Loading ARM Linux zImage '/mnt/tftp/zImage' Loading devicetree from '/mnt/tftp/am335x-phycore-rdk.dtb' commandline: console=ttyO0,115200n8 consoleblank=0 ip=192.168.1.94:192.168.1.68:192.168.1.1:255.255.255.0::eth0: root=/dev/nfs nfsroot=/home/bhaskar/work/wifi/rootfs,vers=3,udp rw [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.12.30-dirty (bhaskar@phytec) (gcc version 4.7.3 20121106 (prerelease) (OSELAS.Toolchain-2012.12. 1 linaro-4.7-2012.11) ) #3 SMP Wed Jul 8 12:11:25 IST 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: Phytec AM335x PCM-953 [ 0.000000] cma: CMA: reserved 24 MiB at 9e000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0d4d000 s9024 r8192 d15552 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129280 [ 0.000000] Kernel command line: console=ttyO0,115200n8 consoleblank=0 ip=192.168.1.94:192.168.1.68:192.168.1.1:255.255.255. 0::eth0: root=/dev/nfs nfsroot=/home/bhaskar/work/wifi/rootfs,vers=3,udp rw [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 482484K/521216K available (6107K kernel code, 579K rwdata, 2052K rodata, 396K init, 258K bss, 38732K res erved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0800064 (8161 kB) [ 0.000000] .init : 0xc0801000 - 0xc0864340 ( 397 kB) [ 0.000000] .data : 0xc0866000 - 0xc08f6f88 ( 580 kB) [ 0.000000] .bss : 0xc08f6f90 - 0xc0937b24 ( 259 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 25000000 Hz [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] OMAP clocksource: timer1 at 25000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000444] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656) [ 0.049607] pid_max: default: 32768 minimum: 301 [ 0.049781] Security Framework initialized [ 0.049869] Mount-cache hash table entries: 512 [ 0.064797] Initializing cgroup subsys debug [ 0.064834] Initializing cgroup subsys devices [ 0.064850] Initializing cgroup subsys perf_event [ 0.064930] CPU: Testing write buffer coherency: ok [ 0.065444] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.065520] Setting up static identity map for 0xc05fc7d8 - 0xc05fc848 [ 0.066596] Brought up 1 CPUs [ 0.066614] SMP: Total of 1 processors activated. [ 0.066626] CPU: All CPU(s) started in SVC mode. [ 0.067537] devtmpfs: initialized [ 0.073388] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.141937] omap_hwmod: debugss: _wait_target_disable failed [ 0.142962] pinctrl core: initialized pinctrl subsystem [ 0.144313] regulator-dummy: no parameters [ 0.147214] NET: Registered protocol family 16 [ 0.150713] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.155219] cpuidle: using governor ladder [ 0.155244] cpuidle: using governor menu [ 0.166614] platform mpu.2: FIXME: clock-name 'fck' DOES NOT exist in dt! [ 0.168377] platform 49000000.edma: FIXME: clock-name 'fck' DOES NOT exist in dt! [ 0.170509] OMAP GPIO hardware version 0.1 [ 0.186914] omap-gpmc 50000000.gpmc: could not find pctldev for node /pinmux@44e10800/pinmux_nandflash, deferring probe [ 0.186961] platform 50000000.gpmc: Driver omap-gpmc requests probe deferral [ 0.187604] platform 56000000.sgx: FIXME: clock-name 'fck' DOES NOT exist in dt! [ 0.192940] DSS not supported on this SoC [ 0.192966] No ATAGs? [ 0.192982] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.195746] cpsw.1: No hwaddr in dt. Using d0:ff:50:0b:0c:a9 from efuse [ 0.243152] bio: create slab at 0 [ 0.269239] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.341364] wlan-en-regulator: 1800 mV [ 0.342344] vcc3v3: 3300 mV [ 0.342916] lcd_3v3: 3300 mV [ 0.349080] SCSI subsystem initialized [ 0.351486] usbcore: registered new interface driver usbfs [ 0.351782] usbcore: registered new interface driver hub [ 0.352144] usbcore: registered new device driver usb [ 0.353741] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0, deferring probe [ 0.353779] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.354218] media: Linux media interface: v0.10 [ 0.354516] Linux video capture interface: v2.00 [ 0.354983] pps_core: LinuxPPS API ver. 1 registered [ 0.354998] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.355224] PTP clock support registered [ 0.360270] Switched to clocksource timer1 [ 0.393992] NET: Registered protocol family 2 [ 0.395339] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.395451] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.395549] TCP: Hash tables configured (established 4096 bind 4096) [ 0.395639] TCP: reno registered [ 0.395660] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.395693] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.396025] NET: Registered protocol family 1 [ 0.396566] RPC: Registered named UNIX socket transport module. [ 0.396583] RPC: Registered udp transport module. [ 0.396594] RPC: Registered tcp transport module. [ 0.396605] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.397133] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.397300] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.398395] PM: Loading am335x-pm-firmware.bin [ 0.602242] VFS: Disk quotas dquot_6.5.2 [ 0.602464] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.603515] NFS: Registering the id_resolver key type [ 0.603616] Key type id_resolver registered [ 0.603633] Key type id_legacy registered [ 0.603692] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. [ 0.603947] msgmni has been set to 990 [ 0.606786] NET: Registered protocol family 38 [ 0.606852] io scheduler noop registered [ 0.606866] io scheduler deadline registered [ 0.606901] io scheduler cfq registered (default) [ 0.610062] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.622181] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.626414] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.316324] console [ttyO0] enabled [ 1.321329] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 1.332465] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3 [ 1.345148] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.352956] [drm] Initialized drm 1.1.0 20060810 [ 1.376257] brd: module loaded [ 1.389176] loop: module loaded [ 1.399436] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.409654] edma-dma-engine edma-dma-engine.0: allocated channel for 0:17 [ 1.417335] edma-dma-engine edma-dma-engine.0: allocated channel for 0:16 [ 1.425294] m25p80 spi1.0: found s25sl064p, expected m25p80 [ 1.431368] m25p80 spi1.0: s25sl064p (8192 Kbytes) [ 1.436462] 5 ofpart partitions found on MTD device spi1.0 [ 1.442282] Creating 5 MTD partitions on "spi1.0": [ 1.447351] 0x000000000000-0x000000020000 : "xload" [ 1.455003] 0x000000020000-0x0000000a0000 : "barebox" [ 1.462744] 0x0000000a0000-0x0000000c0000 : "bareboxenv" [ 1.470674] 0x0000000c0000-0x0000000e0000 : "oftree" [ 1.478111] 0x0000000e0000-0x000000800000 : "kernel" [ 1.492176] CAN device driver interface [ 1.498227] c_can_platform 481d0000.d_can: c_can_platform device registered (regs=fa1d0000, irq=71) [ 1.511614] usbcore: registered new interface driver asix [ 1.517644] usbcore: registered new interface driver ax88179_178a [ 1.524592] usbcore: registered new interface driver cdc_ether [ 1.531221] usbcore: registered new interface driver r815x [ 1.537308] usbcore: registered new interface driver smsc95xx [ 1.543673] usbcore: registered new interface driver net1080 [ 1.549899] usbcore: registered new interface driver cdc_subset [ 1.556456] usbcore: registered new interface driver zaurus [ 1.562853] usbcore: registered new interface driver cdc_ncm [ 1.569579] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.576562] ehci-pci: EHCI PCI platform driver [ 1.581892] usbcore: registered new interface driver cdc_wdm [ 1.588171] usbcore: registered new interface driver usb-storage [ 1.600193] musb-hdrc musb-hdrc.0.auto: Enabled SW babble control [ 1.607128] musb-hdrc musb-hdrc.0.auto: Falied to request rx1. [ 1.613534] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517 [ 1.621830] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral [ 1.632553] musb-hdrc musb-hdrc.1.auto: Enabled SW babble control [ 1.639117] musb-hdrc musb-hdrc.1.auto: Falied to request rx1. [ 1.645511] musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517 [ 1.653798] platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral [ 1.685808] mousedev: PS/2 mouse device common for all mice [ 1.697636] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc1 [ 1.705665] 44e3e000.rtc: already running [ 1.712274] i2c /dev entries driver [ 1.716908] Driver for 1-wire Dallas network protocol. [ 1.726800] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.737132] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 1.744734] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 1.868284] ledtrig-cpu: registered to indicate activity on CPUs [ 1.875282] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 1.882640] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.891088] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.897214] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 1.904596] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 1.914068] usbcore: registered new interface driver usbhid [ 1.919933] usbhid: USB HID core driver [ 1.928853] oprofile: using arm/armv7 [ 1.933326] TCP: cubic registered [ 1.936821] Initializing XFRM netlink socket [ 1.941665] NET: Registered protocol family 17 [ 1.946402] NET: Registered protocol family 15 [ 1.951146] can: controller area network core (rev 20120528 abi 9) [ 1.957787] NET: Registered protocol family 29 [ 1.962751] 8021q: 802.1Q VLAN Support v1.8 [ 1.967315] Key type dns_resolver registered [ 1.972809] cpu cpu0: cpu0 regulator not ready, retry [ 1.978156] platform cpufreq-cpu0.0: Driver cpufreq-cpu0 requests probe deferral [ 1.986604] PM: CM3 Firmware Version = 0x186 [ 1.991781] ThumbEE CPU extension supported. [ 1.996333] Registering SWP/SWPB emulation handler [ 2.003590] vcc3v3: disabling [ 2.006740] wlan-en-regulator: disabling [ 2.011021] regulator-dummy: disabling [ 2.016134] Error: Driver 'tfp410' is already registered, aborting... [ 2.026876] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.033994] [drm] No driver support for vblank timestamp query. [ 2.088561] Console: switching to colour frame buffer device 100x30 [ 2.102194] tilcdc 4830e000.lcdc: fb0: frame buffer device [ 2.108077] tilcdc 4830e000.lcdc: registered panic notifier [ 2.113999] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 2.121218] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 2.126659] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 2.134551] ONFI param page 0 valid [ 2.138235] ONFI flash detected [ 2.141648] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAH4), 512MiB, page size: 2048, OOB size: 64 [ 2.153646] omap2-nand: detected x8 NAND flash [ 2.158318] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.163976] omap2-nand: using custom ecc layout [ 2.168957] 9 ofpart partitions found on MTD device omap2-nand.0 [ 2.175362] Creating 9 MTD partitions on "omap2-nand.0": [ 2.181008] 0x000000000000-0x000000020000 : "xload" [ 2.188767] 0x000000020000-0x000000040000 : "xload_backup1" [ 2.197232] 0x000000040000-0x000000060000 : "xload_backup2" [ 2.205674] 0x000000060000-0x000000080000 : "xload_backup3" [ 2.214241] 0x000000080000-0x000000100000 : "barebox" [ 2.222609] 0x000000100000-0x000000140000 : "bareboxenv" [ 2.230926] 0x000000140000-0x000000180000 : "oftree" [ 2.238716] 0x000000180000-0x000000980000 : "kernel" [ 2.253170] 0x000000980000-0x000020000000 : "root" [ 2.684667] tps65910 0-002d: No interrupt support, no core IRQ [ 2.693833] vrtc: 1800 mV [ 2.697027] vrtc: supplied by wlan-en-regulator [ 2.774133] vio: at 1500 mV [ 2.777306] vio: supplied by wlan-en-regulator [ 2.784351] vdd_mpu: 912 <--> 1375 mV at 1287 mV [ 2.789404] vdd_mpu: supplied by wlan-en-regulator [ 2.796756] vdd_core: 912 <--> 1150 mV at 1100 mV [ 2.802003] vdd_core: supplied by wlan-en-regulator [ 2.808399] vdd3: 5000 mV [ 2.813020] vdig1_1p8v: 1800 mV [ 2.816520] vdig1_1p8v: supplied by wlan-en-regulator [ 2.823611] vdig2: at 1800 mV [ 2.826926] vdig2: supplied by wlan-en-regulator [ 2.833545] vpll: at 1800 mV [ 2.836759] vpll: supplied by wlan-en-regulator [ 2.843403] vdac: at 1800 mV [ 2.846639] vdac: supplied by wlan-en-regulator [ 2.853199] vaux1: at 1800 mV [ 2.856523] vaux1: supplied by wlan-en-regulator [ 2.863138] vaux2: at 3300 mV [ 2.866451] vaux2: supplied by wlan-en-regulator [ 2.873086] vaux33: at 3300 mV [ 2.876498] vaux33: supplied by wlan-en-regulator [ 2.883224] vmmc: at 3300 mV [ 2.886458] vmmc: supplied by wlan-en-regulator [ 2.893167] tps65910-rtc tps65910-rtc: IRQ is not free. [ 2.898698] tps65910-rtc: probe of tps65910-rtc failed with error -22 [ 2.907110] at24 0-0052: 4096 byte 24c32 EEPROM, writable, 32 bytes/write [ 2.915316] rtc-m41t80 0-0068: chip found, driver version 0.05 [ 2.922629] rtc-m41t80 0-0068: rtc core: registered rv4162c7 as rtc0 [ 2.930989] edt_ft5x06 0-0038: touchscreen probe failed [ 2.936547] edt_ft5x06: probe of 0-0038 failed with error -121 [ 2.943035] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.949542] musb-hdrc musb-hdrc.0.auto: Enabled SW babble control [ 2.958874] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 2.965745] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1 [ 2.974445] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.981662] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.989262] usb usb1: Product: MUSB HDRC host driver [ 2.994511] usb usb1: Manufacturer: Linux 3.12.30-dirty musb-hcd [ 3.000857] usb usb1: SerialNumber: musb-hdrc.0.auto [ 3.007524] hub 1-0:1.0: USB hub found [ 3.011670] hub 1-0:1.0: 1 port detected [ 3.017480] musb-hdrc musb-hdrc.1.auto: Enabled SW babble control [ 3.026855] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 3.033657] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 2 [ 3.042461] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.049620] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.057312] usb usb2: Product: MUSB HDRC host driver [ 3.062586] usb usb2: Manufacturer: Linux 3.12.30-dirty musb-hcd [ 3.068909] usb usb2: SerialNumber: musb-hdrc.1.auto [ 3.075594] hub 2-0:1.0: USB hub found [ 3.079642] hub 2-0:1.0: 1 port detected [ 3.130357] tilcdc 4830e000.lcdc: timeout waiting for framedone [ 3.230369] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.236784] davinci_mdio 4a101000.mdio: detected phy mask fffffffa [ 3.245034] libphy: 4a101000.mdio: probed [ 3.249256] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.258894] davinci_mdio 4a101000.mdio: phy[2]: device 4a101000.mdio:02, driver Micrel KSZ9021 Gigabit PHY [ 3.270126] Detected MACID = d0:ff:50:0b:0c:a7 [ 3.276431] cpsw: Detected MACID = d0:ff:50:0b:0c:a9 [ 3.284398] rtc-m41t80 0-0068: setting system clock to 2015-07-09 05:43:38 UTC (1436420618) [ 3.298394] net eth0: initializing cpsw version 1.12 (0) [ 3.307340] net eth0: phy found : id is : 0x7c0f1 [ 3.317984] 8021q: adding VLAN 0 to HW filter on device eth0 [ 6.380965] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 6.401111] IP-Config: Complete: [ 6.404594] device=eth0, hwaddr=d0:ff:50:0b:0c:a7, ipaddr=192.168.1.94, mask=255.255.255.0, gw=192.168.1.1 [ 6.415439] host=192.168.1.94, domain=, nis-domain=(none) [ 6.421747] bootserver=192.168.1.68, rootserver=192.168.1.68, rootpath= [ 6.443121] VFS: Mounted root (nfs filesystem) on device 0:14. [ 6.450126] devtmpfs: mounted [ 6.454885] Freeing unused kernel memory: 396K (c0801000 - c0864000) INIT: version 2.88 booting Starting udev [ 7.348464] udevd[1010]: starting version 182 Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory bootlogd. ALSA: Restoring mixer settings... /usr/sbin/alsactl: load_state:1696: No soundcards found... NOT configuring network interfaces: / is an NFS mount INIT: Entering runlevel: 5 Starting system message bus: dbus. UIM SYSFS Node Not Found Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting syslogd/klogd: done Starting thttpd. ioctl FBIOPUT_VSCREENINFO: Invalid argument Starting PVR Error: missing filename. Could not find pvrsrvkm driver Starting Lighttpd Web Server: lighttpd. 2015-07-09 05:43:52: (log.c.166) server started / Starting Matrix GUI application. *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** Stopping Bootlog daemon: bootlogd. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyO0 Arago 2013.12 am335x-evm ttyO0 am335x-evm login: root root@am335x-evm:~# dmesg | grep mmc [ 2.883224] vmmc: at 3300 mV [ 2.886458] vmmc: supplied by wlan-en-regulator root@am335x-evm:~# root@am335x-evm:~# modprobe wlcore [ 265.174130] cfg80211: Calling CRDA to update world regulatory domain [ 265.914682] cfg80211: World regulatory domain updated: [ 265.920113] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 265.928827] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 265.936981] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 265.945116] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 265.953253] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 265.961382] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) root@am335x-evm:~# root@am335x-evm:~# modprobe wl18xx root@am335x-evm:~# root@am335x-evm:~# modprobe wlcore_sdio root@am335x-evm:~# root@am335x-evm:~# ifconfig -a can0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:71 eth0 Link encap:Ethernet HWaddr D0:FF:50:0B:0C:A7 inet addr:192.168.1.94 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57209 errors:0 dropped:6 overruns:0 frame:0 TX packets:24713 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71598684 (68.2 MiB) TX bytes:4060804 (3.8 MiB) Interrupt:56 eth1 Link encap:Ethernet HWaddr D0:FF:50:0B:0C:A9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:144 errors:0 dropped:0 overruns:0 frame:0 TX packets:144 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:249967 (244.1 KiB) TX bytes:249967 (244.1 KiB) root@am335x-evm:~# root@am335x-evm:~# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 no wireless extensions. can0 no wireless extensions. root@am335x-evm:~# root@am335x-evm:~# root@am335x-evm:~# dmesg | tail [ 6.454885] Freeing unused kernel memory: 396K (c0801000 - c0864000) >[ 7.348464] udevd[1010]: starting version 182 [ 265.174130] cfg80211: Calling CRDA to update world regulatory domain [ 265.914682] cfg80211: World regulatory domain updated: [ 265.920113] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 265.928827] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 265.936981] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 265.945116] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 265.953253] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 265.961382] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) root@am335x-evm:~#