [ 2.356705] remoteproc remoteproc1: 55020000.ipu is available [ 2.356928] omap-rproc 40800000.dsp: assigned reserved memory node dsp1-memory@99000000 [ 2.356978] remoteproc remoteproc2: 40800000.dsp is available [ 2.360306] pruss 4b200000.pruss: creating PRU cores and other child platform devices [ 2.375501] pruss 4b280000.pruss: creating PRU cores and other child platform devices [ 2.435287] davinci_mdio 4b2b2400.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 2.435292] libphy: 4b2b2400.mdio: probed [ 2.447182] davinci_mdio: probe of 4b2b2400.mdio failed with error -5 [ 2.448923] remoteproc remoteproc3: 4b234000.pru is available [ 2.448973] pru-rproc 4b234000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@34000 probed successfully [ 2.449214] remoteproc remoteproc4: 4b238000.pru is available [ 2.449250] pru-rproc 4b238000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@38000 probed successfully [ 2.449493] remoteproc remoteproc5: 4b2b4000.pru is available [ 2.449534] pru-rproc 4b2b4000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@34000 probed successfully [ 2.449762] remoteproc remoteproc6: 4b2b8000.pru is available [ 2.449802] pru-rproc 4b2b8000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@38000 probed successfully [ 2.458065] NET: Registered protocol family 10 [ 2.475199] Segment Routing with IPv6 [ 2.475244] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.475628] NET: Registered protocol family 17 [ 2.475813] Key type dns_resolver registered [ 2.475917] omap_voltage_late_init: Voltage driver support not added [ 2.475920] Power Management for TI OMAP4+ devices. [ 2.476135] Registering SWP/SWPB emulation handler [ 2.575888] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 2.585148] remoteproc remoteproc0: powering up 58820000.ipu [ 2.592032] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 2.603199] remoteproc remoteproc0: request_firmware failed: -2 [ 2.609281] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [ 2.618499] remoteproc remoteproc1: powering up 55020000.ipu [ 2.624355] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [ 2.633576] remoteproc remoteproc1: request_firmware failed: -2 [ 2.639654] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 2.648875] remoteproc remoteproc2: powering up 40800000.dsp [ 2.654733] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 2.663956] remoteproc remoteproc2: request_firmware failed: -2 [ 2.674224] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.681512] dmm 4e000000.dmm: initialized all PAT entries [ 2.711912] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.718557] [drm] No driver support for vblank timestamp query. [ 2.736513] [drm] Enabling DMM ywrap scrolling [ 2.759675] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759682] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003 [ 2.759688] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759694] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000 [ 2.759699] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=1 F=11)0x2902b [ 2.759704] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=0)0x29000 [ 2.759710] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759714] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000 [ 2.759720] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759724] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759729] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=4)0x29004 [ 2.759734] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=5)0x29005 [ 2.759739] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002 [ 2.759744] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000 [ 2.759749] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=7)0x29007 [ 2.759754] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759759] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759764] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001 [ 2.759769] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759773] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759778] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759783] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759788] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759792] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759797] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759802] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759806] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759811] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.759815] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000 [ 2.760239] mmc1: new DDR MMC card at address 0001 [ 2.760502] mmcblk1: mmc1:0001 DG4032 29.1 GiB [ 2.760618] mmcblk1boot0: mmc1:0001 DG4032 partition 1 4.00 MiB [ 2.760725] mmcblk1boot1: mmc1:0001 DG4032 partition 2 4.00 MiB [ 2.760852] mmcblk1rpmb: mmc1:0001 DG4032 partition 3 4.00 MiB [ 2.761578] mmcblk1: [ 2.825932] Console: switching to colour frame buffer device 240x75 [ 3.137911] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 3.144481] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 3.152552] prueth pruss2_eth: port 1: using random MAC addr: 82:3d:3d:de:84:93 [ 3.160416] hctosys: unable to open rtc device (rtc0) [ 3.166016] ALSA device list: [ 3.168993] No soundcards found. [ 3.967382] EXT4-fs (mmcblk0p2): recovery complete [ 3.975726] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.984022] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 3.995116] devtmpfs: mounted [ 3.999381] Freeing unused kernel memory: 2048K [ 4.301117] systemd[1]: System time before build time, advancing clock. [ 4.349490] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -ID) [ 4.371308] systemd[1]: Detected architecture arm. Welcome to Arago 2018.10! [ 4.401758] systemd[1]: Set hostname to . [ 4.811879] random: systemd: uninitialized urandom read (16 bytes read) [ 4.820178] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 4.851183] random: systemd: uninitialized urandom read (16 bytes read) [ 4.858434] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 4.901063] random: systemd: uninitialized urandom read (16 bytes read) [ 4.909196] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.940864] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 4.971491] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 5.007169] systemd[1]: Listening on Process Core Dump Socket. [ OK ] Listening on Process Core Dump Socket. [ 5.042466] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Remote File Systems. Mounting Temporary Directory (/tmp)... [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Mounting Kernel Debug File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Kernel Socket. Mounting POSIX Message Queue File System... [ OK ] Created slice system-getty.slice. