U-Boot SPL 2018.01-g131dc82830 (May 08 2019 - 17:25:32) DRA752-GP ES2.0 Trying to boot from MMC1 no pinctrl state for default mode i2c_write: error waiting for addr ACK (status=0x116) tps65903x: could not set LDO1 voltage. no pinctrl state for default mode *** Warning - bad CRC, using default environment reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2018.01-g131dc82830 (May 08 2019 - 17:25:32 +0000) CPU : DRA752-GP ES2.0 Model: TI AM5728 IDK Board: Humatics ALB REV DRAM: 4 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - bad CRC, using default environment i2c_write: error waiting for data ACK (status=0x116) i2c_write: error waiting for data ACK (status=0x116) i2c_write: error waiting for data ACK (status=0x116) Warning: fastboot.board_rev: unknown board revision GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** reading uEnv.txt 574 bytes read in 3 ms (186.5 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 4014592 bytes read in 266 ms (14.4 MiB/s) 104107 bytes read in 53 ms (1.9 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe3000, end 8ffff6aa ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.40-g4796173fc5 (oe-user@oe-host) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #39 SMP PREEMPT Wed May 8 21:18:21 UTC 2019 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM5728 IDK [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node dsp2-memory@9f000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x00000000fe400000 [ 0.000000] OMAP4: Map 0x000000027fd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] percpu: Embedded 15 pages/cpu @eff33000 s31372 r8192 d21876 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 996928 [ 0.000000] Kernel command line: console=ttyO2,115200n8 root=PARTUUID=e681b4b1-02 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 3754820K/3994624K available (8192K kernel code, 291K rwdata, 2304K rodata, 2048K init, 289K bss, 51388K reserved, 188416K cma-reserved, 3380224K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc1048e98 ( 292 kB) [ 0.000000] .bss : 0xc104a000 - 0xc10925fc ( 290 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000016] Switching to timer-based delay loop, resolution 162ns [ 0.000341] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000349] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000804] Console: colour dummy device 80x30 [ 0.000822] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2' [ 0.000829] This ensures that you still see kernel messages. Please [ 0.000836] update your kernel commandline. [ 0.000857] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000872] pid_max: default: 32768 minimum: 301 [ 0.000992] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001004] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001541] CPU: Testing write buffer coherency: ok [ 0.001759] /cpus/cpu@0 missing clock-frequency property [ 0.001778] /cpus/cpu@1 missing clock-frequency property [ 0.001789] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039873] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059877] Hierarchical SRCU implementation. [ 0.080070] EFI services will not be available. [ 0.099939] smp: Bringing up secondary CPUs ... [ 0.170244] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.170338] smp: Brought up 1 node, 2 CPUs [ 0.170352] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.170359] CPU: All CPU(s) started in HYP mode. [ 0.170366] CPU: Virtualization extensions available. [ 0.170882] devtmpfs: initialized [ 0.187994] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0 [ 0.188240] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.188428] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.188445] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.192243] xor: measuring software checksum speed [ 0.290172] arm4regs : 2008.000 MB/sec [ 0.390246] 8regs : 1618.800 MB/sec [ 0.490317] 32regs : 1538.000 MB/sec [ 0.590387] neon : 2948.000 MB/sec [ 0.590396] xor: using function: neon (2948.000 MB/sec) [ 0.590409] pinctrl core: initialized pinctrl subsystem [ 0.590853] DMI not present or invalid. [ 0.591109] NET: Registered protocol family 16 [ 0.592137] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.593052] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.767856] cpuidle: using governor ladder [ 0.767890] cpuidle: using governor menu [ 0.776033] OMAP GPIO hardware version 0.1 [ 0.796908] platform 56000000.gpu: Cannot lookup hwmod 'gpu' [ 0.797192] platform 59000000.bb2d: Cannot lookup hwmod 'bb2d' [ 0.797439] platform 58000000.dss: Cannot lookup hwmod 'dss_core' [ 0.799452] platform 489d0000.vpe: Cannot lookup hwmod 'vpe' [ 0.803646] platform 58001000.dispc: Cannot lookup hwmod 'dss_dispc' [ 0.804008] platform 58040000.encoder: Cannot lookup hwmod 'dss_hdmi' [ 0.804112] No ATAGs? [ 0.804184] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.804197] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.804556] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.804567] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.805091] OMAP DMA hardware revision 0.0 [ 0.980977] raid6: int32x1 gen() 225 MB/s [ 1.151071] raid6: int32x1 xor() 260 MB/s [ 1.321174] raid6: int32x2 gen() 325 MB/s [ 1.491293] raid6: int32x2 xor() 330 MB/s [ 1.661463] raid6: int32x4 gen() 426 MB/s [ 1.831513] raid6: int32x4 xor() 349 MB/s [ 2.001629] raid6: int32x8 gen() 420 MB/s [ 2.171813] raid6: int32x8 xor() 323 MB/s [ 2.341898] raid6: neonx1 gen() 946 MB/s [ 2.512004] raid6: neonx1 xor() 959 MB/s [ 2.682129] raid6: neonx2 gen() 1317 MB/s [ 2.852220] raid6: neonx2 xor() 1718 MB/s [ 3.022334] raid6: neonx4 gen() 1924 MB/s [ 3.192437] raid6: neonx4 xor() 1817 MB/s [ 3.362569] raid6: neonx8 gen() 1714 MB/s [ 3.532661] raid6: neonx8 xor() 1477 MB/s [ 3.532669] raid6: using algorithm neonx4 gen() 1924 MB/s [ 3.532676] raid6: .... xor() 1817 MB/s, rmw enabled [ 3.532683] raid6: using neon recovery algorithm [ 3.539817] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 3.541107] edma 43300000.edma: memcpy is disabled [ 3.544279] edma 43300000.edma: TI EDMA DMA engine driver [ 3.547041] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 3.547245] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 3.547486] omap-iommu 58882000.mmu: 58882000.mmu registered [ 3.547727] omap-iommu 55082000.mmu: 55082000.mmu registered [ 3.548074] omap-iommu 41501000.mmu: 41501000.mmu registered [ 3.548292] omap-iommu 41502000.mmu: 41502000.mmu registered [ 3.548522] iommu: Adding device 58820000.ipu to group 1 [ 3.548599] iommu: Adding device 55020000.ipu to group 2 [ 3.548739] iommu: Adding device 40800000.dsp to group 0 [ 3.548983] iommu: Adding device 41000000.dsp to group 3 [ 3.549811] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz [ 3.550452] palmas 1-0058: Irq flag is 0x00000004 [ 3.584247] palmas 1-0058: Muxing GPIO 2b, PWM 0, LED 0 [ 3.585746] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 3.586149] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 3.586345] pps_core: LinuxPPS API ver. 1 registered [ 3.586355] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.586374] PTP clock support registered [ 3.586472] dmi: Firmware registration failed. [ 3.586837] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 3.587111] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 3.588053] clocksource: Switched to clocksource arch_sys_counter [ 3.595736] NET: Registered protocol family 2 [ 3.596261] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 3.596300] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 3.596368] TCP: Hash tables configured (established 4096 bind 4096) [ 3.596433] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 3.596455] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 3.596568] NET: Registered protocol family 1 [ 3.596891] RPC: Registered named UNIX socket transport module. [ 3.596901] RPC: Registered udp transport module. [ 3.596908] RPC: Registered tcp transport module. [ 3.596915] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.597779] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 3.597949] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 3.599012] workingset: timestamp_bits=14 max_order=20 bucket_order=6 [ 3.603124] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.603624] NFS: Registering the id_resolver key type [ 3.603647] Key type id_resolver registered [ 3.603655] Key type id_legacy registered [ 3.603694] ntfs: driver 2.1.32 [Flags: R/O]. [ 3.605008] bounce: pool size: 64 pages [ 3.605049] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 3.605144] io scheduler noop registered [ 3.605154] io scheduler