U-Boot SPL 2021.01-dirty (Dec 10 2021 - 10:20:26 +0800)
SYSFW ABI: 3.1 (firmware rev 0x0015 '21.5.0--v2021.05 (Terrific Llam')
Reading on-board EEPROM at 0x50 failed 1
SPL initial stack usage: 1432 bytes
Trying to boot from MMC2
Starting ATF on ARM64 core...

NOTICE:  BL31: v2.5(release):08.00.00.004-dirty
NOTICE:  BL31: Built : 14:11:00, Aug  7 2021

U-Boot SPL 2021.01-dirty (Dec 10 2021 - 10:19:14 +0800)
SYSFW ABI: 3.1 (firmware rev 0x0015 '21.5.0--v2021.05 (Terrific Llam')
Reading on-board EEPROM at 0x50 failed 1
Detected: Silicon SR2.0
Trying to boot from MMC2
sdhci@4fa0000 mmc_init call mmc_start_init
sdhci@4fa0000 mmc_init call mmc_complete_init


U-Boot 2021.01-dirty (Dec 10 2021 - 10:19:14 +0800)

SoC:   AM65X SR2.0
Model: Texas Instruments AM654 Base Board
Reading on-board EEPROM at 0x50 failed 1
Board: AM6-COMPROCEVM rev E3
DRAM:  1 GiB
MMC:   sdhci@4f80000: 0, sdhci@4fa0000: 1
Loading Environment from MMC... sdhci@4f80000 mmc_init call mmc_start_init
*** mmc_go_idle ***
*** mmc_send_if_cond ***
(2702) sdhci@4f80000 mmc_send_if_cond = -110 cmd=8
sdhci@4f80000 mmc_get_op_cond call mmc_send_op_cond
*** mmc_send_op_cond ***
*** mmc_go_idle ***
*** mmc_send_op_cond_iter ***
*** mmc_send_op_cond_iter cmdarg=0, voltage=3539072 ***
mmc_send_op_cond_iter err=-110!
sdhci@4f80000 mmc_send_op_cond err=-110!
Card did not respond to voltage select! : -110
mmc_init: -95, time 57
*** Warning - No block device, using default environment

In:    serial
Out:   serial
Err:   serial
Reading on-board EEPROM at 0x50 failed 1
Detected: Silicon SR2.0
ax58100_rst_control value=0
ax58100_phy_rst value=0
ecat2_phy_rst value=0
eth0_phy_rst value=0
eth1_phy_rst value=0
Net:   am65_cpsw_nuss_slave ethernet@46000000: K3 CPSW: nuss_ver: 0x6BA00102 cpsw_ver: 0x6BA80102 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000
eth0: ethernet@46000000
Hit any key to stop autoboot:  0
=> mmc info
sdhci@4f80000 mmc_init call mmc_start_init
*** mmc_go_idle ***
*** mmc_send_if_cond ***
(2702) sdhci@4f80000 mmc_send_if_cond = -110 cmd=8
sdhci@4f80000 mmc_get_op_cond call mmc_send_op_cond
*** mmc_send_op_cond ***
*** mmc_go_idle ***
*** mmc_send_op_cond_iter ***
*** mmc_send_op_cond_iter cmdarg=0, voltage=3539072 ***
mmc_send_op_cond_iter err=-110!
sdhci@4f80000 mmc_send_op_cond err=-110!
Card did not respond to voltage select! : -110
mmc_init: -95, time 57
=> mmc rescan
sdhci@4f80000 mmc_init call mmc_start_init
*** mmc_go_idle ***
*** mmc_send_if_cond ***
(2702) sdhci@4f80000 mmc_send_if_cond = -110 cmd=8
sdhci@4f80000 mmc_get_op_cond call mmc_send_op_cond
*** mmc_send_op_cond ***
*** mmc_go_idle ***
*** mmc_send_op_cond_iter ***
*** mmc_send_op_cond_iter cmdarg=0, voltage=3539072 ***
mmc_send_op_cond_iter err=-110!
sdhci@4f80000 mmc_send_op_cond err=-110!
Card did not respond to voltage select! : -110
mmc_init: -95, time 56
=>