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. Starting Remount Root and Kernel File Systems... [ OK ] Reached target Slices. [ 5.517122] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Journal Service. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Started Remount Root and Kernel File Systems. Starting Create System Users... Starting Rebuild Hardware Database... Starting Apply Kernel Variables... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Create System Users. [ OK ] Started Apply Kernel Variables. [ 6.007522] systemd-journald[105]: Received request to flush runtime journal from PID 1 Starting Create Static Device Nodes in /dev... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rebuild Dynamic Linker Cache... Starting Rebuild Journal Catalog... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Rebuild Journal Catalog. Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Rebuild Dynamic Linker Cache. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Started Rebuild Hardware Database. Starting Update is Completed... Starting udev Coldplug all Devices... [ OK ] Started Update is Completed. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily rotation of log files. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on dropbear.socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started System Logging Service. [ OK ] Started Kernel Logging Service. Starting TI IPC Daemon... Starting uim-sysfs.service... [ OK ] Reached target Containers. [ OK ] Started Job spooling tools. [ OK ] Started D-Bus System Message Bus. Starting RPC Bind Service... Starting Avahi mDNS/DNS-SD Stack... Starting Print notice about GPLv3 packages... [ OK ] Started Periodic Command Scheduler. Starting Login Service... Starting Network Service... Starting TI MultiCore Tools Daemon... [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Started TI IPC Daemon. [ OK ] Started RPC Bind Service. [ OK ] Found device /dev/ttyS0. [ 9.992103] random: crng init done [ 10.038860] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Started Network Service. [ 10.233807] net eth1: initializing cpsw version 1.15 (0) [FAILED] Failed to start TI MultiCore Tools Daemon. See 'systemctl status ti-mct-daemon.service' for details. [ 10.340722] prueth pruss2_eth: port 1: using random MAC addr: 0a:6a:14:07:2f:1c [ 10.357902] Generic PHY 48485000.mdio:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL) [ 10.438516] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 10.566336] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 10.860984] net eth0: initializing cpsw version 1.15 (0) [ 10.908491] prueth pruss2_eth: port 1: using random MAC addr: 56:f7:51:b2:e2:02 [ 10.965423] Generic PHY 48485000.mdio:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL) [ 11.065036] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ OK ] Started Login Service. [ OK ] Found device /dev/ttyS2. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen Backlight…ightness of backlight:backlight... Starting Wait for Network to be Configured... [ OK ] Reached target Network. Starting Enable and configure wl18xx bluetooth stack... Starting Lightning Fast Webserver With Light System Requirements... Starting Simple Network Management Protocol (SNMP) Daemon.... Starting Permit User Sessions... [ OK ] Started Redis In-Memory Data Store. Starting Network Name Resolution... [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight. [ OK ] Started Enable and configure wl18xx bluetooth stack. [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ OK ] Started Permit User Sessions. [ OK ] Started uim-sysfs.service. [ OK ] Started Network Name Resolution. [ OK ] Started Simple Network Management Protocol (SNMP) Daemon.. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started NFS status monitor for NFSv2/3 locking.. Starting rc.pvr.service... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Serial Getty on ttyS2. [ OK ] Reached target Login Prompts. Starting Synchronize System and HW clocks... [FAILED] Failed to start Synchronize System and HW clocks. See 'systemctl status sync-clocks.service' for details. [ OK ] Started rc.pvr.service. Starting weston.service... *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf bash-dev bash binutils-dev binutils bison-dev bison cifs-utils cpio cpp-symlinks cpp dosfstools elfutils-dev elfutils findutils g++-symlinks g++ gawk gcc-symlinks gcc gdb gdbc6x gdbserver gettext glmark2 gstreamer1.0-libav gzip hidapi libasm1 libcairo-perf-utils libdw1 libelf1 libgdbm-compat4 libgdbm-dev libgdbm4 libgettextlib libgettextsrc libgmp10 libidn11 libmavconn libmpc3 libmpfr4 libreadline-dev libreadline7 libunistring2 m4-dev m4 make mavlink mavros-extras mavros-msgs mavros nettle parted python3-pycairo socketcan-interface swig-dev swig which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ OK ] Started weston.service. Starting Matrix GUI... Starting telnetd.service... [ OK ] Started telnetd.service. [ OK ] Started Matrix GUI. Starting thttpd.service... [ OK ] Started thttpd.service. Starting rng-tools.service... [ OK ] Started rng-tools.service. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS0 Arago 2018.10 am57xx-evm ttyS0 am57xx-evm login: root root@am57xx-evm:~# ifconfig eth0 Link encap:Ethernet HWaddr 30:45:11:CB:3B:AC UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:82 eth1 Link encap:Ethernet HWaddr 30:45:11:CB:3B:AD UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1%775872/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:162 errors:0 dropped:0 overruns:0 frame:0 TX packets:162 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12300 (12.0 KiB) TX bytes:12300 (12.0 KiB) root@am57xx-evm:~#