U-Boot SPL 2018.01-00569-g7b4e473842-dirty (Nov 11 2019 - 20:35:47) Critical Link AM335X Dev Kit -- NAND Page size = 2048k booting from dev 8 Trying to boot from MMC1 U-Boot 2018.01-00569-g7b4e473842-dirty (Nov 11 2019 - 20:35:47 +0530) CPU : AM335X-GP rev 1.0 I2C: ready DRAM: 256 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment In: ns16550_serial Out: ns16550_serial Err: ns16550_serial HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1882 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1918 not set. Validating first E-fuse MAC HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1931 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1935 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1946 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1949 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1954 HARDIK->: func:board_late_init : file: board/cl/mitysom-335x/som.c line:1957 Net: [Manju] registered : Micrel ksz9021 [Manju] registered : Micrel ksz9031 HARDIK->: func:board_eth_init : file: board/cl/mitysom-335x/som.c line:1555 HARDIK->: func:phy_find_by_mask : file: drivers/net/phy/phy.c line:853 HARDIK->: func:search_for_existing_phy : file: drivers/net/phy/phy.c line:725 HARDIK->: func:get_phy_device_by_mask : file: drivers/net/phy/phy.c line:743 HARDIK->: func:create_phy_by_mask : file: drivers/net/phy/phy.c line:709 HARDIK->: func:get_phy_id : file: drivers/net/phy/phy.c line:682 HARDIK->: func:phy_device_create : file: drivers/net/phy/phy.c line:634 HARDIK->: func:phy_probe : file: drivers/net/phy/phy.c line:590 Srini -> Getting PHY address is success !!!! HARDIK->: func:phy_reset : file: drivers/net/phy/phy.c line:785 HARDIK->: func:phy_connect_dev : file: drivers/net/phy/phy.c line:880 [ manju ]cpsw connected to manju Micrel ksz9021 HARDIK->: func:ksz9021_config : file: drivers/net/phy/micrel_ksz90x1.c line:268 HARDIK->: func:ksz9021_config : file: drivers/net/phy/micrel_ksz90x1.c line:285 HARDIK->: func:ksz9021_config : file: drivers/net/phy/micrel_ksz90x1.c line:290 HARDIK->: func:genphy_config_aneg : file: drivers/net/phy/phy.c line:187 HARDIK->: func:genphy_config_advert : file: drivers/net/phy/phy.c line:40 HARDIK->: func:genphy_restart_aneg : file: drivers/net/phy/phy.c line:160 HARDIK->: func:genphy_restart_aneg : file: drivers/net/phy/phy.c line:160 HARDIK->: func:ksz9021_config : file: drivers/net/phy/micrel_ksz90x1.c line:298 HARDIK->: func:board_eth_init : file: board/cl/mitysom-335x/som.c line:1570 HARDIK->: get current dev name device:cpsw HARDIK->: func:board_eth_init : file: board/cl/mitysom-335x/som.c line:1584 cpsw Hit any key to stop autoboot: 2  0 => => => fatload mmc 0:1 0x88000000 am335x-mitysom-devkit.dtb => mii info PHY 0x03: OUI = 0x0885, Model = 0x21, Rev = 0x01, 100baseT, FDX => mii dump 3 0 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) => mii dump 3 0 1 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities => fatload mmc 0:1 0x88000000 am335x-mitysom-devkit.dtb 44934 bytes read in 8 ms (5.4 MiB/s) => setenv bootargs console=ttyO0,115200n8 root=/dev/mmcblk0p2 => fatload mmc 0:1 0x82000000 zImage_omap 3846656 bytes read in 292 ms (12.6 MiB/s) => bootz 0x82000000 - 0x88000000 ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800df85 ret = 0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.79-ge669d52447 (manju@manju-VirtualBox) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #1 PREEMPT Tue Nov 5 16:28:46 IST 2019 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Critical Link MitySOM-335x Devkit [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x8d000000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 197272K/262144K available (8192K kernel code, 313K rwdata, 2452K rodata, 1024K init, 263K bss, 15720K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0d4e680 ( 314 kB) [ 0.000000] .bss : 0xc0d4e680 - 0xc0d9060c ( 264 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000042] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000056] OMAP clocksource: timer1 at 24000000 Hz [ 0.000285] timer_probe: no matching timers found [ 0.000531] Console: colour dummy device 80x30 [ 0.000573] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.118878] pid_max: default: 32768 minimum: 301 [ 0.119093] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119111] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.120027] CPU: Testing write buffer coherency: ok [ 0.120105] CPU0: Spectre v2: using BPIALL workaround [ 0.120900] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.121075] Hierarchical SRCU implementation. [ 0.121483] EFI services will not be available. [ 0.123092] devtmpfs: initialized [ 0.133541] random: get_random_u32 called from