U-Boot SPL 2014.07 (Dec 01 2015 - 15:59:06) U-Boot 2014.07 (Dec 01 2015 - 15:59:06) I2C: ready DRAM: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: cpsw Hit any key to stop autoboot: 0 Tunstall:~$ Tunstall:~$ setenv autoload no Tunstall:~$ dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.82.3 Tunstall:~$ setenv serverip 192.168.82.137 Tunstall:~$ setenv netmask 255.255.255.0 Tunstall:~$ setenv gatewayip 192.168.82.1 Tunstall:~$ tftpboot ${fdtaddr} srini/tunstall-lifeline_cadb.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.82.137; our IP address is 192.168.82.3 Filename 'srini/tunstall-lifeline_cadb.dtb'. Load address: 0x88000000 Loading: ######## 1 MiB/s done Bytes transferred = 36836 (8fe4 hex) Tunstall:~$ tftpboot ${kloadaddr} srini/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.82.137; our IP address is 192.168.82.3 Filename 'srini/zImage'. Load address: 0x82000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 1.1 MiB/s done Bytes transferred = 2407376 (24bbd0 hex) Tunstall:~$ setenv bootargs console=ttyO1,115200n8 lpj=3590144 root=/dev/nfs nfsroot=192.168.82.137:/tools/rootfs_dir/srini/Rootfs rootwait ip=dhcp Tunstall:~$ bootz 0x82000000 - 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x24bbd0 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ef4d000, end 8ef58fe3 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.26 (srinivasan@tata-HP-Elite-7100-Microtower-PC) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #3 Tue Dec 1 15:21:43 IST 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Tunstall Lifeline [ 0.000000] cma: CMA: reserved 24 MiB at 8d000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO1,115200n8 lpj=3590144 root=/dev/nfs nfsroot=192.168.82.137:/tools/rootfs_dir/srini/Rootfs rootwait ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 229096K/261120K available (3751K kernel code, 214K rwdata, 652K rodata, 182K init, 162K bss, 32024K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0454f84 (4404 kB) [ 0.000000] .init : 0xc0455000 - 0xc0482a80 ( 183 kB) [ 0.000000] .data : 0xc0484000 - 0xc04b9960 ( 215 kB) [ 0.000000] .bss : 0xc04b9960 - 0xc04e2204 ( 163 kB) [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000028] OMAP clocksource: timer1 at 24000000 Hz [ 0.000256] Console: colour dummy device 80x30 [ 0.000277] Calibrating delay loop (skipped) preset value.. 718.02 BogoMIPS (lpj=3590144) [ 0.000291] pid_max: default: 32768 minimum: 301 [ 0.000369] Security Framework initialized [ 0.000416] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000426] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.007256] CPU: Testing write buffer coherency: ok [ 0.007585] Setting up static identity map for 0x803af4f0 - 0x803af548 [ 0.008424] devtmpfs: initialized [ 0.009887] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.015574] omap_hwmod: tptc0 using broken dt data from edma [ 0.015638] omap_hwmod: tptc1 using broken dt data from edma [ 0.015696] omap_hwmod: tptc2 using broken dt data from edma [ 0.019045] omap_hwmod: debugss: _wait_target_disable failed [ 0.062100] pinctrl core: initialized pinctrl subsystem [ 0.062961] regulator-dummy: no parameters [ 0.064990] NET: Registered protocol family 16 [ 0.066641] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.068161] cpuidle: using governor ladder [ 0.068176] cpuidle: using governor menu [ 0.073463] syscon 44e10000.control_module: regmap [mem 0x44e10000-0x44e107fb] registered [ 0.074676] platform 49000000.edma: alias fck already exists [ 0.074697] platform 49000000.edma: alias fck already exists [ 0.074709] platform 49000000.edma: alias fck already exists [ 