U-Boot SPL 2019.01-gae9a73a-dirty (Apr 29 2021 - 08:52:06 +0530) Trying to boot from USB USB0: Register 2000440 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! U-Boot 2019.01-gae9a73a-dirty (Apr 29 2021 - 08:52:06 +0530) CPU : AM437X-GP rev 1.2 Model: TI AM437x HW PLATFORM DRAM: 512 MiB PMIC: TPS65218 NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... ** No device specified ** Net: Warning: ethernet@4a100000 using MAC address from ROM eth0: ethernet@4a100000 Hit any key to stop autoboot: 2 1 0 Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! starting USB... USB0: Register 2000440 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade Type: Removable Hard Disk Capacity: 14875.0 MB = 14.5 GB (30464000 x 512) ... is now current device Card did not respond to voltage select! 4899328 bytes read in 205 ms (22.8 MiB/s) 48902 bytes read in 17 ms (2.7 MiB/s) Booting from usb 0... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8fff1000, end 8fffff05 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.160-rt69-gb3a2247aae (oe-user@oe-host) (gcc version 8.3.0 (GCC)) #1 PREEMPT RT Thu Apr 29 13:49:01 UTC 2021 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM437x FSP-SmallPanel-RefHw-Rev-2.0-30-04-2021-17 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x9d000000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM437x ES1.2 (sgx neon) [ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x44c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/sda2 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 456392K/524288K available (9162K kernel code, 385K rwdata, 3216K rodata, 328K init, 293K bss, 18744K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (9164 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) ( 328 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 386 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 294 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0e030000 -> 0x3e430000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] OMAP L2C310: ROM does not support power control setting [ 0.000000] L2C-310 dynamic clock gating disabled, standby mode disabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x4e430000 [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000013] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000024] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000031] OMAP clocksource: timer1 at 24000000 Hz [ 0.000446] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000452] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000843] Console: colour dummy device 80x30 [ 0.000972] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000974] This ensures that you still see kernel messages. Please [ 0.000976] update your kernel commandline. [ 0.001011] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896) [ 0.060180] pid_max: default: 32768 minimum: 301 [ 0.060324] Security Framework initialized [ 0.060437] AppArmor: AppArmor initialized [ 0.060501] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060512] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.061417] CPU: Testing write buffer coherency: ok [ 0.061472] CPU0: Spectre v2: using BPIALL workaround [ 0.062535] Setting up static identity map for 0x80008200 - 0x80008278 [ 0.062835] rcu: Hierarchical SRCU implementation. [ 0.063586] EFI services will not be available. [ 0.064262] devtmpfs: initialized [ 0.075552] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.076009] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.076037] futex hash table entries: 256 (order: 1, 8192 bytes) [ 0.079787] pinctrl core: initialized pinctrl subsystem [ 0.080797] DMI not present or invalid. [ 0.081363] NET: Registered protocol family 16 [ 0.083263] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.157177] audit: initializing netlink subsys (disabled) [ 0.160293] audit: type=2000 audit(0.150:1): state=initialized audit_enabled=0 res=1 [ 0.176241] No ATAGs? [ 0.176264] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.176284] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.194127] edma 49000000.edma: TI EDMA DMA engine driver [ 0.195388] reg-fixed-voltage amplifier: Failed to allocate supply name [ 0.195407] reg-fixed-voltage: probe of amplifier failed with error -12 [ 0.198277] SCSI subsystem initialized [ 0.198534] usbcore: registered new interface driver usbfs [ 0.198603] usbcore: registered new interface driver hub [ 0.198733] usbcore: registered new device driver usb [ 0.199385] media: Linux media interface: v0.10 [ 0.199432] videodev: Linux video capture interface: v2.00 [ 0.199570] pps_core: LinuxPPS API ver. 1 registered [ 0.199578] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.199601] PTP clock support registered [ 0.199640] EDAC MC: Ver: 3.0.0 [ 0.200979] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.201784] Advanced Linux Sound Architecture Driver Initialized. [ 0.203109] clocksource: Switched to clocksource timer1 [ 0.203981] AppArmor: AppArmor Filesystem Enabled [ 0.213321] NET: Registered protocol family 2 [ 0.214222] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 7168 bytes) [ 0.214275] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.214327] TCP bind hash table entries: 4096 (order: 4, 98304 bytes) [ 0.214614] TCP: Hash tables configured (established 4096 bind 4096) [ 0.214809] UDP hash table entries: 256 (order: 2, 16384 bytes) [ 0.214887] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes) [ 0.215224] NET: Registered protocol family 1 [ 0.215940] RPC: Registered named UNIX socket transport module. [ 0.215955] RPC: Registered udp transport module. [ 0.215960] RPC: Registered tcp transport module. [ 0.215966] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.218317] Initialise system trusted keyrings [ 0.218699] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.224730] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.225610] NFS: Registering the id_resolver key type [ 0.225660] Key type id_resolver registered [ 0.225667] Key type id_legacy registered [ 0.225720] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.637878] NET: Registered protocol family 38 [ 0.637907] Key type asymmetric registered [ 0.637916] Asymmetric key parser 'x509' registered [ 0.638011] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.638023] io scheduler noop registered [ 0.638030] io scheduler deadline registered [ 0.638348] io scheduler cfq registered (default) [ 0.638362] io scheduler mq-deadline registered [ 0.638369] io scheduler kyber registered [ 0.642747] pinctrl-single 44e10800.pinmux: 199 pins, size 796 [ 0.646797] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 0.646923] pwm-backlight backlight: Linked as a consumer to [ 3.604361] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 3.614286] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 3.624588] sd 0:0:0:0: [sda] 30464000 512-byte logical blocks: (15.6 GB/14.5 GiB) [ 3.625628] sd 0:0:0:0: [sda] Write Protect is off [ 3.626198] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.634240] sda: sda1 sda2 [ 3.637255] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 3.657411] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 3.664399] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 3.718801] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 3.726592] VFS: Mounted root (ext4 filesystem) on device 8:2. [ 3.739926] devtmpfs: mounted [ 3.743621] Freeing unused kernel memory: 328K [ 3.748086] This architecture does not have kernel memory protection. [ 3.754554] Run /sbin/init as init process INIT: version 2.88 booting Framebuffer /dev/fb0 not detected Boot splashscreen disabled Starting board_start /etc/resolv.conf net.ipv6.conf.default.hop_limit = 128 net.ipv6.conf.all.hop_limit = 128 Starting udev [ 4.633973] udevd[138]: starting version 3.2.7 [ 4.686568] udevd[138]: specified group 'kvm' unknown [ 4.737627] udevd[139]: starting eudev-3.2.7 [ 4.893444] mstp_cmnet: loading out-of-tree module taints kernel. [ 4.900017] mstp_cmnet: module verification failed: signature and/or required key missing - tainting kernel [ 5.013483] Initializing MS/TP network device driver version 1.01-016 [ 5.262312] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 5.271778] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 5.380563] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 5.403332] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 5.422558] remoteproc remoteproc0: wkup_m3 is available [ 5.434385] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 5.434527] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 5.434651] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 5.474231] omap_rtc 44e3e000.rtc: registered as rtc0 [ 5.475054] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 5.475169] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 5.475294] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 5.489359] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 5.489467] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 5.489593] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 5.490504] remoteproc remoteproc0: powering up wkup_m3 [ 5.508133] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 243020 [ 5.509009] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 5.509159] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192 [ 5.593345] pixcir_ts 1-005c: pixcir_set_power_mode: can't read reg 0x33 : -121 [ 5.593352] pixcir_ts 1-005c: Failed to set IDLE mode [ 5.593667] pixcir_ts: probe of 1-005c failed with error -121 [ 6.101515] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.101645] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.101771] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 6.202609] omap-sham 53100000.sham: hw accel on OMAP rev 0.0 [ 6.266389] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.266508] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.266633] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 6.338256] omap-aes 53501000.aes: OMAP AES hw accel rev: 0.1 [ 6.383298] omap-aes 53501000.aes: will run requests pump with realtime priority [ 6.471443] omap-des 53701000.des: OMAP DES hw accel rev: 0.33 [ 6.509392] omap-des 53701000.des: will run requests pump with realtime priority [ 