U-Boot 2017.01-00458-gfd06b46-dirty (Feb 27 2019 - 17:20:47 +0800) CPU : AM437X-GP rev 1.2 I2C: ready DRAM: 1 GiB PMIC: TPS65218 MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 SF: Detected mx25l51235f with page size 256 Bytes, erase size 64 KiB, total 64 MiB, mapped at 30000000 *** Warning - bad CRC, using default environment Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! SF: Detected mx25l51235f with page size 256 Bytes, erase size 64 KiB, total 64 MiB, mapped at 30000000 device 0 offset 0x200000, size 0x400000 SF: 4194304 bytes @ 0x200000 Read: OK device 0 offset 0x100000, size 0x100000 SF: 1048576 bytes @ 0x100000 Read: OK Kernel image @ 0x82000000 [ 0x000000 - 0x3bbec8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8fff0000, end 8ffffc53 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.65-rt23 (kaka@mbdrd-centos7) (gcc version 6.2.1 20161016 (Linaro GCC 6.2-2016.11) ) #75 PREEMPT RT Mon Jul 8 15:03:02 CST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: TI AM437x SK EVM [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0xbd000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM437x ES1.2 (neon) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: console=ttyO3,115200n8 spi-ti-qspi.enable_qspi=1 root=/dev/mtdblock5 rw rootfstype=jffs2 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 976152K/1048576K available (8192K kernel code, 336K rwdata, 2572K rodata, 1024K init, 340K bss, 23272K reserved, 49152K cma-reserved, 212992K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0d54340 ( 337 kB) [ 0.000000] .bss : 0xc0d54340 - 0xc0da94f8 ( 341 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] OMAP L2C310: ROM does not support power control setting [ 0.000000] L2C-310 dynamic clock gating disabled, standby mode disabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x4e430000 [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000021] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000026] OMAP clocksource: timer1 at 24000000 Hz [ 0.000144] sched_clock: 64 bits at 500MHz, resolution 2ns, wraps every 4398046511103ns [ 0.000153] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns [ 0.000170] Switching to timer-based delay loop, resolution 2ns [ 0.000509] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000512] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000929] Console: colour dummy device 80x30 [ 0.001062] WARNING: Your 'console=ttyO3' has been replaced by 'ttyS3' [ 0.001064] This ensures that you still see kernel messages. Please [ 0.001065] update your kernel commandline. [ 0.001087] Calibrating delay loop (skipped), value calculated using timer frequency.. 1000.00 BogoMIPS (lpj=5000000) [ 0.001091] pid_max: default: 32768 minimum: 301 [ 0.001216] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001222] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002077] CPU: Testing write buffer coherency: ok [ 0.002387] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.003312] EFI services will not be available. [ 0.004118] devtmpfs: initialized [ 0.017054] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.017394] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017420] futex hash table entries: 256 (order: 1, 8192 bytes) [ 0.020846] pinctrl core: initialized pinctrl subsystem [ 0.022080] NET: Registered protocol family 16 [ 0.023580] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.042720] omap_hwmod: rtc: no dt node [ 0.042741] ------------[ cut here ]------------ [ 0.042770] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2548 _init.constprop.23+0x1fc/0x4b8 [ 0.042776] omap_hwmod: rtc: doesn't have mpu register target base [ 0.042781] Modules linked in: [ 0.042796] CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.65-rt23 #75 [ 0.042802] Hardware name: Generic AM43 (Flattened Device Tree) [ 0.042808] Backtrace: [ 0.042839] [] (dump_backtrace) from [] (show_stack+0x18/0x1c) [ 0.042849] r7:00000009 r6:00000000 r5:c0aa7dfc r4:ef065e38 [ 0.042871] [] (show_stack) from [] (dump_stack+0x24/0x28) [ 0.042885] [] (dump_stack) from [] (__warn+0xe8/0x100) [ 0.042893] [] (__warn) from [] (warn_slowpath_fmt+0x40/0x48) [ 0.042903] r9:c0c0061c r8:000000db r7:c0c3c820 r6:00000000 r5:00000000 r4:c0aa8450 [ 0.042912] [] (warn_slowpath_fmt) from [] (_init.constprop.23+0x1fc/0x4b8) [ 0.042918] r3:c0ae5728 r2:c0aa8450 [ 0.042923] r4:c0d0e6d4 [ 0.042934] [] (_init.constprop.23) from [] (__omap_hwmod_setup_all+0x48/0x124) [ 0.042943] r10:00000000 r9:c0c0061c r8:000000db r7:c0c3c820 r6:c0c49bdc r5:c0d09a30 [ 0.042947] r4:c0d0e6d4 [ 0.042958] [] (__omap_hwmod_setup_all) from [] (do_one_initcall+0x4c/0x178) [ 0.042963] r5:ffffe000 r4:c0c0d740 [ 0.042979] [] (do_one_initcall) from [] (kernel_init_freeable+0x13c/0x1cc) [ 0.042988] r10:00000003 r9:c0c0061c r8:000000db r7:c0c3c820 r6:c0c49bdc r5:c0d54340 [ 0.042992] r4:c0d54340 [ 0.043017] [] (kernel_init_freeable) from [] (kernel_init+0x10/0x110) [ 0.043026] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c08339ec [ 0.043030] r4:00000000 [ 0.043042] [] (kernel_init) from [] (ret_from_fork+0x14/0x34) [ 0.043047] r5:c08339ec r4:00000000 [ 0.043052] ---[ end trace 0000000000000001 ]--- [ 0.106148] OMAP GPIO hardware version 0.1 [ 0.121871] No ATAGs? [ 0.121900] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.121910] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.137078] edma 49000000.edma: TI EDMA DMA engine driver [ 0.140190] SCSI subsystem initialized [ 0.140573] usbcore: registered new interface driver usbfs [ 0.140632] usbcore: registered new interface driver hub [ 0.140743] usbcore: registered new device driver usb [ 0.141043] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp@44000000/l4_wkup@44c00000/scm@210000/pinmux@800/i2c0_pins, deferring probe [ 0.141097] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp@44000000/l4_wkup@44c00000/scm@210000/pinmux@800/i2c2_pins, deferring probe [ 0.141222] media: Linux media interface: v0.10 [ 0.141276] Linux video capture interface: v2.00 [ 0.141318] pps_core: LinuxPPS API ver. 1 registered [ 0.141324] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.141345] PTP clock support registered [ 0.141380] EDAC MC: Ver: 3.0.0 [ 0.142291] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.142627] Advanced Linux Sound Architecture Driver Initialized. [ 0.143731] clocksource: Switched to clocksource arm_global_timer [ 0.152734] NET: Registered protocol family 2 [ 0.153443] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.153525] TCP bind hash table entries: 8192 (order: 5, 196608 bytes) [ 0.154098] TCP: Hash tables configured (established 8192 bind 8192) [ 0.154278] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.154393] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.154765] NET: Registered protocol family 1 [ 0.155266] RPC: Registered named UNIX socket transport module. [ 0.155280] RPC: Registered udp transport module. [ 0.155285] RPC: Registered tcp transport module. [ 0.155291] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.157702] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.163529] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.164499] NFS: Registering the id_resolver key type [ 0.164540] Key type id_resolver registered [ 0.164547] Key type id_legacy registered [ 0.164588] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.164720] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.166489]erd defult) [ 0.169774] pinctrl-single 44e10800.pinmux: 9in atfe080z 796 [ 0.170449] plc gpio driver init [ 0.172901] backlight supply power not found, using dummy regulator [ 0.225058] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.227702] omap8250 481a6000.serial: No clock speed specified: using default: 48000000 [ 0.228611] 481aspciied: using default: 48000000 [ 1.133035] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 31, base_baud = 3000000) is a OMAP UART4 [ 1.142716] omap_uart 481aa000.serial: no wakeirq for uart5 [ 1.148383] omap_uart 481aa000.serial: No clock speed specified: using default: 48000000 [ 1.156575] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 32, base_baud = 3000000) is a OMAP UART5 [ 1.167086] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.173921] [drm] Initialized [ 1.190875] brd: module loaded [ 1.200296] loop: module loaded [ 1.206162] spi spi1.0: not using DMA for McSPI (-19) [ 1.212282] spi spi2.0: not using DMA for McSPI (-19) [ 1.220440] m25p80 spi0.0: mx66l51235l (65536 Kbytes) [ 1.225538] 6 ofpart partitions found on MTD device spi0.0 [ 1.231012] Creating 6 MTD partitions on "spi0.0": [ 1.235798] 0x000000000000-0x000004000000 : "QSPI.nor" [ 1.242091] 0x000000000000-0x000000080000 : "QSPI.u-boot" [ 1.248557] 0x000000080000-0x000000100000 : "QSPI.firmware" [ 1.255103] 0x000000100000-0x000000200000 : "QSPI.fdt" [ 1.261153] 0x000000200000-0x000000600000 : "QSPI.kernel" [ 1.267563] 0x000000600000-0x000004000000 : "QSPI.filesystem" [ 1.275109] libphy: Fixed MDIO Bus: probed [ 1.280187] CAN device driver interface [ 1.285199] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=218) [ 1.294993] c_can_platform 0000.can: c_can_platform device registered (regs=fa1d0000, irq=219) [ 1.304582] usbcore: registered new interface driver r8152 [ 1.310112] usbcore: registered new interface driver asix [ 1.315564] usbcore: registered new interface driver ax88179_178a [ 1.326487] xhci-hcd xhci-hcd.0.auto: xams 0x0238f06d hc in0x100 quirks 0x02010010 [ 1.385] xci-c xhci-hcd.0.auto: irq 253, io mem 0x48390000 [ 1.355836] hub 1-0:1.0: USB hub found [ 1.359625] hub 1-0:1.0: 1 port detected [ 1.364024] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.369518] xhci-hcd xhci-hcd.0.auto: new US4] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.399831] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.407897] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f06d hci version 0x100 quirks 0x02010010 [ 1.416760] xhci-hcd xhci-hcd.1.auto: irq 254, io mem 0x483d0000 [ 1.423557] hub 3-0:1.0: USB hub found [ 1.427341] hub 3-0:1.0: 1 port detected [ 1.431645] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.437139] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.444858] usb usb4S hnd [ 1.457429] hub 4-0:1.0: 1 port detected [ 1.461950] usbcore: registered new interface driver usb-storage [ 1.468301] mousedev: PS/2 mouse device common for all mice [ 1.474406] i2c /dev entries driver [ 1.478055] usbcore: registered new interface driver uvcvideo [ 1.483857] USB Viore: registered new interface driver usbhid [ 1.506795] usbhid: USB HID core driver [ 1.512862] NET: Registered protocol family 10 [ 1.518504] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.525183] NET: Registered protocol family 17 [ 1.529639] can: controller area network co 1.550490] can: netlink gateway (rev 20130117) max_hops=1 [ 1.556403] Key type dns_resolver registered [ 1.560932] omap_voltage_late_init: Voltage driver support not added [ 1.644990] omap_i2c 44e0b000.i2c: bus 0 rev0.12 at 100 kHz [ 1.677775] rtc-ds1307 2-0068: rtc core: registered ds1307 as rtc0 [ 1.683966] rtc-ds1307 2-0068: 56 bytes nvram [ 1.692885] omap_i2c 4819c000.i2c: bus 2 rev0.12 at 100 kHz [ 1.699162] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.775410] rtc-ds1307 2-0068: setting system clock to 2018-06-04 20:56:01 UTC (1528145761) [ 1.794393] ALSA device list: [ 1.797361] No soundcards found. [ 1.862580] random: fast init done [ 5.048552] VFS: Mounted root (jffs2 filesystem) on device 31:5. [ 5.055138] devtmpfs: mounted [ 5.059936] Freeing unused kernel memory: 1024K INIT: version 2.88 booting mount: mounting tmpfs on /mnt/.psplash failed: No such file or directory Starting udev [ 6.149553] udevd[130]: starting version 3.2 [ 6.277537] udevd[131]: starting eudev-3.2 [ 7.433264] remoteproc remoteproc0: wkup_m3 is available [ 8.973926] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 8.980030] davinci_mdio 4a101000.mdio: detected phy mask ffffffee [ 9.403086] libphy: 4a101000.mdio: probed [ 9.407982] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver RTL8211F Gigabit Ethernet [ 9.507445] davinci_mdio 4a101000.mdio: phy[4]: device 4a101000.mdio:04, driver RTL8211F Gigabit Ethernet [ 9.564388] cpsw 4a100000.ethernet: Detected MACID = f4:e1:1e:45:d6:57 [ 9.571051] cpsw 4a100000.ethernet: device node lookup for pps timer failed [ 9.670184] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) [ 9.724670] ti-pruss 54400000.pruss: creating PRU cores and other child platform devices [ 9.757512] remoteproc remoteproc1: 54434000.pru0 is available [ 9.763447] pru-rproc 54434000.pru0: PRU rproc node /ocp@44000000/pruss_soc_bus@54426000/pruss@54400000/pru@54434000 probed successfully [ 9.836827] remoteproc remoteproc2: 54438000.pru1 is available [ 9.842752] pru-rproc 54438000.pru1: PRU rproc node /ocp@44000000/pruss_soc_bus@54426000/pruss@54400000/pru@54438000 probed successfully [ 9.892173] prueth pruss1_eth: pruss MC Mask 0:0:0:0:0:0 [ 9.897819] prueth pruss1_eth: could not get ptp tx irq [ 9.903055] prueth pruss1_eth: port 1: using random MAC addr: 2e:b6:80:b9:f9:35 [ 9.963900] davinci_mdio 54432400.mdio: davinci mdio revision 1.6 [ 9.970000] libphy: 54432400.mdio: probed [ 10.002848] prueth pruss1_eth: pruss MC Mask 0:0:0:0:0:0 [ 10.011440] prueth pruss1_eth: could not get ptp tx irq [ 10.033008] prueth pruss1_eth: port 1: using random MAC addr: 26:87:12:61:5f:50 [ 10.051540] davinci_mdio 54432400.mdio: phy[0]: device 54432400.mdio:00, driver RTL8201F 10/100Mbps Ethernet [ 10.061783] davinci_mdio 54432400.mdio: phy[1]: device 54432400.mdio:01, driver RTL8201F 10/100Mbps Ethernet [ 10.090716] ti-pruss 54440000.pruss: creating PRU cores and other child platform devices [ 10.114266] remoteproc remoteproc3: 54474000.pru0 is available [ 10.120198] pru-rproc 54474000.pru0: PRU rproc node /ocp@44000000/pruss_soc_bus@54426000/pruss@54440000/pru@54474000 probed successfully [ 10.134815] prueth pruss1_eth: could not get ptp tx irq [ 10.134836] prueth pruss1_eth: port 2: using random MAC addr: 2a:9b:1f:6b:e5:9b [ 10.164380] remoteproc remoteproc4: 54478000.pru1 is available [ 10.170311] pru-rproc 54478000.pru1: PRU rproc node /ocp@44000000/pruss_soc_bus@54426000/pruss@54440000/pru@54478000 probed successfully INIT: Entering runlevel: 5 [ 10.238070] prueth pruss1_eth: TI PRU ethernet (type 0) driver initialized Configuring network interfaces... [ 10.749352] remoteproc remoteproc2: powering up 54438000.pru1 [ 10.758916] remoteproc remoteproc2: Booting fw image ti-pruss/am437x-pru1-prueth-fw.elf, size 5508 [ 10.768245] ti-pruss 54400000.pruss: configured system_events = 0x0060000000a00000 intr_channels = 0x0000012a host_intr = 0x0000022a [ 10.780208] remoteproc remoteproc2: remote processor 54438000.pru1 is now up [ 10.787687] net eth1: started [ 10.790730] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 11.131358] net eth0: initializing cpsw version 1.15 (0) [ 11.137670] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 11.144022] cpsw 4a100000.ethernet: ALE Table size 1024 [ 11.244755] RTL8211F Gigabit Ethernet 4a101000.mdio:04: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=4a101000.mdio:04, irq=-1) [ 11.262491] cpts ptp bc clkid 0 [ 11.268630] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready done. Starting system message bus: [ 11.444522] random: crng init done dbus. using ti_cpsw Starting syslogd/klogd: done [ 12.884408] prueth pruss1_eth eth1: Link is Up - 10Mbps/Half - flow control off [ 12.891765] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready ldconfig: /lib/ld-linux-armhf.so.3 is not a symbolic link ldconfig: /lib/libcom_err.so.2 is not a symbolic link ldconfig: /lib/libext2fs.so.2 is not a symbolic link ldconfig: /lib/libe2p.so.2 is not a symbolic link ldconfig: /usr/lib/libcurl.so.4 is not a symbolic link umount: can't unmount /mnt/.psplash: No such file or directory inifile: warning: File contains DOS-style line endings. Version=1.0.0.0 eCLR:------------------------------------------------------------------ ControllerDataSize=200000 ApplicationDataSize=5000008 ApplicationCodeSize=5000000 RetainDataSize=100016 LowerPrio=10 NormLowPrio=60 NormHighPrio=88 HighPrio=89 ScheduleCycleTime=90 EtherCATMaster:-------------------------------------------------------- EtherCATMasterEnable=1 LinkLayerType=CPSW MasterInstance=1 CycleTime=1000 MasterPrioBase=95 DcmMode=2 LicenseKey=0x0 MOTION:---------------------------------------------------------------- ISGEnable=0 SHM:------------------------------------------------------------------- SHMEnable=0 eCLRIntime -ECAT CPSW 1 1000 95 PHOENIX CONTACT Software embedded CLR Version 2.2.0.20783 for Linux.ARM fiiplc@am437x-evm:~$ I/elog [06-04 20:56:19] Logger V2.0.3 is initialize success. Open Dev /dev/plcgpio success! I/target_mb_gpio [06-04 20:56:19] gpio initialize done. [ 20.255335] spidev spi1.0: not using DMA for McSPI (-19) I/target_mb_led [06-04 20:56:19] led initialize done. [ 20.263188] spidev spi1.0: not using DMA for McSPI (-19) [ 20.273240] spidev spi1.0: not using DMA for McSPI (-19) I/target_mb_adc [06-04 20:56:19] adc select 10V.[ 20.279358] spidev spi2.0: not using DMA for McSPI (-19) I/target_mb_adc [06-04 20:56:19] adc initialize done. [ 20.288743] spidev spi2.0: not using DMA for McSPI (-19) [ 20.299418] spidev spi2.0: not using DMA for McSPI (-19) I/target_mb_dac [06-04 20:56:19] dac select 10V. I/target_mb_dac [06-04 20:56:19] dac initialize done. CRCData=0x7070 rcv numberByte=0x0, expect=0xC CRCData:16395 receive numberReg :0x0,expect NumReg:0x52 CRCData:16395 receive numberReg :0x0,expect NumReg:0x52 W/target_iob_system [06-04 20:56:19] (iob_system_set_setting:191)write io board system info error MB_Digital_IO_Write:CRCData=0x400B, expect=0 MB_Digital_IO_Write:numberByte=0x0, expect=0x8 CRCData:45928 MB_IO_Register_Read:receive numberByte :0x0,expect NumByte:0xA4 I/target_iob_system [06-04 20:56:19] I/O board SW version is: v0.0.0 I/target_iob_system [06-04 20:56:19] io board initialize done. /dev/plcgpio already open [ 20.408333] c_can_platform 481cc000.can can0: setting BTR=1c05 BRPE=0000 I/target_iom_system [06-04 20:56:22] ==================================== I/target_iom_system [06-04 20:56:22] Starting Assign IO Module Address ! I/target_iom_system [06-04 20:56:22] I/target_iom_system [06-04 20:56:25] IO module count:0 I/target_iom_system [06-04 20:56:25] Address Assignment Completed ! I/target_iom_system [06-04 20:56:25] ==================================== I/satislite_plc [06-04 20:56:26] main board hw version:1 I/satislite_plc [06-04 20:56:26] io board hw version:0 I/satislite_plc [06-04 20:56:27] satislite task init fiiplc@am437x-evm:~$ su - Password: root@am437x-evm:~# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 1 Transceiver: external Auto-negotiation: on Link detected: yes root@am437x-evm:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 4 Transceiver: external Auto-negotiation: on Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: no root@am437x-evm:~# [ 54.484303] prueth pruss1_eth eth1: Link is Down [ 56.564404] prueth pruss1_eth eth1: Link is Up - 10Mbps/Half - flow control off root@am437x-evm:~# root@am437x-evm:~# genpkt -i eth0 -[ 73.204300] prueth pruss1_eth eth1: Link is Down p rand -c 1000000 root@am437x-evm:~# root@am437x-evm:~# root@am437x-evm:~# root@am437x-evm:~# genpkt -i eth1 -p rand -c 1000000 Interface name: eth1 Source MAC: 80:2B:F9:FD:32:72 Destination MAC: 00:00:00:00:00:00 Count: 1000000 Length: 1514 Payload: random ^C root@am437x-evm:~#