0.075643] OMAP GPIO hardware version 0.1 [ 0.089335] No ATAGs? [ 0.089356] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.102416] bio: create slab at 0 [ 0.114487] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.115190] entering enablinggggggggggggggg enable-active-highhhhhhhhhhhhh [ 0.115200] -------HIGHHHHHHHHHHHHHHHHH not at boot [ 0.115548] wlan-en-regulator: 1800 mV [ 0.115696] -------LOWWWWWWWWWWWWWWWWWWWWW not at boot [ 0.115951] vmmcsd_fixed: 3300 mV [ 0.117405] SCSI subsystem initialized [ 0.118184] usbcore: registered new interface driver usbfs [ 0.118340] usbcore: registered new interface driver hub [ 0.118519] usbcore: registered new device driver usb [ 0.119213] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.119237] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.119651] pps_core: LinuxPPS API ver. 1 registered [ 0.119662] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.119777] PTP clock support registered [ 0.121453] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.122379] Advanced Linux Sound Architecture Driver Initialized. [ 0.123302] Switched to clocksource timer1 [ 0.140029] NET: Registered protocol family 2 [ 0.140778] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.140806] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.140829] TCP: Hash tables configured (established 2048 bind 2048) [ 0.140888] TCP: reno registered [ 0.140899] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.140914] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.141062] NET: Registered protocol family 1 [ 0.141404] RPC: Registered named UNIX socket transport module. [ 0.141413] RPC: Registered udp transport module. [ 0.141418] RPC: Registered tcp transport module. [ 0.141424] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.142151] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.144556] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.146004] VFS: Disk quotas dquot_6.5.2 [ 0.146056] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.146477] msgmni has been set to 495 [ 0.147959] NET: Registered protocol family 38 [ 0.147997] io scheduler noop registered [ 0.148017] io scheduler cfq registered (default) [ 0.149520] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.150318] [ 0.150318] Device Registered: pinctrl [ 0.150332] Major number = 249, Minor number = 0 [ 0.153070] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.153204] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 0.153912] omap_uart 48022000.serial: no wakeirq for uart0 [ 0.154024] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 0.789163] console [ttyO1] enabled [ 0.793358] omap_uart 481a8000.serial: no wakeirq for uart0 [ 0.799253] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4 [ 0.809425] omap_uart 481aa000.serial: no wakeirq for uart0 [ 0.815396] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62, base_baud = 3000000) is a OMAP UART5 [ 0.826205] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 0.835206] PPP generic driver version 2.4.2 [ 0.840228] usbcore: registered new interface driver cdc_ether [ 0.846506] usbcore: registered new interface driver cdc_eem [ 0.852542] usbcore: registered new interface driver rndis_host [ 0.858838] usbcore: registered new interface driver cdc_subset [ 0.865215] usbcore: registered new interface driver cdc_ncm [ 0.871492] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.878314] ehci-omap: OMAP-EHCI Host Controller driver [ 0.884192] usbcore: registered new interface driver cdc_wdm [ 0.890280] usbcore: registered new interface driver usb-storage [ 0.897681] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 