bucket_table_alloc+0x8c/0x1ac with crng_init=0 [ 0.134044] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.134407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.134434] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.138607] pinctrl core: initialized pinctrl subsystem [ 0.139645] DMI not present or invalid. [ 0.140126] NET: Registered protocol family 16 [ 0.142675] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.159459] omap_hwmod: debugss: _wait_target_disable failed [ 0.188437] cpuidle: using governor ladder [ 0.188478] cpuidle: using governor menu [ 0.193723] OMAP GPIO hardware version 0.1 [ 0.205272] omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_default, deferring probe [ 0.208546] No ATAGs? [ 0.208565] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.224323] edma 49000000.edma: TI EDMA DMA engine driver [ 0.228615] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.228693] omap_i2c 4802a000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c1_pins, deferring probe [ 0.228739] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 0.229147] media: Linux media interface: v0.10 [ 0.229203] Linux video capture interface: v2.00 [ 0.229344] pps_core: LinuxPPS API ver. 1 registered [ 0.229354] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.229380] PTP clock support registered [ 0.229422] EDAC MC: Ver: 3.0.0 [ 0.229953] dmi: Firmware registration failed. [ 0.230479] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.230917] Advanced Linux Sound Architecture Driver Initialized. [ 0.232209] clocksource: Switched to clocksource timer1 [ 0.241972] NET: Registered protocol family 2 [ 0.242924] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.242966] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.242997] TCP: Hash tables configured (established 2048 bind 2048) [ 0.243120] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.243145] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.243328] NET: Registered protocol family 1 [ 0.243836] RPC: Registered named UNIX socket transport module. [ 0.243852] RPC: Registered udp transport module. [ 0.243861] RPC: Registered tcp transport module. [ 0.243869] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.244839] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.244991] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.246766] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.251751] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.252935] NFS: Registering the id_resolver key type [ 0.252994] Key type id_resolver registered [ 0.253004] Key type id_legacy registered [ 0.253056] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.255459] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.255484] io scheduler noop registered [ 0.255495] io scheduler deadline registered [ 0.255756] io scheduler cfq registered (default) [ 0.255770] io scheduler mq-deadline registered [ 0.255779] io scheduler kyber registered [ 0.257365] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.260956] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 0.320234] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.320508] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a OMAP UART0 [ 0.997561] console [ttyO0] enabled [ 1.001842] omap_uart 481a6000.serial: no wakeirq for uart3 [ 1.008016] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 31, base_baud = 3000000) is a OMAP UART3 [ 1.018230] omap_uart 481a8000.serial: no wakeirq for uart4 [ 1.024336] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 32, base_baud = 3000000) is a OMAP UART4 [ 1.035512] omap_rng 48310000.rng: Random Number Generator ver. 20 [ 1.044635] pinctrl-single 44e10800.pinmux: pin PIN40 already requested by lcd-controller@1; cannot claim for 4830e000.lcdc [ 1.056360] pinctrl-single 44e10800.pinmux: pin-40 (4830e000.lcdc) status -22 [ 1.063847] pinctrl-single 44e10800.pinmux: could not request pin 40 (PIN40) from group lcd_pins_default on device pinctrl-single [ 1.076147] tilcdc 4830e000.lcdc: Error applying setting, reverse things back [ 1.083655] tilcdc: probe of 4830e000.lcdc failed with error -22 [ 1.103323] brd: module loaded [ 1.114483] loop: module loaded [ 1.122174] m25p80 spi1.0: m25p64 (8192 Kbytes) [ 1.127209] 1 ofpart partitions found on MTD device spi1.0 [ 1.132985] Creating 1 MTD partitions on "spi1.0": [ 1.138008] 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.146421] libphy: Fixed MDIO Bus: probed [ 1.222308] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 1.230340] libphy: 4a101000.mdio: probed [ 1.236098] davinci_mdio 4a101000.mdio: phy[3]: device 4a101000.mdio:03, driver Micrel KSZ9021 Gigabit PHY [ 1.247321] cpsw 4a100000.ethernet: Detected MACID = e0:c7:9d:a6:59:3b [ 1.254413] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 1.261069] cpsw 4a100000.ethernet: ALE Table size 1024 [ 1.266694] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) [ 1.275894] i2c /dev entries driver [ 1.280114] IR NEC protocol handler initialized [ 1.284998] IR RC5(x/sz) protocol handler initialized [ 1.290286] IR RC6 protocol handler initialized [ 1.295046] IR JVC protocol handler initialized [ 1.299782] IR Sony protocol handler initialized [ 1.304625] IR SANYO protocol handler initialized [ 1.309544] IR Sharp protocol handler initialized [ 1.314476] IR MCE Keyboard/mouse protocol handler initialized [ 1.320575] IR XMP protocol handler initialized [ 1.327266] cpuidle: enable-method property 'ti,am3352' found operations [ 1.334973] sdhci: Secure Digital Host Controller Interface driver [ 1.341445] sdhci: Copyright(c) Pierre Ossman [ 1.402588] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.412695] ledtrig-cpu: registered to indicate activity on CPUs [ 1.427811] NET: Registered protocol family 10 [ 1.434079] Segment Routing with IPv6 [ 1.438005] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.445142] NET: Registered protocol family 17 [ 1.450136] Key type dns_resolver registered [ 1.454914] omap_voltage_late_init: Voltage driver support not added [ 1.468141] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 1.473741] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 1.482095] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.488918] nand: Micron MT29F2G08ABAEAWP [ 1.493211] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.501212] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 1.507061] 8 ofpart partitions found on MTD device omap2-nand.0 [ 1.513416] Creating 8 MTD partitions on "omap2-nand.0": [ 1.519013] 0x000000000000-0x000000020000 : "NAND.SPL" [ 1.525894] 0x000000020000-0x000000040000 : "NAND.SPL.backup1" [ 1.533324] 0x000000040000-0x000000060000 : "NAND.SPL.backup2" [ 1.540596] 0x000000060000-0x000000080000 : "NAND.SPL.backup3" [ 1.546813] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.555355] mmc0: new high speed SDHC card at address aaaa [ 1.562019] mmcblk0: mmc0:aaaa SS08G 7.40 GiB [ 1.568382] 0x000000080000-0x000000260000 : "NAND.u-boot" [ 1.574305] mmcblk0: p1 p2 p3 [ 1.581410] 0x000000260000-0x000000280000 : "NAND.u-boot-env" [ 1.588622] 0x000000280000-0x000000780000 : "NAND.kernel" [ 1.600027] 0x000000780000-0x000010000000 : "NAND.file-system" [ 1.843761] omap_i2c 44e0b000.i2c: bus 1 rev0.11 at 400 kHz [ 1.850822] omap_i2c 4802a000.i2c: bus 2 rev0.11 at 400 kHz [ 1.882495] tps65910 3-002d: No interrupt support, no core IRQ [ 1.890871] vrtc: supplied by vbat [ 1.898082] random: fast init done [ 1.901894] vio: supplied by vbat [ 1.906954] vdd1: supplied by vbat [ 1.912378] vdd2: supplied by vbat [ 1.919314] vdig1: supplied by vbat [ 1.924431] vdig2: supplied by vbat [ 1.929486] vpll: supplied by vbat [ 1.934517] vdac: supplied by vbat [ 1.939485] vaux1: supplied by vbat [ 1.944587] vaux2: supplied by vbat [ 1.949637] vaux33: supplied by vbat [ 1.954835] vmmc: supplied by vbat [ 1.959814] vbb: supplied by vbat [ 1.964572] omap_i2c 4819c000.i2c: bus 3 rev0.11 at 400 kHz [ 1.972657] hctosys: unable to open rtc device (rtc0) [ 1.978881] ALSA device list: [ 1.982003] No soundcards found. [ 1.990935] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem [ 2.003922] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 2.011611] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 2.044524] EXT4-fs (mmcblk0p2): recovery complete [ 2.056653] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.065426] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 2.083419] devtmpfs: mounted [ 2.088620] Freeing unused kernel memory: 1024K [ 2.445103] systemd[1]: System time before build time, advancing clock. [ 2.495228] systemd[1]: Configuration file /etc/systemd/system.conf is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.534123] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN default-hierarchy=hybrid) [ 2.557289] systemd[1]: Detected architecture arm. Welcome to Arago 2018.10! [ 2.597903] systemd[1]: Set hostname to . [ 2.911850] systemd[1]: Configuration file /lib/systemd/system/system.slice is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.933552] systemd[1]: Configuration file /lib/systemd/system/slices.target is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.953825] systemd[1]: Configuration file /lib/systemd/system/shutdown.target is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.973837] systemd[1]: Configuration file /lib/systemd/system/local-fs.target is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.001490] systemd[1]: Configuration file /lib/systemd/system/umount.target is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.023030] systemd[1]: Configuration file /lib/systemd/system/var-volatile-srv.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.045163] systemd[1]: Configuration file /lib/systemd/system/systemd-journald.socket is marked executable. Please remove executable permission bits. Proceeding anyway. [ 3.417648] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Created slice User and Session Slice. [ 3.452826] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Listening on udev Kernel Socket. [ 3.493163] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Reached target Remote File Systems. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on Process Core Dump Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on udev Control Socket. [ OK ] Created slice System Slice. [ OK ] Reached target Slices. Mounting Kernel Debug File System... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-getty.slice. Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Reached target Swap. Mounting Temporary Directory (/tmp)... [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Socket. Starting Journal Service... [ 4.271939] systemd-journald[65]: Configuration file /etc/systemd/journald.conf is marked executable. Please remove executable permission bits. Proceeding anyway. Starting File System Check on Root Device... Starting Load Kernel Modules... Starting Create list of required st…ce nodes for the current kernel... [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Temporary Directory (/tmp). [ 4.480861] cryptodev: loading out-of-tree module taints kernel. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ 4.513983] cryptodev: driver 1.9 loaded. [ OK ] Started Load Kernel Modules. Starting Apply Kernel Variables... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started File System Check on Root Device. [ OK ] Started Apply Kernel Variables. [ OK ] Started Journal Service. Starting Remount Root and Kernel File Systems... [ 4.932923] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... [ 5.200942] systemd-journald[65]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Mounting /media/ram... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Created slice system-systemd\x2dbacklight.slice. [ 7.872908] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec Starting Load/Save Screen Backlight…ightness of backlight:backlight... [[ 7.965834] omap_rtc 44e3e000.rtc: registered as rtc0 OK ] Found device /dev/ttyO0. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ 8.569769] CAN device driver interface [[ 8.652077] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=38) OK ] Started System Logging Service. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 8.847825] c_can_platform 481d0000.can: c_can_platform device registered (regs=fa1d0000, irq=39) [ 8.978973] random: crng init done [ 8.978984] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Started Kernel Logging Service. Starting RPC Bind Service... [ OK ] Started Periodic Command Scheduler. Starting telnetd.service... Starting Print notice about GPLv3 packages... [ OK ] Reached target Containers. [ OK ] Started D-Bus System Message Bus. [ 9.854300] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 10.073937] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 10.175680] omap-aes 53500000.aes: will run requests pump with realtime priority Starting Login Service... Starting Network Service... [ OK ] Started Job spooling tools. [ OK ] Started RPC Bind Service. [ OK ] Started telnetd.service. [ 11.779286] remoteproc remoteproc0: wkup_m3 is available [ 11.858989] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 11.896649] PM: Cannot get wkup_m3_ipc handle [ 12.148831] remoteproc remoteproc0: powering up wkup_m3 [ 12.193271] PM: Cannot get wkup_m3_ipc handle [ 12.360340] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 224628 [ OK ] Started Network Service. [ 12.561006] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192 [ 12.647723] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 12.763098] net eth0: initializing cpsw version 1.12 (0) [ 12.827525] EXT4-fs (mmcblk0p3): mounting ext3 file system using the ext4 subsystem [ 12.877307] EXT4-fs (mmcblk0p3): warning: mounting fs with errors, running e2fsck is recommended [ 12.895583] EXT4-fs (mmcblk0p3): recovery complete [ 12.895614] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 13.131071] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 13.713498] Micrel KSZ9021 Gigabit PHY 4a101000.mdio:03: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=4a101000.mdio:03, irq=POLL) [ 14.051041] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ OK ] Started Login Service. [ OK ] Reached target Network. Starting Permit User Sessions... Starting Network Name Resolution... Starting thttpd.service... [ OK ] Started Permit User Sessions. [ OK ] Started thttpd.service. [ 16.004152] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 16.088807] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Network Name Resolution. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started NFS status monitor for NFSv2/3 locking.. Starting rng-tools.service... [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyO0. [ OK ] Started rng-tools.service. Starting thermal-zone-init.service... [ OK ] Started thermal-zone-init.service. *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: bash binutils cifs-utils cpio dosfstools elfutils gawk gzip libdw1 libelf1 libreadline7 m4 which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ 19.587780] input: ti-tsc as /devices/platform/ocp/44e0d000.tscadc/44e0d000.tscadc:tsc/input/input0 [ 19.654567] PM: bootloader does not support rtc-only! [ 19.716999] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator [ 19.734023] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator [ 19.805149] usbcore: registered new interface driver usbfs [ 19.805230] usbcore: registered new interface driver hub [ 19.805390] usbcore: registered new device driver usb [ 19.915702] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 19.915748] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1 [ 19.947218] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 19.947231] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.947238] usb usb1: Product: MUSB HDRC host driver [ 19.947244] usb usb1: Manufacturer: Linux 4.14.79-ge669d52447 musb-hcd [ 19.947251] usb usb1: SerialNumber: musb-hdrc.0 [ 19.959168] hub 1-0:1.0: USB hub found [ 19.961648] hub 1-0:1.0: 1 port detected [ 20.060281] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 20.060320] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2 [ 20.095376] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 20.095390] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 20.095396] usb usb2: Product: MUSB HDRC host driver [ 20.095403] usb usb2: Manufacturer: Linux 4.14.79-ge669d52447 musb-hcd [ 20.095409] usb usb2: SerialNumber: musb-hdrc.1 [ 20.104748] hub 2-0:1.0: USB hub found [ 20.104852] hub 2-0:1.0: 1 port detected _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2018.10 am335x-evm ttyO0 am335x-evm login: root root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 3 Transceiver: internal Auto-negotiation: on Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes root@am335x-evm:~# ethtool eth0 - S  NIC statistics: Good Rx Frames: 0 Broadcast Rx Frames: 0 Multicast Rx Frames: 0 Pause Rx Frames: 0 Rx CRC Errors: 0 Rx Align/Code Errors: 0 Oversize Rx Frames: 0 Rx Jabbers: 0 Undersize (Short) Rx Frames: 0 Rx Fragments: 0 Rx Octets: 0 Good Tx Frames: 23 Broadcast Tx Frames: 5 Multicast Tx Frames: 18 Pause Tx Frames: 0 Deferred Tx Frames: 0 Collisions: 0 Single Collision Tx Frames: 0 Multiple Collision Tx Frames: 0 Excessive Collisions: 0 Late Collisions: 0 Tx Underrun: 0 Carrier Sense Errors: 0 Tx Octets: 3398 Rx + Tx 64 Octet Frames: 0 Rx + Tx 65-127 Octet Frames: 18 Rx + Tx 128-255 Octet Frames: 0 Rx + Tx 256-511 Octet Frames: 5 Rx + Tx 512-1023 Octet Frames: 0 Rx + Tx 1024-Up Octet Frames: 0 Net Octets: 3398 Rx Start of Frame Overruns: 0 Rx Middle of Frame Overruns: 0 Rx DMA Overruns: 0 Rx DMA chan 0: head_enqueue: 1 Rx DMA chan 0: tail_enqueue: 127 Rx DMA chan 0: pad_enqueue: 0 Rx DMA chan 0: misqueued: 0 Rx DMA chan 0: desc_alloc_fail: 0 Rx DMA chan 0: pad_alloc_fail: 0 Rx DMA chan 0: runt_receive_buf: 0 Rx DMA chan 0: runt_transmit_bu: 0 Rx DMA chan 0: empty_dequeue: 0 Rx DMA chan 0: busy_dequeue: 0 Rx DMA chan 0: good_dequeue: 0 Rx DMA chan 0: requeue: 0 Rx DMA chan 0: teardown_dequeue: 0 Tx DMA chan 0: head_enqueue: 23 Tx DMA chan 0: tail_enqueue: 0 Tx DMA chan 0: pad_enqueue: 0 Tx DMA chan 0: misqueued: 0 Tx DMA chan 0: desc_alloc_fail: 0 Tx DMA chan 0: pad_alloc_fail: 0 Tx DMA chan 0: runt_receive_buf: 0 Tx DMA chan 0: runt_transmit_bu: 0 Tx DMA chan 0: empty_dequeue: 23 Tx DMA chan 0: busy_dequeue: 0 Tx DMA chan 0: good_dequeue: 23 Tx DMA chan 0: requeue: 0 Tx DMA chan 0: teardown_dequeue: 0 root@am335x-evm:~# ifconfig eth0 eth0 Link encap:Ethernet HWaddr E0:C7:9D:A6:59:3B inet6 addr: fe80::e2c7:9dff:fea6:593b%3068585368/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:3376 (3.2 KiB) Interrupt:51 root@am335x-evm:~# uname -a Linux am335x-evm 4.14.79-ge669d52447 #1 PREEMPT Tue Nov 5 16:28:46 IST 2019 armv7l GNU/Linux root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~#