6.532368] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.532486] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.532614] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 6.539282] [drm] Initialized pvr 1.17.4948957 20110701 for 56000000.sgx on minor 0 [ 6.541322] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.541456] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.541583] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 6.800350] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.800506] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.800634] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 6.802546] PM: bootloader does not support rtc-only! [ 6.803412] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 6.803512] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 6.803625] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 7.003482] net eth0: initializing cpsw version 1.15 (0) [ 7.104361] TI DP83620 10/100 Mbps PHY 4a101000.mdio:04: attached PHY driver [TI DP83620 10/100 Mbps PHY] (mii_bus:phy_addr=4a101000.mdio:04, irq=POLL) [ 7.123363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.233461] net eth1: initializing cpsw version 1.15 (0) [ 7.334477] TI DP83620 10/100 Mbps PHY 4a101000.mdio:02: attached PHY driver [TI DP83620 10/100 Mbps PHY] (mii_bus:phy_addr=4a101000.mdio:02, irq=POLL) [ 7.336098] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 7.546170] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 7.546310] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 7.546433] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 7.887348] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 7.887483] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 7.887609] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 8.973990] EXT4-fs (mmcblk0p2): recovery complete [ 8.974016] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 8.992878] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 9.724613] EXT4-fs (mmcblk0p3): recovery complete [ 9.724637] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 9.957036] EXT4-fs (mmcblk0p4): recovery complete [ 9.957975] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) [ 9.981248] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 10.192981] device eth1 entered promiscuous mode [ 10.234021] net eth0: promiscuity not disabled as the other interface is still in promiscuity mode [ 10.234586] device eth0 entered promiscuous mode [ 10.409212] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 10.431803] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 10.492538] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 12.336842] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 12.378174] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 12.405083] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 12.438170] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 12.528836] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 12.583865] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 12.592002] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 12.604656] remoteproc remoteproc1: 54434000.pru is available [ 12.604772] pru-rproc 54434000.pru: PRU rproc node pru@54434000 probed successfully [ 12.613505] remoteproc remoteproc2: 54438000.pru is available [ 12.613612] pru-rproc 54438000.pru: PRU rproc node pru@54438000 probed successfully [ 12.614804] remoteproc remoteproc3: 54474000.pru is available [ 12.614907] pru-rproc 54474000.pru: PRU rproc node pru@54474000 probed successfully [ 12.616008] remoteproc remoteproc4: 54478000.pru is available [ 12.616108] pru-rproc 54478000.pru: PRU rproc node pru@54478000 probed successfully [ 12.695825] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 12.702788] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 12.710893] omapdss_dss 4832a000.dss: 4832a000.dss supply vdda_video not found, using dummy regulator [ 12.720368] omapdss_dss 4832a000.dss: Linked as a consumer to regulator.0 [ 12.727330] omapdss_dss 4832a000.dss: Dropping the link to regulator.0 [ 12.819160] usbcore: registered new interface driver cdc_ether modprobe: FATAL: Module g_ether not found in directory /lib/modules/4.19.160-rt69-gb3a2247aae /etc/rcS.d/S05oneStartScript.sh: line 82: printf: b7: invalid number /etc/rcS.d/S05oneStartScript.sh: line 83: printf: c5: invalid number /etc/rcS.d/S05oneStartScript.sh: line 84: printf: c7: invalid number /etc/rcS.d/S05oneStartScript.sh: line 85: printf: b0: invalid number net.ipv6.conf.default.hop_limit = 128 net.ipv6.conf.all.hop_limit = 128 net.ipv6.conf.default.autoconf = 0 net.ipv6.conf.all.forwarding = 1 net.ipv6.conf.default.forwarding = 1 sysctl: setting key "net.ipv6.conf.all.mc_forwarding" net.ipv6.conf.all.forwarding = 1 sysctl: cannot stat /proc/sys/net/ipv6/conf/wlan1/forwarding: No such file or directory pim6dd: 00:00:13.094 warning - Got 1048576 byte buffer size in 0 iterations pim6dd: 00:00:13.094 warning - setsockopt(IPV6_ROUTER_ALERT): Protocol not available pim6dd: 00:00:13.095 warning - Got 1048576 byte buffer size in 0 iterations [ 13.359223] Bluetooth: Core ver 2.22 [ 13.364673] NET: Registered protocol family 31 [ 