0.905373] i2c /dev entries driver [ 0.910808] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 0.953893] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz [ 0.964683] omap_hsmmc 48060000.mmc: card claims to support voltages below defined range [ 0.985248] mmc0: queuing unknown CIS tuple 0x91 (3 bytes) [ 0.992473] mmc0: new high speed SDIO card at address 0001 [ 1.001225] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz [ 1.013165] ledtrig-cpu: registered to indicate activity on CPUs [ 1.019879] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.027281] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.034529] platform 44d00000.wkup_m3: Driver wkup_m3 requests probe deferral [ 1.064200] davinci_evm sound.18: uda134x-hifi <-> 48038000.mcasp mapping ok [ 1.074890] TCP: cubic registered [ 1.078338] Initializing XFRM netlink socket [ 1.082793] NET: Registered protocol family 17 [ 1.087603] NET: Registered protocol family 15 [ 1.092301] Key type dns_resolver registered [ 1.097463] cpu cpu0: of_pm_voltdm_notifier_register: Failed to get cpu0 regulator/voltdm: -517 [ 1.106621] cpu cpu0: cpu0 clock notifier not ready, retry [ 1.112350] mmc1: BKOPS_EN bit is not set [ 1.116631] platform cpufreq-cpu0.0: Driver cpufreq-cpu0 requests probe deferral [ 1.125020] PM: bootloader does not support rtc-only! [ 1.130377] ThumbEE CPU extension supported. [ 1.134956] Registering SWP/SWPB emulation handler [ 1.141009] wlan-en-regulator: disabling [ 1.145273] regulator-dummy: disabling [ 1.149244] mmc1: new high speed MMC card at address 0001 [ 1.156502] mmcblk0: mmc1:0001 MMC02G 1.78 GiB [ 1.161502] mmcblk0boot0: mmc1:0001 MMC02G partition 1 1.00 MiB [ 1.168953] mmcblk0boot1: mmc1:0001 MMC02G partition 2 1.00 MiB [ 1.175560] DCDC1: at 1500 mV [ 1.180608] vdd_mpu: 925 <--> 1375 mV at 1325 mV [ 1.186905] vdd_core: 925 <--> 1150 mV at 1125 mV [ 1.191970] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 > [ 1.198755] LDO1: at 1800 mV [ 1.203083] LDO2: at 3300 mV [ 1.207778] mmcblk0boot1: unknown partition table [ 1.213261] LDO3: 1800 mV [ 1.217726] LDO4: at 3300 mV [ 1.220920] mmcblk0boot0: unknown partition table [ 1.227263] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 1.233724] lm75 0-0048: hwmon0: sensor 'tcn75' [ 1.238832] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.245075] remoteproc0: wkup_m3 is available [ 1.249700] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 1.259055] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 1.269950] remoteproc0: Direct firmware load failed with error -2 [ 1.276490] remoteproc0: Falling back to user helper [ 1.282188] cpu cpu0: of_pm_voltdm_notifier_register: Fail calculating voltage latency[950000<->950000]:-22 [ 1.353392] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 1.359812] davinci_mdio 4a101000.mdio: detected phy mask fffffffd [ 1.367676] libphy: 4a101000.mdio: probed [ 1.371914] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver DP83848 PHY [ 1.382144] cpsw 4a100000.ethernet: Detected MACID = 68:c9:0b:6d:0d:bd [ 1.395175] input: gpio_buttons.19 as /devices/gpio_buttons.19/input/input0 [ 1.404502] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.420925] net eth0: initializing cpsw version 1.12 (0) [ 1.503966] net eth0: phy found : id is : 0x20005c90 [ 1.509301] net eth0: PHY already attached [ 1.513654] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 3.504027] libphy: 4a101000.mdio:01 - Link is Up - 100/Full [ 3.543369] Sending DHCP requests ., OK [ 3.563829] IP-Config: Got DHCP answer from 192.168.82.1, my address is 192.168.82.3 [ 3.572423] IP-Config: Complete: [ 3.575896] device=eth0, hwaddr=68:c9:0b:6d:0d:bd, ipaddr=192.168.82.3, mask=255.255.255.0, gw=192.168.82.1 [ 3.586604] host=192.168.82.3, domain=, nis-domain=(none) [ 3.592734] bootserver=0.0.0.0, rootserver=192.168.82.137, rootpath= [ 3.599700] nameserver0=10.1.1.2, nameserver1=10.1.1.3 [ 3.606025] ALSA device list: [ 3.609148] #0: TI UDA1345TS [ 3.622391] VFS: Mounted root (nfs filesystem) readonly on device 0:13. [ 3.630251] devtmpfs: mounted [ 3.634204] Freeing unused kernel memory: 180K (c0455000 - c0482000) INIT: version 2.88 booting UIM SYSFS Node Not Found Starting ifplugd service for dynamic IP assignment... Starting udev mkdir: can't create directory '/var/lib/dbus': Read-only file system chown: /var/lib/dbus: No such file or directory chgrp: /var/lib/dbus: No such file or directory [ 5.798657] random: dbus-uuidgen urandom read with 126 bits of entropy available Failed to open "/etc/machine-id": No such file or directory Starting system message bus: [ 5.907355] random: nonblocking pool is initialized Failed to start message bus: Failed to read directory "/etc/dbus-1/system.d": No such file or directory dbus. [ 6.246064] udevd[657]: starting version 182 TUNSTALL INIT CONFIGURATIONS START GSM_PWR_ON_3V3 GSM_reset Configure PIN 50 as PWM PIN ################################################################# Running ntpdate to fetch current date and time from NTP server ################################################################## ALSA: Restoring mixer settings... Got NTP server, IP: 192.168.82.40 GPIO pin =50 GPIO register data =0x6[ 6.548515] GPIO 50 PHY address =0x44e10848 PWM LED CONFIGURATION Vamp_C1 Configuration Vamp_C2 Configuration Stereo codec Configuration Audio amplifier Configuration BATT_ON Monocodec driver configuration WIFI DRIVER LOADINGGGGGGGGGGGGG TUNSTALL INIT CONFIGURATIONS END Programming MAX9860 Registers /usr/sbin/alsactl: state_lock:121: file /var/lib/alsa/asound.state lock error: File exists /usr/sbin/alsactl: load_state:1677: Cannot open /var/lib/alsa/asound.state for reading: File exists Found hardware: "TI_UDA1345TS" "" "" "" "" Hardware is initialized using a generic method Simple mixer control 'Master',0 Capabilities: pvolume pvolume-joined Playback channels: Mono Limits: Playback 0 - 63 Mono: Playback 63 [100%] Simple mixer control 'DC Filter Enable',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] urandom start: failed. [ 8.364772] 47401300.usb-phy supply vcc not found, using dummy regulator [ 8.538317] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 8.883750] remoteproc0: powering up wkup_m3 [ 8.944508] remoteproc0: Booting fw image am335x-pm-firmware.elf, size 154420 [ 8.952734] PM: CM3 Firmware Version = 0x190 [ 9.198214] remoteproc0: remote processor wkup_m3 is now up [ 9.563830] Loading modules backported from Linux version R8.5-0-gcb51164 [ 9.570985] Backport generated by backports.git R8.4-0-g0d46f43 [ 10.045974] ENTERING INTO WLCORE_PROBE_OFFFFF [ 10.093180] PRINTING IRQQQQQQQQ NUMBEEEEEERR 150 [ 14.177944] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 14.304242] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 14.423850] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 14.431015] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 14.438662] usb usb1: Product: MUSB HDRC host driver [ 14.443914] usb usb1: Manufacturer: Linux 3.14.26 musb-hcd [ 14.449681] usb usb1: SerialNumber: musb-hdrc.1.auto [ 14.928190] hub 1-0:1.0: USB hub found 1 Jan 00:00:14 ntpdate[662]: no server suitable for synchronization found [ 15.038091] hub 1-0:1.0: 1 port detected [ 16.078040] cfg80211: Calling CRDA to update world regulatory domain [ 