deadline registered [ 3.605310] io scheduler cfq registered (default) [ 3.605320] io scheduler mq-deadline registered [ 3.605329] io scheduler kyber registered [ 3.609994] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 3.612601] dra7-pcie 51000000.pcie: Linked as a consumer to phy-4a094000.pciephy.1 [ 3.612970] OF: PCI: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 3.613009] OF: PCI: IO 0x20003000..0x20012fff -> 0x00000000 [ 3.613032] OF: PCI: MEM 0x20013000..0x2fffffff -> 0x20013000 [ 4.613307] dra7-pcie 51000000.pcie: phy link never came up [ 4.613441] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 4.613455] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.613466] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 4.613477] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 4.613786] PCI: bus0: Fast back to back transfers disabled [ 4.613875] PCI: bus1: Fast back to back transfers enabled [ 4.613913] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] [ 4.613931] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 4.614241] pcieport 0000:00:00.0: Signaling PME with IRQ 176 [ 4.614365] pcieport 0000:00:00.0: AER enabled with IRQ 176 [ 4.664136] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 4.666739] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 45, base_baud = 3000000) is a 8250 [ 4.667524] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 46, base_baud = 3000000) is a 8250 [ 5.783379] console [ttyS2] enabled [ 5.788724] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 5.802121] brd: module loaded [ 5.810732] loop: module loaded [ 5.817849] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [ 5.824958] libphy: Fixed MDIO Bus: probed [ 5.888082] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 5.895777] davinci_mdio 48485000.mdio: detected phy mask fffffffc [ 5.906246] libphy: 48485000.mdio: probed [ 5.910295] davinci_mdio 48485000.mdio: phy[0]: device 48485000.mdio:00, driver TI DP83822 10/100 Mbps PHY [ 5.920013] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driver TI DP83822 10/100 Mbps PHY [ 5.930371] cpsw 48484000.ethernet: Detected MACID = 88:3f:4a:4b:70:ba [ 5.936981] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 5.943387] cpsw 48484000.ethernet: ALE Table size 1024 [ 5.948659] cpsw 48484000.ethernet: device node lookup for pps timer failed [ 5.955690] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies) [ 5.963548] cpsw 48484000.ethernet: cpsw: Detected MACID = 88:3f:4a:4b:70:bb [ 5.971528] i2c /dev entries driver [ 5.979794] sdhci: Secure Digital Host Controller Interface driver [ 5.986001] sdhci: Copyright(c) Pierre Ossman [ 5.990900] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.997450] sdhci-omap 4809c000.mmc: probing yall !!!! [ 6.002885] sdhci-omap 4809c000.mmc: Got CD GPIO [ 6.007607] sdhci-omap 4809c000.mmc: mmc clock fmax=192000000 [ 6.013795] sdhci-omap 4809c000.mmc: before sdhci_omap_set_capabilities!!!! [ 6.020814] sdhci-omap 4809c000.mmc: before vqmmc [ 6.025626] sdhci-omap 4809c000.mmc: after get vqmmc [ 6.030804] sdhci-omap 4809c000.mmc: before sdhci_omap_read [ 6.036574] sdhci-omap 4809c000.mmc: before sdci_omap_write [ 6.042183] sdhci-omap 4809c000.mmc: after set capabilities [ 6.047779] sdhci-omap 4809c000.mmc: before setup host [ 6.053013] sdhci-omap 4809c000.mmc: after setup host [ 6.058102] sdhci-omap 4809c000.mmc: before iodelay pin ctrl [ 6.063792] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode [ 6.070450] sdhci-omap 4809c000.mmc: after iodelay pin ctrl [ 6.076048] sdhci-omap 4809c000.mmc: before add host [ 6.081046] add host 1 [ 6.083415] before sdhci_init [ 6.086395] after sdhci_init! [ 6.089387] after hostname [ 6.092105] host name pointer is -289248256 [ 6.092110] hostname is mmc0 [ 6.099205] host IRQ is 75 [ 6.102041] before led register [ 6.105196] before mmciowb [ 6.107911] before mmc_add_host [ 6.168262] after mmc_add_host [ 6.171354] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 6.179488] sdhci-omap 4809c000.mmc: after add host [ 6.186690] sdhci-omap 480b4000.mmc: probing yall !!!! [ 6.192147] sdhci-omap 480b4000.mmc: mmc clock fmax=96000000 [ 6.197903] sdhci-omap 480b4000.mmc: omap host bias error 2 [ 6.203550] sdhci-omap 480b4000.mmc: before sdhci_omap_set_capabilities!!!! [ 6.210580] sdhci-omap 480b4000.mmc: before vqmmc [ 6.215414] sdhci-omap 480b4000.mmc: after get vqmmc [ 6.220609] sdhci-omap 480b4000.mmc: before sdhci_omap_read [ 6.227416] sdhci-omap 480b4000.mmc: before sdci_omap_write [ 6.235067] sdhci-omap 480b4000.mmc: after set capabilities [ 6.240706] sdhci-omap 480b4000.mmc: before setup host [ 6.245919] sdhci-omap 480b4000.mmc: after setup host [ 6.251040] sdhci-omap 480b4000.mmc: no 1_8 V detected [ 6.256204] sdhci-omap 480b4000.mmc: before iodelay pin ctrl [ 6.261954] sdhci-omap 480b4000.mmc: after iodelay pin ctrl [ 6.267554] sdhci-omap 480b4000.mmc: before add host [ 6.272551] add host 1 [ 6.274918] before sdhci_init [ 6.277896] after sdhci_init! [ 6.280888] after hostname [ 6.283607] host name pointer is -289244672 [ 6.283614] hostname is mmc1 [ 6.290727] host IRQ is 76 [ 6.293564] before led register [ 6.296730] before mmciowb [ 6.299476] before mmc_add_host [ 6.307536] mmc0: host does not support reading read-only switch, assuming write-enable [ 6.317443] mmc0: new high speed SDXC card at address 0001 [ 6.323367] mmcblk0: mmc0:0001 GD4QT 119 GiB [ 6.329267] mmcblk0: p1 p2 [ 6.358107] after mmc_add_host [ 6.361270] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 6.369474] sdhci-omap 480b4000.mmc: after add host [ 6.378796] ledtrig-cpu: registered to indicate activity on CPUs [ 6.391144] NET: Registered protocol family 10 [ 6.396575] Segment Routing with IPv6 [ 6.400334] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 6.406710] NET: Registered protocol family 17 [ 6.411368] Key type dns_resolver registered [ 6.415760] omap_voltage_late_init: Voltage driver support not added [ 6.422188] Power Management for TI OMAP4+ devices. [ 6.427362] Registering SWP/SWPB emulation handler [ 6.433850] Btrfs loaded, crc32c=crc32c-generic [ 6.449713] mmc1: new DDR MMC card at address 0001 [ 6.455821] mmcblk1: mmc1:0001 IS008G 7.28 GiB [ 6.461741] hctosys: unable to open rtc device (rtc0) [ 6.467892] mmcblk1boot0: mmc1:0001 IS008G partition 1 4.00 MiB [ 6.474197] mmcblk1boot1: mmc1:0001 IS008G partition 2 4.00 MiB [ 6.480426] mmcblk1rpmb: mmc1:0001 IS008G partition 3 4.00 MiB [ 6.514784] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 6.522962] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 6.531138] devtmpfs: mounted [ 6.535386] Freeing unused kernel memory: 2048K [ 6.596677] random: fast init done [ 6.831389] systemd[1]: System time before build time, advancing clock. [ 6.873813] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -ID) [ 6.895039] systemd[1]: Detected architecture arm. Welcome to Arago 2018.04! [ 6.928992] systemd[1]: Set hostname to . [ 7.253103] random: systemd: uninitialized urandom read (16 bytes read) [ 7.260124] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 7.298187] random: systemd: uninitialized urandom read (16 bytes read) [ 7.304967] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 7.338310] random: systemd: uninitialized urandom read (16 bytes read) [ 7.345032] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 7.378313] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.408184] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 7.444825] systemd[1]: Listening on Process Core Dump Socket. [ OK ] Listening on Process Core Dump Socket. [ 7.480766] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Remote File Systems. [ OK ] Listening on Journal Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on udev Kernel Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice System Slice. Starting Journal Service... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... [ 7.895394] cryptodev: loading out-of-tree module taints kernel. [ OK ] Reached target Slices. [ 7.903215] cryptodev: driver 1.9 loaded. Mounting Kernel Debug File System... Mounting Temporary Directory (/tmp)... [ OK ] Created slice system-getty.slice. Starting Remount Root and Kernel File Systems... [ 8.039921] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Create Static Device Nodes in /dev... Mounting Kernel Configuration File System... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ 8.530412] systemd-journald[81]: Received request to flush runtime journal from PID 1 [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Flush Journal to Persistent Storage. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ 9.165674] omap-rproc 58820000.ipu: assigned reserved memory node ipu1-memory@9d000000 [ OK ] Started udev Coldplug all Devices. [ 9.184604] remoteproc remoteproc0: 58820000.ipu is available [ OK ] Reached target System Initialization. [ 9.250466] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 9.269596] remoteproc remoteproc0: powering up 58820000.ipu [ 9.275325] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 9.287679] omap-rproc 55020000.ipu: assigned reserved memory node ipu2-memory@95800000 [ 9.287785] remoteproc remoteproc1: 55020000.ipu is available [ 9.290138] omap-rproc 40800000.dsp: assigned reserved memory node dsp1-memory@99000000 [ 9.290230] remoteproc remoteproc2: 40800000.dsp is available [ 9.290716] omap-rproc 41000000.dsp: assigned reserved memory node dsp2-memory@9f000000 [ 9.290809] remoteproc remoteproc3: 41000000.dsp is available [[ 9.354705] remoteproc remoteproc0: request_firmware failed: -2 OK ] Listening on D-Bus System Message Bus Socket. [ 9.366494] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [ 9.379221] remoteproc remoteproc1: powering up 55020000.ipu [ 9.384961] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [[ 9.401111] remoteproc remoteproc1: request_firmware failed: -2 OK ] Listening on RPCbind Server Activation Socket[ 9.409944] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 . [ 9.429133] remoteproc remoteproc2: powering up 40800000.dsp [ 9.429170] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 9.429177] remoteproc remoteproc2: request_firmware failed: -2 [ 9.429229] remoteproc remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2 [ 9.429236] remoteproc remoteproc3: powering up 41000000.dsp [ 9.429263] remoteproc remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2 [ 9.429270] remoteproc remoteproc3: request_firmware failed: -2 Starting sshd.socket. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting Network Service... Starting Docker Socket for the API. [ 9.706730] palmas-rtc 48072000.i2c:tps659038@58:tps659038_rtc: rtc core: registered 48072000.i2c:tps659038@58:tps659038_rtc as rtc0 [ 9.737839] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 9.740152] omap-des 480a5000.des: will run requests pump with realtime priority [ OK ] Listening on sshd.socket. [ 9.876352] omap_gpio 48057000.gpio: Could not set line 16 debounce to 20000 microseconds (-22) [ OK ] Listening on Docker Socket for the API. [ 9.925190] omap_rtc 48838000.rtc: registered as rtc1 [ OK ] Found device /dev/ttyS2. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting RPC Bind Service... [ OK ] Reached target Containers. [ OK ] Started Kernel Logging Service. Starting telnetd.service... [ OK ] Started System Logging Service. Starting Print notice about GPLv3 packages... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting Network Time Service (one-shot ntpdate mode)... [ 10.397950] net eth1: initializing cpsw version 1.15 (0) [ 10.421688] random: crng init done [ 10.425112] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Started Periodic Command Scheduler. Starting tiipclad-daemon.service... [ OK ] Started Job spooling tools. [ 10.521247] TI DP83822 10/100 Mbps PHY 48485000.mdio:01: attached PHY driver [TI DP83822 10/100 Mbps PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL) Starting Login Service... [ OK ] Started Network Service. [ OK ] Started RPC Bind Service. [ OK ] Started telnetd.service. [ 10.581714] cpts ptp bc clkid 0 [ OK ] Started Network Time Service (one-shot ntpdate mode). [ 10.595001] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Starting NTP client/server... Starting Wait for Network to be Configured... [ OK ] Reached target Network. [ 10.639746] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 10.647740] net eth0: initializing cpsw version 1.15 (0) Starting Network Name Resolution... Starting DNS forwarder and DHCP server... Starting Permit User Sessions... [ OK ] Started Login Service. [ OK ] Started tiipclad-daemon.service. Starting thttpd.service... [ 10.761456] TI DP83822 10/100 Mbps PHY 48485000.mdio:00: attached PHY driver [TI DP83822 10/100 Mbps PHY] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL) [ 10.779575] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ OK ] Started Permit User Sessions. [ OK ] Started NTP client/server. [ OK ] Started Serial Getty on ttyS2. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. Starting Synchronize System and HW clocks... [ 10.854678] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ OK ] Started thttpd.service. Starting rng-tools.service... [ 10.930641] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [FAILED] Failed to start DNS forwarder and DHCP serv[ 10.939746] CAN device driver interface er. See 'systemctl status dnsmasq.service' for details. [ OK ] Started Synchronize System and HW clocks. [ 10.966046] omap-aes 4b500000.aes: will run requests pump with realtime priority [ OK ] Started Network Name Resolution. [ OK ] Started rng-tools.service. Starting thermal-zone-init.service... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started thermal-zone-init.service. [ 11.153186] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 11.159294] omap-aes 4b700000.aes: will run requests pump with realtime priority [ 11.182571] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=91) [ 11.346757] pruss 4b200000.pruss: creating PRU cores and other child platform devices [ 11.379718] pruss 4b280000.pruss: creating PRU cores and other child platform devices [ 11.468656] davinci_mdio 4b2b2400.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 11.483592] libphy: 4b2b2400.mdio: probed [ 11.522981] davinci_mdio 4b2b2400.mdio: phy[0]: device 4b2b2400.mdio:00, driver TI DP83822 10/100 Mbps PHY [ 11.544690] davinci_mdio 4b2b2400.mdio: phy[1]: device 4b2b2400.mdio:01, driver TI DP83822 10/100 Mbps PHY [ 11.725071] remoteproc remoteproc4: 4b234000.pru is available [ 11.739478] pru-rproc 4b234000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@34000 probed successfully [ 11.764809] remoteproc remoteproc5: 4b238000.pru is available [ 11.776079] pru-rproc 4b238000.pru: PRU rproc node /ocp/pruss_soc_bus@4b226004/pruss@0/pru@38000 probed successfully [ 11.792553] remoteproc remoteproc6: 4b2b4000.pru is available [ 11.801722] pru-rproc 4b2b4000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@34000 probed successfully [ 11.879945] remoteproc remoteproc7: 4b2b8000.pru is available [ 11.896439] pru-rproc 4b2b8000.pru: PRU rproc node /ocp/pruss_soc_bus@4b2a6004/pruss@0/pru@38000 probed successfully [ 11.943893] prueth pruss2_eth: pruss MC Mask 0:0:0:0:0:0 [ 11.959071] prueth pruss2_eth: port 1: using random MAC addr: aa:74:33:f8:25:c1 [ 12.099652] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 12.132168] prueth pruss2_eth: port 2: using random MAC addr: 0e:d6:f3:e3:83:e3 [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ 12.246732] prueth pruss2_eth: request for sync latch pins failed: -19 [ 12.295310] prueth pruss2_eth: TI PRU ethernet (type 0) driver initialized *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: bash binutils cifs-utils cpio cpp-symlinks cpp dnsmasq dosfstools elfutils gawk gdb gdbserver gzip libdw1 libelf1 libgdbm-compat4 libgdbm4 libgmp10 libidn11 libmpc3 libmpfr4 libreadline7 libunistring2 m4 nettle python3-rfc3987 python3-strict-rfc3339 rsync which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ 12.883865] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 12.895726] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.137951] dwc3 48890000.usb: failed to initialize core [ 13.163615] dwc3 488d0000.usb: failed to initialize core [ 13.517417] remoteproc remoteproc6: powering up 4b2b4000.pru [ 13.526980] remoteproc remoteproc6: Booting fw image ti-pruss/am57xx-pru0-prueth-fw.elf, size 5028 [ 13.548521] pruss 4b280000.pruss: configured system_events = 0x0000060000500000 intr_channels = 0x00000095 host_intr = 0x00000115 [ 13.568256] remoteproc remoteproc6: remote processor 4b2b4000.pru is now up [ 13.575469] net eth2: started [ 13.582362] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 13.616598] remoteproc remoteproc7: powering up 4b2b8000.pru [ 13.623837] remoteproc remoteproc7: Booting fw image ti-pruss/am57xx-pru1-prueth-fw.elf, size 5060 [ 13.636222] pruss 4b280000.pruss: configured system_events = 0x0060000000a00000 intr_channels = 0x0000012a host_intr = 0x0000022a [ 13.650191] remoteproc remoteproc7: remote processor 4b2b8000.pru is now up [ 13.657465] net eth3: started [ 13.664287] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am57xx-evm ttyS2 Arago 2018.04 am57xx-evm ttyS2 am57xx-evm login: