Welcome to use TQ3358 Board! U-Boot SPL 2011.09 (Mar 30 2017 - 11:05:26) Texas Instruments Revision detection unimplemented boot from NAND... U-Boot 2011.09 (Mar 30 2017 - 11:05:26) I2C: ready DRAM: 512 MiB NAND: *************NAND:1024 MiB *************NAND:1024 MiB MMC: OMAP SD/MMC: 0 Net: cpsw ##### EmbedSky BIOS for TQ3358 ##### This Board: SDRAM is 512MB; Hit any key to stop autoboot: 0 setting bootargs ... bootargs=setenv bootargs console=ttyO0,115200n8 androidboot.console=ttySAC0 root=ubi0:rootfs rw ubi.mtd=8 rootfstype=ubifs rootwait=1 ip=none lcd=X800Y480 uart1_d_can=uart1 uart2_i2c2=uart2 Booting from nand ... NAND read: device 0 offset 0x580000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0x60000, size 0x20000 131072 bytes read: OK ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-4.4.32-gadde2ca9f8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3645304 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 XIP Kernel Image ... OK OK Loading Device Tree to 9fec3000, end 9fecfe54 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 4.4.32-gadde2ca9f8 (root@semiyd-VirtualBox) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #54 PREEMPT Fri Apr 21 14:02:32 CST 2017 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: TI AM335x EVM cma: Reserved 48 MiB at 0x9c800000 Memory policy: Data cache writeback CPU: All CPU(s) started in SVC mode. AM335X ES2.1 (sgx neon ) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 Kernel command line: setenv bootargs console=ttyO0,115200n8 androidboot.console=ttySAC0 root=ubi0:rootfs rw ubi.mtd=8 rootfstype=ubifs rootwait=1 ip=none lcd=X800Y480 uart1_d_can=uart1 uart2_i2c2=uart2 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 459192K/524288K available (6899K kernel code, 325K rwdata, 2448K rodata, 640K init, 269K bss, 15944K reserved, 49152K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0929014 (9349 kB) .init : 0xc092a000 - 0xc09ca000 ( 640 kB) .data : 0xc09ca000 - 0xc0a1b7b0 ( 326 kB) .bss : 0xc0a1b7b0 - 0xc0a5ec58 ( 270 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. NR_IRQS:16 nr_irqs:16 16 IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts OMAP clockevent source: timer2 at 24000000 Hz sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns OMAP clocksource: timer1 at 24000000 Hz clocksource_probe: no matching clocksources found Console: colour dummy device 80x30 Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys io Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys perf_event Initializing cgroup subsys pids CPU: Testing write buffer coherency: ok Setting up static identity map for 0x80008200 - 0x80008258 devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 omap_hwmod: debugss: _wait_target_disable failed clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu OMAP GPIO hardware version 0.1 omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_s0, deferring probe hw-breakpoint: debug architecture 0x4 unsupported. edma 49000000.edma: TI EDMA DMA engine driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c1_pins, deferring probe omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered EDAC MC: Ver: 3.0.0 omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource timer1 NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available futex hash table entries: 256 (order: -1, 3072 bytes) NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered ntfs: driver 2.1.32 [Flags: R/O]. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 omap_uart 44e09000.serial: no wakeirq for uart0 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a OMAP UART0 console [ttyO0] enabled [drm] Initialized drm 1.1.0 20060810 [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [drm] No driver support for vblank timestamp query. Console: switching to colour frame buffer device 100x30 tilcdc 4830e000.lcdc: fb0: frame buffer device [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 loop: module loaded libphy: Fixed MDIO Bus: probed davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 davinci_mdio 4a101000.mdio: detected phy mask ffffffd0 libphy: 4a101000.mdio: probed davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver RTL8211E Gigabit Ethernet davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver unknown davinci_mdio 4a101000.mdio: phy[2]: device 4a101000.mdio:02, driver unknown davinci_mdio 4a101000.mdio: phy[3]: device 4a101000.mdio:03, driver unknown davinci_mdio 4a101000.mdio: phy[5]: device 4a101000.mdio:05, driver RTL8211E Gigabit Ethernet cpsw 4a100000.ethernet: Detected MACID = 68:9e:19:89:34:de cpsw 4a100000.ethernet: cpts: overflow check period 850 cpsw 4a100000.ethernet: cpsw: Detected MACID = 68:9e:19:89:34:e0 usbcore: registered new interface driver uas usbcore: registered new interface driver usb-storage usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-cypress usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums_eneub6250 usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-karma usbcore: registered new interface driver ums-onetouch usbcore: registered new interface driver ums-realtek usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat 47401300.usb-phy supply vcc not found, using dummy regulator musb-hdrc musb-hdrc.0.auto: Failed to request rx1. musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517 47401b00.usb-phy supply vcc not found, using dummy regulator musb-hdrc musb-hdrc.1.auto: Failed to request rx1. musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517 mousedev: PS/2 mouse device common for all mice i2c /dev entries driver cpuidle: enable-method property 'ti,am3352' found operations omap_hsmmc 48060000.mmc: Got CD GPIO omap_hsmmc 48060000.mmc: Got WP GPIO ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver remoteproc0: wkup_m3 is available remoteproc0: Note: remoteproc is still under development and considered experimental. remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 remoteproc0: failed to load am335x-pm-firmware.elf NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Key type dns_resolver registered omap_voltage_late_init: Voltage driver support not added backlight supply power not found, using dummy regulator omap-gpmc 50000000.gpmc: GPMC revision 6.0 gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 nand: device found, Manufacturer ID: 0x01, Chip ID: 0xd3 nand: AMD/Spansion S34ML08G1 nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme 9 ofpart partitions found on MTD device 8000000.nand Creating 9 MTD partitions on "8000000.nand": 0x000000000000-0x000000020000 : "NAND.SPL" 0x000000020000-0x000000040000 : "NAND.SPL.backup1" 0x000000040000-0x000000060000 : "NAND.SPL.backup2" 0x000000060000-0x000000080000 : "NAND.SPL.backup3" 0x000000080000-0x000000260000 : "NAND.u-boot" 0x000000260000-0x000000280000 : "NAND.u-boot-env" 0x000000280000-0x000000580000 : "NAND.LOGO" 0x000000580000-0x000000a80000 : "NAND.kernel" 0x000000a80000-0x000040000000 : "rootfs" tps65910 0-002d: No interrupt support, no core IRQ tps65910-rtc tps65910-rtc: IRQ is not free. tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0 at24 0-0052: 65536 byte 24c512 EEPROM, writable, 1 bytes/write omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected omap_hsmmc 48060000.mmc: Got CD GPIO omap_hsmmc 48060000.mmc: Got WP GPIO vmmc: supplied by vbat asoc-simple-card sound: tlv320aic32x4-hifi <-> 48038000.mcasp mapping ok vdd_mpu: supplied by vbat ubi0: attaching mtd8 ubi0: scanning is finished ubi0: attached mtd8 (name "rootfs", size 1013 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 512 (aligned 512), data offset: 2048 ubi0: good PEBs: 8108, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 103015119 ubi0: available PEBs: 0, total reserved PEBs: 8108, PEBs reserved for bad PEB handling: 160 ubi0: background thread "ubi_bgt0d" started, PID 68 <<-GTP-INFO->> GTP driver installing... <<-GTP-INFO->> GTP Driver Version: V2.0<2013/08/28> <<-GTP-INFO->> GTP I2C Address: 0x5d <<-GTP-INFO->> Guitar reset <<-GTP-INFO->> IC Version: 911_1050 <<-GTP-INFO->> CTP_CONFIG_GROUP1 used, config length: 186 <<-GTP-INFO->> Driver send config. <<-GTP-INFO->> X_MAX: 480, Y_MAX: 800, TRIGGER: 0x00 input: Capacitance_ts as /devices/virtual/input/input0 <<-GTP-INFO->> GTP works in interrupt mode. <<-GTP-INFO->> Applied memory size:2562. <<-GTP-INFO->> I2C function: without pre and end cmd! tps65910-rtc tps65910-rtc: setting system clock to 2017-02-14 02:44:20 UTC (1487040260) lis3_reg: disabling wlan-en-regulator: disabling ALSA device list: #0: tlv320aic32x4 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 70 UBIFS (ubi0:0): recovery needed UBIFS (ubi0:0): recovery completed UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 1023547392 bytes (976 MiB, 7933 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 76DBDDD3-8302-48F0-8DFA-B17E7B2D7A66, small LPT model VFS: Mounted root (ubifs filesystem) on device 0:15. devtmpfs: mounted Freeing unused kernel memory: 640K (c092a000 - c09ca000) This architecture does not have kernel memory protection. random: systemd: uninitialized urandom read (16 bytes read, 23 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 23 bits of entropy available) systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) systemd[1]: Detected architecture arm. Welcome to Arago 2016.10! systemd[1]: Set hostname to . random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 24 bits of entropy available) random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 24 bits of entropy available) random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 24 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 24 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 24 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 25 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 25 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 25 bits of entropy available) systemd[1]: [/lib/systemd/system/gadget-init.service:15] Unknown lvalue 'ExecStopPre' in section 'Service' systemd[1]: sockets.target: Found ordering cycle on sockets.target/start systemd[1]: sockets.target: Found dependency on rpcbind.socket/start systemd[1]: sockets.target: Found dependency on sysinit.target/start systemd[1]: sockets.target: Found dependency on alignment.service/start systemd[1]: sockets.target: Found dependency on basic.target/start systemd[1]: sockets.target: Found dependency on sockets.target/start systemd[1]: sockets.target: Breaking ordering cycle by deleting job rpcbind.socket/start systemd[1]: rpcbind.socket: Job rpcbind.socket/start deleted to break ordering cycle starting with sockets.target/start [ SKIP ] Ordering cycle found, skipping RPCbind Server Activation Socket systemd[1]: sockets.target: Found ordering cycle on sockets.target/start systemd[1]: sockets.target: Found dependency on dbus.socket/start systemd[1]: sockets.target: Found dependency on sysinit.target/start systemd[1]: sockets.target: Found dependency on alignment.service/start systemd[1]: sockets.target: Found dependency on basic.target/start systemd[1]: sockets.target: Found dependency on sockets.target/start systemd[1]: sockets.target: Breaking ordering cycle by deleting job dbus.socket/start systemd[1]: dbus.socket: Job dbus.socket/start deleted to break ordering cycle starting with sockets.target/start [ SKIP ] Ordering cycle found, skipping D-Bus System Message Bus Socket systemd[1]: sockets.target: Found ordering cycle on sockets.target/start systemd[1]: sockets.target: Found dependency on avahi-daemon.socket/start systemd[1]: sockets.target: Found dependency on sysinit.target/start systemd[1]: sockets.target: Found dependency on alignment.service/start systemd[1]: sockets.target: Found dependency on basic.target/start systemd[1]: sockets.target: Found dependency on sockets.target/start systemd[1]: sockets.target: Breaking ordering cycle by deleting job avahi-daemon.socket/start systemd[1]: avahi-daemon.socket: Job avahi-daemon.socket/start deleted to break ordering cycle starting with sockets.target/start [ SKIP ] Ordering cycle found, skipping Avah...S/DNS-SD Stack Activation Socket systemd[1]: sockets.target: Found ordering cycle on sockets.target/start systemd[1]: sockets.target: Found dependency on dropbear.socket/stop systemd[1]: sockets.target: Found dependency on sysinit.target/start systemd[1]: sockets.target: Found dependency on alignment.service/start systemd[1]: sockets.target: Found dependency on basic.target/start systemd[1]: sockets.target: Found dependency on sockets.target/start systemd[1]: sockets.target: Breaking ordering cycle by deleting job dropbear.socket/stop systemd[1]: dropbear.socket: Job dropbear.socket/stop deleted to break ordering cycle starting with sockets.target/start [ SKIP ] Ordering cycle found, skipping dropbear.socket systemd[1]: basic.target: Found ordering cycle on basic.target/start systemd[1]: basic.target: Found dependency on sysinit.target/start systemd[1]: basic.target: Found dependency on alignment.service/start systemd[1]: basic.target: Found dependency on basic.target/start systemd[1]: basic.target: Breaking ordering cycle by deleting job alignment.service/start systemd[1]: alignment.service: Job alignment.service/start deleted to break ordering cycle starting with basic.target/start [ SKIP ] Ordering cycle found, skipping alignment.service systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Mounting Temporary Directory... Mounting Temporary Directory... cryptodev: driver 1.8 loaded. systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... systemd[1]: Mounting Debug File System... Mounting Debug File System... systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. systemd[1]: Reached target Paths. [ OK ] Reached target Paths. systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Reached target Sockets. [ OK ] Reached target Sockets. systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. systemd[1]: Mounted Temporary Directory. [ OK ] Mounted Temporary Directory. systemd[1]: Started Load Kernel Modules. [ OK ] Started Load Kernel Modules. systemd[1]: Started Remount Root and Kernel File Systems. [ OK ] Started Remount Root and Kernel File Systems. systemd[1]: Started Setup Virtual Console. [ OK ] Started Setup Virtual Console. systemd[1]: Started Create list of required static device nodes for the current kernel. [ OK ] Started Create list of required sta...ce nodes for the current kernel. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Starting Create Static Device Nodes in /dev... Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. systemd-journald[115]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Load/Save Random Seed... [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started udev Coldplug all Devices. omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ OK ] Found device /dev/ttyO0. [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen Backlight...htness of backlight:backlight... Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlvirtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) ight. virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) [ OK ] Started Network Time Synchronization. virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) Error: Driver 'asoc-simple-card' is already registered, aborting... virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) [drm] Initialized pvr 1.14.3699939 20110701 on minor 1 virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) Error: Driver 'asoc-simple-card' is already registered, aborting... virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) virtio_ring: exports duplicate symbol virtio_break_device (owned by kernel) [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Sound Card. [ OK ] Reached target System Time Synchronized. Starting Synchronize System and HW clocks... [ OK ] Started Synchronize System and HW clocks. [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. Starting Permit User Sessions... [ OK ] Started Kernel Logging Service. Starting uim-sysfs.service... [ OK ] Started System Logging Service. Starting Network Service... [ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf. Starting Save/Restore Sound Card State... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting Print notice about GPLv3 packages... [ OK ] Started Permit User Sessions. [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Network Service. net eth1: initializing cpsw version 1.12 (0) net eth0: initialized cpsw ale version 1.4 net eth0: ALE Table size 1024 net eth1: phy found : id is : 0x221430 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready net eth0: initializing cpsw version 1.12 (0) net eth0: phy found : id is : 0x1cc915 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ OK ] Started uim-sysfs.service. cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Starting rc.pvr.service... [ OK ] Reached target Network. Starting Lightning Fast Webserver With Light System Requirements... Starting Network Name Resolution... [ OK ] Started Serial Getty on ttyO0. [ OK ] Started Getty on tty1. PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ] [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ OK ] Started Network Name Resolution. [ OK ] Started rc.pvr.service. Starting weston.service... Starting LSB: Dropbear Secure Shell server... [ OK ] Started weston.service. Starting telnetd.service... [ OK ] Started telnetd.service. [ OK ] Started LSB: Dropbear Secure Shell server. Starting busybox-udhcpd.service... Starting thttpd.service... [ OK ] Started busybox-udhcpd.service. [ OK ] Started thttpd.service. Starting rng-tools.service... [ OK ] Started rng-tools.service. random: nonblocking pool is initialized Starting matrix-gui-2.0.service... [ OK ] Started matrix-gui-2.0.service. Starting thermal-zone-init.service... Starting parse-ip.service... [ OK ] Started thermal-zone-init.service. [ OK ] Started parse-ip.service. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2016.10 am335x-evm ttyO0 am335x-evm login: *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf binutils bison-dev bison cpp-symlinks cpp dosfstools g++-symlinks g++ gawk-dev gawk gcc-symlinks gcc gdb gdbserver gstreamer1.0-libav hidapi libcairo-perf-utils libgmp10 libidn11 libmpc3 libmpfr4 m4-dev m4 make nettle swig-dev swig If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** ***************************************************************