17.217088] ENTERING INTO WLCOREEEEEEEEEE_PROBEEEEEEEEEE [ 17.342848] Entering wlcore_nvs_cb.............. [ 17.383443] before ENTERING request_threaded_irqQQQQQQQQQQ [ 17.467344] AFTERrrrrrrrrrrrr REQUEST_IRQQQQQQ [ 17.542982] cfg80211: World regulatory domain updated: [ 17.548576] cfg80211: DFS Master region: unset [ 17.553158] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 17.563549] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.571956] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.580392] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 17.588831] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 17.598817] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 17.608798] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 17.617322] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 17.625755] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 17.953732] wlcore: wl18xx HW: 183xH, PG 1.3 (ROM 0x8) [ 18.053927] ENTERING INTO wl12xx_sdio_power_offffffffffff [ 18.087117] mmc0: mmc_power_save_host: powering down [ 18.141606] case 1 WLAN CHIP IDDDDDDDDDDD chip id 0x6030111 (185x PG20) [ 18.241579] wlcore: loaded [ 18.294529] wlcore: driver version: R8.5-dirty [ 18.299345] wlcore: compilation time: Tue Dec 1 20:39:46 2015 [ 19.780734] EXT4-fs (mmcblk0boot0): mounted filesystem without journal. Opts: (null) [ 20.077116] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) Sat Jan 1 00:06:00 UTC 2000 INIT: Entering runlevel: 5 Starting syslogd/klogd: [ 21.383016] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null) done lifeline login: 1 Jan 00:00:23 ntpdate[977]: no server suitable for synchronization found 1 Jan 00:00:31 ntpdate[1238]: no server suitable for synchronization found Failed to set ntpdate after 3 re-tries!!! lifeline login: root root@lifeline:~# cd / root@lifeline:/# cat /proc/interrupts CPU0 28: 853 INTC 12 edma 30: 6 INTC 14 edma_error 32: 0 INTC 16 TI-am335x-adc 33: 0 INTC 17 47400000.dma-controller 34: 0 INTC 18 musb-hdrc.1.auto 44: 2587 INTC 28 mmc1 56: 0 INTC 40 4a100000.ethernet 57: 17831 INTC 41 4a100000.ethernet 58: 6447 INTC 42 4a100000.ethernet 59: 0 INTC 43 4a100000.ethernet 80: 312 INTC 64 mmc0 84: 2579 INTC 68 gp_timer 86: 199 INTC 70 44e0b000.i2c 89: 203 INTC 73 OMAP UART1 91: 0 INTC 75 rtc0 92: 0 INTC 76 rtc0 93: 0 INTC 77 wkup_m3 94: 1 INTC 78 wkup_m3_txev 125: 0 INTC 109 53100000.sham 127: 0 INTC 111 48310000.rng 147: 0 44e07000.gpio 3 mains_v 148: 0 44e07000.gpio 4 rech_batt_v_low 149: 1 44e07000.gpio 5 rech_batt_v_high 150: 0 44e07000.gpio 6 wl18xx 156: 0 44e07000.gpio 12 uart5_pots_rx 157: 0 44e07000.gpio 13 h_wire 163: 0 44e07000.gpio 19 smartrf_rx 166: 1 44e07000.gpio 22 Alarm_key 167: 1 44e07000.gpio 23 Away_key 170: 1 44e07000.gpio 26 Cancel_key 253: 1 481ae000.gpio 13 gsmaudio_switch Err: 0 root@lifeline:~# root@lifeline:~# root@lifeline:~# cd / root@lifeline:/# root@lifeline:/# lsmod Module Size Used by wl18xx 63336 0 wlcore 134956 1 wl18xx mac80211 238656 2 wl18xx,wlcore cfg80211 135616 3 mac80211,wl18xx,wlcore musb_dsps 5668 0 musb_hdrc 42512 1 musb_dsps wlcore_sdio 3616 0 compat 1040 4 cfg80211,mac80211,wl18xx,wlcore_sdio musb_am335x 872 0 root@lifeline:/# 1 Jan 00:00:32 ntpdate[1246]: no server suitable for synchronization found Failed to set ntpdate after 3 re-tries!!! root@lifeline:/# root@lifeline:/# root@lifeline:/# ifconfig wlan0 up [ 56.761970] wlcore: ERROR timeout waiting for the hardware to complete initialization [ 56.816330] mmc0: mmc_power_save_host: powering down [ 71.629236] wlcore: ERROR timeout waiting for the hardware to complete initialization [ 71.683547] mmc0: mmc_power_save_host: powering down