13.369155] Bluetooth: HCI device and connection manager initialized [ 13.375584] Bluetooth: HCI socket layer initialized [ 13.380492] Bluetooth: L2CAP socket layer initialized [ 13.385667] Bluetooth: SCO socket layer initialized [ 13.410464] Bluetooth: RFCOMM TTY layer initialized [ 13.415610] Bluetooth: RFCOMM socket layer initialized [ 13.420817] Bluetooth: RFCOMM ver 1.11 *******Starting Obexdmount: /tmp/bt-inbox: can't find in /etc/fstab. . Directory /lib/modules/4.19.160-rt69-gb3a2247aae/extra exists. starting /home/root/web/webserver with 5 client OK [ 14.079162] EXT4-fs (sda2): re-mounted. Opts: (null) /etc/init.d/rc: line 56: /etc/rcS.d/S18bluez5-obexd: Permission denied Directory /lib/modules/4.19.160-rt69-gb3a2247aae/extra exists. sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory Thu Apr 29 19:10:25 UTC 2021 ALSA: Restoring mixer settings... /usr/sbin/alsactl: load_state:1735: No soundcards found... starting /home/root/web/webserver with 5 client OK Cannot open /run/boot/uboot.env: No such file or directory Error 28 fault detected [no subcode] "Address already in use" Detail: bind failed in soap_bind() mkdir: cannot create directory '/run/media': File exists mkdir: cannot create directory '/usr/share/Upgrade/Remote': File exists mkdir: cannot create directory '/usr/share/Upgrade/backup': File exists mkdir: cannot create directory '/usr/share/Upgrade/backup/App': File exists INIT: Entering runlevel: 5 Configuring network interfaces... net.ipv6.conf.lo.hop_limit = 128 net.ipv6.conf.default.keep_addr_on_down = 1 net.ipv6.conf.lo.autoconf = 0 net.ipv6.conf.all.forwarding = 1 net.ipv6.conf.default.forwarding = 1 net.ipv6.conf.default.keep_addr_on_down = 1 net.ipv6.conf.all.keep_addr_on_down = 1 net.ipv6.conf.lo.keep_addr_on_down = 1 net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory net.ipv4.ip_forward = 0 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.conf.default.send_redirects = 0 [ 17.668117] device lo entered promiscuous mode ifup: interface eth0 already configured ifup: interface eth1 already configured ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifup: ignoring unknown interface wlan1 Starting system message bus: dbus. [ 17.986749] PVR_K: UM DDK-(4948957) and KM DDK-(4948957) match. [ OK ] Loaded PowerVR consumer services. Setting environment variables...Starting UI app... UI app started. Starting OpenBSD Secure Shell server: sshd done. Starting rpcbind daemon...done. Starting Quagga daemons: zebra bgpd ripd ripngd ospfd ospf6d isisd. starting statd: done Starting advanced power management daemon: apmd. apmd[973]: apmd 3.2.1 interfacing with apm driver 1.13 and APM BIOS 1.2 Starting bluetooth: bluetoothd. Starting HOSTAP Daemon: [ 20.624787] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 20.639116] Bluetooth: BNEP filters: protocol multicast [ 20.646241] Bluetooth: BNEP socket layer initialized Configuration file: /etc/hostapd.conf [ 20.832970] cfg80211: Loading compiled-in X.509 certificates for regulatory database MESA-LOADER: failed to open kms_swrast (search paths /usr/lib/dri) failed to load driver: kms_swrast MESA-LOADER: failed to open swrast (search paths /usr/lib/dri) failed to load swrast driver Could not create GBM device (No such device) Could not open device /dev/dri/card0 - aborting! [ 21.450963] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 21.457780] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 21.474632] cfg80211: failed to load regulatory.db Could not read interface wlan0 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Could not read interface wlan0 flags: No such device nl80211 driver initialization failed. wlan0: interface state UNINITIALIZED->DISABLED wlan0: AP-DISABLED wlan0: CTRL-EVENT-TERMINATING hostapd_free_hapd_data: Interface wlan0 wasn't started exportfs: can't open /etc/exports for reading NFS daemon support not enabled in kernel Starting ntpd: done starting rsyslogd ... done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon Starting crond: OK Starting AppArmor profiles Mounting securityfs on /sys/kernel/security find: '/etc/apparmor.d/cache': No such file or directory Starting random number generator daemon Initalizing available sources Initalizing entropy source hwrng [ 33.763152] vmmcwl_fixed: disabling Enabling JITTER rng support Initalizing entropy source jitter . umount: /mnt/.psplash: not mounted. FSP Distro 2.7.4 Node0cb2b7c5c7b0 ttyS0 Warning: Use of this System is Restricted to Authorized Users This computer system is the private property of the Company and may be used only by those individuals authorized by the Company, in accordance with Company policy. Unauthorized, illegal or improper use may result in disciplinary action and/or civil or criminal prosecution. Your use of Company electronic systems is subject to monitoring and disclosure in accordance with Company policy and applicable law. By continuing to access this system, you agree that your use of Company electronic systems is subject to the foregoing and that you have no expectation of privacy in regard to any files or data stored, accessed, transmitted or received on such systems. Node0cb2b7c5c7b0 login: